Hello!
To begin, forgive my uncertain English!
I had recently a Htc Diamond, but I've lost it, I want now use my old HTC TyTN, but I am a little lost in all versions of Hard Spl, I have first unsimlocked and uncidlocked the phone with this topic : http://forum.xda-developers.com/showthread.php?t=293665
What do I do to install a new rom with WM 6.1, and what are the Roms advised at this time?
Thank you in advance, and please forgive me, I have a little trouble to go the forum in English, so I am really lost!
ROM: 1.23.163.5
Date: 06/18/06
Radio 1.16.00.00
Protocol: 32.53.7018.01H
Update the Hermes with Hard SPL V7 - should read IPL - 1.04 & SPL - 2.10oli when finished update and go to the tri-colour screen.
After that go to the WM06 part of the Hermes forum. You'll find a sticky with some older ROMs and a heap of newer ones in production.
As you've now got Hard SPL V7 on you can use the sd card method to install roms.
backup the sd card 1st.
1. Format 2Gb or less sd card FAT32. Copy .nbh file(rom you want) on it and rename to hermimg.nbh .
2. insert sd card back into Hermes and boot to tri-colour screen.
3. As long as you did everything right, follow the prompts. reset with stylus if nothing happens and check sd card is formatted right and .nbh is named right.
Cheers...
Ok to the Hard SPL, with the Hard SPL V7, it took less than a second, then soft reset automatically.
How do I check that it is hard-spl to avoid a crash? (How am I going to tri-color screen? He has done it alone ..)
So thank you for the little tutorial, I think now install the V8 b2 found here: http://forum.xda-developers.com/showthread.php?t=421337
Other recommendations?
Thank you again!
Hold power button, OK button above flywheel and reset with stylus. Hold in until you get to the tri-colour screen. It should display IPL - 1.04 & SPL - 2.10oli.
This means SPL upgrade was a success...
Cheers...
Yeeessss! So cool! : D I can test new ROM now ... A preference for one of them? (I do not know of any developers to Hermes, then to find a good rom in english ...)
By against, I don't have access to the Internet by my operator, how to configure connections for Bouygues Telecom? (French network ..)
Thank goodness you're here!
Go to the wm06 part of the Hermes forum for roms. Look for one that has a network setup wizard and make sure it either has or you install Arcsoft mms composer before runniong the network setup wizard. Should install settings for mms on the Hermes.
Read the discriptions of the roms by the chefs as they tell you about everything in he rom, its up to you to decide whats best...
Cheers...
You can get French ROMs as well...write it in the search bar
Related
Just got Hermes vodafone with German language and successfully loaded hardspl and have it in supercid. Now i want to upgrade to english version, but i keep getting error 260. PDA stays in RGB mode and saying USB. If i disconnect the cable it switches to Serial.
I have tried to update with
vodafone 1.20.161.6 aku 2.3
vodafone 2.07.161.1 aku 3.3
htc 1.35.255.102 aku 2.3
they all report the same. Have tried rebooting computer as said in wiki, but no success.
i now use original
HERM200
ROM 1.20.126.3
RADIO 1.16.00.0
any idea?
Thanks
Are you sure it is a supercid? Write the SPL, can you boot os?
Yes, i can boot os fine.
SPL-1.40.Olipro
IPL-1.01
I did supercid procedure with success....at least i thoughts so. It's my fist upgrade, so anything is possible. I used HTC Hermes SIM & CID Unlock - v3a
Thanks
I have the same problem with my second-hand JASJAM. The only way I can flash ROMs on my phone is by using RUUWrapper and select force SSPL and this always works well.
COME ON people!!!
A simple search would have remedied this...its been a topic so many times now!
The reason the official RUUs wont work correctly is because of the fact that HardSPL has been loaded, hence the SPL version isnt recognised, you gotta flash the official .nbh file using CustomRUU.
But first update to the latest version of HardSPL (see the sticky thread).
When you run the customRUU program select your SPL version (or use autodetect) and off you go!.
EDIT:: to get you started, Hardspl is HERE.....flash it.
then open the RUU with winzip or winrar and copy over the .nbh file into a folder.
download CUSTOMRUU.....run it from that folder with your device synced over activesync....select your SPL and voila.
Silly fella's. Its alright though I used to make the same mistake. I think im better friends with the search feature on here than I am with my real friends. You can always rely on the the WIKI or the search.
Thanks for help mrvanx i manage to flash with no problems now.
Promise to read more wiki next time
My problem was the same described in this post (too recent SPL).
I similar problem only difference is now phone wont go out of boot mode as its not recognised by active syn or in the rom update procedure.
Please help urgently cannot restore phone...and i dont know how
If you have Hard SPl V7 installed, try to re-install the rom, or a different one using the sd card method.
1. Format 2Gb or less sd card FAT32 and copy .nbh file onto it. Rename to hermimg.nbh .
2. Insert into Hermies and reset into bootloader, hold power, OK button under flywheel and reset with stylus hold all buttons in until you get to tri-colour (bootloader) screen.
3. Follow onscreen instructions...
Cheers...
Hello,
I would like to upgrate Rom with this one: Schaps_WM6Pro_Hermes_4.31_WWE_Full.exe
I installed Hard-SPL and now I have 2.10.olipro SPL version displayed in the bootloader (before I had 1.4).
Actually, in my Hermes300 I have installed :
WM6.0
ROM: 2.54.258.2
ROM date: 07/06/07 (DD/MM/YY)
RADIO: 1.47.00.10
Protocol: 32.80.7020.20H
ExtROM: 3.54.258.102
I don't know if it is the original ROM upgrade from HTC website, because I'm not the firt owner of the phone.
Anyway, If I try to upgrade it by using autodetect mode an error occurs:"Error, Unknown version! You should pick safe SSPL".
Why? What Do I have to do to have Upgrade? Maybe, is there still some kinda of "brand"? Which option should I have to select?
I want to use the most safe upgrading procedure to avoid brick.
P.s. I'm using Windows Xp.
Thanks!!
Pick safe SSPL..... Follow the instructions after OR use the sd card method.
Format sd card fat32 then copy the .nbh file onto it. Rename it to "Hermimg.nbh". Put it in phone and reset to bootloader. Hold down power button, ok button above flywheel and reset with stylus. Hold all buttons in until you get to tri-colour screen. It should recognize the flash image so then follow the prompts.
Find this safer than pc flash.
Cheers......
Thank you very much I will do it!
But I'd like to understand why autodetect mode doesn't work! Do u hava any ideas? Cannot I choose SPL-2.02./2.10/2.30 New Bootloader and is it HARD-SPL choices? I'm a newbie in upgrading and I only understand that to avoi brick I should use HARD-SPL. If I use Force safe SSPL or SD card method can I have a brick?
How about if autodetect doesn't work because I have installed original ROM upgrade from HTC? It is possible?
Thanks.
No flashing method is a guarantee of success. Hard SPL isn't either, it just makes it easier or even possible to fix your phone. If you interrupt a flash you will brick your phone but with Hard SPL its possible to fix. Except if you interrupt the radio rom portion of the flash. I think its OK to say that if you stuff up this part of the flash you won't be able to fix easily, if at all.
Most, if not all, cooked roms DON'T have a radio rom inside. ALL stock roms do.
This is why I said its safer with sd card method. You would have to physically reset the hermes in the middle of a flash to stuff it. With the pc, usb cables can be unplugged, reset buttons can be pushed and blackouts/brownouts do occur. Thats if Activesync doesn't throw a hissy fit and disconnect while trying to update....
>HARD-SPL just makes it easier or even possible to fix your phone.
Ok, and by using SD CARD procedure is it the same?
I mean...now with HARD-SPL installed on hermes can I use every upgrading procedure to fix my phone (if possible)? Or to take advantage from that do I have to use a particular procedure?
Before writing here I read a post where another guy had my same problem and some people answered him to choose SPL-2.02./2.10/2.30 New Bootloader and is it HARD-SPL. But u think is better by SD CARD.... .
Thanks, and I'm sorry for many questions!
Does Schaps_WM6Pro_Hermes_4.31_WWE_Full.exe have a radio rom inside? I can upgrade only Rom without RADIO? If yes...how?
Thank you very much!
No, Schaps_WM6Pro_Hermes_4.31_WWE_Full doesn't have a radio rom. Look at the list of apps and tweaks included. It will tell you what radio version it has if it has the radio portion included...( this is for ANY cooked rom. The chefs work hard to make these and are rightly proud of their work.)
Here are the instructions for sd card flash again if you missed the first time
1). Format sd card fat32 then copy the .nbh file onto it. Rename it to "Hermimg.nbh".
2). Put it in phone and reset to bootloader - Hold down power button, ok button above flywheel and reset with stylus. Hold all buttons in until you get to tri-colour screen. It should recognize the flash image so then follow the prompts.
Its that easy when you have Hard SPL on your phone...
Cheera...
It worked very well. Thank u very much!
Sow if you don't have Hard Spl on your phone the SD flash method won't work? I have a spv m700 and coun't manage to install hard-spl.
Go to the last few pages of the Hard SPL thread - its a sticky - You'll find out how to install Hard SPL using the sd card method. Don't have to worry about sync errors with the PC then...
Cheers...
I have got Hard-SPL 2.60. Which one should I pick in the SPL Meny? I'm kinda noobish when it comes to this ...
I hope someone can help me , i ve tried a lot of roms, and i cant upgrade it, i also tried the sd flash , but it got stuck on the boot screen , could someone please help me, what should i do?
I've been doing a lot of wiki reading before trying to upgrade to a custom ROM. When I enter bootloader mode I see this on the tri-colored screen:
Herm100
IPL-1.04
Herm100
SPL-2.03
(at the bottom)
Serial
...I thought it should say SPL 1.04
Do I have 1.04???
The number after SPL- is the bootloader version, so you have 2.03
If you seriously want to flash roms safely, You need spl 2.10 olipro. Go to Here to find it - http://forum.xda-developers.com/showthread.php?t=296722
Cheers...
When I say safely, I mean as safe as you can get. There are NO GUARANTEES flashing roms...EVER...
Which one do i need
You said, "If you seriously want to flash roms safely, You need spl 2.10 olipro. Go to Here to find it - http://forum.xda-developers.com/showthread.php?t=296722
...I don't see 2.10 olipro...
I'm seeing 2.10 Hard, or 1.10 olipro
I really don't know what i'm doing, so can you tell me which of these I need for my AT&T 8525, English phone? I'm basically just wanting to try some other ROM because the factory one seems so slow. I'd ask for recommendations but I guess it depands on what you're doing with your phone. I just use it to view office docs, and I use Pocket Informant. But it seems very slow compared to my former pocket pc. And it very slow compared to the iphone that I've seen in operation by my friend.
You need Hard SPL V7. Its at the bottom of the 1st post.
This makes it easier (or possible) to recover your device if a flash goes bad. It also allows you to flash using the sd card method which I, personally, believe is safer than using the pc.
After Installing Hard SPL ( you can use sd card to install this. Apps needed and instructions are on page 116, post 1160) do this -
1). format sd card fat32 and copy the .nbh file of the rom you want to it. Rename to "hermimg.nbh".
2). Put Hermes into bootloader (tri-colour screen) - hold Power, OK button above flywheel and reset with stylus until bootloader comes up.
3). If you formated the sd car fat32 and renamed the flash file properly the Hermes will recognise it and say to hit power button to start flash - hit power button. Wait until it says flash complete then reset with stylus
Just make sure you have plenty of 50 % (or more) battery power.
Cheers...
Hi Guys
Recently took delivery of 2nd user TMobile MDA Vario II with WM5
Tricolour screen showed
Herm300
IPL-1.01
Herm 300
SPL-1.04
Following advice posted here I Downloaded and Installed HardSPL . Following this the Tricolour screen shows
Herm300
IPL-1.04
Herm300
SPL-2.10 Olipro
When I try and install a WM6 ROM via the appropriate RUUWrapper I get the following error message when I select the Autodetect button
Error,Unknown version,You should pick SSPL
Any advice greatly appreciated
Thanks
ROM has to be a Hermes ROM.
Would also suggest using the sd card method if you get no love from the PC.
1. Format sd card (2Gb or less) FAT32.
2. Copy .nbh file of the rom you want onto sd card and rename to hermimg.nbh .Insert back into Hermes.
3 Put Hermes into bootloader - hold power, OK button above flywheel and reset with stylus, hold ALL buttons in until you get to ttri-colour screen. If you have done everything right, follow the prompts.
Hermes ROM's always have .nbh files as the rom, if you have ANY other type then its not a Hermes rom and Hard SPL shouldn't let you install.
Cheers...
Hi - followed advice exactly and worked first time - many thanks
When i tried to install any firmware the progress stop at 11% and the Hermes only turn on in bootmode, any idea??
rmorera84 said:
When i tried to install any firmware the progress stop at 11% and the Hermes only turn on in bootmode, any idea??
Click to expand...
Click to collapse
I had that problem and few more with my Hermes.
While it didn't help me, this suggestion by ultramag69 may help you...
Use the sd card method to flash a new rom, instead of a USB cable/Windows computer.
1. Format a 2Gb or less sd card to FAT32, copy the large 50MB-90MB .nbh file onto it and rename to hermimg.nbh
2. Insert the card into your Hermes and reset to bootloader (hold OK & POWER and push RESET for a sec with the stylus)
3. If you haven't stuffed up the other steps, follow the prompts.
Hope this helps!
Just one other thing summoner, make sure you have Hard SPL V7 installed. Otherwise the ONLY rom I'd try flashing like that is the SHIPPED STOCK ROM. Its so the CID will be recognised and won't cause a brick.
rmorera84, unless you've installed Hard SPL V7 then find the SHIPPED STOCK ROM and flash that, anything else may permanently brick your Hermes.
If you have Hard SPL V7 (IPL 1.04, SPL 2.10 oli) then flash what you like...
Cheers...
- Installed latested Orange rom, that I know of - SPV_M3100_ROMUpdate_1007
- installed Hard SPL 7 & applied SIM unlock/super CID
- re-installed TNT TNT.19199_Professional_Hermes
The result is:
IPL-1.01
SPL-1.40.Olipro
I suppose I should upgrading the radio rom now!?
I am told don't try fixing what isn't broken - and it is working. 3G iNet, Phone, WiFi, BT - all good atm.
Or is there a particular update I should still install?
Thanks!
SUMM0NER, you're using an older, not so safe version of Hard SPL. The Hermes is downgraded to SPL 1.40 when you sim/CID unlock your phone. Best idea would be to re-install Hard SPL V7. Its a later version that seems less prone to problems when flashing.
Go back to the Hard SPL thread and get Hard SPL V7. I had the same thing happen to me when I unlocked the Hermes, nearly cost me my handset.
The steps are unlock Hermes, Install Hard SPL then upgrade OS.
Cheers...
Do I need to re-apply the OS rom file?
I just reinstalled Hard SPL7, now shows as IPL-104, SPL-2.10.Olipro.
Thanks!
My hermes only work whit this rom:Schaps_WM6Pro_ESN_3.54b-0808_Full
Because whit any other rom they stuck at 11%.
This is the info or the phone:
IPL-1.01
Spl-1.40.Olipro
Whit the first rom the htc boot but the phone funtion don´t work.
rmorera84, refer to my last post.
SUMM0NER, no. You have loaded the os, the reason you put Hard SPL V7 is if you want to upgrade the radio rom (not a good idea unless you are experiencing problems) or wish to change the os. Just means recovery is easier than if you didn't have it.
Cheers...
Many thanks ultramag69.
rmorera84 what branding is your Hermes (ie: Orange M3100, T-Mobile Vario 2, Vodeaphone V1605 etc...)?
Can I assume your Hermes is working right now?
If it is download and install HardSPL V.7 (attached to the bottom of the first post!)
Ones done verify that it installed correctly by holding the OK & Power button and pushing reset for a sec. The screen should display the coloured bars and say towards the centre: SPL-2.10.Olipro
It´s Cingular 8525, i could install the HardSPL V.7, now what rom i can flash??
You didn't confirm if it is working right now!?
If it is not working, try one of the official WM5 Cingular roms from this list. If that worked apply HardSPL 7 and take it from there.
Ones you downloaded the Cingular rom update you will have to keep unpacking the .exe files until you come to the actual .NBH file (WinRAR works for me).
Then follow ultramag69's instructions on flashing the rom via memory card.
Works, now i have this info:
HERM100
IPL-1.04
HERM100
SPL-2.10.Olipro
I download the official Cingular WM5 rom, but. i don´t know how install this rom by memory card, could you help me??
Excellent!
Try downgrading to the Cingular rom via USB. Just double click the EXE and follow the instructions.
To use the memory card method follow these steps...
0. unpack the .exe file containing the rom with Winrar (right-click exe then choose "Extract to...\")
1. Format a 2Gb or less sd card to FAT32, copy the large 50MB-90MB .nbh file onto it and rename to hermimg.nbh
2. Insert the card into your Hermes and reset to bootloader (hold OK & POWER and push RESET for a sec with the stylus)
3. If you haven't stuffed up the other steps, follow the prompts.
The reason to use the memory card to upgrade a rom, rather than a usb cable, is to cut down on failed upgrades (dodgy Windows/usb port/usb cable/etc..).
All working? Try upgrading to a Hermes rom that didn't work previously.
Any rom you can find in the Hermes section. Go to the WM06 part of the forum, theres a sticky at the top with about 50 older roms and you'll find other roms there too (latest is wm6.5).
Cheers...
i install the official WM5 AT-T version the WM6 AT-T, but, i still whit the no-gsm problem, can i flash i radio? or what i can do??
You may not be able to fix this, if you know what the original SHIPPED STOCK ROM was and can find it, then flash that. It may not work, if it gets stuck at 11% - 17% mark it means the radio ROM is stuffed and the memory area is corrupted. Not fixable.
You could also try, if you know what it is, the original radio rom by itself. Again, if you can't get it to work, you have a PDA but won't work as a phone ever again. Sorry to be the bearer of bad news.
Im to having the same problem, it keeps going back to the 2.1.Olipro boot loader.
I tried the memory card option and it starts to install but then stops.
Does anyone have and sugestions?
Cheers
Help Help
Hi, I got my Hermes 8525 in boot mode what i did is to install this Schaps_WM6Pro_WWE_4.00_Full.exe now my hermes is working but i want to unlock it..what can I do cos everytime i try got in to boot mode again..any help tks.,..