hi all,
Im just trying to use the australian three network rom on my vario 2 but after it goes into bootloader mode it fails to reconect and comes up with "error 260"
upgrade error. has anyone any ideas how to get round this. could it be a bootloader problem, 1.01 at the moment.
TTFN
Jay
Please read the wiki and the mrvanx guide at the bottom of my signature before hand if you want to avoid bricking your device if this is your first upgrade.
responderman said:
hi all,
Im just trying to use the australian three network rom on my vario 2 but after it goes into bootloader mode it fails to reconect and comes up with "error 260"
upgrade error. has anyone any ideas how to get round this. could it be a bootloader problem, 1.01 at the moment.
TTFN
Jay
Click to expand...
Click to collapse
All Sorted Now
Its all working fine now, just needed a different rom loader instead.
Ta!
Hello friends,
I believe I made something totally wrong while downgrading from AP3.0 to T.Mob WM6....
I started with Olipros unlocker until step 2 - then my device refused to reboot when step 2 was finished...
I can enter bootloader mode without any problems - but don't know how to proceed.
Who can give me some advice ?
Thanks in advance.
Dieter
OK - found now that I have to run the "romupdateutility".
Where can I find that ?
Dieter
And finally got it running.....
I have now learned:
1. to use the "search" function in detail
2. what a RUU is
3. and I don't need to run the unlocker again to downgrade the ROM
Dieter
I can´t supercid my niki 100. i follow the instructions but nothing. it stops in steep 7 and nothing more apears. please anyone can calculate the code to sim unlock my niki? please contact me. i send the emai. thanks a lot. my email. [email protected]
Did you tryed to press enter when supercid windows appears?
I don´t know how, but after 10 times doing the same thing it worked. installed a full rom and do the all procedure again and it worked. thanks a lot. solved and niki unlocked. thanks
your problem was the USB reconnecting ...
Halo,
excuse me for the bad English!
After the SSPL 1,16 I forgot the USPL or HardSPL in the hurry.
And I have directly try the new ROM to load. I get since then
only still error 262. If I it with the new original HTC WM 6.1
get I try the error 294 invalid Dealer ID.
What can I there still do?
With MTTY I have access to the XDA. Whom I an instruction send
come an answer of the XDA. I do not get ahead however with MTTY.
It is correct that one with MTTY ROM also on the equipment to load can?
For the syntax I need however help.
Thanks
Franz
guys
most of us cant install hspl to our beloved htc titan while others enjoy 7.8
we are stuck
i have talk to cotulla and he needs us to send him a usb log to see whats going on
her are my conversations with him
Originally Posted by Cotulla
Hello,
Sorry, for the long answer.
I am looked to that problem already, but did not really find issue
Maybe you should try different PC as test . . .
USB inside SPL is a bit laggy in the Omega/Ttian.
Best regards,
-Cotulla
Hello,
I don't have Titan 2. And other DFT members too.
But it can be another kind of the problem - I don't have TEST/MFG roms for Titan2 seems.
Without them it can be hard to do HSPL.
About AT&T Titan. . . my Titan is AT&T.
Can you make a usb log during installation once more?
Best regards,
-Cotulla
Hello,
Thanks for help.
I will recommend to use progam USBLyser: it has 30 days trial version it should be enough.
Note you should start logging before starting HSPL program.
You may need to increase capture buffer in the settings.
Save log as HTML at the end.
Best regards,
-Cotulla
guys lets get this to cotulla so we can finally be able to install 7.8 in our titan
also he doesnt have a titan 2 to be able to get hspl to the titan 2 we need to donate one to him
i will offer 50 dollars
i hope you guys can help me out
i got this from pzman89
I downloaded a usb logging tool, not sure if this is the info he is looking for or not, but I attached 2 screenshots where there seems to be an error (that happen towards the end of the HSPL installation process). There is more to the log file, however it is approx. 14 MB and in its own format.
link the usb tool . i am about to install hspl on a titan in 2 days ... i will give a log ..
got it ...
sathara said:
link the usb tool . i am about to install hspl on a titan in 2 days ... i will give a log ..
got it ...
Click to expand...
Click to collapse
Hello,
Thanks for help.
I will recommend to use progam USBLyser: it has 30 days trial version it should be enough.
Note you should start logging before starting HSPL program.
You may need to increase capture buffer in the settings.
Save log as HTML at the end.
Best regards,
-Cotulla
i havent use this method yet dont know a way to find it
can you help us out here
i am also doing this for first time ... i hspl one titan before 4 months every time it fail and i got it when i partitioned my sdcard from 2 gb to 900mb . i will let you know after i am done . did you hspl ed ?
sathara said:
i am also doing this for first time ... i hspl one titan before 4 months every time it fail and i got it when i partitioned my sdcard from 2 gb to 900mb . i will let you know after i am done . did you hspl ed ?
Click to expand...
Click to collapse
hi i have done 5 titan
same result
stuck with no hspl
i have seen this many times
i want to have hspl to be able to enjoy 7.8
we need help from everyperson that can help
htc titan 2 is also a very nice device and cotulla needs a device to hspl
lets make it happend guys
tell me where you stuck , i also stucked many times , after a trying for 7 hours i done it ... di you debrand it ..did you see a f400 in bootloader ...?
sathara said:
tell me where you stuck , i also stucked many times , after a trying for 7 hours i done it ... di you debrand it ..did you see a f400 in bootloader ...?
Click to expand...
Click to collapse
yes
i did all the steps as follows
debrand it using gold card
rebooted a couple of times
installed 2.05 spl using goldcard method
rebooted a couple of times
install hspl with no success
i did this to like 5 titan
also
sh4d0w86 is stuck in mfg also
and several others
pzman89 awesome work
Hi All,
Here is a link to my USB Log file, created through USBLyser: http://dl.dropbox.com/u/29307361/hsplUSBLog.html. It is approx 17MB. Appreciate you all taking the time to look at it.
Hello,
Thank you for the log.
But it looks very nice. Like nothing bad happens.
Can you after HSPL installation reboot enter SPL mode and connect phone to MTTY and enter "task 37 debug" and then send output to me?
Maybe it needs more time at the end . . . I will try to make a test version.
Best regards,
-Cotulla
Dude there is no procedure to HSPL HTC TITAN II, so please write correctly about that.
kristijan said:
Dude there is no procedure to HSPL HTC TITAN II, so please write correctly about that.
Click to expand...
Click to collapse
yes we know
thats why we need to send a titan 2 to cotulla
he needs it to build the hspl
pzman89
So I downloaded the program called MTTY (1.4.2), but I honestly do not know how to use it. The first screen that pops up asks for me to choose a com port. I am unsure which com port to choose from. Also, the instructions found with the MTTY program say there should be an option for USB, but I don't see an option for that.
That being said, there were 3 com ports (COM1, COM2 and COM3). Com3 allowed me to go to the next screen however, when I tried to type something in the box that popped up, nothing happened.
can someone help pzman89????????
some times a ilove xda
Originally Posted by pzman89
So will the titan 2 help with the issue us AT&T Titan 1 users are having?
not really but i would like to help the owners of titan 2 also, now that we have the attention of cotulla and some folks out there might help us out too
if i dont get help with the titan 2 ill donate it from my own pocket
Nice, yeah, I'll help out any way I can. Don't really have enough funds now, but I might be able to donate at least $10 if things really start going. I might even donate $10 just for Cotulla taking his time to look at this, even if it doesn't work.
elmanortega said:
pzman89
So I downloaded the program called MTTY (1.4.2), but I honestly do not know how to use it. The first screen that pops up asks for me to choose a com port. I am unsure which com port to choose from. Also, the instructions found with the MTTY program say there should be an option for USB, but I don't see an option for that.
That being said, there were 3 com ports (COM1, COM2 and COM3). Com3 allowed me to go to the next screen however, when I tried to type something in the box that popped up, nothing happened.
can someone help pzman89????????
Click to expand...
Click to collapse
This version of MTTY requires old usb sync drivers. Search for "Eugenia drivers" (x64) on xda, or probably some other drivers. Also you must disable USB connection in WMDC.
and yes, USB is what you actually must see.
amazing work by pzman89
Hey,
I can't quite remember if I actually sent you my log file for the task 37 that cotulla requested. If not, here it is again: http://dl.dropbox.com/u/29307361/Task37DebugLog.txt
While I know you guys are trying to get this info for dev-related reasons, I think this more properly belongs in the Titan General forum.
guys
general is the graveyard of threads
we will continue this
privately
consider this closed