So I haven't upgraded a Titan in while, but a friend wanted me to upgrade his. It's a US Cellular and I put DCD Reloaded on it and forgot it didn't include the radio. so here's what's going on.
As I said before I put DCDs 4 Reloaded.
I had loaded Nuespl 2.47, BUT now THr bootloader is saying it's back too SPL 1.07.0000.
The RADIO is 1.64.00.
THe ROM is 3.2.6.
It stuck on the HTC load screen. I have tried to load the 3.42.50 Radio via SD, but it will say loading and nothing happens. The SD is formatted FAT32 with 1024 allocation. Being US Cellular I don't have access to the stock ROM. Soooo, in short what do I do from here?
Did you name the radio TITAIMG.nbh for flashing with micro sd? What you could do is re-flash the bootloader (use olipro 2.40). When that is done flash a Official Sprint ROM GPS v 3.35 and up. Then flash the titan reloaded or whatever GPS enabled rom you are flashing.
Hope this helps, I would guide you through all the steps but I am exhausted. You can find all that stuff by searching here or ppcgeeks. The olipro 2.40 is on my share site. Sprint ROMS you can get some from htc and some from searching forums.
RyanMogul6800 said:
Did you name the radio TITAIMG.nbh for flashing with micro sd? What you could do is re-flash the bootloader (use olipro 2.40).
Click to expand...
Click to collapse
I have been trying that. OK so with the SD flash which I have never done before this time. Do I put the Unlocker and the Radio on the card at the same time or do I do them one at a time? Thanks in advance.
One at a time. It is not possible to have two files named exactly a like on a card at the same time.
drewcam888 said:
One at a time. It is not possible to have two files named exactly a like on a card at the same time.
Click to expand...
Click to collapse
Ok but the unlocker and the Radio DO have different names. Though I have been trying to added them one at a time, however on the bootloader screen it will say "loading" for either half a second or will freeze on "loading". The end result is still nothing changing, same SPL and same Radio. Im following ever thing to the T form the wiki, but it doesn't seem to work as they say it will.
The unlocker need to be done first.
drewcam888 said:
The unlocker need to be done first.
Click to expand...
Click to collapse
I do this and it doesn't "update" anything I formated the SD in FAT32 w/ 1024 allocation, put the unzipped unlocker onthe card boot the phone in to the boolaoder mode it will load for like a half second and go back to the bootlaoder but the SPL doesn't update it stays stock 1.07.0000. I don't get what I'm missing?
I really don't know what unlocker you are using. But I haven't heard of an unlocker that can be run in bootloader. For example 2.47 can be opened in WM. I thought you might have found the .nbh for a unlocker but it sounds like you are putting a zip file on the card which won't work.
drewcam888 said:
I really don't know what unlocker you are using. But I haven't heard of an unlocker that can be run in bootloader. For example 2.47 can be opened in WM. I thought you might have found the .nbh for a unlocker but it sounds like you are putting a zip file on the card which won't work.
Click to expand...
Click to collapse
I'm following these instructions.
Upgrade via the microSD (<=2GB) card
(Thanks to No2Chem - donate here)
IMPORTANT: The nueROM web site indicates that nueSPL version 2.47 is designed for the HTC Titan with GPS enabled only (ROM versions 3.xx or higher). Any other device will be permanently and irreversibly damaged by this version of boot loader. (Please use your OEM's latest signed radio ROM to get to this version or higher before trying to install.)
Copy the nueSPL-2.47.exe file from the nueSPL-2.47 package onto your device. (A PDF file with instructions is also included in the package.)
Using File Explorer, run the nueSPL-2.47 application from where you copied it, read the license agreement, then press CONTINUE if you accept.
Read the prerequisite screen carefully. If it indicates that you do not have a FAT32 formatted partition, you will need to format your microSD card by pressing FORMAT (WARNING: this will erase any data on the microSD card).
If you meet all of the requirements, press CONTINUE. It will take approximately 10 seconds for nueSPL to copy the TITAIMG.nbh ROM to your microSD card, then nueSPL will automatically reboot your phone in order to load the ROM.
After the reboot, you will be prompted to press the POWER button to begin updating the new SPL boot loader. Once the installation is complete, the phone will reboot.
Allow your phone to fully reboot. Once your phone is rebooted, open File Explorer and inspect to see if your storage card contains the file TITAIMG.nbh. If it is present, delete it before continuing.
Press and hold the CAMERA and POWER buttons at the same time and hold down the RESET button (with stylus) until you enter a multi-color bootloader screen. You should see a screen that says SPL-2.47No2Chem Titan SPL EVT. If you see this text, your SPL has been sucessfully updated. If you do not, press the RESET button and start over from step 1.
I don't get where I'm going wrong?
Are you able to boot to windows to even run the .exe?
if you are unable to boot the phone bc the rom and radio do not match and you say that the spl is stock you won't be able to change it to unlock without being able to boot into the phone to flash the proper spl onto it to ublock it. Here is what your choices are.
Go to HTC's website http://www.htc.com/us/SupportDownload.aspx?p_id=75&cat=2&dl_id=73 scroll to the bottom of this page select the sprint tv win mobile 6.1 upgrade and then a us server then click download.
Let the file download.
Run the file and let it get to the welcome to the rom update utility screen. Minimize the window do not close it.
Go to my computer and do a search for RUU_signed.nbh you should see one come up in the list if not you need to find your computers temp folder inside of your user profile. For example mine is C:\Users\Gator\AppData\Local\Temp (windows 7 vista and xp might be named a little different) inside that folder in the same search again.
Once you find that file rename it and to TITAIMG.nbh and load it onto your sd card. Put the card in the phone and put it in the boot loader mode Power + Camera held down + push the reset button in. The phone should load the rom and you will see the press the power button to begin the update.
This should work because the rom is signed.
Upon the first boot of the phone calibrate the screen yada yada. When u see the device will automatically customize in 3 seconds soft reset the phone.
Take the storage card out and put the nue spl 2.47 file on it. Run that to unlock the phone if it does not work it just means u need to load .net 3.5 on the phone b4 running the utility. http://rapidshare.de/files/39254419/NETCFv35.wm.armv4i.cab.html
Once you are unlocked and good to go u can now download whatever rom ie the dcd reloaded rom. Take the file zip or rar open it copy out the RUU_signed.nbh file rename to TITAIMG.nbh load it on sd card and do the bootloader process it will flash and u are good to go.
That would be the best way to do it i think as trying from the computer always leads to complications with the operating system or the user or the ppc giving you update errors.
You can try if you cannot locate the RUU_signed.nbh (that gets placed in a temp folder). To put the phone in the bootloader with it hooked up to the pc you will see it say usb @ the bottom instead of serial. Load the sprint udate utility that you downloaded and go through all the checks and nexts till it tries to update the phone. It will not show the current rom info but it should be able to flash the phone as all the utility does is put it in bootloader anyway b4 flashing.
Good Luck.
gator2k83 said:
Go to HTC's website http://www.htc.com/us/SupportDownload.aspx?p_id=75&cat=2&dl_id=73 scroll to the bottom of this page select the sprint tv win mobile 6.1 upgrade and then a us server then click download.
Click to expand...
Click to collapse
It's giving me an "Invalid Vendor" error. THe phone is a US Cellular model.
Also is there any way to go about this via usb from the booloader screen? The bootloader is stock 1.07.000.
Thank you all for your help, I've done this all before RIGHT but now that I have a Vogue I'm a bit spoiled but the ROM/Radio combos.
You cannot flash that new sprint rom and radio with that bootloader. Simple. I told you put olipro 2.40 on there via its own RUU. Its a exe how simple? Then you can simply from there flash a gps radio using RUU or MicroSD, Then flash a custom GPS enabled ROM using RUU or MicroSD. Each file needs done one at a time obviously. For RUU flashing the .nbh file should be named or renamed RUU_signed.nbh, for using MicroSD the .nbh file should be named or renamed to TITAIMG.nbh
And here is a PM I sent lacrizzle
RyanMogul6800 said:
Make sure your computer has htc drivers on it first. Then plug the phone into the computer and make sure it connects to active sync. Then run the OliPro 2.40 unlocked bootloader. Then install official sprint ROM with gps Radio, Then flash custom ROM, then change spc code to all zeros. Its not that difficult.
Click to expand...
Click to collapse
You could also try extracting the .nbh from the Olipro 2.40 exe. Some exe's have extractable contents and some are not. Use winrar, or 7zip. Olipro.exe is extactable and you will fine the .nbh in there. Then rename that to TITAIMG.nbh and flash using microsd method. This way seems to work when people are really really having problems. Then complete the other steps to get back to custom ROM.
There is no need for him to install a Sprint rom that wouldn't help him any. Unzip and add put the attached 2.47 Nue unlocker .nbh on your sd card and put the phone in bootloader. After the new bootloader is installed just update your radio by sd card and you are good to go.
Last Night---->
drewcam888 said:
I really don't know what unlocker you are using. But I haven't heard of an unlocker that can be run in bootloader. For example 2.47 can be opened in WM. I thought you might have found the .nbh for a unlocker but it sounds like you are putting a zip file on the card which won't work.
Click to expand...
Click to collapse
This Morning---->
drewcam888 said:
There is no need for him to install a Sprint rom that wouldn't help him any. Unzip and add put the attached 2.47 Nue unlocker .nbh on your sd card and put the phone in bootloader. After the new bootloader is installed just update your radio by sd card and you are good to go.
Click to expand...
Click to collapse
Any reason why It took you four posts to realize a solution for the guy? Now all of a sudden you know of a unlocker that can be ran via micro sd in bootloader. Now all of a sudden you know the stock sprint ROM will not help him any.
Well seems like you may have been doing a little reading, and re-emphasizing since then.
We are all eager to help and are providing different solutions until his problem is fixed. I have posted and PMed the user several solutions including updating the bootloader first then the radio, then the custom ROM. Hopefully with all of our answers and knowledge the user will get his problem sorted out.
It is the same unlocker as before I just took the time to extract the .nbh from the .exe of the unlocker.
Whats the chances you found out that you could extract the .nbh from my post above? Then just applied it to the no2chem 2.47 unlocker?
RyanMogul6800 said:
You could also try extracting the .nbh from the Olipro 2.40 exe. Some exe's have extractable contents and some are not. Use winrar, or 7zip. Olipro.exe is extactable and you will find the .nbh in there. Then rename that to TITAIMG.nbh and flash using microsd method. This way seems to work when people are really really having problems. Then complete the other steps to get back to custom ROM..
Click to expand...
Click to collapse
Good work though, maybe flashing the 2.47 unlocker via micro sd will work out for the user. I always use olipro but I guess thats personal preferrence.
To bad that wasn't the case since this .exe is a wm executable so I wasn't following your instructions. Sorry about your luck
Very true, I didnt know that it was a WM exe. But like I already said I may have turned you on to the idea of extracting the .nbh from there wether you can use traditional methods or not. I also have never used that (from what I hear and read) buggy no2chem 2.47 unlocker.
But like I am saying you didn't turn me onto anything.
Related
It is possible - I've just done it. I'm away from home and I've been using my Hermes (with WM5 AKU 3.3) to get my iBook online all week. Finally WM6 has appeared but I'm stuck with no Windows PC to perform the upgrade...but XDA-Developers gave me all I needed to do it. Here's the outline of how to do it (you'll need to figure out some finer details yourself, but I will help where possible if you get stuck).
1) You need just the .nbh file from the WM6 package of your choice. Unfortunately they are built into Windows installers. I downloaded XDA-Live and extracted the .nbh file using Virtual PC.
2)
i) Backup your storage card.
ii) Format your storage card. (I used a program called "Storage Tools" for this).
ii) Rename the WM6 .nbh file to HERMIMG.nbh and copy it to the root of the empty storage card.
3) Get Des' SSPL program from this link:
http://forum.xda-developers.com/attachment.php?attachmentid=34184&d=1171162518
4) Put the SSPL executable on your phone and run it. Cross your fingers. The phone should enter the bootloader and offer to upgrade the OS using the image it finds on the storage card.
And that's it. Once I'd figured this out, the method is straighforward. The part that has taken me all day is getting the image file extracted from a Windows world and onto a blank storage card using only a Mac and the phone itself (and no other internet connection)!
Hope this is useful to someone else.
Edit: typo.
Great! This method is much safe than other methods that depends on USB because you don't have to worry about someone unplug the USB cable, or if the PC will hang during the flashing process.
Maybe the only thing to check is to ensure that the device to have enough battery for flashing
BTW, how long will it takes for this SD upgrade method?
Brilliant!
Very ingenious solution! I'm not ready to flash yet, I want to see some bugs worked out of the WM6, but when I'm ready will probably try it your way just to see how it works!
Ben
Awesome, I'm using Vista, and I don't want to install XP just to flash Thank you.
Will this work with the Universal? I'm getting Vista soon and I want to be able to reflash if I need to.
Thanks in advance.
ahlok_hk said:
BTW, how long will it takes for this SD upgrade method?
Click to expand...
Click to collapse
I didn't time it but I'd guess it only took about 5 minutes.
You CAN flash on Vista using regular ROM updaters (the .EXEs). That's how I upgraded to AKU 3.3 recently (I don't have an XP machine either).
You do it by connecting in bootloader mode so that "HTC USB Sync" appears in Vista's Device Manager. Then you replace that driver with the one from 2004 (I got mine off the CD that came with the phone). Then the ROM updater works
Now is there a way to exec the sspl.exe on boot? So that some of the bricked users can jump start into bootloader and flash any rom.
unfortunately not... sspl is a wince EXE.
Radio ROMS's
Does anyone know if the Radio only ROM's can be flashed by this method also. If you can do you name the .nbh file the same or use a different name.
You can flash any NBH file, radio os or whatever. But not extracted radio roms in NBF, only in NBH. The file must be named HERMIMG.nbh.
pof said:
You can flash any NBH file, radio os or whatever. But not extracted radio roms in NBF, only in NBH. The file must be named HERMIMG.nbh.
Click to expand...
Click to collapse
interesting... does that include unsigned updates??
walshieau said:
interesting... does that include unsigned updates??
Click to expand...
Click to collapse
Yes, but only with SSPL.... not with the real SPL on device.
pof said:
Yes, but only with SSPL.... not with the real SPL on device.
Click to expand...
Click to collapse
ok now back to the drawing board then... do you know whether the SPL can be forced into Service mode via the RomUpgradeUT.exe file... have been doing some digging around in the DLL's and EXE and found some info about a 'Service' mode....
walshieau said:
do you know whether the SPL can be forced into Service mode via the RomUpgradeUT.exe file... have been doing some digging around in the DLL's and EXE and found some info about a 'Service' mode....
Click to expand...
Click to collapse
Not sure if I understand your question.... the so called "service mode" is what we call "booltoader mode" or "tri-color screen".... just the same.
On normal RUU, the bootloader mode is invoked by EnterBootloader.exe, on custom RUU EnterBootloader.exe file has been replaced with SSPL-HERM.exe.
pof said:
Not sure if I understand your question.... the so called "service mode" is what we call "booltoader mode" or "tri-color screen".... just the same.
On normal RUU, the bootloader mode is invoked by EnterBootloader.exe, on custom RUU EnterBootloader.exe file has been replaced with SSPL-HERM.exe.
Click to expand...
Click to collapse
yes i know that BootLoader is a type of Service mode... i was talking about a different procedure... it looks like a command from the RomUpgradeUT file to signal the bootloader to just to flash the ROM and not check the RUU sig's, model type etc....
walshieau said:
i was talking about a different procedure... it looks like a command from the RomUpgradeUT file to signal the bootloader to just to flash the ROM and not check the RUU sig's, model type etc....
Click to expand...
Click to collapse
That's not possible with the normal IPL+SPL on device, load them on IDA Pro and you'll see what it exactly does, its small enough to follow all the disassembled code with the samsung manual in hand.
so......if i want to flash both radio and wm6,
all i have to do .. is to extract the nbh file from .exe using winrar or something and rename it, put it into a formated sd card.. and run the sspl thing and do the same for wm6 ?
yes hellokittyr, that's right.
Hi pof,
have you tried to digg into the radio ROM as well? Probably with the right manual in hand one could seperate the RBL from the rest and create a 1.35.00.11 radio ROM with RBL 0107.
I currently have Radio 4.42.30 installed.. I also had 3.42.02 prior too but did not see any significant change in GPS Locking.. Finally I found a set up that best suits me.. Try this..
Install Titan Radio 3.42.30..
http://forum.xda-developers.com/showthread.php?t=403280
If you have problem flashing from SD card then follow these steps:
1. Download NueSPL2.47[Newest Release]
2. Back up your files on you mSD card to your PC
3. Extrac and place NueSPL2.7.exe on your SD card
4. Run it.. this program will format your SD card to enable flashing from SD [if its not already formatted CORRECTLY]
5. NueSPL will place the BOOTLOADER file onto your SD card and name TITAIMG.nbh... Let it run.. it will now update your Hard SPL to version 2.47
6. it will automatically put your phone into Bootloader mode
7. The gray screen will pop up indicating that its flashing a BOOTLOADER
8. Press the power button when prompt to start flashing after it finishes.. allow NueSPL2.47 to clean up..
9. your phone will restart..
10. Place RADIO named TITAIMG.nbh onto your SD card
11. put your phon into bootloader mode by pressing POWER+CAMERA+RESET buttons
12. Bootloader should now recognize TITAIMG.nbh as CDMA not Bootloader..
LET IT RUN AND YOU'RE DONE!
NueSPL2.47 found here... Thank No2Chem for his work please...
http://forum.ppcgeeks.com/showthread.php?t=30561
Appy this Titan GPS FIX...
http://forum.xda-developers.com/showthread.php?t=400975
An updated version of QPST Program is found in Post #178
Intall AstroGPS if you have TomTom7 or iguidance.. I use the TomTom launcher.. Huge difference..
http://forum.xda-developers.com/showthread.php?t=364199
This is My set up.. I didnt notice a big changes before I applied the GPS FIX.. Now my GPS locks within 5 seconds.. Good luck..
b16daddy said:
I currently have Radio 4.42.30 installed.. I also had 3.42.02 prior too but did not see any significant change in GPS Locking.. Finally I found a set up that best suits me.. Try this..
Install Titan Radio 3.42.30..
http://forum.xda-developers.com/showthread.php?t=403280
If you have problem flashing from SD card then follow these steps:
1. Download NueSPL2.47[Newest Release]
2. Back up your files on you mSD card to your PC
3. Extrac and place NueSPL2.7.exe on your SD card
4. Run it.. this program will format your SD card to enable flashing from SD [if its not already formatted CORRECTLY]
5. NueSPL will place the BOOTLOADER file onto your SD card and name TITAIMG.nbh... Let it run.. it will now update your Hard SPL to version 2.47
6. it will automatically put your phone into Bootloader mode
7. The gray screen will pop up indicating that its flashing a BOOTLOADER
8. Press the power button when prompt to start flashing after it finishes.. allow NueSPL2.47 to clean up..
9. your phone will restart..
10. Place RADIO named TITAIMG.nbh onto your SD card
11. put your phon into bootloader mode by pressing POWER+CAMERA+RESET buttons
12. Bootloader should now recognize TITAIMG.nbh as CDMA not Bootloader..
LET IT RUN AND YOU'RE DONE!
NueSPL2.47 found here... Thank No2Chem for his work please...
http://forum.ppcgeeks.com/showthread.php?t=30561
Appy this Titan GPS FIX...
http://forum.xda-developers.com/showthread.php?t=400975
An updated version of QPST Program is found in Post #178
Intall AstroGPS if you have TomTom7 or iguidance.. I use the TomTom launcher.. Huge difference..
http://forum.xda-developers.com/showthread.php?t=364199
This is My set up.. I didnt notice a big changes before I applied the GPS FIX.. Now my GPS locks within 5 seconds.. Good luck..
Click to expand...
Click to collapse
Thanks for taking the time to write this!
I've been meaning to check out NueSPL but haven't gotten the chance yet...what's the advantage of having it versus Olipro 2.40?
kmartburrito said:
Thanks for taking the time to write this!
I've been meaning to check out NueSPL but haven't gotten the chance yet...what's the advantage of having it versus Olipro 2.40?
Click to expand...
Click to collapse
also, what are the advantages of the updated QPST?
the original QPST was a beta version and the one in the later post is the final release.. for example.. for the first release.. after you added a Comm Port and want to remove it.. it wont be removed until you restart QPST.. where in the new version.. it removes right away.. they're both the same but the later one is more stable i guess..
i found that getting an instant lock is as simple as:
installing the radio
installing the rom
installing carrier cab
soft reset
reinstall radio
dial *228 2
dial *22899
instant locks every time
Any chance of seeing this for Sprint? I've got Radio 3.42.30 and stock ROM 3.56.351.0. I have QuickGPS installed updated and I'm still taking 2-3 minutes for a lock in Google Maps.
yrsmart said:
Any chance of seeing this for Sprint? I've got Radio 3.42.30 and stock ROM 3.56.351.0. I have QuickGPS installed updated and I'm still taking 2-3 minutes for a lock in Google Maps.
Click to expand...
Click to collapse
Update PRI to 2.03 or 2.04
Awesome!
My GPS hasn't worked in months.
That SPL upgraded FIXED my ****ing mSD card upgrading problem.
Ok so first is first.. I did read the wiki and I have searched.. even posted in a rom 3.42.50 post (i think that was it) but no replies...
so in that other post I followed the instructions.... I used a 512mb micro sd and a 64mb micro sd....
jambrose said:
FROM THE TITAN WIKI:
Flashing a phone with a micro SD card
1. With a card reader on your PC, format a non-SDHC (<=2GB) microSD card into FAT32 (tested to work up to a 4KB cluster size)
(the default size for a 1 GB would not work, also if it takes only a few seconds to format
try formating with some other slot/device. A 1 GB took over a minute to format correctly)
To format your Card - Open a DOS box and type/copy and paste this: ( format ?: /FS:FAT32 /A:1024 )
Replace the ? with whatever your SD cards drive letter is... ie: f, h, I.... Mine is G....
2. Copy the ROM to flash (xxxxxxxx.nbh) to the root of the microSD
3. Rename the ROM xxxxxxx.nbh to TITAIMG.nbh
4. Insert your card.
5. Force into the boot loader with POWER-CAMERA-RESET
6. Follow the instructions and you'll quickly flash your Titan...
7. You may have to soft reset once it says the update is complete
(If you are using UC let the customizations run so it will read the SDConfig.txt file)
This will work to flash with an official ROM and radio, I think regardless of the boot loader you have installed. But ensure that you have the correct boot loader (olipro 2.40 for this GPS ROMs) installed for when you do eventually finish with your flashing and are ready to boot into the OS.
Click to expand...
Click to collapse
so i have been trying this for a while tonight.. cant get it to work...
I am getting the Loading... screen.. all grey but that is it...
512mb micro sd... TITAIMG.NBH file exists...
any ideas??
I did not install olipro 2.40... should I??
alot of views but that is it..... hmm...
ok I installed nueSPL-2.47
so now it says.,.
TITA100
SPL-2.47No2Chem Titan SPL EVT CPLD-9
still cant get it...
now trying to boot to upgrade the rom I get the reg, green, blue, white part of the screen... and it says serial....
can anyone help me???
it sounds to me like you have nueSPL installed correctly.
In the past I have had problems with formatting sd cards, the only reliable way I have found to format them so that they work for flashing roms is to use the nue format utility... it is up somewhere on nuerom.com
It will erase everything on your card, so back it up first
after the card has been formatted, copy the "TITAIMG.nbh" file to the root of the card
Put the card in your phone and reboot into bootloader mode
it should detect that there is a rom image on the card and ask you to press the power button to continue.
The flashing process takes about 1 minute to complete (so much faster than using activesync)
Once everything is done it will say something like "process complete", and then you soft reset and you are done
which rom are you trying to install?
mpenguin14 said:
which rom are you trying to install?
Click to expand...
Click to collapse
yeah was weird... on about the 12th try of doing so much... copy rom, format, etc... eventually got it...
so which rom....
now I am ready for recommendations on this...
Here is what I use my phone for..
1. Phone - duhhhhh
2. GPS - Big time use....
2.a. Speedometer for my pickup truck... gpsspeedometer.exe
2.b. iGuidance
3. few games
4. Sirius radio via wifi
I do not have a data plan.... was going to get one soon but just bought a 2008 silverado z-71 crew cab.. so car payment is a bit much... so dont want to fork out the extra on a data plan.....
I have to check again but I think this is the one im going for...
Titan M2D Round 4 ROM (DCD 3.2.6 and TouchFlo 2D)
my biggy was getting the radio upgraded more importantly for better GPS... however I have got it to sync yet.... well im inside the house and cant get it to sync... raining outside too....
TeleFragger said:
yeah was weird... on about the 12th try of doing so much... copy rom, format, etc... eventually got it...
so which rom....
now I am ready for recommendations on this...
...
I have to check again but I think this is the one im going for...
Titan M2D Round 4 ROM (DCD 3.2.6 and TouchFlo 2D)
Click to expand...
Click to collapse
I am glad that you were able to get it working. I enjoy flashing different roms, but am not really a nit-picky user.
I fonally donated to no2chem today so that I can use his nueRom3-pre3, it is a pretty nice rom that gives you the option to disable your camera and get an extra 8 MB in free ram, I am also really liking the nueWifiSwitch. But like I said you have to donate to get the rom, and I have only been using it for 6 hours or so.
before that I was pretty much exclusively on a custom build of DCD 3.2.6, just a bare minimum rom, which I like because I flash quite often.
It does seem like people are liking the "Titan M2D Round 4 ROM" a lot. It looks pretty good, in fact it even includes a program that I made, Manilla 2D Customizer, which will let you tweak Manila 2D and apply some themes.
Good luck, and I hope flashing your rom via SD card goes a little bit smoother than your radio flash
Hi guys
I own a HTC TYTN (Vodafone 1605) having WM5 and would like to have latest updates and features on it. I checked HTC site and i suppose they are not offering any updates for this model.Please help since i am not very used in doing upgrades etc.
Thanks
Ashok
Start here!
DO THIS FIRST!(MOST IMPORTANT)
HARD SPL
http://forum.xda-developers.com/showthread.php?t=296722
THIS IS NEXT
SIM/CID Unlock
http://forum.xda-developers.com/showthread.php?t=293665
THEN GO HERE
Schap's WM6 ROM (It's great!)
http://forum.xda-developers.com/showthread.php?t=359458
IF YOU GET STUCK GO HERE
http://forum.xda-developers.com/showthread.php?t=455859
Mind you, Schaps is a very old rom now, go to the wm06 part of this forum to find roms that are more current.
It may be old but it still works great.
It might be old but i like it. It doesn't hang and all my 3rd party apps work flawlessly even TOMTOM 7.
What ROM would you suggest?
At the moment I'm using REVROM Lite. I changed the flash screens though as I like some others better. I also use Tomtom 7 though I have it installed on my sd card and just send a shortcut to windows startmenu folder. Have no probs whatsoever.
Its really fast and seems to be stable with me NOT having to soft reset at all for the last 2 days... You gotta admit thats pretty decent performance, I've also had no HR's or freezes. Could just be I've finally found the rom and setup that is good for me...
Cheers...
Yeh, i hear ya. I actually flashed two other ROMS on my phone tonight just to see what they were like, but i'm going back to schaps. It was stable and it seemed to give good battery life. I have all my 3rd party apps installed to my 8GB SD card to save space on my phone. Seems to work for me. Thanks for your input. Two heads are better than one unless one of them is a goathead. LOL Anyway thanks again.
Have been having similar problems upgrading my HTC TyTN from its official WM5 to the Official release of WM6. Every ROmor upgrade or program I have used has failed once it has switced the phone into bootloader mode even using Hard-SPL. Ive being crazy trying to find a solution. Hasnt help that Ive had enough trouble getting started thanks to using Vista-64bit and its driver signing problems. I have since sorted that problem and am now not getting any further with flashing the ROM.
I wouldnt class my self as an expert but I also would consider myself a novice as I build PC's and have flashed both my Xbox 360 and my PSP so am used to working in the shady underworld.
Vista Home premium
Ok here's what i've found with vista. I run AVG anti virus and spybot search and destroy on my laptop. When i use my laptop to flash a rom to my phone i have to turn both off. Even then when i flashed to the OEM cingular rom i had to put my phone in bootloader for it to flash. If i let the program put it into bootloader it wouldn't work. Now, when i flashed to shcaps and my preferred radio rom it worked fine as long as advanced network funtionality WAS checked. Before i found these fixes though i used the SD flash method which is in my opinion the best way to go since it is so simple. That is the way i flashed my Axim X51V so i was familiar with that method, i just had to figure out the correct procedure for the phone.
This is from the post that explains SD flash.
1. download hardspl v7 from the first post.
2. extract ruu_signed.nbh and rename it to HERMIMG.nbh
3. copy it to a microsd card, make sure the card is formatted as fat32
4. download sspl-herm from here
5. extract SSPL-HERM.exe and copy it to your phone.
6. insert sd card and run sspl-herm.exe on the phone.
7. you should see the tri-color screen and then it should change to this
8. press power button to start flashing
9. reset when you get the msg that its done
Good luck
OH and if you need the official Cingular WM6 ROM you can download it here.
If you have Hard SPL installed ignore the steps using SSPL.exe as that is Soft SPL. It's not as safe as Hard SPL.
Cheers...
PS. make sure you use a 2Gb or less sd card as the bootloader won't recognise sdhc cards, format FAT32 (most cards are default formatted FAT) & make sure of your spelling as it won't work otherwise - hermimg.nbh.
thankĀ“s you all for help me upgrade HTC TYNT
I am sure some of you are going to read this and shake your head but I need to know what is the whole purpose of updating your ROM on your phone. I currently have a US Cellular PPC 6800 and US Cellular never has anything on their site for new and cool things for their phones. I would like to update the phone to Windows 6.1 not for any particular reason just to say I did it. Is their certain features on this phone that I am missing out on because I have a stock ROM? By upgrading my ROM what features will I be able to get or do?
Thanks for your answers.
speed, speed, more speed, memory tweaks, battery tweaks
Really. I like that. I will start reading threads and getting a better understanding of this whole ROM upgrade. Any particular ROM that someone can suggest so I can read more on it. Anyone have any good words of wisdom on things to do or avoid?
what do you like in your roms? with programs? or barebones?
See that is what I need to learn yet. The differences in the ROM's. But I would have to say I like programs.
then r4r reloaded is the way to go by scrosler or bitserve. to unlock use nuespl
I see that nueSPL-2.47 is the latest version and I assume that would be the version I would use. it says "DO NOT USE with a NON GPS RADIO (2.xx). Only use with GPS RADIOS (3.xx). A version check will be added soon." How can I verify this?
What is the actual purpose of the nueSPL?
I don't mind getting my hands dirty and doing some reading but I am very new to the whole world of upgrading my phone. The fear is if I do something wrong then I have a very expensive piece of junk. I have worked on UNIX machines for the last 15 years so if this was a computer no problems but like I said earlier I know nothing about phones.
Thanks for your help
have you decided on a rom? kitchen or RUU file? let me know which one, then, ill help you unlock and install your rom
I am still researching the best one, or the one I think I would like to try. Thanks for your help and I will get back to you when I think I fully understand.
ok, this is what I believe to be true. a ROM and RUU are pretty much the same and a kitchen allows you to pick and choose which apps you want to install. What I am looking for is a way to allow me to have more features for the phone (ie. turn on GPS and upgrade to WM6.1) but yet also have some of the same programs I use all the time or be able to install the programs I use ( Office, Opera, Calendar, ) Things like that. Since you have way more knowledge on this then I do, with what I mentioned what would you suggest?
go here http://forum.xda-developers.com/showthread.php?t=444342
then go into scrosler website and download the LOADED EDITION
have two things ready
1 nuespl (to unlock)
1 loaded edition rom (win6.1 GPS)
do you have a sdcard? what size?
GeLopez said:
go here http://forum.xda-developers.com/showthread.php?t=444342
then go into scrosler website and download the LOADED EDITION
have two things ready
1 nuespl (to unlock)
1 loaded edition rom (win6.1 GPS)
do you have a sdcard? what size?
Click to expand...
Click to collapse
You will also need an updated radio, I recommend 3.42.40 or 3.42.50.
You have to do SPL first, then radio, then rom.
BTC
I do not have a spare SD Card I am going to buy one and I have read that I need 1 no more then 2GB and to format it as FAT16
ok, I have downloaded Radio ROM 3.42.50, R4RLoaded, going to get SD NueSPL, and 2GB SD Card.
jskoland said:
I do not have a spare SD Card I am going to buy one and I have read that I need 1 no more then 2GB and to format it as FAT16
Click to expand...
Click to collapse
might want to make that fat32
nuespl will format the card as fat 32 once we get it running
ok I am ready to go, I have an extra 1GB microSD card, After some reading, I am going to copy nueSPL to my phone with ActiveSync, SPL will format the 1GB card and then the unlock process will begin, After that I will install the ROM ( I need to re-read that because I forgot how to do it) and then after the ROM install the RADIO using the SD card method.
jskoland said:
ok I am ready to go, I have an extra 1GB microSD card, After some reading, I am going to copy nueSPL to my phone with ActiveSync, SPL will format the 1GB card and then the unlock process will begin, After that I will install the ROM ( I need to re-read that because I forgot how to do it) and then after the ROM install the RADIO using the SD card method.
Click to expand...
Click to collapse
ill help you with the installation because its quite simple
once you get it unlock
rename your rom (ruu_signed.nbh) to TITAimg.nbh
copy TITAimg.nbh to storage card (using whatever activesync or card reader)
put phone in tri-color screen (in case you dont know it's power+camera+reset hold for 2 seconds)
that will install your rom.
the steps for upgrading the radio are the same:
delete previous titaimg.nbh file and replace it with your radio (titaimg.nbh) file
tricolor screen
done
Ok thanks for you help. going to try my very first ROM upgrade right now
jskoland said:
Ok thanks for you help. going to try my very first ROM upgrade right now
Click to expand...
Click to collapse
go for it. ill keep my eyes on this thread
and my ears up for screaming