well i m using HP rw 6815, n last night i had flashed a O2 6.5 rom , later i was unsatisfied with tat rom,
so i went 2 change it, n during tat process, my phone turned off, n now it doesnt switch on, 1ce i managed 2 go 2 boot screen thr i cud see hp logo n bl-0.0.0 can ne1 help me out with it, how do i put bootloader in phone.. neither my pc detects the phone... NOW IT DOESNT EVEN TURN ON ... I HAD CHARGED IT COMPLETELY,STILL IT DOESNT TURNS ON. help appriciated
SOME PLEASE HELP
uzi21 said:
well i m using HP rw 6815, n last night i had flashed a O2 6.5 rom , later i was unsatisfied with tat rom,
so i went 2 change it, n during tat process, my phone turned off, n now it doesnt switch on, 1ce i managed 2 go 2 boot screen thr i cud see hp logo n bl-0.0.0 can ne1 help me out with it, how do i put bootloader in phone.. neither my pc detects the phone... NOW IT DOESNT EVEN TURN ON ... I HAD CHARGED IT COMPLETELY,STILL IT DOESNT TURNS ON. help appriciated
SOME PLEASE HELP
Click to expand...
Click to collapse
Firstly copy a rw6815 rom into MiniSD card (like installing a rom).
Put away the battery for 10 minutes. After 10 minutes insert the battery again.
Pres - and - button and the reset button with your stylus. Take the stylus back but continue to press - and - until something changes on the screen. This could be 1 or 2 minutes. After something changes you can release the - and - buttons and then new rom should start to install. After 20 minutes, you can use your rw6815.
Note: If this fails, maybe you need to install the bootloader before the new rom.
Use 68xx Bootloader 1.0.1 => HP_BL1.0.1.rar (instead of 1.0.5)
Good luck.
Related
Hi
Just got a prophet and ran a wm6 installation
now I can't get past the startup screen; it freezes where it shows the OS versions. Reseting it doesn't work either. My PC cant connect to it, altough it detects it for a few seconds when I power it up.
Thanks
fonzy99 said:
Hi
Just got a prophet and ran a wm6 installation
now I can't get past the startup screen; it freezes where it shows the OS versions. Reseting it doesn't work either. My PC cant connect to it, altough it detects it for a few seconds when I power it up.
Thanks
Click to expand...
Click to collapse
OH noooooo , you broke your phone!!!!
Ah just kidding ... you haven't broken your phone! not yet
Just read this guide you will be fine :
http://forum.xda-developers.com/showthread.php?t=310452
This has been explained in the above guide but just to make you feel better about your phone try this :
Hold Camera button and press reset. keep holding the camera button till you get to a screen with 3 color (bootloader screen). then connect your phone to your computer and flash a wm5 ROM
Good luck.
OK got it !
Thanks
BTW does labatt ice still taste like it used to?
I download the rom image from pda-hack.net in this url:
http://pda-hack.net/forum/index.php?showtopic=50
as well as the extrom, then fully charge my battery and follow these instructions:
1 diskimg.rar (40,6 Mb) - main OS, decompress this archive in SD Card root directory
2. pda-hack.net_rw68xx_ExtROM_emul.cab (3,97 Mb) - some applications needs ExtROM, this package can emulate it. Install after flash or put it into '\Cabs' directory before flashing for autoinstall
3. To flash press & hold soft-keys, then push reset, after HP logo is appear, release soft-keys and don't touch anything. After flashing device automatic reboot in hard reset.
I don't put the content of cabs.rar into my \Cabs, because I don't want to install these.
I use my 2G sandisk card to flash my 6828. When I boot into bootloader, the hp screen appears with blu1.0.5 at bottom-left cornel for about 20 minutes and then it blacks. I tried to get into bootloader mode but fails, also I tried to hardreset it ,but no response.
Is there a way to resurrect it .THANKS THANKS THANKS!!
Have you removed battery out around 5 to ten mins. and put it back at the same time with quickly go to boothloader like someone siad before?
I think it may help. Coz, I have 2 machines of 6828 me and my friend. One is fine flashing rom to WM 6 but another one meet the problem close to you. After waiting for 45 mins. I decide to remove batt around 5 mins. and bootloader again like what I read from some threat here and it works. I finally finish flash rom to WM6 both.
Good luck.
i managed to resurrect it. Take out battery, wait, press both soft key, at the same time put battery in, wait a second, wait a moment, it will be in bootloader mode.
uh.. anyone can help me?? i have the same problem.. xD
HI!
helloworld1 said:
i managed to resurrect it. Take out battery, wait, press both soft key, at the same time put battery in, wait a second, wait a moment, it will be in bootloader mode.
Click to expand...
Click to collapse
http://www.pdaviet.net/showthread.php?t=12439
ALL YOU NEED
I had the same problem. now no response at all. I am now taking the battery out and hope it works....
But still can't boot, i already tried to press the both - softkey, remove the batt, re plug the batt, and softreset , still no response, then i release the both - button...
what should i know now ? any idea ?
calling for help here,playing too much to flash this handset, and in my last progress to flash it...after 100% finish...nothing comes up,not even BL mode...
just black out..i guess my hp dead...right?
any solution?or i have to take to HP service centre?
however connect to the usb,the led light green/red still on...
any body help??
no1?
Try this way :
- Take out miniSD card.
- Press both softkey and remove battery then put it back again (Don't unpress two softkeys) then softreset...
- Wait 2-3 secords
If it appear HP Bootloader Screen, your device not dead. You can flash it again.
HP 6828 Dead Lock due to Flashed with Atom Rom
nhocbanme said:
Try this way :
- Take out miniSD card.
- Press both softkey and remove battery then put it back again (Don't unpress two softkeys) then softreset...
- Wait 2-3 secords
If it appear HP Bootloader Screen, your device not dead. You can flash it again.
Click to expand...
Click to collapse
nhocbanme need your very kind help,
my buddy mistakenly flashed my HP 6828 using different Rom, probably using Atom Rom and as result my HP 6828 seems heading the the end of the world.
Please advice me what should i do to recover back my pity 6828 life ?
thanking You in advanced
Eddie
nhocbanme said:
Try this way :
- Take out miniSD card.
- Press both softkey and remove battery then put it back again (Don't unpress two softkeys) then softreset...
- Wait 2-3 secords
If it appear HP Bootloader Screen, your device not dead. You can flash it again.
Click to expand...
Click to collapse
thank's.....nhocbanme
alimx said:
thank's.....nhocbanme
Click to expand...
Click to collapse
mm guys dats nt a problem u can retrieve it am aso using ATOMS bbot loader her hp rw6828
nt u need to flash 1ly d ROM>....to a Supported aii recommend u to use helloworlds ROM...
nhocbanme said:
Try this way :
- Take out miniSD card.
- Press both softkey and remove battery then put it back again (Don't unpress two softkeys) then softreset...
- Wait 2-3 secords
If it appear HP Bootloader Screen, your device not dead. You can flash it again.
Click to expand...
Click to collapse
thanks, my 6828 show the HP Bootloader screen now. but how to continue ?
no respone when I press the any key . or insert the miniSD card the do again the step ?
Oh ! yes ! insert the miniSD and do the step again.
my 6828 upgrade to WM6.1 now !!
Thank you very much, I was going crazy and I thought I had a brick but in the end without problems and is updated and I ok
forgive me for the English from google
jeswang said:
thanks, my 6828 show the HP Bootloader screen now. but how to continue ?
no respone when I press the any key . or insert the miniSD card the do again the step ?
Click to expand...
Click to collapse
All settled.Thank you guys.
6828 dead
con't boot when iput the battery red&green button lights on... help me!
In my case. I do any way it can'y start my device. My HP service center tell me it must be change mainboard. But I don't change. But I try to open it again. I found this way.
I think you will try this way as me.
- remove battery in a few minite.
- put battery back again.
- plug a battery charge. (not a cable sync)
- If green and red is on. I think it ok. If it not on, you will try first choice.
- Press both softkey ,power switch, soft reset to start bootloader at the same time. Don't press power switch at first.
I think it can be open your device on to bootloader. Flash it again.
Chanutpong said:
In my case. I do any way it can'y start my device. My HP service center tell me it must be change mainboard. But I don't change. But I try to open it again. I found this way.
I think you will try this way as me.
- remove battery in a few minite.
- put battery back again.
- plug a battery charge. (not a cable sync)
- If green and red is on. I think it ok. If it not on, you will try first choice.
- Press both softkey ,power switch, soft reset to start bootloader at the same time. Don't press power switch at first.
I think it can be open your device on to bootloader. Flash it again.
Click to expand...
Click to collapse
This solution worked for me today! my rw6815 was just like yours!
nhocbanme said:
Try this way :
- Take out miniSD card.
- Press both softkey and remove battery then put it back again (Don't unpress two softkeys) then softreset...
- Wait 2-3 secords
If it appear HP Bootloader Screen, your device not dead. You can flash it again.
Click to expand...
Click to collapse
You're Master!!!
help
my device is HP Ipaq rw6828.... i have this problems twice, but ican solve it, now i had a same problem.... now i can't resolve it....
now my device still (dead) only LED indicator when i charge it...... i use anything method, but it's not work.... except JTAG, cz i can't use this method.... please, any other way except JTAG mode????????? many big thanks.................. if u have an opinion, email me, [email protected]
help
Exclamation help
my device is HP Ipaq rw6828.... i have this problems twice, but ican solve it, now i had a same problem.... now i can't resolve it....
now my device still (dead) only LED indicator when i charge it...... i use anything method, but it's not work.... except JTAG, cz i can't use this method.... please, any other way except JTAG mode????????? many big thanks.................. if u have an opinion, email me, [email protected]
I have a hd2 with blutopia n supersports rom and today has been 1 helluva messed up day seriously !( I cant think straight) its all because my phone wont work. the phone was working beautifully with android on it and out of nowhere today the screen is not responding AT ALL. its so frustrating cant make a call cant read my txts.can some 1 please just tell me what i have to do so i can get a replacement? I put hspl3 and bluetopia android and supersports rom....please tell me what rom do i need to flash to it,do i have to relock/remove hspl3? thanks if u can help me out i just cant think clearly right now
turn off phone, hold down on the up and down volume button by pressing in middle while u toutch the end key..the red key.. after it boots press volum up to redo phone... if that does not fix it.. reflash with original rom
carl1961 said:
turn off phone, hold down on the up and down volume button by pressing in middle while u toutch the end key..the red key.. after it boots press volum up to redo phone... if that does not fix it.. reflash with original rom
Click to expand...
Click to collapse
what about hspl3???? what do i have to do so i can send it back without tmobile asking me why is there a custom rom and hspl3 on ur phone
ihateu said:
what about hspl3????
Click to expand...
Click to collapse
will be replaced when you flash original rom
djcedric said:
will be replaced when you flash original rom
Click to expand...
Click to collapse
ok how can i get the original rom... i cant get it from tmobile website because it wants a mei # and i cant get to it on my phone cause the screen is not working
open your phone up. take the battery off. The IMEI should be there along with serial number. Good luck
Touchscreen problem
Yesterday I start with a similar problem.
Using several Android builds on the same stock memory card.
The touchscreen stops responding always when I try to
reboot or turn off the phone, the same on all Android builds
and on WinMO. But locking the phone brings the touchscreen
back to life. Then I am able to unlock the phone and the
touchscreen keeps working OK.
Will try flashing the updated stock ROM.
you run hspl3 again , but select the other option with the extra.oooo, 208.000 , by default hspl3 installs the one to allow roms to work,,, when you rerun hspl3 select the other to set back to original so you can send back to factory anfter u install the t-mobile original rom
best to read this
http://forum.xda-developers.com/showthread.php?t=653614
phone won't turn on, no flash mode,
i ve galaxy ace
i surfing on wi=fi n suddenly phn switch off n wont start bak
wt to do
plz help . .
It's the wifi sod. Long press the power button (around 5-10 seconds) until you see the screen boots.
ananddugad said:
phone won't turn on, no flash mode,
i ve galaxy ace
i surfing on wi=fi n suddenly phn switch off n wont start bak
wt to do
plz help . .
Click to expand...
Click to collapse
Hey, you'll get warning because of this (doing the same 2 threads in two differents sub-forums).
Did you try the answers in http://forum.xda-developers.com/showthread.php?t=1215050 ?
Tell us your results. Maybe it is really a sod. Have you removed the battery and then put it on, and try to turn it on?
i tried everything but still no result mate
I want you to try something which I tried in similar situation: It worked me not sure whether it will work for you or not.
Take out SIM card and Battery for a min and then put just bttery back first and switch on Mobile. IF it starts then once its started put SIM card in.
kehur said:
I want you to try something which I tried in similar situation: It worked me not sure whether it will work for you or not.
Take out SIM card and Battery for a min and then put just bttery back first and switch on Mobile. IF it starts then once its started put SIM card in.
Click to expand...
Click to collapse
i tried this bt nt wrking
i submitted phn in service centre