hi all, help me to back up my roms plzzzz
my ori rom is
Rom v 1.03 USA
n bootloader mode v 1.02
i wanna upgrade to wm2k3SE
but i cant back up my rom ?
if i wan to back up always pop up notice
Card initialize is failed ??
wat thats means ?
thzzz for ur anssss
While a lot has been written, the following should provide an easy-to-follow guide:
Preparation:
1. A torch (read on and you will know why)
2. 256M SD card
3. Download ntrw.exe, romupdate.exe, hexedfull.exe from the ftp of this forum to c:\ and install hex editor
4. Download the appropriate ROM file (hereafter referred to as "newrom.nb1"). Somehow, these rom files seemed to be deleted from this ftp. I will upload them later.
5. Cancel USB in ActiveSync
6. Use Sprite Backup to backup your ppc
Backup original ROM:
1. Put ppc into the boot loader mode (hold both on/off and camera buttons at the same time while resetting).
2. Insert empty SD card.
3. Connect ppc to pc through USB.
4. Run romupdate.exe on pc.
5. Select “\\.\WCEUSBSH001” in port settings. In the popup windows, enter “d2s” and press enter.
6. Don’t get panic to see the ppc screen goes dark. Use your torch and you will see the download percentage. Wait until it reaches 100% and shows “CheckSum is OK!”.
7. Insert SD card into card reader of the pc. Ignore the “format SD card” message and click “No”.
8. Run “command” to go into DOS prompt and change to root directory (cd c:\). Enter “ntrw read oldrom.nb1 s:” where s is the drive of your SD card.
9. Ignore the “Data error <cyclic redundancy check>” message. You should save another copy of this important rom file “oldrom.nb1”.
Change header of newrom.nb1:
1. Right click on oldrom.nb1 to open hex editor. Copy the first 220 bytes.
2. Open the downloaded newrom.nb1 file and overwrite the first 220 bytes with those of the old rom.
3. Save the edited newrom.nb1. You may save another copy of this important file.
4. Go to the command prompt and enter “ntrw write newrom.nb1 s:” to write it to the SD card. Ignore the error message “The parameter is incorrect”.
Update the ROM:
1. Insert SD card into ppc and put it to boot loader mode again (on/off + camera + reset). Use you torch to check the dark screen.
2. When it shows “Press Power to flash”, press the on/off button. Wait until it reaches 100% and ignore the message “Download Fail - CheckSum Fail”
3. Soft reset your ppc.
4. You may have to reinstall your software, unless you are familiar with the advanced features of Sprite Backup.
or u can find at http://forum.xda-developers.com/viewtopic.php?t=19500&highlight=rom+backup
thanks to talent and all XDA Dev
Phreakazoidz
1. Download the 20060426 from www.seeo2.com
2. Run DSUU, after extracting the files in directory windows\temp DO NOT CLICK NEXT
3. Copy all 6 files into temporary or another directory
4. From that 6 files, copy 2 files with the extention nb0 (diskimage_ver.nb0 and eboot.nb0) to your mini SD
5. After copying into your mini SD, rename diskimage_ver.nb0 into diskimg.nb0
6. Now, you can run bootloader by pressing camera and soft reset ( you have to put your mini SD into your Atom so that the bootloader will boot from mini SD
7. Just wait and if there is some error message do not bother them, the most important that downloading OS Image and Eboot
8. After that your screen will blank, do not worry or panic
9. Pull out your mini SD and connect USB to PC and run bootloader again
( please make sure that your usb already connected to pc )
10. Now u can normally run the 20060426
This topic has been posted in many threads, there is no need to use the SD if this procedure is not done correctly you will loose the bootloader all together. Instead use the method posted by Luchao:
1.run atom 0416 rom update program, after the DSUU program extracted the files, don't click "next", go to windows/temp folder, copy those files extracted, except "diskimage_Ver.nb0" and "ExtendedRom.img", then save them somewhere else.
2.run july exec rom update program, after the DSUU program extract the files, don't click "next," go to windows/temp folder, overwrite with the files you just saved, this will leave only the diskimage_Ver.nb0 & ExtendedRom.img files as of the july exec rom, others become atom rom files, including an older bootloader which allows you to flash back other roms.
3. flash
http://forum.xda-developers.com/viewtopic.php?t=52925&postdays=0&postorder=asc&start=150
i just saw eboot.nbo & test.zip file in windows/temp/ folder, how to get the others file ? Thanks.
activesync mode not working
i tried the activesync mode, but not working.
finally i used bootloader method. just copied eboot.nb0 file to your miniSD. and enter bootloader mode.
Re: activesync mode not working
klikman said:
i tried the activesync mode, but not working.
finally i used bootloader method. just copied eboot.nb0 file to your miniSD. and enter bootloader mode.
Click to expand...
Click to collapse
bro, just klik next one more time, and DSUU will extract the others files
tjs0509, I tried your sd card method and totally lost the bootloader when I tried camera and soft reset. Is there anyway to bring back the bootloader?
interesting methods...
thanks!
"Camera" + SR, connect USB, run Device Software Update Utility, flash...
dear
tjs0509
I Downloaded the 20060426 from www.seeo2.com
2. Run DSUU, after extracted the files in directory windows\temp DO NOT CLICK NEXT
3. I Copied all 6 files into temporary or another directory
4. copied 2 files with the extention nb0 (diskimage_ver.nb0 and eboot.nb0) to your mini SD
5. After copying into your mini SD, renamed diskimage_ver.nb0 into diskimg.nb0
6. Now, I maked bootloader by pressing camera and soft reset ( I had to put my mini SD into your Atom so that the bootloader boot from mini SD
(from 1 to 100 dowloded)
7. I seem and if there is some error message do not bother them, the most important that downloading OS Image and Eboot
8. After that My screen was blank,
9. I Pulled out my mini SD and connect USB my pc . After I waited since 2 hour .screen been Black.. black... Black..I tried soft reset .and batery out -in but not anythink .
I was worring .!!??
Can help me What can I do?
Homer285, any help. I really lost the bootloader in the SD card method. I tried to connect USB and the 0721 ATOM EXEC recognize the ATOM, but when downloading the ROM, the ATOM just rebooted. I cannot press camera and reset to go to bootloader mode. Is bootloader mode be activated by a program in SD card so that it can be run in the explorer. Please help.
tjs0509 said:
1. Download the 20060426 from www.seeo2.com
2. Run DSUU, after extracting the files in directory windows\temp DO NOT CLICK NEXT
3. Copy all 6 files into temporary or another directory
4. From that 6 files, copy 2 files with the extention nb0 (diskimage_ver.nb0 and eboot.nb0) to your mini SD
5. After copying into your mini SD, rename diskimage_ver.nb0 into diskimg.nb0
6. Now, you can run bootloader by pressing camera and soft reset ( you have to put your mini SD into your Atom so that the bootloader will boot from mini SD
7. Just wait and if there is some error message do not bother them, the most important that downloading OS Image and Eboot
8. After that your screen will blank, do not worry or panic
9. Pull out your mini SD and connect USB to PC and run bootloader again
( please make sure that your usb already connected to pc )
10. Now u can normally run the 20060426
Click to expand...
Click to collapse
this method broke my bootloader too. i spent about RM200 to repair my bootloader...grrr
tangjunhu said:
You don't need cut any byte to flash into device,
just download temp.rar & diskimage_ver to do.
step:
1. unzip temp.rar to c:\windows\temp
2. enter engineering mode for HP68x8
3. excute c:\windows\temp\Device Software Update Utility.exe
4. delete all file except .exe and ROM file when show "NEXT" dialog.
that it can not update Eboot, so you don't wrong upgrade fail, if so you can re-upgrade. Eboot same like PC's BIOS. and ROM same like PC's OS.
5. click "next" to upgrade ROM until sucessful.
Click to expand...
Click to collapse
i can't not delete all file except .exe and ROM file when show "NEXT" dialog.
my pda show all bootloader.
tangjunhu said:
You don't need cut any byte to flash into device,
just download temp.rar & diskimage_ver to do.
step:
1. unzip temp.rar to c:\windows\temp
2. enter engineering mode for HP68x8
3. excute c:\windows\temp\Device Software Update Utility.exe
4. delete all file except .exe and ROM file when show "NEXT" dialog.
that it can not update Eboot, so you don't wrong upgrade fail, if so you can re-upgrade. Eboot same like PC's BIOS. and ROM same like PC's OS.
5. click "next" to upgrade ROM until sucessful.
Click to expand...
Click to collapse
i can't not delete all file except .exe and ROM file when show "NEXT" dialog.
my pda to remain bootloader
I need help with installing an OEM AT&T rom to my phone. My usb gave out on it and I need to return it to the store. The only thing is that the file that I have is an EXE file. can I put that on my memory card and run it just like that or do I need to do it another way?
and yes I did search but nothing came up. Only stuff on how to flash it in non .exe file
Open the .exe with winrar, extract the .nbh file inside, rename it to RAPHIMG.NBH and place it on the root directory of a microsd card (which must be formatted as FAT32)
hold volume down, press the soft reset button w/stylus
should bring up 3 color screen and prompt you to flash
Thank you very much Da_G. Worked perfect and am now the proud owner of a new HTC Fuze.
Da_G said:
Open the .exe with winrar, extract the .nbh file inside, rename it to RAPHIMG.NBH and place it on the root directory of a microsd card (which must be formatted as FAT32)
hold volume down, press the soft reset button w/stylus
should bring up 3 color screen and prompt you to flash
Click to expand...
Click to collapse
I did the same thing another way I guess I should share it with you as well. I put the phone into bootloader mode by holding the power button and volume down as I turned the Fuze on. Then I connected my phone to the computer via usb and ran the exe... It worked like a charm!