Related
I've just ordered an MDA Vario and it's going to take a little time to reach me (I'm not currently in the UK). Before it gets here I'm trying to work out which screen protector to buy. Has anyone tried the Invisible Shield protector? The material looks superb and I've read load of good things about their performance on iPods.
My current PDA is a Tungsten T3 and I have a Martin Fields screen protector on it. (MF protector for Wizard here).
I love the MF but am really interested in hearing experiences with the IS if anyone on these forums has tried it.
Yeah i want one too but was wondering, do they leave any marks when you peel them off afterwards? From the glue and stuff?
Quality screen protectors like Martin Fields and the IS should leave nothing behind after they're removed.
I think brando screen protector is not bad too. Im currently using it.
I have change 2 screen protector since I got my wizard.
- Expansys, Cant fit in properly. Bubble occur after stick in.
i've tried 3 different screen protectors, then i used pocketpctechs AG shield and i'm not gonna try anything else. It's perfect, reusable, no glue is used and installation is pretty simple. also it comes with screen cleaners and all that. highly recommended
For me brando's would be ok. I usually have the store person do the application since I can't do it on my own [I messed up 2 protectors when I tried doing it at home]. I'd say choose one that isn't adhesive but static that way no residue is left on the screen when you remove it. also most of them are washable/reusable... if you find a scratch on the side you use most often [i.e. the area along the SIP] just have it removed and re-installed reversed [not the face but the top and bottom].
The Brando ultraclear is OK. If you prefer a non-glossy one, the Brando regular is perfect (you will lose a bit of brightness).
I like www.boxwave.com 's version
They have a anti-glare, and a regular one, they are washable you can remove them and wash them under soap and water and reapply, they come with cloth cleaner, and a little scraper thing that helps get the bubbles out.
Here's a super cheap solution, and it works GREAT for me.
I went to Staples and bought a package of baseball card protector pages that are designed to fit into a 3-ring binder. The size of each card holder is just slightly larger than the screen on the MDA.
What I did was take a straight edge and X-Acto knife and cut a small piece of plastic that is a couple millimeters larger than the screen on each side. I simply tuck the plastic I've trimmed under the lip between the device and screen, and it holds in place just fine.
No adhesive, no mess, easy as pie, and the entire package of plastic sleeves was less than 3 bucks. It will surely last longer than the life of the device.
- Justin
Got my second Brando regular protector (first one wasn't returned when my magician was replaced). Fits perfect, very scratch-resistant & the anti-glare is very useful while navigating in the car.
Cheers, M
fone_fanatic said:
i've tried 3 different screen protectors, then i used pocketpctechs AG shield and i'm not gonna try anything else. It's perfect, reusable, no glue is used and installation is pretty simple. also it comes with screen cleaners and all that. highly recommended
Click to expand...
Click to collapse
Same here.. I have used BoxWave, wich are also very good, but WriteShields from pocketpctechs are great.
I also had an "InvivibleShield" on my 8125 for a couple minutes. I installed it and saw that it was not plum on, so I went to take it off and reinstall.. When I removed it I thought I was going to pull my screen up with the protector. Stay away from those things... I then tested those claims they make on the website, about being indestructible. Pens had no trouble getting through, and scissors went through like soft butter.
$.02
I bought a boxwave and was not happy with the glare free one. I have used them on my Treos and liked them, but the one that came for my wizard sucked. It really blurred the screen and made it look like a prism. Maybe it was defective, but I ended up buying another one from javoedge and I am quite happy with it.
just my $.02
greg
I also got an anti-glare from boxware, it does have issues however I emailed them about it and they are getting a new one that doesn't have the issues and they should have it in about a week. To make it even better they created a gift order for the new one for me.
I've tried a number of the commercial screen protectors in the past and wasn't happy with any of them. Of course, there is the ridiculous cost for a little piece of plastic.
The best solution I have found is to use clear vinyl sheeting that you can find at any fabric store, typically for a couple of dollars US per yard. Just cut to fit your screen, clean your screen, wash your hands and vinyl rectangle with liquid hand soap, shake off as much water as possible (but not all), and attach and smooth out bubbles.
Benefits:
- Minimal screen image degradation as compared to many commercial screen protectors
- No adhesives to gunk up the screen
- Lasts 6 months or so
- Easy to replace
- Costs about a nickle per cover
I also have the pocketpctechs write shield anti-glare.
Comes in a nice kit, can't tell its there when the screen is on.
http://www.pocketpctechs.com/main.asp?unit=Cingular_8125-559&area=home
I bought mine from www.nushield.com, but I haven´t been able to apply the first one to my screen.
I´ve used them on my Handspring Visor Edge and on my Himalaya with very good results, but on the Wizard, I just can´t get it installed. Will keep you posted!
Stefan out
Brando screen protector, Boxwave and Martin Fields are my favorites!
I've heard a lot about this Brando, but it is a bit too expensive for me for a piece of plastic. I think they are selling for GBP7+ in eBay. I wonder, is it so good? I've been looking for those 'card' type screen protector that is ultra easy to apply and bubble free because the protector itself feels like a card. Imagine, since the protector is like a card, it is impossible to get bubble under it. Anyone know where in the net I can get one card type for UK??
BTW, I've bought the 'Sensifilm' protector from eBay. It said many things, but of the two thing, antiglare and antiscractch is 100% bluff. Mine still give me glare and it has been scratched like mad with my stylus. Either the HTC is very bad in designing a stylus, or the screen protector is terribly weak. I think the weak protector is a more likely answer.
30$ for a screen protector. That is so silly. I got a protector for my psp for 6$ and it works great. Geez, pocketpctechs is a rip.
Cant i get some from a local store instead?
I can highly recommend Brando UltraClear too! Easy to attach, not visible when attached carefully, no reduction of brightness - display looks like without one (for those who do not like the reflection of the display: buy the Brando classic).
Regards
Carsten
Just to let you know that I bought the Brando Screen Protector for the Diamond2 from Inkino. They even installed it for me which is a bonus. The screen protect is absolutely amazing and is a good as any that I have seen. Do not scrimp on cheap nasty ones that come in multiples in a pack. You only ever need one good one. The Ikino guy showed me a Treo 650 which had a Brando Screen protecter that he had installed when the Treo 650 came out (was I born then ) and it was in a very impressive state. If you are going to install it yourself then they do recommend doing it very slowly and cleaning the screen before-hand is crucial. Common sense I know, but you would be surprised how easy it is to get dust under the protector.
got mines today. 2 pcs, both from Brando. one is the Ultra Clear version.
i've applied the "normal" one for now and i must say it's really cool!
putting it on went pretty much smooth. in the bathroom, where i guess there's less dust, i've cleaned first the screen with a special lotion. then waited until it dried up, after that applied the Brando screen protector as shown in the "instructions".
went OK, only had to start again 2-3 times, then found the right position. went over it with a credit-card while smoothing it out on the D2's screen. it sits very good, no air bubbles and really just a few very small dust pieces at the border of the protector - does not disturb.
so, yes, the Brando screen protectors are really the thing!
now i want only the textured back plate and then i'm really happy!
PS: didn't find the screen-protectors on the romanian market, so had to order them from speedshop.hu (hungary), but eveything went very smooth! in 2 days after the payment
Could you post pictures for me? I'm looking for a screen protector too. Does it cover the whole black part, or just the 3.2 inch screen part?
it covers the display + the black border around. it's actually identical in size with the one delivered in the stock package, the difference in the aspect being the "U" shape around the front camera (the original one is a circle).
I don't get it, mine came with a screen protector.
I think it is quite a good protector,
why are you intersetd in th ebrando protector, didn't yours came with a protector as well ?
well0549 said:
I don't get it, mine came with a screen protector.
I think it is quite a good protector,
why are you intersetd in th ebrando protector, didn't yours came with a protector as well ?
Click to expand...
Click to collapse
yeah, i know. the problem is that i didn't pay enough attention when putting on the screen protector that came in the box and i messed it up (got dust and airbubbles under the protector), so after i've tried to get it clean, i messed it up so bad that it got useless.
this is why i ordered 2 brando's (speedshop.hu has 2 versions) - put on one that is not the "ultra clear" version and now i am happy with it.
When applying the standard screen protector that comes wit the phone, how do you get the screen free from greasy finger prints? If I wipe it with a cloth I just smear it out
Laban said:
When applying the standard screen protector that comes wit the phone, how do you get the screen free from greasy finger prints? If I wipe it with a cloth I just smear it out
Click to expand...
Click to collapse
Use CD/DVD cleaner
I use those: 3M Vikuiti DQC160
http://www.3m-displayschutz.de/dqc160
Scratchproof, crystal clear and very easy to get on and off.
Is a screen protector really important? I used mine, but the dust freaked me out. Can't place it without any dust...
So I removed mine, and now not using anything. Just bought a case.
What do you think?
loadstone007 said:
Is a screen protector really important? I used mine, but the dust freaked me out. Can't place it without any dust...
So I removed mine, and now not using anything. Just bought a case.
What do you think?
Click to expand...
Click to collapse
You should put one, if it is not too late: once your screen is scratched (and it will get scratched, very fast if u use the stylus), you will have to buy a new screen cover (I think it include the digitizer), which will be much more expensive, or live with scratches which will blemish your screen, which are especially bad with TD2: the very high pixel density will cause moiré pattern (rainbow effect) around the scratch and I find that very annoying...
It is not so hard to install, mine was my first attempt at installing a screen protection, and it went flawlessly: just be careful, do not hurry, do not put your fingers on the screen (once cleaned) nor on the sticky face of the protector, and work in a clean, dust free, well lit room. Dust free is hard, but an excellent trick i did found here was to use your bathroom, after a hot shower (keep the water runnnig a long time, and take a shower yourself ) It will ensure YOU are dustfree ;-), but also, more important, water condensation will remove almost all particles in suspension, and you will get very clean air. BTW, better to wear minimal clothes after your shower: clothe fibers is the most common dust/particles....
If you work in such a place, the only difficult thing is to get the screen protector perfectly aligned. I started on the top, got the grid and camera holes aligned, tried to cover the screen from top to bottom, and restarted as soon as I saw the slightest misalignment without letting the screen protector out of my hand (else it is very difficult to repick - that was the only trouble I had after I was too enthusiatic and let it go while there was still a small misalignment.
If you keep calm, and have good hand coordination, 2 or 3 attempts and you will have an invisible screen protector ;-) Oh yes, and start with a clean screen (I cleaned mine with distilled water and a soft microfiber glass cleaning tissue...worked very well....)
Thanks, I'll have to buy one then.
BTW, does a screen protector affect the sensitivity of the screen? Do you have to press slightly harder on the screen to get it to recognize your finger?
loadstone007 said:
Thanks, I'll have to buy one then.
BTW, does a screen protector affect the sensitivity of the screen? Do you have to press slightly harder on the screen to get it to recognize your finger?
Click to expand...
Click to collapse
slightly, yes....on the other hand, it is more slippy, although not enough for my taste when using fingers, but it is an improvement compared to the bare screen. Before I installed the screen protector, it was much too grippy for confortable finger sweep motions imho (clean screen, after a while finger grease act as a lubricant ;-) ).
All in all, weighting the slight decrease in sensitivity against the friction reduction...I prefer my screen with the screen protection, even taking out the protection factor
There's this Zagg product for the TD2, which is invisible. Not really sure about this... I might just get the regular screen protector, and use a silicone case.
I would recommend placing the bottom edge of the screen protector up against the bottom buttons to align it. I managed to get it perfect first time.
I find the supplied screen protector picks up finger prints even worse than the bare screen. Are the after market ones any better?
My reseller did the protective screen installation for me. Did a good job. Did you guys get the free pouch also? I am not sure if the pouch came with the unit or if it was a free gift as a promotion.
What's the difference between different brands of protectors and the original HTC ones? I bought last week branded HTC protectors made exclusively for Diamond 2, their HTC part nr is SP P240, they fit fantastically well.. Are they worse than brands mentioned earlier in the thread?
cassper1 said:
What's the difference between different brands of protectors and the original HTC ones? I bought last week branded HTC protectors made exclusively for Diamond 2, their HTC part nr is SP P240, they fit fantastically well.. Are they worse than brands mentioned earlier in the thread?
Click to expand...
Click to collapse
Those look the same as the orignal, that came with the device.
cassper1 said:
What's the difference between different brands of protectors and the original HTC ones? I bought last week branded HTC protectors made exclusively for Diamond 2, their HTC part nr is SP P240, they fit fantastically well.. Are they worse than brands mentioned earlier in the thread?
Click to expand...
Click to collapse
May be they have some particular features such as "antiscratch" or "washable screeing protector"!
I have also recently bought original one SP P240 and very glad with it!
And never mind, original parts are not worse than other brands!
Has anybody every used this brand of screen protector's before? They just sent me an email saying that they have in stock screen protectors specific for the T-mobile TP2 and I am debating whether or not to buy them.
http://www.boxwave.com/products/cle...screen-protector-t-mobile-touch-pro2_3668.htm
I originally had a Martin Fields on my Touch Cruise that I loved, but they don't make the screen protectors for the T-mobile TP2
I used one on my MDA (prior to getting the TP2). I loved it (make sure to get the crystal clear, not the non-glare, if they have a choice). 3 years and looks like new, nice slick surface for using the stylus, extremely durable. But I don't have experience with any others (except the one that came in the TP2 box which I also like a lot).
Thanks for sharing!
I´ll go for one of those
The crystal clear is one of the best I've used before!
I have used the Anti-Glare version for my 6700 and 6800/Mogul and love it. I used my phone in my car alot so the Anti-Glare is a must. It also finger print resistant, I'm using the screen protector that came with the phone now and the finger print smudges are just driving me nuts! I've order one and is waiting for shipment notice.
the Anti-Glare version is a semi reigid piece of plastic that make it very easy to apply, similar to the included protector, I hate those soft floppy protector that's next to impossible to put on correctly
bitslizer said:
I have used the Anti-Glare version for my 6700 and 6800/Mogul and love it. I used my phone in my car alot so the Anti-Glare is a must. It also finger print resistant, I'm using the screen protector that came with the phone now and the finger print smudges are just driving me nuts! I've order one and is waiting for shipment notice.
the Anti-Glare version is a semi reigid piece of plastic that make it very easy to apply, similar to the included protector, I hate those soft floppy protector that's next to impossible to put on correctly
Click to expand...
Click to collapse
is the anti glare version kinda gritty to the touch ive never used one?
osrix25 said:
is the anti glare version kinda gritty to the touch ive never used one?
Click to expand...
Click to collapse
Was wondering this as well. I ordered a Clear Touch while my co-worker opted for the anti-glare. I'll try to do a side by side comparison when they arrive.
bitslizer said:
I have used the Anti-Glare version for my 6700 and 6800/Mogul and love it. I used my phone in my car alot so the Anti-Glare is a must. It also finger print resistant, I'm using the screen protector that came with the phone now and the finger print smudges are just driving me nuts! I've order one and is waiting for shipment notice.
the Anti-Glare version is a semi reigid piece of plastic that make it very easy to apply, similar to the included protector, I hate those soft floppy protector that's next to impossible to put on correctly
Click to expand...
Click to collapse
Speaking of anti-glare... im using one on my Iphone 3G..got it back from Manila,Philippines on my last holiday, some chinese brand screen that i thought will be just a piece of crap screen protector.
to my surprise it was 98% perfectly fit on my iphone...and it was a great anti-glare screen protector. my wife likes it now she wants 1 for the htc touch pro2. ive seen some on ebay i might order it this week.
for those who's using one... where did you guys buys the anti-glare screen protector?? -thanks
Arcarsenal said:
Was wondering this as well. I ordered a Clear Touch while my co-worker opted for the anti-glare. I'll try to do a side by side comparison when they arrive.
Click to expand...
Click to collapse
Nice one thanks
I've raved about it before many times, just search my posts on here and PPC geeks, but the BoxWave AntiGlare is the best screen protector for any device hands down period end of story etc!
osrix25 said:
is the anti glare version kinda gritty to the touch ive never used one?
Click to expand...
Click to collapse
I wouldn't say gritty, but its definitely neither frictionless or sticky and doesn't impede your fingers or stylus movement in anyway... its got a matted texture, and I really like using my stylus with that texture! more of a paper feel, offering just the right amount of feedback and friction.
You do lose a tiny bit of clarity compare to the Crystal version, but for the anti-glare, anti-finger print benefit, I love it!
finger prints and face oil on the stock screen protector have been driving me nuts!
I'm supposed to get it today but heading out of town for a wedding this weekend so may not have a chance to report or upload pix until monday
Thanks for the report, i can imagine a paper texture! i think i may order one. cheers
What do you all think of these dedicated screen protectors, as compared to using the screen cover provided by invisibleSHIELD or Bodyguardz? Are the ones you all mentioned, or from "BoxWave" better because they are made specifically for the purpose of screen protection? Or are the I.S. or Bodyguardz ones comparable, since they are built to offer all around protection?
venomshot629 said:
What do you all think of these dedicated screen protectors, as compared to using the screen cover provided by invisibleSHIELD or Bodyguardz? Are the ones you all mentioned, or from "BoxWave" better because they are made specifically for the purpose of screen protection? Or are the I.S. or Bodyguardz ones comparable, since they are built to offer all around protection?
Click to expand...
Click to collapse
Personally, the 3M crowd is better because then you don't have to worry about the screen protector getting scratched.
I had purchased a Boxwave Anti-Glare before and it worked decently, but the amount of glare it reduced was negated by the amount of brightness that needed to be increased.
Boxwave, in my opinion, works if you have a case protecting it. But trying doing this with a Boxwave.
osrix25 said:
is the anti glare version kinda gritty to the touch ive never used one?
Click to expand...
Click to collapse
NOT gritty.
I have used Boxwave screen protectors for years and have NEVER been disappointed. Excellent longlasting product that your stylus simply glides across; I have settled on the Anti-Glare. One post says that Boxwave isn't TOTALLY scratch-free like some other 'full-body' clear protectors. Correct. However, personally I do not like the idea of spraying a liquid all over my device in the application process. 'Full-body' protectors are applied just like installing tinting on you car's windows.
Suggested application procedure.
Before beginning I have two clean microfiber cloths; one is included. Clean your phone's screen well; preferably w/one of those microfiber cloths. Close windows in bathroom, run shower on hot a bit & turn off. Moisture will pull all the dust outta the air and drag it to the floor. Vent heat (u don't want it to be uncomfortable in there).
Now that all the floating dust is negated, clean your screen again w/the the other microfiber cloth and apply protector. It is helpul to have some tape applied to a corner or two of the protector. Utilizing the tape, lift and reapply as needed using the supplied squeegee or a credit card to clear out bubbles; you may need to lift protector and use the microfiber cloth to pick up some lint/debris to ensure a clean install.
You should have a lint- and bubble-free application if you were careful.
Good luck from Lincoln!
I just got the new Boxwave ClearTouch Crystal screen protector for my T-Mobile TP2: http://www.boxwave.com/products/cle...screen-protector-t-mobile-touch-pro2_3668.htm
I had previously had a Boxwave on my MDA. That has lasted 3 years with no signs of wear, and I was extremely pleased with the fit and feel, so was hoping to do the same for my TP2. I researched all of the competition and read many forum posts on the subject. My main criteria were:
1) quality
2) exact fit
3) feel with finger and stylus
4) longevity
Price was less of a concern as I am hoping I will only ever need just the one for my TP2 (if my previous experience with the MDA is anything to go by), and so the lower priced ones, or the ones that came with 2 or 3 in the pack, were not a strong selling point for me.
The other main one I narrowed it down to was the Bodyguardz, and I probably would have got that if the Boxwave hadn't been coming out soon.
Boxwave advertised pre-orders were available for October 9th shipping. I searched high and low but couldn't google a single coupon code, so ended up paying full price of $12.95 + $2.50 shipping. They shipped a day or so late, and because of the long holiday weekend it arrived a little later than it probably could have, but as far as shipping, packaging, tracking go, I give Boxwave an A-
I had actually been perfectly happy with the screen protector supplied by HTC, but as others have noted, in some cases it may have been a tiny bit too large, causing bubbles along one edge. I think I had put it on pretty perfectly, but then, in my obsessive need for perfection, had pulled it off a little and proceeded to snip away too much screen in an attempt to get it to fit just right, making for an install that now looked a bit messy and with a bit of glass exposed along a jaggedy edge of protector. But the Boxwave fit perfectly, and very easily, just using the instructions on the package (i.e. I just put it on dry, no sprays or water). I did steam up the kitchen a bit first to try to remove dust, and obsessively cleaned the screen for 10 minutes before attempting the install. On my first attempt I started from the short top edge and that caused a problem as the protector was now not aligned correctly down the right side, so I pulled it up and laid it down again from the long left edge, making for a much easier alignment. However, when I had pulled up the protector from the first attempt, I had used the little plastic card to ease up the protector; I think I caused some very minor damage to the protector at the point of contact, as there is now a tiny minor bubble there that is probably caused by a kink I may have made in the plastic. I'll work on smoothing that out, but it's off the screen and very minor (however, let that be a warning to others to be extremely careful if you need to lift the plastic off. I tried using sticky tape but the suction was too strong for it to get a grip, and using something like a pin seemed like potential to damage the screen.) For fit and finish and ease of installation, I give Boxwave an A (and me a B- )
The surface of the 'Crystal' clear screen (I don't know how different the 'anti-glare' version would be) is very slick. In fact looking at it, touching it, sliding my finger across it, and using the stylus on it, seems exactly the same as the actual glass screen on the phone. I went into notepad and made a new note so I could doodle with the stylus. With almost no pressure I could draw lines about 90% of the time, the rest it would skip a little. But with just a tiny amount of pressure, about what you would probably use in normal use, it was at 100% coverage, with practically no drag feeling, just a nice slippery but not too slippery feel. Sliding with my finger is fantastic, I can now scroll through the programs screen much easier than I did with the original HTC. For sensitivity and surface texture I give it an A+
Overall I give Boxwave and the Cleartouch an A+. I am reminded of that old Memorex commercial 'Is it real, or is it Memorex', because looking at the phone right now, I can't tell it has a screen protector, it looks just like glass. I am sure there are others out there as good, although I doubt there are any much better. There are certainly other quality ones that are much cheaper, $15 seems like a crazy price to pay for a piece of plastic. Others come with 2 or 3 protectors, and many have coupon codes you can find on Google. And others, like Bodyguardz, come with a solution for complete protection, not just the screen. Of course time will tell, but based on my A+ experience with Boxwave on my MDA, I really am quite confident of the same longevity and performance on the TP2.
One happy customer.
I've used Boxwave screen protectors and accessories for the past several years, and I can honestly say I've been always 100% pleased. I've used both the antiglare and clear protectors, and prefer the clear ones - but it's all a matter or preference, but overall a good purchase.
First, Boxwave screen protectors have always been my standard. I've tried a couple other types (mostly what's been included with devices or what I can find in retail stores) and won't likely be messing around with that again. I personally prefer the "crystal" models over the anti-glare because I didn't like the affect of the anti-glare pattern on the display. It kind of gave it a fuzzy moire pattern. The crystal basically looks like those super glossy laptop screens - looks great in low/medium lighting but could be a problem in certain direct light situations. Still, the trade-off is worth it to me.
Second, does anyone know if any of the existing TP2 protectors will fit the AT&T Tilt 2? The European/UK model looks not ideal because of the front camera hole and the T-mobile version appears to have a slightly different button layout on the bottom. Both the Verizon and Sprint models look right to me on the web page, but Boxwave support just says to submit a request and wait. I would prefer to get a protector on mine ASAP but am reluctant to order if the fit isn't right.
Daniel
bought one for my Sprint Touch Pro 2, it applied perfectly and not noticeable at all. I prefer it way over the invisibleshield I had on my Vogue which was too rubbery and reflective.
Am I correct to think the Boxwave screen protector for the Sprint TP2, Verizon TP2, and the ATT Tilt 2 are the exact same thing? I have been looking at pictures and the screen shapes look identical. The only different ones are the T-mobile and the front facing camera versions.
Thanks!
Hey everyone,
looking for a great screen protector that helps with the glare issue and viewing angles. I'm not expecting wonders but anything to help. Hate the fact I see reflection on screen sometimes. Any info would be great. Thanks
Gemni69 said:
Hey everyone,
looking for a great screen protector that helps with the glare issue and viewing angles. I'm not expecting wonders but anything to help. Hate the fact I see reflection on screen sometimes. Any info would be great. Thanks
Click to expand...
Click to collapse
How about checking the Skinomi thread in this very first page of this section ?
I just orderded some screen protectors from ebay hong kong. 11.99 for 3. ill let you know how they work.
Good Screen Protector
Ordered one from Amazon made by Aurum(do a search). It came quickly and I am very happy with it, wished I waited a few days, they have a deal going on with it.
It says its made from Japanese PET, in my experience it is better than those "military" strength ones like Zagg etc(bad evo 4g experience). This one has a dry application and protected on both top and bottom by covers (a protector for the protector). Ships from the US.
I have the Skinomi. I'm happy with it, but it does not appear to help with glare or screen angles (though, honestly, I only used it for a few minutes before installing the protector).
dj_justice said:
I just orderded some screen protectors from ebay hong kong. 11.99 for 3. ill let you know how they work.
Click to expand...
Click to collapse
which ones did you get?
-J
Go with the Skinomi one. It's cheap (relatively if you consider lifetime free replacement) and if you don't botch the installation it looks fantastic. And... you don't have to wait three weeks for something to come from China.
Don't get me wrong, I buy stuff from China sometimes but only when I can't get it here or if it's a lot more money to get it from here.
Anyone have recommendations for screen protectors? Looking for helping with anti glare and no finger prints on it. Any info would be great. Thank for all the feedback so far.
Traderny said:
Ordered one from Amazon made by Aurum(do a search). It came quickly and I am very happy with it, wished I waited a few days, they have a deal going on with it.
It says its made from Japanese PET, in my experience it is better than those "military" strength ones like Zagg etc(bad evo 4g experience). This one has a dry application and protected on both top and bottom by covers (a protector for the protector). Ships from the US.
Click to expand...
Click to collapse
I just ordered one of the Aurums too. I have a "matte" type screen protector on my iphone and I really like it so I hope the aurum one is similar. I will update once it arrives.
emersonlp said:
I just ordered one of the Aurums too. I have a "matte" type screen protector on my iphone and I really like it so I hope the aurum one is similar. I will update once it arrives.
Click to expand...
Click to collapse
Do you mean this one ? according to the user image its not custom made (no holes for the camer/sensors) not sure if it would even cover the bezel + the screen.
sjmoreno said:
Go with the Skinomi one. It's cheap (relatively if you consider lifetime free replacement) and if you don't botch the installation it looks fantastic. And... you don't have to wait three weeks for something to come from China.
Don't get me wrong, I buy stuff from China sometimes but only when I can't get it here or if it's a lot more money to get it from here.
Click to expand...
Click to collapse
The Skinomi one requires a WET application, that then has to dry, do you really want to spray some liquid on your new g-tab? I tried this on my Evo installation was a pain but then my fingers got stuck scrolling, so I learned my lesson and stick to the PET material which has a silicone coating for smooth movement
Aurum Screen Protector
You are right, I have the Aurum one from Amazon on my G-tablet, and there are no holes, but I do not see a difference in camera performance. The protector covers bezel to bezel. I've used the camera with and without the protector, all I know is that it is as grainy before as it was after the Aurum screen protector. I do not use the camera(I really do not need anyone getting scared looking at me) so it's fine by me, it the smoothness of movement that matters.
just my $0.02, but why not use the one by Zagg....?..
http://www.zagg.com/invisibleshield...es-screen-protectors-covers-skins-shields.php
Traderny said:
You are right, I have the Aurum one from Amazon on my G-tablet, and there are no holes, but I do not see a difference in camera performance. The protector covers bezel to bezel. I've used the camera with and without the protector, all I know is that it is as grainy before as it was after the Aurum screen protector. I do not use the camera(I really do not need anyone getting scared looking at me) so it's fine by me, it the smoothness of movement that matters.
Click to expand...
Click to collapse
Thanks for the info, Traderny. Would you say that the Aurum screen protector allows for smoother gliding movements than the unprotected GTab screen? I'm hoping to find something that provides a nice swipe feel. Too often my fingers would "stick" to the naked screen or (less so, but still) the Skinomi protector.
My .2 cents
Traderny said:
The Skinomi one requires a WET application, that then has to dry, do you really want to spray some liquid on your new g-tab? I tried this on my Evo installation was a pain but then my fingers got stuck scrolling, so I learned my lesson and stick to the PET material which has a silicone coating for smooth movement
Click to expand...
Click to collapse
Wet application screen protectors have been around for a while and it has been shown to not be an issue if you follow the directions on installation. There are thousands of people that have used wet installation screen protectors here in the gTab forums that have reported no residual issues with the gTab during/after application.
Also, you don't spray liquid on the gTab, rather you're supposed to spray the liquid on both sides of the screen protector before application and dab up the excess liquid as you work it to the edges with the provided plastic card.
I've used both PET and this style of screen protectors on devices before and I prefer this over the PET as I have found the PET style protectors to be too shiny for my tastes.
Among the most helpful reviews for the PET protector on Amazon there are these comments:
1.) Good product, but a pain to put on. Just the slightest piece of dust will cause an air bubble.
2.) According to the packaging, this item is "Finger print free" and "Bubble free application". I experienced both. I would NEVER purchase this product again or recommend it.
Just goes to show you that people will find something to complain about no matter what the product is.
Protectors Protect
My experience with screen protectors on cell phones is that they are only good to protect the screen from damage. All of them will show fingerprints, smudges, grease and oil. This is esp. true with a touch screen. it's like wearing glasses you got to clean them alot. So save time money and headache by putting a microfiber cloth in the bag with your Gtab.
I went with the Exim anti-glare screen protectors, but did have to wait for shipping from China. I bought a complete skinomi skin set, and promptly botched the wet application of the screen protector, but since I wanted the anti-glare it just meant a week wait for the Chinese Air Mail which I had already ordered.
Overall I like the Exim, it was easy to install without any bubbles, though you might want to trim the corners a bit as its a very tight fit. I ended up cutting them off after applying it because I had the screen on perfectly without a single dust mote making a raised area. I don't mind a poorly cut corner, but do wish I had just done a quick trimming beforehand as I wasn't perfectly centered.
2 for $12.99... Was worth the wait.
Hey Naieve,
does it really help with the anti glare issue? Also does it have any issues with the touch screen interface? Is the screen protector to thick that it doesnt detect your finger movement on the screen? Any help on the finger print issues haha?
It helps some with the glare, definitely diffuses the light, but it looks more like a compromise in between a clear protector and some of the very heavy anti-glare screen protectors I've seen. I like it because of this actually. As to issues with the touch screen, I spent some time googling before buying, and while I forget where I read it the fact is there is no difference while using this protector. Even a light touch still works just fine. I wonder if that is the reason this AG protector diffuses less light, as I have heard of some AG protectors being too thick and screwing up touch. It does still show fingeprints, but its not that bad and is easy to clean. Definitely less noticeable than just the screen itself.
aasoror said:
Do you mean this one ? according to the user image its not custom made (no holes for the camer/sensors) not sure if it would even cover the bezel + the screen.
Click to expand...
Click to collapse
I said I would update once my Aurum arrived. Like others have mentioned, there is no cutout for the camera or sensor - I don't know what effect that has nor do I really care. I never use the camera anyway.
The protector itself fits perfectly on the screen - it is so perfect that I had trouble aligning it properly and i would get halfway done installing it and notice it was running off the side of the screen slightly.
It took a few minutes to install because I did want it to be perfect. Now that it is installed I am really happy with it. My fingers slide better across the screen and there are far less fingerprints. I am happy with my purchase.
Have had the TF300 for about a week and just cannot stand the fingerprints and worries about scratches. I'm used to Gorilla Glass and this is driving me nuts. I've been researching screen protectors quite a bit and cannot seem to get a consensus on a certain brand. I know the selection for the TF300 right now is slim, but given what you've used on earlier devices, what is a good brand to go with?
I have it in a case (Caseen Designo), but would like an extra layer of protection.
I've had good experiences with SGP's Steinheil screen protectors. I've used both the clear ones as well as the matte glare reduction/smudge resistant models and have been happy with both. The usual reduction in clarity is in the matte protector, but the cut was very precise and it lasted me a year before i took it off because i missed the crisp picture of the IPS panel, the protector was still pristine.
I just keep a microfiber and a small credit card style sprayer with 50/50 alcohol and water mix in the bag that i keep the tablet in, and its been alright so far, if you keep it in the dock most of the time you shouldn't have to worry about it being scratched unless you drop it or something, which i have yet to do since i also have a skinomi techskin on the back so its nice and grippy.
SGP doesn't make a protector for the TF300 yet, but i'd keep an eye on it, they make some solid products.
screen size is same as prime so protectors made for the prime should work.
johnjohnjohnson said:
screen size is same as prime so protectors made for the prime should work.
Click to expand...
Click to collapse
You may want to check camera and light sensor placement before you put a prime screen protector on. They may be the same but it never hurts to check
Nothing else will work with the TF300 unfortunately.
I've been researching like crazy and think I've narrowed it down to:
Zagg
Stenheil
XtremeGuard
Those seem to get the best reviews. I'm really looking for:
same feeling as naked screen
optimal clarity
mitigates fingerprints
If you've never felt a zagg's wet apply film before i suggest you find someone who's got something similar to it and try it first, i see one of the criteria is feel close to naked screen, zagg and other wet apply soft skins usually feel grippy when you first install it, and gradually over time will wear out and feel smoother. In general there are the wet apply films which feel a bit like vinyl except its clear, or the dry apply protectors which are harder pieces of plastic, those will feel closer but nothing will be quite like a naked screen.
Is there big difference on screen sensitive between glossy and matte screen protector? or just you see difference of screen quality...
Thanks
I almost wonder if I might just be better off with a naked screen. I have my TF300 in a Caseen leather case and am always very careful when it's in use. The only thing I'd like to mitigate is the fingerprints.
Wait for a ClearCoat screen protector....i have tried every other brand and there is NOTHING like them. Super thin, no spongey feeling or orange peel....
I bought the xtremeguard one on ebay for 8.99 It fits great. The one I got isn't anti-glare though. One thing that kind bothers me, since I have never used a screen protection before, is that my fingers don't glide as easily as in the glass, it shows a bit of resistance. But I guess I just got to get used to that. I have not seen a reduction in screen sensitivity as of yet, but my dagi stylus kinda sucks now with the screen protector T_T since its plastic on plastic the resistance is really bad.
I like my skinomi. it takes forever to apply since it's wet application and if you're OCD about bubbles/lint like me. But once you've got it on there perfect and wait for it to dry and clear up it's not bad at all +lifetime guarantee.
I've always liked wet applications over the adhesive/static stuff just because they last a long time, and I havent noticed the yellowing people have talked about on any of my devices, I agree about the stylus issue, though (jot pro)
+1 for skinomi...
I used to swear by Zagg ...
Skinomi has only a slight orange peel effect and is generally smother except I agree it is still a nogo for the Jot pro as it doesn't let the plastic disk glide
after a while the Zagg invisible skins would start to keep my finger from sliding properly...
Skinomi skins do not have this issue and they dont show finger smudges very much
I want to try the Zagg HD skins as they are supposed to be glass smooth but they seem to only be out for iProducts and the kindle fire.....
rj7766 said:
+1 for skinomi...
I used to swear by Zagg ...
Skinomi has only a slight orange peel effect and is generally smother except I agree it is still a nogo for the Jot pro as it doesn't let the plastic disk glide
after a while the Zagg invisible skins would start to keep my finger from sliding properly...
Skinomi skins do not have this issue and they dont show finger smudges very much
I want to try the Zagg HD skins as they are supposed to be glass smooth but they seem to only be out for iProducts and the kindle fire.....
Click to expand...
Click to collapse
It would be cool if the Zagg HD worked with plastic disk styluses
aelunyu said:
I like my skinomi. it takes forever to apply since it's wet application and if you're OCD about bubbles/lint like me. But once you've got it on there perfect and wait for it to dry and clear up it's not bad at all +lifetime guarantee.
I've always liked wet applications over the adhesive/static stuff just because they last a long time, and I havent noticed the yellowing people have talked about on any of my devices, I agree about the stylus issue, though (jot pro)
Click to expand...
Click to collapse
the lifetime warrenty requires you to pay for shipping and handling by paying for the shipping and they also ask that you put your cc# on a paper and send it in. kinda risky there.
mrevankyle said:
You may want to check camera and light sensor placement before you put a prime screen protector on. They may be the same but it never hurts to check
Click to expand...
Click to collapse
just got the bestskinsever protector for the prime and size is the same and cut out for camera is in the right spot. should be good to go on other protectors made for prime.
jgaf said:
I bought the xtremeguard one on ebay for 8.99 It fits great. The one I got isn't anti-glare though. One thing that kind bothers me, since I have never used a screen protection before, is that my fingers don't glide as easily as in the glass, it shows a bit of resistance. But I guess I just got to get used to that. I have not seen a reduction in screen sensitivity as of yet, but my dagi stylus kinda sucks now with the screen protector T_T since its plastic on plastic the resistance is really bad.
Click to expand...
Click to collapse
This will pass eventually from wear, on my zune hd i used to have an invisible shield which is a similiar kind of wet apply soft protector, and eventually the center part wore down enough to where it was like a hard plastic protector.
You bring up a good point though that i forgot to mention, i've used matte hard protectors, clear hard protectors, and soft wet apply films and my adonit jot still works best on a naked screen, though the matte hard protector had more of a paper resistance to it and the clear and naked both were much smoother.
Szpaner: the touchscreen sensitivity for me was largely the same between a clear hard protector and matte hard protector, i wasn't able to glide as well with the wet apply film so i wasn't able to gauge properly how sensitive it was compared to the other two.
mfratella: a light coat of rain-x on the naked screen helps make it much easier to wipe clean, i can breathe on it once or twice and the condensation is good enough to clear the whole screen. Even with the matte hard protectors which are supposed to be designed to be anti-fingerprint, they will still show up eventually from the oils in your finger, those spots will end up being a little more transparent so you'd have to wipe anyway, though in my experience the matte ones are the easiest to wipe, i used to just use my sleeve and give it a once over and it was all clean.
szpaner6 said:
Is there big difference on screen sensitive between glossy and matte screen protector? or just you see difference of screen quality...
Thanks
Click to expand...
Click to collapse
When I've used a matte screen protector, I didn't notice any difference in screen sensitivity. The biggest difference is in the clarity of the screen. On a phone, I can deal with the graininess that a matte screen protector brings with it. But on a tablet with a large screen, something that I'm going to use for long periods of reading, it's far too distracting for me. Personally, I'd rather work around glare now and then along with wiping off finger prints in exchange for a clearer screen.
Screen protectors compatible with dock?
The Armorsuit people replayed on an email I sent them asking if their screen protector was compatible with the keyboard for the TF300.. it appears it is not. They answered me just to be careful... so I was planing on cuting it. these screen protector is actually pretty good, and I think that I wont even notice the protector end-line at the bottom of the screen after a while. Do you know if cutting it actually works?
I just installed the Skinomi on mine. Took about 5 minutes and it's perfect. Just gotta makes sure you soak the hell out of the screen (you won't damage it) and both sides of the protector plus your hands so that you don't leave finger prints on the adheasive. If you have enough of the solution on everything it should kinda float on the surface of the tablet. You can just very easily slide it around until it is center and then start pushing the water out to make it stick. I didn't have one bubble on mine when completed.
The Zagg is now avail at best buy . No issues with the stylus either. Now all i need is a case im comfortable with.