Related
HELLO my friends!
Can you help me to revive my qtek 9100 whit Jtag interface.
I need testpoins for Jtag of G4 mainboard (TDO,TDI,TMS,TCK...)
Thanks in advance for ALL!!!
To the best of my knowledge nobody has revived their wizard using JTAG contacts. It might be a myth, or just unproven yet.
Wizard jtag Done yeeeeehaaa!
ok i made it happen n have done that successfully
i made a mistake of doing hard spl thing before downgrading to t mobile custom rom, first it was stuck on splash screen n than was totally dead after resetting
i searched n found the procedure of jtag it n bring back to life, im very happy i did it with slight modifications according to my logic n made it till bootloader, much thanks to all who left so many ideas and materials at different places. ok now my problem is that it does the whole flashing but after that it gets back to boot loader with the same incorrect ipl spl
i guess ill be needing a monster pack with ipl spl included i tried ruu mun otherwise the nb sawith the custom gave invalid tool msg. any ideas guys?
fsl13 said:
ok i made it happen n have done that successfully
i made a mistake of doing hard spl thing before downgrading to t mobile custom rom, first it was stuck on splash screen n than was totally dead after resetting
i searched n found the procedure of jtag it n bring back to life, im very happy i did it with slight modifications according to my logic n made it till bootloader, much thanks to all who left so many ideas and materials at different places. ok now my problem is that it does the whole flashing but after that it gets back to boot loader with the same incorrect ipl spl
i guess ill be needing a monster pack with ipl spl included i tried ruu mun otherwise the nb sawith the custom gave invalid tool msg. any ideas guys?
Click to expand...
Click to collapse
HEY lissten HOW DID U GET THE places where to solder the JTAG cables to motherboard ? please answere
Wizard jtag test points
I found this on another site, hope it is some help.
I am extremely sorry that ihave been away and couldnt respond
Ok im all ears and here to help you till you make it to the end
now tell me your actuall status and what you need
i luckily have all the files needed to jtag but
right these unfortunately i have a very bad internet connection
PM me and we ll take it from there
dont worry i am with you now
Mr FSL13
Can you please come to PM or IM
i have also a one WIZA200 Dead while Update
and i need to JTAG it
its very urgent
can you please help me in this problem?
Thanks in Advance
[hello
thank you , i woulid if you cna help me to make the same , means jtag for my htc wizard i did the same mistake , is dead now, , thank you
souriant said:
[hello
thank you , i woulid if you cna help me to make the same , means jtag for my htc wizard i did the same mistake , is dead now, , thank you
Click to expand...
Click to collapse
RIFF JTAG Wizard look at http://www.jtagbox.com/tag/security-features/
i saw lot of people have dead prophet problem, so i am here now to make a new thread to all this people and i hope to make it useful.
now we start
** FIRST : lets know names of prophet :
I mate Jamin, O2 XDA Neo, Qtek S200, Dopod 818 pro, Dopod 830, SPV M600, VPA Compact S.
** SECOND : we must know that before we trying to do any updating or change roms on my prophet i just need to do which called unlock for the prophet and then we after that been able to change any rom on my ( jamin ) and of course u need to be careful about Your device is it G4 or G3 ,
# and how we know its G4 Or G3 ?
# when u start Your Device u will see some numbers on left,
---------------------
IPL: 1.00.000
SPL: 2.20.000
GSM: 02.61.21
OS: 3.0.0.0
--------------------
and may be changed and that goes to the rom which You have, now we look for the last number on ( IPL and SPL ) , if we found it ( 0 ) it means You r G3 and if it ( 1 ) so You r G4 .
** THIRD : lets go to unlock , i will put programs in this thread it will help u in unlock.
-- Sync your device with computer and open the file u download it called HardSpl you will find two files one one foe G3 and G4 open your kind then you'll find a file called (( hardspl.bat )) okay, be sure your device is connected to computer then open the file and follow instruction and it will reset your device ,
now u ready to change rom.
TO BE CONTINUED
hey guys
i tried to attachment the file now put it gives me database problem, so i will be after it to attach don't worry pals. see you later.
hey guys
i tried to attachment the file now put it gives me database problem, so i will be after it to attach don't worry pals. see you later.
if any one can help please contact me.
hello
my device is jamin g4
it stopsat the boot loader and dono thing
can u help me please?
my e-mail is [email protected]
and suddenly after trying to update the spl been 1.01
please help me
can i fix it?
waiting for ur help
What is the IPL and SPL?
If the wiki where up, I'd suggest looking at that, but as it is I'll explain it now...
What ROM where you attempting to upgrade to?
To get the device back, I would say "Read the wiki" but it's down!!!
Download this ROM.
In ActiveSync, disable "connect through USB" (File->Connection Settings).
Put the device into bootloader (the three coloured screen) and connect it to the computer using the USB cable.
Run the file you downloaded earlier. This should then install a new ROM.
From there, just wait for it to finish.
Now, it should work!
From there, you could re install the Orange WM5 ROM, or try upgrading to WM6. Make sure you read all the relevant guides first!
thanks alot i did as u said but it stops at 80% or 88%
then show this message (error 326 invalid command )
please help me
i'm feeling bad
my mail is [email protected]
What brand the device? Has it been SIM unlocked?
hi again brothers, pal zerocool. first u must unlock ur device to be able to accept any rom after that and solve pproblems.
first flash this rom its offecial and it solve dead prophet problems.
then make hard spl by program open file called hardspl.bat.
make hard reset.
flash ur rom u want.
make hard reset again.
then enjoy.
i uploaded the hardspl program but i couldnt upload the rom its so big so u can look in ur mail u will find the solution.
u can extract file by any program for zip.and tell me the news
dont forget to look to ur mail. see all of u later
Dead prophet
Hi guys,
I have been using a sh... Nokia sine I broke my prophet G4 in december by upgrading the OS.
I had downgraded first to NVID and then I tried to upgrade and it fails at 95%.
Sine this day, my prophet seem totally dead, no light when plug on both charger or computer, windows do not recognize at all the device because it is turned off. And it really do not seem to charge...
I am living in China now and a guy told me I had to change the PB board...The ost is 100Euros, but I am almost sure I an find another solution...
The weird thing is I cannot charge it at all ( I mean no lights but does it charge a little?).
The guy tested my prophet with another battery and in that ase, it is stuck on the bootloader.
We tried several roms and it always fails at 95% and the error is 200 something, maybe 245 or 243, I do not remember sorry...
Is my phone hardware is dead? or it is just a software problem and I did not see the right guy?
Do I need to buy a new battery? I have read that sometimes the device is not able to recognize it even if it the offiial one and even if it is working on another device...
PLease help me I don't want to loose this phone that I've been using for almost 3 years...
Otherwise I will switch to an iphone but I am not sure to be as happy than I was with my prophet.
Xie Xie for your advice and answers.
Guilh1
Can it enter bootloader at all?
If yes, what are the IPL and SPL?
If not, it will be a hardware problem (may just be connectors to the battery but may be something more).
the only way of recovery is using jtag
but 1st we must discover the location of jtag pins on motherboard
I just do not know because with my actual battery, anything is possible....
when I tried with the guy and a new battery it was blocked on the bootloader, but don't remember the IPL and SPL...sorry
I may be right about the battery onnectors though, but the problems seem to be from the phone connectors or the battery it self???
Thank you anyway for your very quick reply
when I tried with the guy and a new battery it was blocked on the bootloader, but don't remember the IPL and SPL...sorry
Click to expand...
Click to collapse
If it can enter bootloader, it is almost certainly your battery at fault!
Ok so i burnt my battery during the upgrade...
But why is it still blocking at 95% when he tried to put a rom?
With his battery, it was stuck on the bootloader and not possible to install a rom, even a NVID WM5...
I really do not know what to do...
Thanks again for your help
My iMate JAMin is dead; I was in the middle of flashing it when it froze, now when I turn it on, I get the Tri-color screen with the following ...
IPL: 2.13.0001
SPL: 2.13.0001
No [BUSB[/B] is detected. So now I need a way to flash it from the SD Card. I can not even see the HTC startup screen anymore, it just jumps directly into the tri-color screen.
Ok so i burnt my battery during the upgrade...
But why is it still blocking at 95% when he tried to put a rom?
With his battery, it was stuck on the bootloader and not possible to install a rom, even a NVID WM5...
I really do not know what to do...
Thanks again for your help
Click to expand...
Click to collapse
Do you know which ROM? Is your device branded, and is it SIM locked?
Do you know the IPL/SPL? Did they end with the same numbers?
My iMate JAMin is dead; I was in the middle of flashing it when it froze, now when I turn it on, I get the Tri-color screen with the following ...
IPL: 2.13.0001
SPL: 2.13.0001
No [BUSB[/b] is detected. So now I need a way to flash it from the SD Card. I can not even see the HTC startup screen anymore, it just jumps directly into the tri-color screen.
Click to expand...
Click to collapse
Please look at this if you want more help, post here...
thanks alot dear samuraititio
but i can't flash it
it writes (no vender id)
help me please i tried another tool with the same nbf file it stops at 80%
and it automatically enter the boot loader
and i can't do ant thing
its information
jamin/g4
ipl 2.13.0001
spl 1.01
i think my problem is in the spl coz it was 2.13.0001
and now it's 1.01
how can i fix it please i still starter in this way so i'm trying;
help soon please
You now have a G3 SPL on a G4 Device.
What did you flash exactly?
l3v5y said:
Do you know which ROM? Is your device branded, and is it SIM locked?
Do you know the IPL/SPL? Did they end with the same numbers?
Please look at this if you want more help, post here...
Click to expand...
Click to collapse
hello pal i3v5y
i have the same problem
idid what u said the flashing stops at 80%
i need ur help please
i'm online at the moment and u too help me soon if u can please
my e-mail is [email protected]
waiting for u i don't have any other device to use and i need it
l3v5y said:
You now have a G3 SPL on a G4 Device.
What did you flash exactly?
Click to expand...
Click to collapse
now i flashed the official rom of jamin but it stopped at 80%
Hi,
i flashed a rom 2 weeks ago, everything went well. yesterday i wanted to flash another os but before i could flash it, it seemed to get bricked. It stucks on the "HTC Splash" (not the WM6 Splash). I read a lot of threads and wiki threads but i don't unterstand anything! What i've to do to unbrick my phone? I tried to flash another rom but after 0% of flashing a error appears.... flashing with sd card doesn't work, too it changes to bootloader after the "Loading..." screen
i havent got hardspl or something...
please help!
UPDATE: i got the sd flashing to work... same thing but: now it stucks at the WM splash, not the t-mobile/htc one...
You need to find out what SPL you have (I'm guessing 2.03 but if you have 2.10 olipro then its got Hard SPl on it) and then do a search for "bricked SPL x.xx". You will probably find a HEAP of posts. However, some advice that seems to recover a small minority (sometimes with the "No GSM" error) -
1st thing to do is do a hard reset. Both softkeys and reset with stylus. Hold in all buttons until it asks if you want to reset to factory. Press "R" on the slideout keyboard and the "Space".
Hopefully this will fix. If it doesn't, Put it in bootloader, connect to pc (make sure "Allow USB Connection" Active Sync settings have been unticked) and run the SHIPPED STOCK ROM. This is the rom the Hermes came with originally. This MAY fix it otherwise you're in for some major reading and hair pulling.
If you should fix this then PLEASE, for the love of god, Hard SPL your Hermes before going into the wide world of flashing.....
Good Luck...
thanks i'll try it. hard reset causes kinda... nothing^^
i hope i can fix it otherwise i'll buy a touch pro
...but i think it doesn't work, because i flashed a shipped rom via sd card yesterday and the problem is still there... isn't there any way to put hard spl on my device, yet?
Try re-installing the stock rom again using sd card (if thatys how you did it last time), it could've been a bad flash. I've had those a couple of times myself. Just remember to install Hard SPL if you're successful as it makes it SOOOO much easier to recover from bad flashes.
Last thing to check would be if you have "bad blocks" using MTTY. If the boot sector has been stuffed up this may cause this problem. Do a search through the wiki, its been covered extensively...
Cheers...
okay i think my problem is solved: t-mobile replaced my device
first thing i'll do with my new device: HardSPL^^
anyhow thanks!
Upgrade successful but now stuck
I have a Three (au) Dopod 838 pro, which I upgraded from the original Windows Mobile 5 to the Three Windows Mobile 6.0 ROM. Unfortunately I didn't read up on this site first, I thought it would be straightforward since it was a ROM from the manufacturer and all, so I haven't Hard SSPL.
The upgrade reported as successful and my PC disconnected but the phone won't boot, it sticks at the Dopod screen with some numbers at the bottom. They are:
M 05 R 1.47.30.10
S 04 G 32.80.7020.20H
B 07 D 3.54
I have tried hard resetting, and returning the phone to bootloader and reflashing the same new ROM image, always with the same result.
On the bootloader, it says
HERM100
IPL-1.04
HERM100
SPL-2.03
Is there anything which can be done or is it a trip to the service centre (wherever that is)?
Just checking - Hard reset = both soft keys above the dialler closest to the lcd and reset with stylus. Hold in until it asks if you want to reset to factory. Press r on slideout keyboard then space.
This is a hard reset, not just using the stylus.
Otherwise, you have a LOT of reading material to go through with (maybe) no actual solution.
Cheers...
tried that
Thanks, but yes, I had tried that, a number of times. I think the phone will be going to a service centre today.
hi guys
I have a bricked hermes
DOPOD 8525 -> WM 6.1 Professional
From bootloader screen
HERM100 IPL-1.01
bootloader SPL-1,40.01ipro
Tried to flash ROM using safe SSPL with RUUwrapper.
At completion of flash both my mobiler & win mobile device centre disconected or lost connection with device, after soft reset will only load up to second HTC screen. How can I recover from this brick? device manager recognises HTC usb sync when plugged in but I can't connect to re flash rom.
Reading helps my friend
Get to bootloader, press ok and power on left and right respectively and stick stylus in all at same time.
that should bring up tricolour screen.
Download your imate jasjam official ROM
EDIT i think you got a dopod so the dopod ROM is what you want from my 4shared or wiki!!
from the wiki or from my 4shared, and flash it while it is in boot loader mode.
then you need to flash hard spl one of the first stickys on this thread that you have just posted to.
Then flash your desired rom.
Thank you Zocster
Got it unbricked & working, thanks to you I have a lot of trouble reading as I am leagally blind but get by with T2V & magnifiers most times. however searching threads is a lot harder than for most.
thanks
Lou
PS if you ever cross the tasman drop me a line
loulian, to make it easier to recover from bricks, It would be best if you flashed Hard SPL V7 from here - http://forum.xda-developers.com/showthread.php?t=296722
It won't guarantee a flawless flash but will help if something goes wrong by giving you a GOOD chance of recovery.
You can then use the sd card method and make life easier by not having to worry about pc crashes, cables being pulled, blackouts or those annoying "sync" errros.
Cheers...
Also if you have trouble setting up your Hermes after a flash/hard reset because of the alignment points being hard to see, It would be a good idea to download this -
http://www.codefactory.es/en/downloads.asp?id=44
It will, after you save the settings, allow you to use your PC to set up the Alignment point if you need to Hard Reset or flash your phone making it load the os to the today screen.
zocster said:
Reading helps my friend
Get to bootloader, press ok and power on left and right respectively and stick stylus in all at same time.
that should bring up tricolour screen.
Download your imate jasjam official ROM
EDIT i think you got a dopod so the dopod ROM is what you want from my 4shared or wiki!!
from the wiki or from my 4shared, and flash it while it is in boot loader mode.
then you need to flash hard spl one of the first stickys on this thread that you have just posted to.
Then flash your desired rom.
Click to expand...
Click to collapse
Sorry to ask a stupid question. I have the same problem, but when i try to flush it from a TriColor mode i get a communication error, it complains about activesynch not connected. BTY mine is cingular 8525 so i am trying to use one of the cingular roms.
Dear Members,
I tried to upgrade my JasJam with "838Pro_HK_ENG_WM6_Upgrade_20070712"
Which worked with other JasJams (Many of my friends has it working).
On upgrading, it stucked on 11% saying Error [262]
I went through recovery, and it said remove the USB cable, remove the Battry, Return it, start the phone, connect the USB, and its recovered.
After that Its again stucked in 100% and the same senario is happening.
Please tell me is there any possibility to restore my phone working.
Its stuck now, and only the (Three color screen) is on the screen.
Hard reset, soft reset is not functioning, and the phone refused to show anything except the three color screen.
I searched the forum, but found no relative article, I am searching since two days your forum and I know that no other forums can help me in this as I was always getting my help from yours.
Thanks for your time.
HERM100
IPL-1.04
HERM100
SPL-1. 40. 0lopro
If you're using XP then untick "Allow USB Connection" in activesync.
Reset to bootloader on your Hermes, Hold power, OK button above flywheel and reset with stylus.You will get the same screen you have now but it won't be a f*&%ed up version of bootloader. Connect to PC by USB and Install Hard SPL V7, found here - http://forum.xda-developers.com/showthread.php?t=296722
After this, use the sd card method to install the ROM.
1. Format a 2Gb or less sd card FAT32. ?CFopy the .nbh file of the rom you want to it and rename to hermimg.nbh .
2. Insert into phone and reset to bootloader.
3 If you did everything right then follow the prompts...
Cheers...
Again problem!
Dear ultramag69,
Thank you for your fast reply.
I did (untick) that option in the ActiveSync.
And also did reset to the device by holding the Power + Ok (under the flywheel) with Stylus reset.
After that I downloaded "Hard SPL V7" and tried to update.
First of all, in the "Hard SPL V7" there was only the last option active, and there was down a checkbox also active, but when choosing the last option, checkbox bocomes like everything else disabled.
However, I got the erro 286
I felt like the Device disconnected from USB and reconnected again (Windows gave me the sound when you remove some USB device and you re-connect it again) :-|
I don't know what to do with this dead device now !
Thank you very very much for your time and help
Don't quote me on this as I suspect you need Hard SPL V7 but, as yo've tried things out and you're about to quit anyway, Try using the sd card to update the Stock rom, the rom that came on your Hermes, or updated version. It might let you do it if the CID matches.
I don't believe SPL 1.40 allowed you to flash ANY rom but it may let you re-install the stock rom BUT it must be the original carrier software it came with. If you had Telstra rom on it when you got it, it must be a telstra rom you flash. Make sure its for the right country too as some carriers are all over the world.
Cheers...
Hello ultramag69,
Thanks alot for your reply.
Having my i-mate dead, is really interesting.
I am trying to recover it up, Mine came with (HTC) logo when booting, and I did flushed it with Dopod.
But recently, the network stopped, and I asked some experts, they said it need new OS (They ment to re-flush the ROM).
I tried with the same Dopod that was successful before, and its now stucked on 11%.
I even downloaded the Telstra but the same, it stucked on 13%.
This is my entire story, and still I am trying to get it up.
Thanks alot for your helping. nice of you.
And for all who read my post, if they had such experience before, please help.
Hello ultramag69,
Thanks alot for your reply.
Having my i-mate dead, is really interesting.
I am trying to recover it up, Mine came with (HTC) logo when booting, and I did flushed it with Dopod.
But recently, the network stopped, and I asked some experts, they said it need new OS (They ment to re-flush the ROM).
I tried with the same Dopod that was successful before, and its now stucked on 11%.
I even downloaded the Telstra but the same, it stucked on 13%.
This is my entire story, and still I am trying to get it up.
Thanks alot for your helping. nice of you.
And for all who read my post, if they had such experience before, please help.
If you can, try to find the original SHIPPED STOCK ROM. It may be your Hermes won't be recoverable as the flash stopped in the radio rom part. Most people use a cooked rom as this has the radio rom part out.
I personally use the sd card method to flash my roms so there are no sync errors or accidents with my PC. But you need Hard SPL V7 installed to get that to work with any but the shipped rom.
DON'T try flashing anything but the shipped rom or you will loose all chances of recovering your Hermes.
The only other suggestion would be to flash the SHIPPED RADIO ROM, but you need to know what radio it was before you flashed it with the dopod rom.
Unfortunately the radio rom is the Achilles heel of our phone series. Any problems during flashing of that means we pretty much end up with a brick 99% of the time. Most people are stuck and the rest seem to have limited success reflashing the radio. AVERY small percentage get it working with no trouble, but its a REALLY small amount of people.
Good luck, Make sure you flash with the SHIPPED STOCK ROM to improve your chances of success.
Cheers...
Ultramag69, Thanks alot for your consideration.
Flusching using SD card didn't success with SPL V7.
I formatted my MicroSD card, 2GB with Fat32 FS.
After that I copied the file that came with the zip archive (RUU_signed.nbh) and renamed as required: (herming.nbh).
And I put it in my i-mate, and holded the (Power + OK under flyweel) then restarted using the stylus, It showed me the tri-color screen, then it shows (Loading...) with Gray background screen (Which is normally the flusching screen) but it returned to the tri-color screen.
Any suggestions to get this SPL V7 installed successfully ?
I tried with all my (.nbh) files that I have downloaded from all sources, but its the same screen.
I think something is really wrong with me i-mate, should I take it to some Hard-ware service center ? and what can be damaged and need to be replaced in such cases ?
I am very excited in getting it working again.
Thanks alot.
Cheers...
I had bricked my Hermes a couple o' times, because of a rom I cooked half-way ( LOL ). Each time I had to flash back to the stock rom as suggested. Don't lose hope, cuz there's some people who will tell you just to accept it as bricked. You could also take the sucker apart and use jtags to flash. Most types of bricks can be solved when it comes to the Hermes. There's a thread somewhere that polled the different types of bricks, and except for radio bricks, most can be solved. If you unbrick it try 6.5 .... !!! My rom is cooked all the way now
Arwany, did you run the SSPL.exe file in the sd card instructions for Hard SPL found on page 116, post 1160 of the Hard SPL thread? You need a version of Soft SPL (SSPL) to flash using the sd card as the CID must be bypassed. The reason we Hard SPL our Hermes is because its safer. Its worthwhile flashing the SPL using unsafe SSPL (even if you use the pc you have Soft SPL installed) as its a short flash, flashing a rom (especially stock roms with the radio rom inside) is a riskier and longer flash.
Cheers...
I had the same problem.. All you have to do is establish a connection with Actisync, then run the Updater. There will be 3 colors on your Screen, sont worry, just wait 10-15 min and your should be done with the setup.
Want to help
Arwany said:
Ultramag69, Thanks alot for your consideration.
Flusching using SD card........ with the zip archive (RUU_signed.nbh) and renamed as required: (herming.nbh).
And I put it in my i-mate..........
Click to expand...
Click to collapse
Hi,Just to tell You that I've noticed a little spelling mistake.You've written "herming.nbh" But it should be "Hermimg.nbh".
Not the 1st person to make that mistake, and probably won't be the last.....
Hi All,
Yeah, that worked out for me, I could successfully flush my JasJam with that.
Thanks for your reply.
I am still facing problem when trying to flush with other OS, its always stuck on the GSM line.
I am using the SD flush method.
Any suggestions ?
THank s alot for your help!
If you have the no GSM problem the only way to, maybe, fix is to flash the original SHIPPED STOCK ROM, or the original radio rom. Flashing anything else may result in a permanent brick...
If it doesn't succeed then, sorry, its not repairable. Can be used as a PDA but not as a phone ever again.
Cheers...
Thansks Ultramag69, for all the helps, It solved my main problem.
You also Ekonkar, your comments was so helpful.
I will try to do some hardware repairing in some Mobile shop, they may get it up again !
To fix it will cost more than to get a new device... They'll tell you they can't fix it or it needs a new mainboard. Will still cost you for this nugget of info. My advice, buy a Hermes off ebay, either working or not. If its not, make sure its screen related problem cos you have the parts to fix... Unless your screen has gone bung too...
Cheers...
I gave it to the repairing guy, he replaced the GSM item and its up and running now for only 20$.
Prost :-D
Sweet, You should post where and what country so others in the same situation might be able to get their Hermes up & running.