Related
Ok...I have been through all the posts about upgrading etc. I still have a problem and I'm sure that I'm overlooking something....but I can't figure it out on my own. Here is what is happening (it does the same thing with every RUU that I've used...the DST fix...upgrading to WM6....etc)
1. I run the RUU and let it go through its routine (extract files, verify info on pc, etc.)
2. I check the box that says I have read the readme and click next
3. The next screen appears and it has the following steps:
Connect to the USB cable (check)
Establish an ActiveSync Connection (check)
Disable standby and hibernation on PC (check)
Make sure batter is > 50% (check)
Then I check the box and click next
4. I pick the update and click on the update button
5. I verify that I want to upgrade my phone from ROM verion x.xx.xxx to x.xx.xxx and click next
6. The program tells me that I am finally ready to update...and if I am sure I want to proceed to click next...so I click next
7. As soon as I click next...the progress bar comes up on my pc and my phone goes into standby mode (no bootloader...just standby). The progress bar never moves.
8. After a minute or two the RUU give me the ERROR [260]: Connection
9. I reboot my device and repeat steps 1-8
10. I reboot my device and my computer and repeat steps 1 - 8.
Now if I leave my device connected to the usb and close out the RUU after it gives me the ERROR [260], and then run the RUU again...when it is first verifying the information on my pc (before it asks any questions and before it tells me to connect my device) it will throw the device into bootloader mode. If I try to keep running the RUU while the device is in bootloader mode it give me the error that my device is not connected. I have tried and tried...maybe one of ya'll can help me. Thanks in advance
Chris
Some questions:
.) Is your desktop PC running XP or Vista?
If you have a firewall running, close it.
.) If you running Vista check this guide:
http://www.mrvanx.org/cms/index.php?option=com_content&task=view&id=23&Itemid=27
.) What updates did you try to flash?
.) Did you install Olipros bootloader first?
gerald_s said:
Some questions:
.) Is your desktop PC running XP or Vista?
If you have a firewall running, close it.
.) If you running Vista check this guide:
http://www.mrvanx.org/cms/index.php?option=com_content&task=view&id=23&Itemid=27
.) What updates did you try to flash?
.) Did you install Olipros bootloader first?
Click to expand...
Click to collapse
XP
No firewall
I tried to flash the WM6 from AT&T I assume its beta
and no did not install the Olipros bootloader
Ok...I think I found out how to do this...Ya'll can tell me if I'm screwing something up.
I go through all the steps listed above until it gets to the progress screen. When it gets there I manually put the the device in bootloader mode (Power, side ok, and reset). Once I do this...the progress bar starts moving. I will let you know if this works...
Hmmmm
Its not the way it should work but if it works its ok
You should have installed Olipros HardSPL first and then try to flash an official rom. If its working then something with your download is wrong.
What ROM is on there now?
Has the phone been CID unlocked?
Oli's CustomRUU is better, you may want to unpack the ROM and put the NBH in a folder with Oli's RUU and then do the upgrade.
BTW, gerald_s is right, you should not have to do that... what you may want to do is put the phone in Bootloader mode manually (while not connected to the PC), then plug in the USB, then start the RUU. That helps some people with 260 error.
I've got the same damn issue... it's driving me crazy. I had this occur when I flashed my Hermes100 from the stock version to Custel's. After about 15 starts and reboots it took. I'm now trying to get to Vp3G's 3.60 and it continues to give me the 260 error.
I am trying to figure out how to fomat my micro, but really hoping to find a solution over cable.
Hermes 100
IPL 1.04
SPL - 2.10 Olipro
Any suggestions?
You may be trying to flash a rom that includes the radio rom. What is your device? Is it possible that your device is a new x01ht with radio 1.14 and radio bootloader 0182? If yes, then you will get this error when you try to flash a rom with this method because during the flash it will be disconnected by the radio bootloader because it is not overwriteable. If you flash using the NBH file on the microSD, it will skip past radio and radio boot and just flash the other parts of the file.
mikebraeuer said:
I've got the same damn issue... it's driving me crazy. I had this occur when I flashed my Hermes100 from the stock version to Custel's. After about 15 starts and reboots it took. I'm now trying to get to Vp3G's 3.60 and it continues to give me the 260 error.
I am trying to figure out how to fomat my micro, but really hoping to find a solution over cable.
Hermes 100
IPL 1.04
SPL - 2.10 Olipro
Any suggestions?
Click to expand...
Click to collapse
If you are running windows XP, just connect the card to the computer, open MY COMPUTER, right-click the removable disk that is your microSD and then click format. Default in windows xp is to format using FAT32 filesystem which is perfect.
The thing is... if you dont know how to format a drive in Windows, should you be flashing your device yourself?
Which Solution???
I've got a Softbank X01HT with:
S/N: HT639
SuperCID <--- result of checking by mtty
IPL: 1.04
SPL: 2.10Olipro
GSM: 1.47.00.10
OS: 3.54.07 WWE
I tried to flash with new Schap 3.54c but the process would not be done coz ERROR 262 or ERROR 302. Fortunately, after failure of flashing, my device is still normal running. Then I tried to flash radio 1.51.00.10 but I got the same above. Once again, I have just tried to flash splash screen and I got the same result too. It mean my device can not upgrade anything !
Anybody here show me a solution that help my device to become a normal device, I mean it will be able to flash anything ROM as it would be! Don't tell me READ and READ, I had read so much . And don't tell me use MTTY again SPL1.01MFG, I think that is a final solution
Wantoknow said:
I've got a Softbank X01HT with:
S/N: HT639
SuperCID <--- result of checking by mtty
IPL: 1.04
SPL: 2.10Olipro
GSM: 1.47.00.10
OS: 3.54.07 WWE
I tried to flash with new Schap 3.54c but the process would not be done coz ERROR 262 or ERROR 302. Fortunately, after failure of flashing, my device is still normal running. Then I tried to flash radio 1.51.00.10 but I got the same above. Once again, I have just tried to flash splash screen and I got the same result too. It mean my device can not upgrade anything !
Anybody here show me a solution that help my device to become a normal device, I mean it will be able to flash anything ROM as it would be! Don't tell me READ and READ, I had read so much . And don't tell me use MTTY again SPL1.01MFG, I think that is a final solution
Click to expand...
Click to collapse
Have you tried flashing with your microSD?
Kevbodian said:
Have you tried flashing with your microSD?
Click to expand...
Click to collapse
I forgot to tell that, I had flashed through extra memory card yet, and could be done!
But I wanna flash ROM against CustomRUU through MS Active Sync as I had used before. Can you help me
i have a problem very similar to Chris. when i check the box "yes activesync is syncronised", and then the progressbar shows up and the phone goes into standby.
i've turned standby of in powermanagement options.
my os is XP
i use active sync v4.5
and this is first time i try this.
i've read something about this bootloader, i can get there but then i cannot sync with active sync. so i kinda stuck.
have been searching the forums and this was the same problem as mine but i don't understand your solutions.
//KufrA
--Problem solved--
i did all things without activesync,
1. start phone in bootloader
2. do the install
3. wait 0% to 100%, and done.
is there a problem with active sync or why do i have to do anything with it at all?
i am following mr vanx guide found here:
http://www.mrvanx.org/cms/index.php?option=com_content&task=view&id=59&Itemid=27
to downgrade my device to SPL1.06 and IPL1.01 using file HERM_SPL1.06_Only_CustomRUU.rar
however, once i flash my device, it lists that I have SPL1.06 and IPL1.00, not 1.01. I have tried the flash using 'SPL-1.04/1.10 - SPL - 1.09 Bootloader' and also 'Force using SSPL' with no luck.I am running a hermes 100 but I still have WM6. i just thought about this, but do i need to downgrade to a signed cingular/att signed ROM before this will work? I need to be running IPL1.01..any help or ideas please?
*edit*
now the device boots and connects toactivesync fine, but when i try to flash a radio rom, WM rom, ipl/spl update (2.10, 1.06 doesnt matter) the device reverts to the tri-color screen after verifying the information on your hermes, but then is not able to update. it is saying that the connnection can be made to my device, is this because of ipl 1.00??? please help!!!
**LATEST**
ok the problem now is that it willnot update anything anymore... as i try the update process the phone goes into the bootloader mode and shows
HERM100
IPL-1.00
HERM100
SPL-1.06
while the computers says 'verifying the information on your device.' I have tried complete packages such as 'RUU_Hermes_CINGULAR_WWE_3.62.502.3_6275_1.54.07.00_108_UOOS_SVN05_Ship.exe', and also packages with seperate ruu wrapper such as what is found in 'Hard-SPL-V7.zip.' I donot know why the update process freezes at this step...please this is really killing me.
chapter 2
moving on... I found the 'fix' for this in the wiki, however when using the 'mtty.exe' file it says to "select USB" from the dialog box but I cannot get an option for anything else except COM 1-4 in the diag box... what do i need to do to enable the USB option???? and yes i disabled activesync like it says obviously.
its like the device cannot be recognized by usb while [the device is] not actually running windows... argh!!!!
Sometimes you need to restart your hermes and than run the mtty.exe.
Hi,
I have a big problem.
Sorry, but i already search in this forum but no success.
I upgraded a ATH100 with a SPL 3.65 ATH400 Rom
Now, i try to back to ATH100 but i cant. With PC and RomUtility, i get MODEL ID 244 error.
With SDCard i get 00058002 error while Loading...
Anybody can help me.?
Thanks
athena400back to 100
i was in too, now if you cant downgrade yet,sent me an Email ,to [email protected] and sending to me alot of pic from thet and information about your rom.
hi guys,
I had the same issue too....can not flash from SD card with 00058002 loading ...
any solution yet ??
hi guys,
I had the same issue too....can not flash from SD card with 00058002 loading ...
any solution yet ??
I have same problem. Please anybody can help me?
Try out This>>>>>
ERROR [244] : INVALID MODEL ID
from cmonex @xda-dev
This is good for both corrupt modelid and corrupt wifi, and fixes both at the same time.
STEP BY STEP:
1. download attachment at the end of the post for mac1.exe (requires .net 2.0 installed on the PC)
2. you will also need to download the other attachment in this post for the mtty program.
3. enter bootloader (tricolour screen) manually by pressing and holding camera button all the way in (yes I mean that, press it in as hard as you can!!), while doing a reset, then keep the camera button held until you see the tricolour screen.
4. disable USB in activesync (wmdc if you have vista - in this case, do not kill wmdc, just disable usb in it!!!)
5. run mtty and select USB option from the dropdown box!
6. then press enter in main window that comes up, see if that gives you Cmd>
7. now you should have Cmd>, if not, re-check if you did the above steps right until you get Cmd>
8. now run the mac1.exe, type in your MAC address you want to use for the Athena, if you have SPL 3.xx reported on the tricolour screen, then use the button for SPL 3.xx, otherwise if you have SPL 1.xx reported, use button for 1.xx.
9. this should have generated a .bin file for you, copy that bin file in the folder of mtty.
10. now, in mtty, type (do not copypaste!) this command: task 32
11. this should return Level = 0
12. now, you must only do one of the two following commands:
- if you have SPL 3.xx, then type (do not copypaste!!) this command: lnb filename.bin 76508000
(there filename is the name of the .bin file you generated - don't forget to put .bin after filename, as the full name is needed).
- OR, if you have SPL 1.xx, then the command is different (do not copypaste!!): lnbs filename.bin 75108000
(there filename is the name of the .bin file you generated - don't forget to put .bin after filename, as the full name is needed).
NOTE, the command starts with a lowercase "L", not "I"!
WARNING: PLEASE DO NOT MIX UP THESE TWO DIFFERENT COMMANDS!!!
if this info helps: most people will have SPL 3.xx, and if you have AP4 (not vanilla) already running then you're definitely 3.xx
13. mtty will popup a window asking "OK", you press OK!
if you get "Fail to synchronize with the host (1)", then make sure you did follow step by step. if still same error, try placing mtty and the bin file under C:\.
14. now the file downloads, if mtty reports it flashed the file, and at the end "code entrypoint unknown", then that's it, now boot back to WM and see if wifi works.
Download: Mac1.zip mtty_0513_Test.zip
But where atachment ?
For me....WORK...THANKS again CMONEX
but i not do to repair wifi i want to flash my wm........
help me please ,,,
i make hard spl for athe400 in athe100
"ERROR [244] : INVALID MODEL ID
from cmonex @xda-dev
This is good for both corrupt modelid and corrupt wifi, and fixes both at the same time"
as it says it fixes corrupt modelid
It is worth a try
ERROR[244] :Invalid model ID ATHE100
Hi,where do i find the MAC adress for my ATHE100 as i cannot get forward from the bootloader?I am using SPL-v1.20.Olipro.Thanks to any1.
Yes, where is the MAC ADDR
As above, would be grateful if anyone would help us find where the MAC address and thanks for this thread this is the bane of most new owners and newbies. Cheers!!
Mac addr found, but......
Yes found the MAC address - it's under the battery cover, but having gone thru the whole process I got the following 3 errors at the end-
ERROR: no header matched
Transfer CERT error
Flash Programming Error
Thanx buddies!
3 ERROR Messages!!!
Hi Lakeman, could you help decipher these mysterious errors which I had after I have gone through the process twice
ERROR: no header matched
Transfer CERT error
Flash Programming Error
Thank you!
invalid Command
command error
whats wrong???
Cmd>lnb ameo.bin 76508000
lnb ameo.bin 76508000
Command error !!!
here you go >> http://xacsx.de
german ameo-site, roms, repair, and other helpful things
command error
whats wrong???
Cmd>lnb ameo.bin 76508000
lnb ameo.bin 76508000
Command error !!!
if you get notice
-> ERROR [242] : INVALID LANGUAGE
-> ERROR [244] : INVALID MODEL ID
-> ERROR [294] : INVALID VENDER ID
-> ERROR [296] : UPGRADE ONLY
One of these error messages will appear when you use the wrong RUU to do the upgrade. RUU will check if the Model ID and Language ID are compatible with the device. Make sure you use the appropriate RUU tool to upgrade.
stuck in bootloader. Help needed.
I have a HTC Athena x7500.
accidentally upgraded my htc x7500 WITH SSPL-Manual-x7510.zip of HTC X7510
Wend I turn on the device, it goes directly to bootloader and
the screen is:
ATHE 100
IPL - v1.00
ATHE 100
SPL-v3.05.0000 OR my old spl is 1.10.0000
I have tried to change the language of my athena and then he died :spanish > fransh
USB (wend is to connect)
series (wend is unconnectable).
I can not turn the unit off by pressing the button, but must take
the battery.
I have tried with hardspl its not working
I want a solution in the forum xda-develop it says my q must upgrade to the rom of espana oficial
After downloading the rom:Advantage_HTC_SPA_2.21.412.1_1.50.00.00_Ship
I tried to upgrade to this rom May j has a mesage on my athena screen:
found spl v1.10
dowload Spl before v3.05 is not allowed!
I tried to update it with the sd card i have the same mesage
upgrade with athenaUnlucker not work
upgrade with hardspl v7 not work
upgrade with CheetahUnlocker not work
upgrade with athena wraper not work
I have explored ruu_signeg.nbh in spanish rom with notepad jai entered the signer spl 1.10 I know if is sure or not
I believe there is a problem in the image rom saved in my athena rom
what I see on the screen of my athena is the spl 3.05.0000
The real spl is 1.10.0000 there is confusion in my spl
with mtty : task 32 level=ff
is what I can fix this problem with mtty
so if possible please guide me
I board on my pda (cid locked)on the Spanish language HTC_304
sorry for my bad Englis
thank you in advance
My email: [email protected]
http://forum.xda-developers.com/showpost.php?p=5205291&postcount=8
I think there is another thread somewhere about this but you could try the incorrect ID fix in the post above
and try to do the lower SPL
well, Hard-SPL is released now! sorry for delay, I got distracted elsewhere
[size=+2]NOTE: This is NOT a SIM unlocker - it also doesn't unlock Security for other radios. if you need that, GO HERE[/size]
[size=+2]Donations are always appreciated to the big link in our signature ("elite project"). You can also donate via the link offered in the new Hard-SPL program. Thank you!![/size]
Preparations:
first an important note, if you want to flash more than one Iolite, contact cmonex for additional licenses via http://support.htc-unlocks.com. (the first license is transparently granted and free, so normal users do not need to worry.)
0) this package is for Iolite (Touch Cruise II/2009) devices. for any IOLI***** so far (SSPL loader checks this and gives a warning if needed), afaik there is no CDMA version so all the model variations should be fine.
1) if you have vista, WMDC update is recommended: http://www.microsoft.com/windowsmobile/en-us/help/synchronize/device-center.mspx
Instructions:
read this if unsure how to install Hard-SPL...
1) download latest Hard-SPL package (currently v1.10) from attachment, extract to an empty folder.
2) you must Have Phone Synced with PC in Windows Mobile!!!
3) NEW: internet access is required as the program checks online for updates and license.
4) run Iolite-Hard-SPL EXE on PC, make sure it's launched from a local drive (not through network drive, etc.). if you are on vista, launching as Administrator is strongly recommended, on XP administrator login is required. important: if your AV (norton/symantec mainly) warns about a virus, ignore it, it just doesn't like the packer I used to pack the program.
5) if possible, always use Automatic flash mode (for uses of Manual mode, see troubleshooting section)
6) it will ask you to wait while it prepares for the flashing, press OK. follow steps in the program and then in the RUU.
7) some notes: it should go through without any error messages, if one does pop up, then please follow the instructions included in the error text. if no specific instruction is shown, then ask for help in the thread, but this should not ever occur (as this means a really fatal error occurred).
more notes: when RUU says it will hard reset, do not worry, it is not going to do that. also when it says the flash will take 10 minutes, ignore that, it will only take a minute or so.
8) device should go to a tricolour screen now that says 1.09.C-SSPL, this is the SSPL version, which is temporary.
9) SPL flashes, device automatically reboots, job done.
10) to confirm you got it installed, go into bootloader mode (tricolour screen!) and verify the screen shows 1.09.OliNex, which is the Hard-SPL version.
NOTE: you will not see the SPL version during normal boot, that is the OS version, not SPL!
to enter SPL to check version, fully power the device off by long press of power key, then power on while holding the "volume down" key on the left side of the device. keep holding the volume down key until you see tricolour screen which is the bootloader mode, then release it.
NOTE 2: this is unsigned Hard-SPL. no limitations on flashing ROMs or radio packages. also, this has overwrite protection against HTC RUU's overwriting HSPL with a stock one, so if someone needs to revert to stock SPL for warranty reasons, a stock SPL downgrade package will soon be posted in this post as well. use this relocker *only* if you need to return the phone for warranty, and only use it as last step - after reflashing stock OS and radio. see steps at the end of this post about how to reflash stock SPL.
NOTE 3: do not use this RUU for anything other than SPL flashing (i.e. hardspl or stock spl restore)!!! nothing other than SPL's made by Olinex team (using OliNex custom cert, which is not public) will flash to make SSPL more secure. if you want to flash some other rom, then use shipped RUU or customRUU if you need to flash cooked ROM.
Troubleshooting:
- read the instructions above.
- read the instructions above.
- read the instructions above.
Manual flash mode for USB issues: you should usually go for Automatic flash mode; you must only attempt the Manual mode option if Automatic flash mode or SSPL-Manual.exe already put device in SSPL tricolour screen and you got USB issues. any other errors triggered while running in Autoflash mode will have to be fixed as instructed in the error message.
ModelID checking:
- afaik no CDMA model, so doesn't matter but let me know if you got any problems.
nothing happens on the device, does not enter tricolour screen mode:
- anyone having problems with the device entering SSPL automatically, please make sure you watch the device screen if it asks about running files. also try unchecking advanced usb functionality in settings.
- if it crashes instead of entering SSPL, you need to use Automatic mode.
general usb connection error problems if you get connection error in RUU after the device goes to 1.09.C-SSPL screen:
- try manual SSPL: copy SSPL-Manual-Iolite exe to the device and run it, then when it went to 1.09.C-SSPL tricolour screen and shows "USB" at the bottom in this screen, use Manual option in the Hard-SPL program on the PC.
- make sure device was still synced via USB to the PC at the point of it entering SSPL (the 1.09.C-SSPL screen)!
- try a different USB port
- try different USB cable
- do not touch USB cable during the process especially if it is already a bit dodgy
- also do not use USB hub
- you can also try rebooting your PC
- and you can try using another PC.
- also you can try unticking advanced network functionality in start menu / settings / connections / usbtopc applet.
- another reason for USB connection error: if your PC takes too long to load the drivers (if your device is in bootloader for the first time and perhaps if you are on vista), then if RUU times out, but device still says "USB" on the tricolour screen, just leave it there and re-run the RUU when driver installation finishes.
- finally, you can try disabling antivirus or firewall programs on the PC.
other issues:
- if Enterbootloader.exe fails to run (says missing component or similar), try a hard reset of the device.
- if device reboots instead of going to SSPL screen (1.09.C-SSPL), contact us by PM'ing cmonex. do not PM OliNex user, that is not monitored frequently.
How to reflash Stock/Shipped SPL - STEP BY STEP - FOR WARRANTY REASONS ONLY!:
0. please make sure you already flashed stock ROM and radio, because stock SPL flash is *always* the last step before sending the device in.
1. take the SPL relocker attachment, and run the EXE - this will flash 1.09.0000 stock SPL. simple as that!
2. flash
3. verify if it flashed by checking version in tricolour screen, it should say 1.09.0000.
credits:
first, "OliNex" is a team which means: cmonex + Olipro
Olipro -> EXE program concept that runs on the PC, Hard-SPL concept, server code, maintaining licenses
cmonex -> new PC EXE & SSPL loader for windows mobile and SSPL binary. Hard-SPL binary. (SSPL loader: partially based on haret and old pof&Olipro jumpspl code)
---reserved post---
---reserved---
"IOLI100
SPL-1.09.oliNex
MicroP-Iolite(LED) v5"?
Has it released? It has appeared on the interenet.
Let me see see!
chenjun_conan said:
"IOLI100
SPL-1.09.oliNex
MicroP-Iolite(LED) v5"?
Has it released? It has appeared on the interenet.
Click to expand...
Click to collapse
yes, I've sent it to several people. I'm posting it here too in a sec.
edit: posted
Dan
OK
you are great.
Thank you so much.
Fantastish!
THANK U VERY VERY MUCH!!!
after HSPL and flashing to Rissian ROM it says "Your OS ROM isn' t customized for your hardware Please reflash the proper ROM code or contact the service center' .
In the internet i've read that taking out the battery for 10-15 minutes must help. But it doesn't. Please help!
Great job, big thanks!
@ cmonex was send you a PM, please answer me. Thanks!
Greetings
Baga12 said:
after HSPL and flashing to Rissian ROM it says "Your OS ROM isn' t customized for your hardware Please reflash the proper ROM code or contact the service center' .
In the internet i've read that taking out the battery for 10-15 minutes must help. But it doesn't. Please help!
Click to expand...
Click to collapse
try to flash WWE|Eng and post result here
Nice work as usual guys.
Thread stuck
Dave
After IoliteSPLRelocker, the HSPL' s not working, why? Please help
Thank you
Thank you so much for your hard work.
My Iolite can do do just about anything right now.
Baga12 said:
After IoliteSPLRelocker, the HSPL' s not working, why? Please help
Click to expand...
Click to collapse
You tell us? It what way doesn't it work?
Dave
I tried to test the IoliteSPLRelocker, it flashed correctly, then I again tried to flash the HSPL with mhile my device was in three color mode, but it stops at the 0%, not going more. Stupid of me, of course
So? what about WWE Roms? Does anybody flash them at new HSPL?
thanks very much . it's great'
Baga12 said:
I tried to test the IoliteSPLRelocker, it flashed correctly, then I again tried to flash the HSPL with mhile my device was in three color mode, but it stops at the 0%, not going more. Stupid of me, of course
Click to expand...
Click to collapse
Please help!
max_nya said:
So? what about WWE Roms? Does anybody flash them at new HSPL?
Click to expand...
Click to collapse
Once you have Hard SPL, you can flash any ROM's (Cooked or Shipped) to your device. So put on Hard SPL, find a WWE ROM and flash it .
Baga12 said:
Please help!
Click to expand...
Click to collapse
I've just checked the re-locked and it does contain the correct SPL.
Connect your phone to you PC using AS, and then run the re-locked, once done your SPL should be 1.09 (with the .OliNex) again
Dave
Hi, does anyone know how to enter the radio bootloader with mtty? I found some instructions on the net but they dont work, is there any special issue on the nike?
My nike has HardSPL 1.22, radio 1.65.xx and super cid unloked.
You need a MFG SPL which includes the command "rtask"
Do a "rtask a" and you can talk to radio (no echo), to return to SPL type "retuoR".
You can also security unlock your device and enter bootloader directly by pressing send and power on at the same time, or do "rtask a" followed by "setboot 1". Next time device boots up in radio bootloader.
You can then use my FrankenKaiser SPL bootloader for fast loading and booting a ram image. In my opinion a nice way to test Android
jockyw2001 said:
You need a MFG SPL which includes the command "rtask"
Do a "rtask a" and you can talk to radio (no echo), to return to SPL type "retuoR".
You can also security unlock your device and enter bootloader directly by pressing send and power on at the same time, or do "rtask a" followed by "setboot 1". Next time device boots up in radio bootloader.
You can then use my FrankenKaiser SPL bootloader for fast loading and booting a ram image. In my opinion a nice way to test Android
Click to expand...
Click to collapse
Thanks, now i have installed Hard-SPL1.15 MFG, the rtask a is now accepted, and like you said i have no echo... setboot works, but when i type in other commands like help, h, ?, gpio, version i get no outputs... What am i doing wrong? is it still the wrong SPL???
m0rph3us said:
Thanks, now i have installed Hard-SPL1.15 MFG, the rtask a is now accepted, and like you said i have no echo... setboot works, but when i type in other commands like help, h, ?, gpio, version i get no outputs... What am i doing wrong? is it still the wrong SPL???
Click to expand...
Click to collapse
You have a very limted command set if your device is not security unlocked. You find my security unlocker in one of the stickies ..
(then you have echo_on etc, enter a ? for more cmds)
Thank you, finally i get it to work... I have one last question, is there any command to get debugging log or something like that, to see whats going on when wm boots, just like the commands for the diamond?i tried set 1a 0, but it does not work, on the diamond it enables debugging information