I just upgraded from my old harrier, trying to figure out the extensive information avaliable on upgrading the titan.
So, Rom: Telecom, 1.30, boot loader v1.40
http://wiki.xda-developers.com/index.php?pagename=TitanStockHome
On the main stock thread, it says:
The nueROM web site indicates that nueSPL version 2.47 is designed for the HTC Titan with GPS enabled only (ROM versions 3.xx or higher)
Click to expand...
Click to collapse
Obviously this isn't the right bootloader, and therefore i can't use that bootloader. Also this seems that I can't load 3.xx roms.
http://wiki.xda-developers.com/index.php?pagename=TitanOtherHome
Looking at this page, there are several different radios listed, but I can't see any that do windows 6.
Can anyone tell me what upgrade path I need to take to get windows mobile 6?
I don't even know what type of rom will work with my telecom phone :\
Any assistance appreciated.
You CAN unlock via nueSPL 2.47
Myself i unlocked via olipro 2.4 <-- unlocking this way is not for the faint of heart ..
Once you have done this, you can load a Sprint radio rom version 3.35.04 onwards then ..
you can then load a WM6.1 GPS enabled, Rev A EvDo, rom, as well as have the capability to use an 8GB Micro SDHC SD Card..
If you don't note down your EvDo password before upgrading, you will lose EvDo speed and be stuck with 1X mobile broadband speed
or you can save some heartache and let me do it for you for a fee send me a PM
I may have to take you up on that, but I will give it a go myself first because i want to figure out how to do this.
I tried running the getspl.exe on my phone, to try and recover my msl number, but it just crashed on execution.
Are there are other ways of doing this?
getspl..
dont bother, it doesnt work on the telecom titan.
.. much to learn you have, young skywalker
our MSL is 482826
i) to get to the EPST menu, enter ##778 then press talk
ii) click on "edit"
iii) enter the MSL given above
on the left hand side menu, click on security
go to the security settings and save the HDR AN AUTH LONG password <---- this is vital.
This password is lost during the radio rom flash. After unlocking, flashing the radio rom and then the OS rom, you can re enter the HDR password back into EPST.
Keep me posted
actually you cant unlock via nueSPL 2.47.
Because the Telecom Titan is WM5 with a non GPS Rom, the you can only unlock via HardSPL 2.4.
nueSPL 2.47 only unlocks GPS enabled roms.
sorry for the wrong one, i was thinking in terms of a post flash rom.
Cheers
Hey, so just to make sure I understand what i'm doing here before i take the final steps, does this sound right?
1) Save HDR info
2) Unlock phone with HardSPL 2.4.
3) Rom: Telecom, 1.30, boot loader v1.40
4) Install 3.2x.Hard SPL and flash the SPL
5) download desired rom
6) install rom (somehow), most likely the Titan R4R.
This will allow me to use my phone, have win6 and gps, correct?
Thanks!
Related
So I was in the middle of upgrading to the "Official Sprint Rom" using 1.2Olipro in order to jump on the DCD 3.0.1 bandwagon. I guess this was a bad idea because the phone rebooted at 11% and now I'm back to the bootloader. The problem is, I don't know what to do. I don't want to make things worse so for now I just left it in the bootloader.
Prior to attempting the flash I was running
DCD 2.0.0 /w Radio 3.27 (2.4Olipro).
Just before I flashed the Sprint rom I flashed the 1.2 bootloader.
I'm stuck, what do I do now?
Tom
check this link out:
http://forum.ppcgeeks.com/showthread.php?t=17667
You didnt need to install olipro 1.20. Install olipro 2.40 again and you will get your device bootable again.
You may find that you have fried your radio. when the device reboots after the olipro 2.40 is back on you can check the message on the first screen to see if the radio is there or not. If there is no radio just reflash sprint 3.35. If the radio is there the device will reboot into your old configuration.
Then just flash the sprint offical 3.35 and this will give you then new radio. Then flash dcd 3.x.x
The instructions are right in the first few posts of the 3.0.1 thread.
I can't install 2.4 because it requires an activesync connection. The phone is currently in bootloader so no activesync. Should I reboot the phone? I don't want to make a bad situation worse.
Tom
you dont need active sync, put in bootloader and plug it into the computer and run the bootloader upgrade...should work
You might have to flash a radio and rom via sd card method. The radio and roms will have to be compatible with olipro 1.20 otherwise it will continually reboot once it is all flashed.
I am sure there is a method to get you back to olipro 2.40 without activesync so you might search a bit first. But if you cant find out how, then the sd method above will at least get you back working.
Unfortunately dropping back to a non gps radio (compatible with olipro 1.20) will probably hose your MSID etc so I hope you wrote them down.
Anyone more knowledgeable than me might comment further but do a bit of searching in the meantime.
friguy33 said:
you dont need active sync, put in bootloader and plug it into the computer and run the bootloader upgrade...should work
Click to expand...
Click to collapse
I have 2 .exe's:
Hard-SPL-MFG.exe and titan_SPL_2.40-olipro.exe
when I run either:
*
* P4000/PPC6800/xv6800/Titan/Mogul UnLocker utility
*
* Total process may take about 5-10 minutes depends on CPU speed.
*
Connect your device via activesync before continuing.
Press any key to continue . . .
Initializing
When you reboot, do you get a screen telling you the bootloader, radio and rom versions?
To exit bootloader to check, you can use ImCoKeMaNs exit bootloader program.
SOLVED!
I was able to flash Sprint v2.09 ROM. After the phone rebooted and the Calibration screen came up I was able to upgrade to Olipro 2.4. Right after that I ran the 3.35 Sprint update which went through. As soon as Windows was back at the calibration screen, I went back into 2.4 bootloader and ran the DCD upgrade. Up 100% and incoming calls work so it looks like the MSID was preserved.
Cheers,
Tom
Hello everyone i Just got a xv6800 and am trying to flash to a newer rom...However i cant seem to boot into the bootloader it just hangs at Loading.... There is nothing installed its factory rom and settings
Thx in advance
How are you attempting to load into bootloader?
The way I saw on the forums....holding power and camera button and hittig the reset..i get the tri color screen then it goes to Loading... and just sits there dosnt do anything else
Do you have a microsd card in while trying this? If so, does it contain any .nbh files on it in the root directory? If so, do you have a TITAIMG.nbh file in the root directory?
The only way the bootloader would try loading something the way you're describing is if this is the case.
I agree with gcincotta.
If you are in fact trying to flash from the SD card though, most people have reported that it won't work using an SDHC card. It needs to be a standard (non high-capacity) card.
I did have a card in it..now i took the card out and it goes to tri color in the red i get tita100 and i the white i get serial...thats all it does now
Well i got it to go to usb but now the .exe file for the 2.40 unlocker wont run on x64 systems so i guess im out of luck huh
Did you already run the unlocker? If so, you should be ready to flash a custom ROM. It is normal to be stuck in the bootloader after an unlock. Just flash away.
If the unlock did not go successfully, you will have to try again, making sure to follow directions precisely (on a 32bit system preferably, less headaches). To unlock you must be booted up into Windows Mobile. You can try the exit bootloader program from the PPCGeeks Titan Upgrade forum, or try flashing a stock ROM to get back into WM.
Edit: You can tell if the unlock was successful by looking at the SPL in the bootloader (right under TITA100 MFG). It should now say SPL-2.40.Olipro. If it does not, try the steps above to get back into Windows Mobile.
I did have a card in it..now i took the card out and it goes to tri color in the red i get tita100 and i the white i get serial...thats all it does now
Click to expand...
Click to collapse
You need to be more specific. Everyone's titan says TITA100. What SPL is installed? Post the entire contents of your screen and then we can get somewhere.
I have a new 6800 from Verizon.
software 2.09.605.8
firmware radio 1.30.60
pri ver 1.35.002
pri check 11ab822d
SPL-1.04.000
Do I need to unlock it first ?
Which unlocker do I use ? is it TitanUnlocker.exe
Then the way I read it I need to first flash the Sprint ROM 3.35.651.2
Then what ever rom I want after that.
I was able to udate to 2.52 rom...the 3.04 wasnt working correctly and it would not up date using *228..and there was no sound...i was not using the radio 3.35 because i heard people saying that it was a bad one to use...is there much difference in performace between 2.52 and the 3.04?
So I need to install Sprints 3.35.651.2 rom and not let the sprint customazations run.
Then use the unlocker 2.4
Then use DCD or No2Chem custom rom.
craig540 said:
I have a new 6800 from Verizon.
software 2.09.605.8
firmware radio 1.30.60
pri ver 1.35.002
pri check 11ab822d
SPL-1.04.000
Do I need to unlock it first ?
Which unlocker do I use ? is it TitanUnlocker.exe
Then the way I read it I need to first flash the Sprint ROM 3.35.651.2
Then what ever rom I want after that.
Click to expand...
Click to collapse
You are starting from scratch with an unlocked phone. Before rushing forwards you have some reading to do:
http://wiki.xda-developers.com/index.php?pagename=HTC_Titan
All of your answers are there.
Yes I have read many threads and think that is why I am so confussed. I upgraded from a 6700 which I had flashed to WM6 many times before.
I will follow your linked procedure.
Two questions.
Is my phone being stock and never flashed before locked or unlocked, and do i need to run Olipro 2.40 by executing Hard-SPL-MFG.exe or start with the Sprint Radio (3.35.04)
Also the tutorial says Upon its completion, press the power, camera and reset buttons to force the phone into the bootloader/SPL mode.
What will I see to let me know it is finished loading.
Thanks for your reply.
craig540 said:
Yes I have read many threads and think that is why I am so confussed. I upgraded from a 6700 which I had flashed to WM6 many times before.
I will follow your linked procedure.
Two questions.
Is my phone being stock and never flashed before locked or unlocked, and do i need to run Olipro 2.40 by executing Hard-SPL-MFG.exe or start with the Sprint Radio (3.35.04)
Also the tutorial says Upon its completion, press the power, camera and reset buttons to force the phone into the bootloader/SPL mode.
What will I see to let me know it is finished loading.
Thanks for your reply.
Click to expand...
Click to collapse
1st- update to 2.4 olipro
2nd- update sprint 3.35 rom (stop at the "tap the screen" customization screen) this gives you the radio
3rd- from customization screen start the 3.0.4 rom and flash that rom
Your phone will restart after loading and will boot into wm6.1
4th- Read untill you understand before flashing roms
After 2.4 olipro do I hit reset to let it boot up again or start the sprint rom while its still in bootloader mode
craig540 said:
After 2.4 olipro do I hit reset to let it boot up again or start the sprint rom while its still in bootloader mode
Click to expand...
Click to collapse
Does not matter, if you do it in rom it will force into bootloader anyway.
Ok up and running dcd 3.04
date 2-22-08
radio 3.35.04
I did not let sprint cutomazation run.
Tried to make a call and get message saying verizon can not authenticate and to dial #8899
Should I do that now?
Had to call VZW to get new A-Key
No GPS detected in google maps is there anything I need to do to set it up ?
Try installing VisualGPSce -- it's a good little & free diagnostics program too see GPS satellite reception.
....after seeing that running on COM4 at 4800 baud, then you should see a list of visible satellites. Now, whether or not you get a sufficient lock within the first half hour depend's upon your luck in the draw for a GPS functioning Titan -- GPS hardware-wise, not all are equal.
I currently have a Verizon Wireless fully flashed to cricket XV6800. I decided to know about hacking the Mogul so what I try to do was Look up WMDC 6.1 and apply it to my phone. When i did this the screen stopped at 11%. I took out the battery and tried to turn it on and i get a Red, Green, and Blue color on the start up screen. The words that are on the phone are TITA100 SPL-1.20.Olipro and on the bottom it says USB when connected and Serial when not connected. I looked every where to and figure it out how to get my phone back to the same way. I downloaded so many programs like Titan Unlocker, Titan exitbl, but all these programs do is say my phone is not connected when it is connected. I hear the Sound when the connection for the USB is connected and disconnected. What can i do Will i ever get my phone back to the same state that it once was. I was wondering also that since my phone was flashed that the software will be erased. Is there any way that I can get my Cricket Service. By the way before i did all the hacking what i did was back everything up on the memory card. Is there a way I can restore that through the phone even though i cant access the menu?
I'm going crazy--Thank you for your time to read and for those who can give me some word of advice or some way that my problem can be solved.
Thank you
if u are using xv6800.. i believe u have to install bootloader 2.40 or 2.47.. maybe that might be the problem when installing wm6.1
First, your phone is not bricked.. bricked means broken.. unfixable.. a brick!
You also need to let us know what you software you want to run... DCD 3.2.6?? WMDC 6.1 is Windows Mobile Device Center.. it's not a rom?? So I dont know what you tried to flash.
You need to read the instructions!! Sounds like You upgraded your rom (or tried to) with a non compatible bootloader.. if you dont want to bust your $200 - $500 phone perminently.. you should read the directions twice.. (I read them 4 times, then asked questions before the first time I flashed mine)
When you plug in the device and hear the usb sound.. check device manager.. make sure you see a usb device.. Your OS shoul have installed drivers... Then try the info below.
scrosler said:
1. Download OliPro 2.40 and run it. Ignore the part that asks you to verify the Active Synch connection. Its not needed for anything but a connection confirmation.
2. After running OliPro 2.40 you should be stuck at the three color bootloader screen, Like you are now. If not hold Camera and Power and use stylus to put phone in bootloader. Make Sure it says OLIPRO 2.40 for the version on the bootloader. If not then re-run oliupro and make sure to follow the directions. Especially noting that it asks you to disconnect then reconnect the device.
Click to expand...
Click to collapse
After that you can Flash a Radio, then a rom (I recommend the SD method)
And the versions in my signature.
You can get the SPL 2.40 here:
http://www.lifesnotsogood.com/dcd1182/titan/spl/
You should also read this WIKI
http://wiki.xda-developers.com/index.php?pagename=TitanProblems
If you cant flash SPL 2.40 you will need to flash back to a ROM compatible with SPL 1.20
Read here: http://forum.xda-developers.com/showthread.php?t=392133
I'd try to grab one of thoise older Roms and flash using SD card method.
Then from within Windows Mobile (on your device) Upgrade bootloader to 2.47 (Available from the same link as 2.40 above)
Then flash the radio and rom version I have in my signature.
And dont forget to install carrier cab.
I can't seem to connect my xv6800 to the computer so I can run that program.
I plug it in and the sound comes up and I run the program but it says that it can't copy to device.
loc37 said:
I plug it in and the sound comes up and I run the program but it says that it can't copy to device.
Click to expand...
Click to collapse
Then you need to get a Rom and radio compatible with SPL 1.20.. You'll need a SD card thats Equal to or less than 2GB (NON SDHC)
Check the compatibility here: http://forum.xda-developers.com/showthread.php?t=392133
Read the instructions for flashing this here:
http://wiki.xda-developers.com/index.php?pagename=TITAN_GettingStarted
Check the Flashing with a SD card section.
Process is the same for the radio and the rom.
I cant seem to find an available rom that you need though.. I'll post back when i do.
Unless someone else has a trick for you...
You can also try a another machine that may recognize your phone.
What did you actually try to flash your phone with, and how did you do it.. this is important to help you.
Download DCD 1.6.10 and flash it to your device with the SD card method (Instructions and links in my previous Post) I couldnt find the rom, but I downloaded the kitchen and cooked a rom that should work for you.
Download it from my webserver here:
http://x51.nx-1.com/TITAN/Roms/
Remember you need a proper SD card for this.. if you don't have one, you'll need to buy one.
After flashing this rom.. Assuming your radio is compatible... You should boot into the OS (forget making calls or getting data connection) Just download SPL 2.47 and execute it on your device.. once the SPL is upgraded, Flash the newest Radio, flash the newest rom, run the carrier cab, install aplications..
Let me know if you run into trouble.
okay so what I did was cook up a ROM and then added the Radio 3.37 from alltel on it. I restated the phone and waited the windows mobile 6.1 load screen did not change I moved my keyboard and the sound functioned. I did a restart a hard reset everything I believe it is something with the rom. Any suggestions?
Thanks
loc37 said:
okay so what I did was cook up a ROM and then added the Radio 3.37 from alltel on it. I restated the phone and waited the windows mobile 6.1 load screen did not change I moved my keyboard and the sound functioned. I did a restart a hard reset everything I believe it is something with the rom. Any suggestions?
Thanks
Click to expand...
Click to collapse
Hello loc...try here>>>>http://www.jrstreet.com/flash/burgertime.htm it's a tutorial made by burgertime from howard forums in the cricket section and it's a vid so you can just got through the steps if you get confused..i'm with cricket as well...try here for mms settings that will get your pic/vid messaging working if you have the software installed>>> http://forum.ppcgeeks.com/showthread.php?t=25859 and here is a rom for cricket if you dont wanna try and cook your own just yet>>> http://forum.ppcgeeks.com/showthread.php?t=18836 i love the new dcd 326 which is what i use but in order for me to get my pic/vid messaging working i had to include an oem version of arcsoft when i cooked my rom and vetvito's rom includes everything that you would neeed so you only need to put in the correct seetings plus you need the correct bootloader(olipro 2.40 or nuespl 2.47) and a radio 3.35 or higher...thanks guys and i hope everyone enjoys the weekend and loc i hope that you get it working...by the way loc there is a cricket forum http://howardforums.com/forumdisplay.php?f=336 and a sub forum for pda's that are flashed to cricket
im1badazchick said:
Hello loc...try here>>>>http://www.jrstreet.com/flash/burgertime.htm it's a tutorial made by burgertime from howard forums in the cricket section and it's a vid so you can just got through the steps if you get confused..i'm with cricket as well...try here for mms settings that will get your pic/vid messaging working if you have the software installed>>> http://forum.ppcgeeks.com/showthread.php?t=25859 and here is a rom for cricket if you dont wanna try and cook your own just yet>>> http://forum.ppcgeeks.com/showthread.php?t=18836 i love the new dcd 326 which is what i use but in order for me to get my pic/vid messaging working i had to include an oem version of arcsoft when i cooked my rom and vetvito's rom includes everything that you would neeed so you only need to put in the correct seetings plus you need the correct bootloader(olipro 2.40 or nuespl 2.47) and a radio 3.35 or higher...thanks guys and i hope everyone enjoys the weekend and loc i hope that you get it working...by the way loc there is a cricket forum http://howardforums.com/forumdisplay.php?f=336 and a sub forum for pda's that are flashed to cricket
Click to expand...
Click to collapse
Okay what i have done now is loaded my own personal ROM and then added 3.42.02 Radio to it. The only problem with that is that it keeps restarting and restarting its really weird. Is there any way that i can fix that?
Thank you
loc37 said:
Okay what i have done now is loaded my own personal ROM and then added 3.42.02 Radio to it. The only problem with that is that it keeps restarting and restarting its really weird. Is there any way that i can fix that?
Thank you
Click to expand...
Click to collapse
do you have one of the correct bootloaders? because just flashing to a custom rom and adding a new radio doesn't give you the bootloader that you need so you have to have that too...you can check it by holding down the power button, the camera button and inserting your stylus into the soft reset hole at the bottom of the phone and to get back out of it just do a soft reset but it needs to be be either 2.40 or 2.47 not 1.20 or anything else
im1badazchick said:
do you have one of the correct bootloaders? because just flashing to a custom rom and adding a new radio doesn't give you the bootloader that you need so you have to have that too...you can check it by holding down the power button, the camera button and inserting your stylus into the soft reset hole at the bottom of the phone and to get back out of it just do a soft reset but it needs to be be either 2.40 or 2.47 not 1.20 or anything else
Click to expand...
Click to collapse
When I turn off my phone it says 1.20. What can i do to change it? What software should i Download?
Thank You very Much
loc37 said:
When I turn off my phone it says 1.20. What can i do to change it? What software should i Download?
Thank You very Much
Click to expand...
Click to collapse
......flash a stock pre-gps rom and then upgrade the bootloader to 2.47........then flash whatever you like....
flyers2114 said:
......flash a stock pre-gps rom and then upgrade the bootloader to 2.47........then flash whatever you like....
Click to expand...
Click to collapse
Okay I solved that problem but now when I click on the settings option on the menu my phone freezes. What can be the cause of that? Did I cook the ROM wrong?
Thanks
loc37 said:
Okay I solved that problem but now when I click on the settings option on the menu my phone freezes. What can be the cause of that? Did I cook the ROM wrong?
Thanks
Click to expand...
Click to collapse
Usually that means you have the wrong build of MSVC installed use build 19209...
loc37 said:
Okay I solved that problem but now when I click on the settings option on the menu my phone freezes. What can be the cause of that? Did I cook the ROM wrong?
Thanks
Click to expand...
Click to collapse
if you now have the correct bootloader and radio...try flashing with a pre-cooked rom like dcd 326 or the rom from the links that i gave you...the popular one was the black pill and there is one that's specifically for cricket
do I just google that build number or is there a specific program I should download?
Thanks
loc37 said:
do I just google that build number or is there a specific program I should download?
Thanks
Click to expand...
Click to collapse
LOL..no if you lookk about five post up you will see DCD 326 and as for the other from vetvito it was in one of the links that i first posted for you
loc37 said:
When I turn off my phone it says 1.20. What can i do to change it? What software should i Download?
Thank You very Much
Click to expand...
Click to collapse
Did you read any of my posts...
Hrm.. could have sworn I addressed this already.
x51 said:
You can get the SPL 2.40 here:
http://www.lifesnotsogood.com/dcd1182/titan/spl/
Click to expand...
Click to collapse
x51 said:
Then from within Windows Mobile (on your device) Upgrade bootloader to 2.47 (Available from the same link as 2.40 above)
Then flash the radio and rom version I have in my signature.
Click to expand...
Click to collapse
I included links, and all the information you would need.. (Like the Rom/Radio/SPL compatibility list) yet you didn't read it.
I spent time finding those links, downloading a rom.. cooking it for you, and uploading it to my webserver so you can download it.
x51 said:
Download DCD 1.6.10 and flash it to your device with the SD card method (Instructions and links in my previous Post) I couldnt find the rom, but I downloaded the kitchen and cooked a rom that should work for you.
Download it from my webserver here:
http://x51.nx-1.com/TITAN/Roms/
Remember you need a proper SD card for this.. if you don't have one, you'll need to buy one.
After flashing this rom.. Assuming your radio is compatible... You should boot into the OS (forget making calls or getting data connection) Just download SPL 2.47 and execute it on your device.. once the SPL is upgraded, Flash the newest Radio, flash the newest rom, run the carrier cab, install aplications..
Let me know if you run into trouble.
Click to expand...
Click to collapse
I also explained that once you boot into windows with that rom, you need to upgrade your bootloader to 2.47 (with instructions) and then your radio, and then rom.
The path was simple..
Flash dcd 1.6.10 (compatible with SPL 1.20) so the phone will boot
Upgrade SPL (bootloader to 2.47)
Flash new radio (3.47.50)
Flash new Rom (3.2.6)
Run carrier cab.
If you are still asking about where to get the (SPL) bootloader.. I guess I cant help you....
i have a Telus & HTC P4000 tytn.
running
(from boot loader)boot screen)
spl 2.07.0000
cpld-9
(boot screen)
r 3.42.040
d 3.54
(device information)
rom 3.54.661.1
radio 3.42.40
and i want to update my rom to
DCD titan 3.26 with a radio of titian radio rom 3.42.50 and nuespltitan100-2.47-pack
i THINK i have all the files i need
and i THINK i know which order to do them in.
i install the
nuespltitan100-2.47-pack
spl (boot loader) upgrade first
then run the radio rom next ( from a micro sd card right?)
then the dcd titan 3.26 rom last (once again from a micro sd card??)
i am a bit confused and could really use a step by step guide for each upgrade
as im not real sure what could go wrong.
one last inportant point.. on the titan wiki it says to
" Always keep a record of your phone's ESN, MSID, Security, EPST, and M. IP settings in case a flash reprograms your phone."
and i have not found the security or epst m and ip settings (found the others)
and it says
"if it is 1.04, 1.06, or 2.07 then you must unlock your phone and upgrade to 2.40 or 2.47. Olipro 1.20 is not necessary at all when using newer ROMs/Radios."
how do i unlock the phone for the upgrade to 2.47?
( i just cant find any unlock other than http://forum.xda-developers.com/showthread.php?t=332381&highlight=unlock but i think that any spl update is considered an unlock..)
please help me help myself not brick my phone.
nutz
look here
http://forum.ppcgeeks.com/showthread.php?t=33857
Hi, a general xv6800 workflow question
I'm wanting to upgrade my verizon xv6800 to wm6.5 with manila. I plan on using: leo.rs.wm65.wwe and radio 4.49.25.17.
I have mr2 (3.57.605.2 and rad 3.37.748 , spc 2.07
I just want confirmation that I have this right: usb connect
1. run hard-spl-mfg.exe , put the phone in bootleg mode with pwr.cam.reset
2. run the customruu with the radio file, put the phone in bootleg mode again
3. run the customruu with the rom file. allow spontaneous reboot..
4. run *228 to program
Is that it? do I need to run "verizon carrier 20081030.cab" too?
thanks
The current radio you have now is ok, but you need to upgrade your bootloader first, so that is correct. Unlocked bootloader (olipro 2.40). You can't just use a ROM/radio from the LEO. You need one for the Titan. More than likely, you will have to install Manila from cabs. Whitealien has posted those in the Dev/Hacking subforum. Do a search, I'm sure someone has a step-by-step going from MR2 back to a custom ROM. And unless you use a specific Verizon ROM, yes, you will need to run the carrier cab.
Dude that rom is not for your phone. If you flash it you will brick your phone.