First of all sorry for my english not good.
Start : with my HD2 have brick after task29 and not success to flash new ROM I'm take USB. cable out and try to open my HD2 in to boot loader by put volum down + power bottom but screen not show any image or 3 color my phone it only long vibration pull battery out waiting 30 minute and put battery in and try to open my phone to boot loader but is same only long vibration.
Now : can not do any think with it when try to plug power in my phone is auto startup and long vibration.
I'm search on google and in this forum not have some one face problem same as me please help me to fix this.
Any body please help me, I'm love it because now we can run both WM. and Android
Upppp waiting for your help
Did you try a long press of the reset-button?
You could try to put the original Stock Image from HTC onto the root-folder of your SD-Card, rename it to LEOIMG.nbh and Push Vol up + Vol down during start and follow the on-screen instructions if it works.
Otherwise use Search-Function in the forum.
ı have jtag HTC for samsung and HTC devices if u want send for repair to me..
www.sevgigsm.net/forum
admin..
I use ORT
Did you check to make sure your radio version was correct before flashing? This is probably the number one reason for bricking.
Check this thread it may help you if you did the flash properly:
http://forum.xda-developers.com/showthread.php?t=668347
i got same problem now...
no screen, no boot, vol down+ power oso same
no screen just a long vibration
anybody help?
I am using the correct radio so don't tell me I am using a wrong radio or something, I have been flashing for 4 months so I know EXACTLY how to flash.
now i can neither get into tri-color or hard reset so don't tell me to flash or smth like that, just tell me how to recover properly
Don't tell us to use search or something because seems like only 2 of us is encountering this problem in the internet
I'm exactly the same problem as TS coz it juz auto go vibrate when plug in battery
This problem actually started when I flash ROM halfway, it stucked and failed...
the device is already HSPL-ed!!!!
but why the F it cannot get into tri-color bootscreen now?
Also, I have to state that my device already got several problems before, my device was very hard to bootup as it will always stuck at HTC screen w/o red version number at bottom left corner, must keep on removing and reinstall battery and reboot until it can boot, not an issue with rom/radio/sim/sd as I tried flash proper rom and radio and remove sd and SIM.
my device also seems like got problem at the gps chip, because when using it for a few minutes, it will lost signal and never reconnects unless i soft reset, after use gps the device will also use battery VERY FAST(-100mA in standby, from -4mA).
now i cannot flash to stock completely, how do I get warranty it?
at the long vibrate, when i plug in to my pc, it will keep on got usb connected and disconnected sound
and dont know what device is connected as not shown in found new hardware and device manager
I also have been searching all possible keywords about what me and TS encountered but all linked to completely UNRELATED results(like search for long vibrations only link to people asking how to make vibration long and 1st result is this thread)
bountygiver said:
This problem actually started when I flash ROM halfway, it stucked and failed...
the device is already HSPL-ed!!!!
but why the F it cannot get into tri-color bootscreen now?
Also, I have to state that my device already got several problems before, my device was very hard to bootup as it will always stuck at HTC screen w/o red version number at bottom left corner, must keep on removing and reinstall battery and reboot until it can boot, not an issue with rom/radio/sim/sd as I tried flash proper rom and radio and remove sd and SIM.
my device also seems like got problem at the gps chip, because when using it for a few minutes, it will lost signal and never reconnects unless i soft reset, after use gps the device will also use battery VERY FAST(-100mA in standby, from -4mA).
now i cannot flash to stock completely, how do I get warranty it?
Click to expand...
Click to collapse
Silly question, but are you holding (and keep on holding) the Volume-Down button while you press the power button?
of course YES
i told you i have been flashing for so long
Leo from T-Mobile. Hi! I've got same problem. After flashing new (next) rom phone definetely died. Phohe is currently simfree and with HSPL. Only one reaction is short vibration after press power button. I searched everywhere. My phone has no bootloader but system see him as Qualcom CDMA Technologies MSM. Thats all, any ideas? Please and thanks for advice.
czaruch said:
Thats all, any ideas?
Click to expand...
Click to collapse
Yes, you flashed a non tmous stock rom that included a ..51.. radio and it destroyed your phone.
What rom? exact filename please.
thank you so much.
I bricked a Leo with the .51 radio. I think I read that is a European or otherwise foreign radio. Since your ROM has Euro in the name.......
czaruch said:
ROM_Leo_HTC_WWE_EastEurope_1-66.
Click to expand...
Click to collapse
The full filename for that rom is
RUU_Leo_HTC_WWE_EastEurope_1.66.479.2_Radio_CRC_Si gned_15.32.50.07U_2.07.51.22_2_Ship.exe
it comes with a version x.xx.51.x radio, and they do Not work on tmous (t mobile us) phones. They kill them
Your phone is dead, sorry. No known fix.
warranty or repair (or JTAG if you are brave and have the money)
a friend of mine bricked his phone. he then tried to microwave it, but that didn't work after that he took a power wire from an old computer, cut it and connected it directly to the phone's parts where the battery would go...this completely f-ed his phone up (he also used a lighter to fake a powersurge of the battery). Then he called htc and a few weeks later he got a new hd2!
GOOD LUCK
lol, he doesnt need to do any of that, its allready as dead as it can be. Loads of epople have had them replaced under warranty with this kind of brick. It wont start, so htc/tmo cant see that its been hacked.
Hi! I understand and realy sad. Somebody know where could I fix it in UK? And how much for this pleasure. Thanks.
i would contact htc, see what they have to say. (dont say you flashed it, it just stopped working")
Related
I had a problem with the power button not working and I was adviced to reflash the original ROM (I never did a ROM upgrade) so I picked the original and latest Cingular ROM. Flashing strated and then hung for a while @ 80% progress, few minutes after continued up to 95% progress and at that point I got ERROR 326 message (INVALID COMMAND) stating that the NBF file couldn´t be used for this phone. I dissconnected the phone and did a soft reset and what I got was the BOOTLOAD SCREEN and since then I can not make the phone exit from it. Later I tried flashing RUU_RIsidoro_2.26.10.2_WWE+CF2SP1_G4, this time it went all the way to 100% progress and the congratulations screen, I made a soft reset (the only way I know to exit the bootload mode) and I got momentarly the HTC innovation screen and right away dissapeared to enter in bootload screen again.
Then I reflash ROM with RUU_Qtek_9100_AKU2_21878_024711_ESN_G4, this time it went all the way up to 100% and success screen appeared, the phone rebooted and is up and running although with inoperant power button.
Since you've successfully reflashed your phone and the power button isn't still working have you considered a hardware fault?
Look for some info/pics on how to disassemble your wizard to verify if the button is well soldered to the board
luiggi said:
what I got was the BOOTLOAD SCREEN and since then I can not make the phone exit from it. Later I tried flashing RUU_RIsidoro_2.26.10.2_WWE+CF2SP1_G4,
Click to expand...
Click to collapse
Luiggi, pls tell me how to flash the phone while in the bootloader screen?!?
There's no secret to flash while in bootloader screen. Use the RUU file. It might take a little while longer to detect the phone but goes all the way to the end
Yes, it has to be a hardware issue
mestrini said:
Since you've successfully reflashed your phone and the power button isn't still working have you considered a hardware fault?
Look for some info/pics on how to disassemble your wizard to verify if the button is well soldered to the board
Click to expand...
Click to collapse
I´ll try the disassembly and perhaps is not a big deal to fix it, I got a copy of the service manual posted in some of the forums, and I´ll give it a try.
Thanks for the advice!
You just do it!
vlada said:
Luiggi, pls tell me how to flash the phone while in the bootloader screen?!?
Click to expand...
Click to collapse
Try first a soft reset while in the BL screen, if doesn´t react then do what I did:
I just plugged the USB cable and run the RUU!! As simple as that and as risky as the ROM you select not being the right one.
Touch Pro Bricked
Ok so I am a noob and at least I admit it!!! I had been having problems with the display scrambling on my flashed to cricket sprint touch pro so what I did was install Hardspl 37 and tried to do a new flash. I last saw my display say that a problem occurred while flashing to the new rom and now I get nothing when I power up. I have tried hard reset I have tried soft reset I have tried about a million different key combos and I get nothing just the backlight pops on and nothing beyond this point. I get nothing when it powers up ...no startup sounds nothing...Just the backlight pops on and then nothing PLEASE HELP!!!!!!!!!!!!!
IS THIS PHONE A 300.00 paper weight???
Ok so Heres what I have done.... I started the flash from my pc but it didn't take so then I put hard spl 37 on my sd card along with raphimg.nbh and since then I get nothing like I stated above??? also bootloader wont come up the phone powers up but doesnt vibrate like it used to and I get just the backlight??? Some one on another site said to try to manually get into bootloader but I don't know how any suggestions would be greatly appreciated.
Should try pressing volume down button while reseting till you get to bootloader. If not, then...
Oh, and hardspl you want to use is ver 1.90 by Oli Nex. Not sure which one you used.
see bellow
http://wiki.xda-developers.com/index.php?pagename=Raphael_HardSPL
Another thing that might have caused this is flashing gsm rom on cdma device (which is your case I suppose - Fuze). Make sure that rom you are flashing is for your device (either raphael (gsm) or fuze(cdma) ).
To get into boot loader hold down the vol down key while turning on the phone.
Best way for you to try is to take out the battery, put it back in, hold down the 'volume down' button on the side and press the power button.
Sorry that's all i can help you with. Hopefully someone else has had this happen and knows a way out of it
lindenny50 said:
Touch Pro Bricked
Ok so I am a noob and at least I admit it!!! I had been having problems with the display scrambling on my flashed to cricket sprint touch pro so what I did was install Hardspl 37 and tried to do a new flash. I last saw my display say that a problem occurred while flashing to the new rom and now I get nothing when I power up. I have tried hard reset I have tried soft reset I have tried about a million different key combos and I get nothing just the backlight pops on and nothing beyond this point. I get nothing when it powers up ...no startup sounds nothing...Just the backlight pops on and then nothing PLEASE HELP!!!!!!!!!!!!!
IS THIS PHONE A 300.00 paper weight???
Ok so Heres what I have done.... I started the flash from my pc but it didn't take so then I put hard spl 37 on my sd card along with raphimg.nbh and since then I get nothing like I stated above??? also bootloader wont come up the phone powers up but doesnt vibrate like it used to and I get just the backlight??? Some one on another site said to try to manually get into bootloader but I don't know how any suggestions would be greatly appreciated.
Click to expand...
Click to collapse
Step 1. Take a deep breath
Step 2. Search and read... sounds frustrating buts lots of devices have been brought back from the dead.
Step 3. Get the phone to bootloader mode (three horizontal color bars)
Step 4. Read some more or read other posts on what to do because I can't help past this!
I think you may have used the wrong SPL so start looking there.
I saw what Bauerpavel just posted... good stuff
If you can get to bootloader mode you should be able to start all over again from here
http://forum.xda-developers.com/showthread.php?t=448008
If you're running a Sprint Touch Pro, most of the roms here are not for your phone. May want to try ppcgeeks.com
bauerpavel said:
Make sure that rom you are flashing is for your device (either raphael (gsm) or fuze(cdma) ).
Click to expand...
Click to collapse
Just to be clear, not to be confused with the AT&T HTC Fuze, which is a GSM device!
But you're with Sprint, so assuming you're in the US, you have a CDMA device. Check the CDMA forum at the top level of the Raphael forums. There will be lot's of good advice there on the specifics for that hardware.
Good luck!
bauerpavel said:
Oh, and hardspl you want to use is ver 1.90 by Oli Nex. Not sure which one you used.
see bellow
http://wiki.xda-developers.com/index.php?pagename=Raphael_HardSPL
Another thing that might have caused this is flashing gsm rom on cdma device (which is your case I suppose - Fuze). Make sure that rom you are flashing is for your device (either raphael (gsm) or fuze(cdma) ).
Click to expand...
Click to collapse
Fuze=AT&T=GSM
Sprint TouchPro = CDMA
If you tried flashing a GSM ROM to a CDMA phone you may be up the creek!
After ROM upload my HTC Hero show only some logo like device out of box. Nothing else is going. Button combinations for bootloader access is not working. Any ideas?
I managed to skilfully brick mine too, is a there a way to get it to boot up via key combination or using USB from a computer?
We are three now.
I know (presumably) my error: I flashed an SPL zip package that could be of the wrong type (Dream).
The boot shows the phone logo (mine says G2 T-Mobile).
The home keydown at boot doesn't work.
Is there a possibility to unbrick it?
Hope someone tells you how to unbrick it as I was about to do the update the ROM, not sure I want to do it now.
Right this is very weird as i had the same picture on my phone and thought it was bricked too..
BUT i just did a soft reset call menu end together. Then i did a hard reset as i wasnt sure if the soft one had done anything. Battery out then in and start up phone whilst holding down house and back key and then it started to boot up. So not sure if this helps anyone i doubt it as its very random but i thought id share just in case!!!
I had just flashed my radio when mine did this..
friend of mine had tha problem too, he had to send his device to htc.. 50 bucks ;-)
hmmm ... i am one of u guys now ...
no matter what key-combo i press, it just show a BOX and an arrow and a phone ... 3 sec later, phone turns off, no matter hwat key u press, it is not doing anything until u unplug the batery ... then when u turn it on, it repeat the same thing again
check if you can access fastboot via back+power when the phone is off. if so install recovery image and then install correct rom. if not i guess you're screwed, not sure though.
This guy
http://forum.xda-developers.com/showthread.php?t=556038
seemed to have the same issue and resolved it.
Hope it helps/good luck!
sonatbey said:
i bricked very bad no screen no logo not booting. anyway any helps
Click to expand...
Click to collapse
Please be more explicit as to what exactly you did.
(for someone to help you)
OK title says it all, and yes I have been reading for the last 3hrs, all the possible solutions.
HD2 EU Vodafone UK
So here is what I have tried:-
Task 29 + flash stock rom - stuck -
Hard reset - stuck
remove HSPL - stuck
flash latest Vodafone rom from HTC 3.14.161.3 - stuck - also SPL now 3.03
flash old stock to downgrade SPL to 1.66 - stuck
Have also tried reinstalling MAGLDR - stuck - magldr doesn't even show.
I never get flash failed, and yet it will not get past the Tri coloured bootloader.
Also I cannot get it to flash from SD. I have tried holding the endcall and vol down but it just goes to the loader.
Vol Up and endcall goes to hard reset.
And, to make it worse, it's not even mine. I was returning it to Winmo for a mate.
Phones been running Android nand since March without problems.
All suggestions welcome.
Bixx said:
Vol Up and endcall goes to hard reset.
Click to expand...
Click to collapse
that would indicate a stuck volume down button, since hard reset is volup and voldown. (You dont need to hold power, tap and release it, its teh vol buttons you hold)
You are quite right about the vol up and down for reset.
Also, I had been considering the possibility of a stuck button.
I will see if i can prove or disprove it.
Thanks for the response.
Does anybody know how many buttons are in the volume control rocker?
Is it:-
1 for down volume
1 for up volume
and another for both when you hold both in?
I am still trying to decide if the down volume button is stuck on.
When I hold both down I can get into reset mode, but if I only press the up it still goes to tri colour.
So I am still not sure if the down is stuck on.
3 buttons in the rocker could explain why up only doesn't go to reset but 2 buttons only would confirm that the down is not stuck on.
All comments welcome
two, you can feel them click on individually when you press them.
I too can only feel 2 and that would imply that the down is not stuck.
When I hold the up button and switch on it goes to boot loader, if it was stuck shouldn't the phone have gone to reset?
I was hoping it was like a mouse wheel with forwards, backwards and click down which is 3 positions.
I'm running out of things to try.
If it's not stuck why does it keep going to bootloader with out being asked?
Why can I flash roms and HSPL without any failure messages but still find no change on reboot?
Thanks for the replies and please keep them comming
I have managed to flash from SD. I tried a different card.
I have attached a pic of the screen saying update complete, update success.
But still stuck in bootloader
well, if it isnt hardware, it must be a corrupted bootloader issue, or bad nand blocks perhaps. ive seen quite a few 'only enters bootoader' threads over the yrs, but never really noticed a solution.
sorry, no suggestions, other than perhaps give teh freezer trick a go?
I'm desperate enough to try almost anything.
I will have to read up on the freezer trick.( don't want to kill it completely)
I have also contacted a couple of repairers for a quote using Jtag. the first said "sorry bricked" and I'm still waiting for the second reply.
Also reading up on Goldcards, maybe that's another option?
Thanks again for the reply.
Bixx said:
I'm desperate enough to try almost anything.
I will have to read up on the freezer trick.( don't want to kill it completely)
Click to expand...
Click to collapse
cant hurt to try.
I have also contacted a couple of repairers for a quote using Jtag. the first said "sorry bricked" and I'm still waiting for the second reply.
Click to expand...
Click to collapse
lol, probably scared of doing it (it requires dismantling teh phone, and theyre notoriously easy to break, there are loads of threads here where someone took theirs in for a fix and the vol/bottom button/screen ribon cables got broke by the shop.
Also reading up on Goldcards, maybe that's another option?
Click to expand...
Click to collapse
could be tho unlikely (sorry) goldcard flashing is just sd flashing but bypasses carrier and region checks.
if you can get the serial of your sd card, i can make you a goldcard image, no problem. (Don't bother using the free goldcard page on revskills website, its for android and wp7 phones) . PM me the serial and an email address if you want one.
@samsamuel Thanks for all your help and advice.
I have sent it off for repair today.
As I said in the first post, it's not even mine I was re flashing winmo 6.5 so my mate could sell it.
Hopefully it will be all sorted now.
Update.
I contacted 3 repairers.
1st said "sorry dead"
2nd said "£40 + postage"
3rd said "£21 which became £29 all in"
So I sent it to 3rd one, got a quick reply "sorry unable to fix, here is a full refund" and they returned it via 1st class post.
So yesterday I've got the phone in my hands, poped in the battery and I am presented on screen with a triangle and the words "flash failed please try again"
So task 29, now back with a tricoloured screen. See attached.
Now tried a custom Winmo, and it works
So I tried 2 Vodafone and 1 O2 stock roms and they all failed at 9%.
Tried another custom Winmo, and again working
So finally, I have task 29, CLK, clockwork v5 and latest MIUI. All working just fine.
Is there a stock looking custom winmo that anybody can recommend?
Hah, a lucky outcome. The radio is stuck, hence stock roms failing, but lucky for you its still a working radio, so customs are working. About the best result you could get, considering.
I'd say try the Artemis rom, but that will require spl 3.03.hspl, and occasionally the stuck radio issue messes with changing spl,,
Not so sure about your stuck radio theory, I have been able to change the radio without an issue.
I will give Artemis rom a go.
thanks for all the support.
Merry Christmas
Bixx
Hi there!
This thread is my last hope, so please dont let me down folks...:cyclops:
The story short - one sunny morning i turned on my HTC Nexus One and it got stuck with te X on the screen for about 15 minutes, non of the buttons responded, so i did the first thing that came in my mind - i pulled out the battery. After inserting the battery the phone went full brick, i mean literally, no reaction on anything, even conected to the wall charger, there is no sign of life, no charging LED, nothing. Connected to the PC, it says USB device not recognised.
I dont think this is a hardware proble, the phone workwd fine until this interrupted power on. Phone runned on stock Androud, i have not played aroun with it - no bootloader unlock, no rooting.
I searched the internet for a solution, tried a lot of button combinations like in this thread:
http://forum.xda-developers.com/showthread.php?t=1069032
but still no luck, i cannot restore or flash it while my PC does not recognise the phone.
Found some info about those Usb Jig things, but they work only on Samsung phones, so, is there a way to force the phone to go in recovery mode, or give any sign of life so i can try to recover it or flash a diferent ROM?
The warranty has ended, so no hope there.
Hope there is a way out of this, and, sory for my bad english. :good:
Veesais said:
Hi there!
This thread is my last hope, so please dont let me down folks...:cyclops:
The story short - one sunny morning i turned on my HTC Nexus One and it got stuck with te X on the screen for about 15 minutes, non of the buttons responded, so i did the first thing that came in my mind - i pulled out the battery. After inserting the battery the phone went full brick, i mean literally, no reaction on anything, even conected to the wall charger, there is no sign of life, no charging LED, nothing. Connected to the PC, it says USB device not recognised.
I dont think this is a hardware proble, the phone workwd fine until this interrupted power on. Phone runned on stock Androud, i have not played aroun with it - no bootloader unlock, no rooting.
I searched the internet for a solution, tried a lot of button combinations like in this thread:
http://forum.xda-developers.com/showthread.php?t=1069032
but still no luck, i cannot restore or flash it while my PC does not recognise the phone.
Found some info about those Usb Jig things, but they work only on Samsung phones, so, is there a way to force the phone to go in recovery mode, or give any sign of life so i can try to recover it or flash a diferent ROM?
The warranty has ended, so no hope there.
Hope there is a way out of this, and, sory for my bad english. :good:
Click to expand...
Click to collapse
Well no, bricked is a term used when you are rooted and flash a bad rom,kernel,etc. You have no root, so you cannot be "bricked". Just a software failure, you cannot flash another rom because, again, you have no root or custom recovery. Your best bet is trying to send it back to your carrier and get it replaced
ParanoidKang said:
Well no, bricked is a term used when you are rooted and flash a bad rom,kernel,etc. You have no root, so you cannot be "bricked". Just a software failure, you cannot flash another rom because, again, you have no root or custom recovery. Your best bet is trying to send it back to your carrier and get it replaced
Click to expand...
Click to collapse
The warranty time is out, so there is no help from the carrier, unless for cash...
But there must be a way to bring it back to life.
Veesais said:
The warranty time is out, so there is no help from the carrier, unless for cash...
But there must be a way to bring it back to life.
Click to expand...
Click to collapse
Now the screen may not show, but try booting into fastboot mode by press and hold the Trackball+Power buttons together.
I'm not sure about the nexus one, but newer nexus devices have factory images, supplied by Google. If they exist for the nexus one, you should be able to save your device by flashing them through fastboot. That is if the images exist and you can get to fastboot.
Sent from my Nexus 4 using XDA Premium 4 mobile app