After I flash the Original TG01 Chinese (HongKong) ROM to my Softbank X02T. It's deadEach time, I power-up the device, It's only have a green LED flash and vibrate a single time.
After, I connect the Pin 1 & 2 by a wire and adhesive tape fixed, it can power-up and complete the set-up process to show Chinese WM6.5 . The SIM card still need password to connect the network......(blame the SIM lock program...). I can find the SimlockP.exe under the \Windows\ folder, but this file cannot be delete due to it stay in ROM location.
However, I find a serious problem is that, my battery cannot be recharged!! Even the battery used up, it cannot charge automatically! I need to pull out the battery each time and charge externally.
In additions, the PINs (3 large and 1 small) under the SIM slot may be the tricks to "Lock the phone to the exact Mobile company". Our discovery is that:
i, Pin - 1 & 2 connected >> can awake the X02T and T01A using TG01 ROM
ii, Pin - 1 & 3 connected >> flash the ROM file at *.enc format
iii, Pin - 2 & 3 connected >> tried but the function is unknow.
iv, Pin - 1 & 4 connected >> tried but the function is unknow.
It may be one of the hints for unlocking the X02T and T01A. Needed to further research.
Could you flash T01A UK rom from mr.mike after your device alive?
My phone is T01A and still waiting for unlocking
Anyway it is a good news for dead TG01.
If you want to bypass the sim unlock screen, you should try any custom 6.5 rom (it never show that screen) . However, I don't know that whether X02T is compatible with custom rom or T01A custom rom (TG01>T01A tool).
vincentbingkau said:
After I flash the Original TG01 Chinese (HongKong) ROM to my Softbank X02T. It's deadEach time, I power-up the device, It's only have a green LED flash and vibrate a single time.
After, I connect the Pin 1 & 2 by a wire and adhesive tape fixed, it can power-up and complete the set-up process to show Chinese WM6.5 . The SIM card still need password to connect the network......(blame the SIM lock program...). I can find the SimlockP.exe under the \Windows\ folder, but this file cannot be delete due to it stay in ROM location.
However, I find a serious problem is that, my battery cannot be recharged!! Even the battery used up, it cannot charge automatically! I need to pull out the battery each time and charge externally.
In additions, the PINs (3 large and 1 small) under the SIM slot may be the tricks to "Lock the phone to the exact Mobile company". Our discovery is that:
i, Pin - 1 & 2 connected >> can awake the X02T and T01A using TG01 ROM
ii, Pin - 1 & 3 connected >> flash the ROM file at *.enc format
iii, Pin - 2 & 3 connected >> tried but the function is unknow.
iv, Pin - 1 & 4 connected >> tried but the function is unknow.
It may be one of the hints for unlocking the X02T and T01A. Needed to further research.
Click to expand...
Click to collapse
many thanks for your update
could you share more detailed inform about how to flash a TG01 rom on X02T?
One more question
Did flashing TG01 Rom to your X02T change the radio rom version?
Short PIN unbricking works only if bootloader is ok if You kill bootloader(it's easy to do) then even shorting pin's method won't work...
with simlock try making a 0b text file name it SimlockP.exe and copy it to windows folder using pocket commander or resco explorer(file explorer can't do this) and try but I'm not sure if replacing this file will unlock phone but should take out nag screen or lead You to HR
nico101 said:
Short PIN unbricking works only if bootloader is ok if You kill bootloader(it's easy to do) then even shorting pin's method won't work...
with simlock try making a 0b text file name it SimlockP.exe and copy it to windows folder using pocket commander or resco explorer(file explorer can't do this) and try but I'm not sure if replacing this file will unlock phone but should take out nag screen or lead You to HR
Click to expand...
Click to collapse
useless
in my rom i deleted simlock apps
and it's helpless with unlock
ffboy2009 said:
useless
in my rom i deleted simlock apps
and it's helpless with unlock
Click to expand...
Click to collapse
When it jumped out window "Phone is blocked. Enter password to disable SIM lock.", try to connect the phone with PC through ActiveSync. If success, you can kill the process "SIMUnlockP.exe" using a phone management tool, then the "...Enter password..." window disappeared and it get back to normal WM interface.
But it does not mean Docomo or Softbank sim lock is removed. If the Radio is 5005.1901.xx or 5005.1908.xx, the Docomo or Softbank sim lock is still there.
last night, I brick my X02T(Softbank) .......
Can show me how to alive T01A by short pin 1 and Pin2, share for me your ROM to do, thanks
Here's the details of my procedure to awake my Softbank X02T>>>
1. Download the TG01 ROM (my version is original Hongkong ROM)
2. Place in the microSD folder /prg and rename the .tsw to .enc
3. Short pin 1 & 3 and press power button around 10 sec,
4. It will start the screen "Downloading" and wait around 10mins, it reboot and "Bricked"
5. Then, cut a short, thin bare copper wire, connect the Pin 1 and 2 (location from left - pin1 & right is Pin 2), using adhesive tape to fix it.
6. Press the power button, the phone will wake-up then proceed to Windows setup screen.
For T01A, I think the tricks may very similar to X02T and pls have feedback if anyone tried above steps on T01A, the phone awake or not.
The further findings are that:-
- Using Resco-explore cannot delete the "SIMUnlockP.exe". Any other method in details?
- Ref. to member "cktp", I thinks the radio version is the same and cannot be changed by Rom flashing.
- When I insert back the Softbank SIM, it cannot "unlock" and still ask me to enter the password (I don't know why?).
- I guess that if we can change the "Radio firmware", it might be the most effective way to Unlock the SIM. (because we cannot find the password!)
For those X02T and T01A members, we work together and never give-up !!!! Cheers!
vincentbingkau said:
- When I insert back the Softbank SIM, it cannot "unlock" and still ask me to enter the password (I don't know why?).
My phone is T01A. In oringal Japanese WM6.1, no "enter password" request when insert non-Docomo sim. After flashing to cooked WM6.5, "enter password" window will jump out when WM system start. I can not use any function of the phone since no password.
I tried nico101's method, creating an empty file, name it SimlockP.exe and copy to Windows directory to replace the orginal one using resco explorer. It works, no "enter password" window, and I can use WM system but there is no network signal at all. That is, it disable the PHONE CALL funtion, the phone is not finding any network.
In my way, connecting phone to PC, and kill the process "simunlockP.exe", "enter password" window will disapper, and phone is still finding network.
But it's very strange when you use Softbank sim it still ask for password. Becase my T01A with cooked 6.5 will not reqest for passord entering when I use Docomo accepted sim.
Click to expand...
Click to collapse
Click to expand...
Click to collapse
Thank for help, but T01A still dead, I tried short pin 1&3, and short Pin1&2 nothing happen, just vibrate and green light, no dowload.
I want know, where you put those file TG01_SDDL.exe and TG01_SDDL+.exe
Can you share for me your file that you tried success
thanhchaua6 said:
Thank for help, but T01A still dead, I tried short pin 1&3, and short Pin1&2 nothing happen, just vibrate and green light, no dowload.
I want know, where you put those file TG01_SDDL.exe and TG01_SDDL+.exe
Can you share for me your file that you tried success
Click to expand...
Click to collapse
my x02T no vibrate,no green light
just like a brick
The Help
Mybee i can help,
1 - download the ROM_TG01_Clone_HD2_Tmous_rel.2 (best ROM),
2 - use the TG01toT01A Converter for make a *.tsd file
3 - rename the file.tsd to TG01WP.tsd
4 - copy to SD card in normal PRG folder.
5 - Pin and flash.
Always work to me.
Related
Antha Secure DEMO has locked my Mobile 6 Ameo!
--------------------------------------------------------------------------------
I really REALLY hope someone might be able to help me here.
I am rather upset at my stupidity.
I was looking for VPN software for PPC.....found this:
http://www.anthavpn.com/webmaker/portal/wmlink_490
But I managed to download the Antha Secure instead and istalled it without checking.
I will Never make same mistake....How I was so stupid (not enough coffee)
I reset my device expecting Cisco able VPN but I was presented with a lock screen (like windows lock ) asking for a password to access my device.
Below the password box is a note saying "password is: demo"
Password demo does not work I am crying.....I have locked my Device!
Unlock code is not my device unlock code
It wont let me make emergency calls or anything......
I am stuck looking at their splash screen...
I can connect via Active sync - I removed the program files relating to this but I cannot get it to stop starting up with my device....
In windows/startup I have:
btdwake
poulook
sddeamon
Anyone rescue me
PLEASE!!!
If you are able to connect with activesync. Can't you just flash your device with Windows Mobile 6 again? That should put you back to start.
Hope that helps
x75
did hard reset
Thanks for reply though......
yarod_g14 said:
Antha Secure DEMO has locked my Mobile 6 Ameo!
--------------------------------------------------------------------------------
I really REALLY hope someone might be able to help me here.
I am rather upset at my stupidity.
I was looking for VPN software for PPC.....found this:
http://www.anthavpn.com/webmaker/portal/wmlink_490
But I managed to download the Antha Secure instead and istalled it without checking.
I will Never make same mistake....How I was so stupid (not enough coffee)
I reset my device expecting Cisco able VPN but I was presented with a lock screen (like windows lock ) asking for a password to access my device.
Below the password box is a note saying "password is: demo"
Password demo does not work I am crying.....I have locked my Device!
Unlock code is not my device unlock code
It wont let me make emergency calls or anything......
I am stuck looking at their splash screen...
I can connect via Active sync - I removed the program files relating to this but I cannot get it to stop starting up with my device....
In windows/startup I have:
btdwake
poulook
sddeamon
Anyone rescue me
PLEASE!!!
Click to expand...
Click to collapse
Maybe someone has a better solution but here goes mine. Download and install Safe Mode for PocketPC. http://www.freewareppc.com/utilities/safemodeforpocketpc.shtml
Soft reset and try to go into safe mode to see if it'll allow you to uninstall. If you can get into the device, at the very least you may be able to edit your registry to disable this buggy software. Let us know how it goes.
It's weird that you can't uninstall the software via ActiveSync though.
Hard reset so sorted but....
Well, the app locks the device on startup. ASks for password (in box under says password : demo - this didnt work with soft keyboard hard keyboard upper and lower case etc...)
So Couldnt actually get to home page...
When I selected the item through active sync add and remove programs it let me click on remove but didnt remove it, just hung
This soft does actually suck. Anthasoft.com's web site needs some TLC but their support got straight onto my issue.
Shame I couldnt wait and reset really.
But SD card intact
Microdrive intact.
Copied program files and my docs out onto PC before Hard reset.
all ok really....jsut missions getting it back together.
yarod_g14 said:
Well, the app locks the device on startup. ASks for password (in box under says password : demo - this didnt work with soft keyboard hard keyboard upper and lower case etc...)
So Couldnt actually get to home page...
When I selected the item through active sync add and remove programs it let me click on remove but didnt remove it, just hung
This soft does actually suck. Anthasoft.com's web site needs some TLC but their support got straight onto my issue.
Shame I couldnt wait and reset really.
But SD card intact
Microdrive intact.
Copied program files and my docs out onto PC before Hard reset.
all ok really....jsut missions getting it back together.
Click to expand...
Click to collapse
Might want to have Safe Mode installed in case this happens to you again with other software. It's saved my butt several times already.
Safe Mode and WM6
Hi,
will Safe Mode 2.x work with WM6?
One the Monocube website they are only talking about WM5 ...
http://www.monocube.com/content/view/5/37/
Did anyone checked this out already?
___
Seq
Sequenzial said:
Hi,
will Safe Mode 2.x work with WM6?
One the Monocube website they are only talking about WM5 ...
http://www.monocube.com/content/view/5/37/
Did anyone checked this out already?
___
Seq
Click to expand...
Click to collapse
I have used it with WM6. Haven't had any problems yet.
Sequenzial said:
Hi,
will Safe Mode 2.x work with WM6?
One the Monocube website they are only talking about WM5 ...
http://www.monocube.com/content/view/5/37/
Did anyone checked this out already?
___
Seq
Click to expand...
Click to collapse
Yes, it works great on WM6. I've had no problems with it and it's even saved my butt once under WM6 already.
I need some assistance in UNlocking my 8125. I sent my phone into at&t for repairs, they sent the phone back locked. I am an old ATTWS customer, I have been waiting for one week for my unlock code. I recently purchased an 8525 and SIM/CID Unlocked that phone, but I need assistance with this phone. I have run the lokiwiz03a several times, but it keeps giving me "The system cannot find the path specified" on all the lines of the program. Of course at the end it does not provide an unlock code, It repeats the message.
I think you are not doing it proper,I may be wrong,but most probably you have to copy and paste two cab files 'Cert_SPCS' and 'EnableRapi' in the phone somewhere and execute them in the phone,then after that run 'lokiwizMSL' on your pc.
Cheers!
I loaded both .cab files on the 8125, they both ran succesfully. I have the phone connected to active sync. I am at a loss on this. I have no clue why this is not working. I have flashed numerous ROM's on phones, this one seems to be a pain the in the behind. At&t just returned the phone from repairs, could they have installed something to block this?
hmmm,
really strange though,may be they have put some kinda special code on it.what repairs were carried on it ?
btw,have you tried to sim unlock with WST 4.2 tool,ask mestrini,if it might do the trick.
Cheers!
I ran the WST as you requested. It is telling me that the DOC chip is write protected. When I run the CID Action and Run Super CID it returns that message. When I run SIM unlock it generates all the data from the phone and produces LOCKED in the status. At the bottom of all the data it returns DOC chip is write protected. I may be running this tool wrong, your info is appreciated.
WST simlock tool doesn't work on G4.
Easiest way:
1. Run flight mode.
2. Turn off your Wizard and insert "bad" simcard.
3. Turn on your Wizzard copy Two cabs Cert_SPCS' and 'EnableRapi'
4. Install it on device memory.
5. Turn on phone (in commanager)
6. Run lokiwiz, it should work!
How do I turn on the phone with the wrong SIm in the phone, it keeps going back to the SIM lock page. I am able to turn on the flight mode, but I can not do anything else, it keep srefering back to the SIMlock page.
simlock screen = run lokiwiz and enter generated code. It must work
Everyline on the screen reports "The system cannot find the path specified" I think at&t has protected this from unlocking?
same happens to me
try running lokiwiz from c:\
make sure that two cabs are installed
wizard is an old model I think at&t is taking care over iphone now ;p
Hello:
I can't unlock my M600 because when I put the unlock code, the screen changes to "Input SIM PIN", but when I put the SIM PIN, the screen go again to input unlock code (is a loop).
This is all steps that I have made:
1) M600 without SIM card inside, connected to ActiveSync. I execute Lokiwiz03a without problems, all ok, and I get my 8 digits unlock code.
2) Power off M600 and I put a SIM card of other company.
3) Power on M600 and I get: "Input your PIN code..."
4) I put the SIM code and after 4 seconds the screen changes to "Network Locked. Please input the unlock code".
5) I put the 8 digits unlock code and after 2 seconds the screen changes to Step 3 ("Input your PIN code..."), and when I put the PIN code, the screen changes to "Network Locked. Please input the unlock code"..., IS A LOOP!!.
I'm desperate, I don't know that I can do. I have make soft and hard reset but I have the same issue.
Please, I need help..., what can happen?, exists any alternative method for unlock my M600?.
Thanks for all!!
Fossy_01 said:
Hello:
I can't unlock my M600 because when I put the unlock code, the screen changes to "Input SIM PIN", but when I put the SIM PIN, the screen go again to input unlock code (is a loop).
This is all steps that I have made:
1) M600 without SIM card inside, connected to ActiveSync. I execute Lokiwiz03a without problems, all ok, and I get my 8 digits unlock code.
2) Power off M600 and I put a SIM card of other company.
3) Power on M600 and I get: "Input your PIN code..."
4) I put the SIM code and after 4 seconds the screen changes to "Network Locked. Please input the unlock code".
5) I put the 8 digits unlock code and after 2 seconds the screen changes to Step 3 ("Input your PIN code..."), and when I put the PIN code, the screen changes to "Network Locked. Please input the unlock code"..., IS A LOOP!!.
I'm desperate, I don't know that I can do. I have make soft and hard reset but I have the same issue.
Please, I need help..., what can happen?, exists any alternative method for unlock my M600?.
Thanks for all!!
Click to expand...
Click to collapse
If you have another SIM card try that. Also, try removing the SIM PIN on the current SIM card. (you'll need another phone/device)
Solved!.
I have restore the full original Orange Rom and unlock code was work!!.
If anyone have this problem, I reccommended install the original rom and try again.
Thanks!!
Fossy_01 said:
Solved!.
I have restore the full original Orange Rom and unlock code was work!!.
If anyone have this problem, I reccommended install the original rom and try again.
Thanks!!
Click to expand...
Click to collapse
I think it might be worthwhile putting that in the lokiwiz thread/wiki entry.
Sorry 3v5y, I'm searching the Lokiwiz forum but I can't find...
Please, tell me the direct link and I will put the issue with solution.
Thanks
Here's one link: http://wiki.xda-developers.com/index.php?pagename=Prophet_Unlock_Sim
Thanks I3v5y.
I have modified the wiki.
Please see the result (the lines in red color is the lines that I have added) and if you believe it is necessary, rewrite my text because I think that my english is not good...
Instructions for SIM Unlocking your Prophet :
1. Download ftp://xda:[email protected]-developers.com/Uploads/Prophet/Prophet-tools/Lokiwiz03a.zip
2. Unzip Lokiwiz03a.zip somewhere on your computer
3. Make sure that your phone is connected via ActiveSync with the computer
4. Execute lokiwizMSL.bat on your computer
If it states: "Could not update itsutils.dll to the current version, maybe it is in use?"
Do the following :
*Copy the cab's from the Utils folder in the Lokiwiz03a.zip file to your Prophet and execute them.
(There are two files : "Cert_SPCS.cab" and "EnableRapi.cab")
*Execute lokiwizMSL.bat on your computer
5. It will give you the SIM unlock code after it runs, write it down somewhere.
* In some cases, if you get characters (or characters and numbers), indicates that your phone-pda was ulocked.
6. Just get a different SIM from the one your phone is locked to, and install it in the phone (you have to turn off your phone)
7. Turn on your phone
8. When it asks your pin code enter your normal pin.
9. It then asks you for the Service Provider Unlock Code: Here you insert the SIM unlock code you wrote down in step 5.
* NOTE: If you have a non original ROM, you can have a problem with unlock code, because when you put it, the screen
returns to SIM PIN code, and when you put the pin code, the screen changes again asking for unlock code...,
if this is your case YOU MUST CHARGE THE ORIGINAL ROM IN YOUR PDA, in this case only with your original rom you can
unlock the pda-phone.
10. That's it, enjoy your unlocked Prophet !
hello everybody
Yesterday my phone asked me to update and i accepted it unfortunately.
I live in France, phone is bought here blocked by SFR operator.
One year ago i got the code to unblock from SFR and I unblocked it and since then i have used FREE, COSMOTE(Greece) and lately i m using BOUYGUES operator.
Problem:
After the update, phone got simlocked again and with my BOUYGUES sim it asks me for a "sim network unlock pin". I insert the code i had but it doesn't unlock it.
I called SFR and fun fact is that they claim that the unlock is permanant (they are not aware of this new issue) and the unlock code unique. I asked them the code to ensure what i had is correct and they confirmed... So code is 100% correct...
Since it was not working they told me to remove any sim card from the phone and do the following steps...
1 click on TELEPHONE icon
2 enter *#46744674 and press #
3 the code should disappear
4 then enter #7465625*638* and press #
5 you will now be prompted to enter the unlock code
6 enter the code NCK and press ok OK.
if code is good, phone gets unlocked
So while step 2-3-4 work fine, the #7465625*638*# disappears but step 5 never happens... There is not screen prompting me to insert the code....
I called Samsung after this and I told them everything i ve tried...
they proposed me to do this --> *#0111*CODE# and it will get unlocked... (super unfriendly french customer service hanged up on me)
I did it but nothing happen.. not even the *#0111*CODE# got disappeared like it happened with steps 2-4 above....
To me it looks like the new android 4.1.2 messed up everything....
Problem seems new... i found two posts in french describing the same problem with no solution but i cant post the links here.
Any ideas how to fix this?
Thanks for reading this
Yeah, root it & unlock it.
Sent from the little guy
Root the phone and then use galaxsim_unlock app from " http://forum.xda-developers.com/showthread.php?t=1846451 " or u can download the app from play store!
Issue in process of rooting the phone - to unlock the phone
Hi,
I have similar problem with my Samsung Galaxy S II SGS2 GT-i9100.
My phone is UNROOTED.
After it was updated from ICS to Jellybean (upgrade via the air, not using Kies and not using Odin), I am also asked for SIM UNLOCK PIN.
The phone was originally bought locked to O2 UK network, then unlocked, but the unlock code used in past does not work now.
The problem is that in all places it says to root the device, and in order to root it, I am advised to create a backup copy of efs folder, and in order to backup the efs folder I need to have root permissions... - deadlock !
In additions, many guides says that in order to root the phone, I need to have only for phones that are SIM FREE, which brings me back to start - I will not be able to flush ROM/Kernel to root it as my phone is SIM locked...
Any suggestions that will help me unlock the phone?
Thanks!
dudders007 said:
Root the phone and then use galaxsim_unlock app from " http://forum.xda-developers.com/showthread.php?t=1846451 " or u can download the app from play store!
Click to expand...
Click to collapse
You're very confused.
1) Root your phone. There are multiple methods. Search/read/learn & choose whichever one you think is best for you. The phone does not have to be 'sim-free' or unlocked or anything else in order to root it. As I said, you are clearly confused. You need to search/read/learn & not do anything to your phone until you're no longer confused, or you'll 'break' it.
2) Create an EFS backup using kTool from Google Play. Keep one copy of this backup on your PC, and another copy on the external SD card in your phone if you have one.
3) Unlock the phone with whichever app you want to use to unlock it.
Hello
I found an easy way to root it but i cant post a link... so google "[RESOLU] code deverouillage reseau" and you ll see the thread... (it is in french)
As user "gab34" says, i downloaded the proper zip file (in my case was XWLSD_root.zip) and put it in the sd card as it is (as a zip). (you have to subscribe to let you download the file :/)
Then i pressed up-power-home buttons until it turns off and on again.
Then i was in the recovery meny , and with the volume button i went down to "apply update from external storage" i pressed the power button to enter, chose the file XWLSD_root.zip, press again power button, installation will take place in ../ , press power button, the reboot now and power button.
The phone restarts as rooted and then you can use GALAXSIM to unlock it..
You download Galaxsim unlock for free, then it tells you if it can unlock and if so you pay 3 euros for full version and unlock it....
Try google translator and a french speaker if you need help with the site... It took me 10 minutes to do it...
If not, try to google how to root easily like i did with just a zip file in the sd card...
Hope it helps
Thanks but we kinda know how to do that.
Please don't (try to) post a link from another site, those sites get the info from xda anyway.
Sent from the little guy
Hi at all!
After yesterdays update over WiFi (don't know which exactly, but I think it's MiUI8 6.9.8) my Redmi Note 3 (Qualcomm, 32GB) wouldn't let me unlock the device neither with fingerprint nor pattern. Before I updated it was normally unlocking. Normally I use fingerprint, so at first I thought i forgot the pattern, but after several attempts the phone went into lock mode. I am 99% sure I know the right pattern, but it won't unlock.
I already read this guide: http://en.miui.com/thread-5684-1-1.html and tried this https://www.youtube.com/watch?v=NMAPEhH5z-8
But I have still several problems:
- USB debugging not enabled
- no recovery installed
- no root or open bootloader or anything like that
- no backup of all photos, which are on the phone itself and not on the SD card (I just came back from holidays)
- no cloud or similar backup
- Mi Pc Suite does not detect phone
- Google Device Manager states "Since Google has verified that a screen lock is already set, the password that you entered won't be needed." if I try the send a new lockscreen.
This method (with flash afterwards) could help me, I guess, but I still would loose everything: http://forum.xda-developers.com/redmi-note-3/how-to/guide-reboot-to-edl-mode-fastboot-test-t3398718
I have absolutely no idea how i can unlock my phone without loosing any data (especially the photos).
Please if anyone has an Idea, help me!
Same happened to me so I restored my backup, once the restore had finished I removed the finger print and pin number (I had read about this on the xiaomi Forum). Then did the update again and this time it was OK
sounds easy, how did you restore the backup?
Before restoring any backup, I suggest you hard restart your phone. long press the power button.
but if I make a Hard Reset I will loss everything on the phone.
Is there maybe a possibility to insert some sort of file or command via EDL mode, that USB debbuging will be enabled? http://forum.xda-developers.com/redmi-note-3/how-to/guide-reboot-to-edl-mode-fastboot-test-t3398718
No not the hard reset. I was talking about hard restart. The phone will just restart.
ahh I see, sorry my fault.
But nonetheless I din't made any backup ever with this phone.
same problem here
my phone redmi note 3(qualcomm 32gb) is also locked just yesterday ! it shows try again after 120 minutes and after the time completed it shows pattern and it will be locked again and shows the same dialouge after trying my correct password ! actually we shoud get forgot password option behind the emergency option ! please do give a reply to me if you find any solution it means a lot to me !
Well I am afraid I can't help you either... after searching for 2 days I found no solution and flashed my phone. so all data was lost...