Know of anywhere to get JUST the screws, I've recently changed my case... well parts and wasn't as careful as I should've been and I am missing a few screws
avatar_43 said:
Know of anywhere to get JUST the screws, I've recently changed my case... well parts and wasn't as careful as I should've been and I am missing a few screws
Click to expand...
Click to collapse
maybe ebay?
Related
i lost all screws from my touch hd. any idea where i can get new ones?
refresh my question.
same question.. i need some screws to
+1 here, only because when I disassembled mine I '*****ed' one of the PCB phillips screws
Hello, my phone fell down an the bottom aluminium plate is heavily scratched. My question is that its possible to replace it without opening the phone. Thx and sorry for my bad english.
xzultra said:
Hello, my phone fell down an the bottom aluminium plate is heavily scratched. My question is that its possible to replace it without opening the phone. Thx and sorry for my bad english.
Click to expand...
Click to collapse
If I'm not wrong the bottom is plastic instead of aluminium,while the side is aluminium.
If you change it you will lost waterproof.
There is only adhesive tape to hold the bottom bezel, no screws. So i thought to heat the adhesive a litle bit and replace it but im not sure if its even possible.
xzultra said:
There is only adhesive tape to hold the bottom bezel, no screws. So i thought to heat the adhesive a litle bit and replace it but im not sure if its even possible.
Click to expand...
Click to collapse
Ive found something
At the top there's the mic and bottom there's speaker,you gonna becareful!
atrix2 said:
At the top there's the mic and bottom there's speaker,you gonna becareful!
Click to expand...
Click to collapse
Will they repair it in official sony service?
xzultra said:
Will they repair it in official sony service?
Click to expand...
Click to collapse
Not so sure,if the factory screen protector is scratched,they will replace,but not sure about the bottom plastic plate.
It is fine if it does not effect the phone and waterproof,mine also got scratch at top but I just leave it there,maybe you can use a case.
They do not replace parts if there is only cosmetic damage. But you can always try to open a ticket and send your device off to repair ..you might be lucky
SÜPERUSER said:
They do not replace parts if there is only cosmetic damage. But you can always try to open a ticket and send your device off to repair ..you might be lucky
Click to expand...
Click to collapse
Do you think its possible to replace only the bottom bezel or its connected with side bezels?
there were service manuals posted here, I think I saved them to mega...
https://mega.co.nz/#!Mk9zFQDC!FU8EMRrrGvLPOHc0BlK5ubp1L0e6voYt5tH1Y1ZQu5A
atrix2 said:
Not so sure,if the factory screen protector is scratched,they will replace,but not sure about the bottom plastic plate.
It is fine if it does not effect the phone and waterproof,mine also got scratch at top but I just leave it there,maybe you can use a case.
Click to expand...
Click to collapse
successfully replaced! :laugh:
xzultra said:
successfully replaced! :laugh:
Click to expand...
Click to collapse
Waterproof still works?
atrix2 said:
Waterproof still works?
Click to expand...
Click to collapse
Still waterproof, this small piece of plastics doesnt affect it.
Never seen or heard of this before, but this happened to me. See attached image. What is this thing? It doesn't move when I tap the phone against something. Pictures are obviously crap. Is my next move removing the back cover to get rid of this thing?
Phone is less than 1 year old, but I don't think I can get warranty service as I bought it in the US as the international "no warranty" version from Amazon.
Info
camaro322hp said:
Never seen or heard of this before, but this happened to me. See attached image. What is this thing? It doesn't move when I tap the phone against something. Pictures are obviously crap. Is my next move removing the back cover to get rid of this thing?
Phone is less than 1 year old, but I don't think I can get warranty service as I bought it in the US as the international "no warranty" version from Amazon.
Click to expand...
Click to collapse
it is faulty hardware send it for replacement
Good Luck
:good:
I got a hair dryer and guitar pick and pulled the back cover off just enough to get the debris out. It appears to be a stray bit of adhesive or sealing tape around the camera lens. All good now, except my phone is probably no longer waterproof.
camaro322hp said:
I got a hair dryer and guitar pick and pulled the back cover off just enough to get the debris out. It appears to be a stray bit of adhesive or sealing tape around the camera lens. All good now, except my phone is probably no longer waterproof.
Click to expand...
Click to collapse
Did you re use the stock adhesive?
civicsr2cool said:
Did you re use the stock adhesive?
Click to expand...
Click to collapse
Yes. I didn't pull off the entire back cover, only pulled up the corner where the camera is. I suppose I could buy a new back with fresh adhesive to try and make it waterproof again, but I'm not sure how successful that would be.
camaro322hp said:
Yes. I didn't pull off the entire back cover, only pulled up the corner where the camera is. I suppose I could buy a new back with fresh adhesive to try and make it waterproof again, but I'm not sure how successful that would be.
Click to expand...
Click to collapse
Gotcha. I'm just curious because I'd like to sand down and buff out a clear back for mine. I think it'd be pretty neat.
civicsr2cool said:
Gotcha. I'm just curious because I'd like to sand down and buff out a clear back for mine. I think it'd be pretty neat.
Click to expand...
Click to collapse
That does sound cool. Show us some pics if you manage to do it.
Hello, I've got a question. Does anybody have got (or know where to find it) a template of the back panel of the phone? I've got a sheet of 3M foil and I'd like to cut out a protective sticker from it, but I need a template in 1:1 scale. Maybe someone have got something like this?
You may try searching on korean google.co.kr or ask from this YouTube channel JerryRigEverything
Not sure but I hope you will find that.
Sent from my SM-G930F using Tapatalk
tharindunw said:
You may try searching on korean google.co.kr or ask from this YouTube channel JerryRigEverything
Not sure but I hope you will find that.
Sent from my SM-G930F using Tapatalk
Click to expand...
Click to collapse
Thanks for your help, I've found some templates, I'll have to print them on paper and fit on the back, maybe I'll find the good one
debowiakr said:
Hello, I've got a question. Does anybody have got (or know where to find it) a template of the back panel of the phone? I've got a sheet of 3M foil and I'd like to cut out a protective sticker from it, but I need a template in 1:1 scale. Maybe someone have got something like this?
Click to expand...
Click to collapse
And this is why you never throw away them plastic screen protectors that where on the phone when you bought it I always stick mine to the box.
RiTCHiE007 said:
And this is why you never throw away them plastic screen protectors that where on the phone when you bought it I always stick mine to the box.
Click to expand...
Click to collapse
I don't have mine yet
Maybe next week but I like to be prepared. That's why I've bought an UAG case and screen protector
debowiakr said:
I don't have mine yet
Maybe next week but I like to be prepared. That's why I've bought an UAG case and screen protector
Click to expand...
Click to collapse
Ah well then you are lucky and the phone will come with a ready to use template on the back side and front
Any chance you could share those templates?
I've got something like this
I'm planning to transfer the gasket from the original cover to the replacement back cover that I bought. For some reason, the replacement doesn't come with it.
YamiYukiSenpai said:
I'm planning to transfer the gasket from the original cover to the replacement back cover that I bought. For some reason, the replacement doesn't come with it.
Click to expand...
Click to collapse
just pull the lens carefully, it comes glued
jorgescus said:
just pull the lens carefully, it comes glued
Click to expand...
Click to collapse
Do I need to heat it up?
Also, do I pry it out with a spudger or something?