I need help, i have broken the plastic that holds the screen cable connected with the flex cable...Has anyone have any idea what to do?
mali_loodak said:
I need help, i have broken the plastic that holds the screen cable connected with the flex cable...Has anyone have any idea what to do?
Click to expand...
Click to collapse
upload some pics,so we can see the problem..
Related
I've made sure I purchased the correct replacement for my screen. Followed a guide and got it all hooked up. The phone powers on but I get a white screen.
Anyone have any guesses as to what could be causing this?
Your help would be much appreciated as I would hate buying another phone.
Incorrect ribbon cable seat.
Take it apart and make sure that both the ribbon cable on the side, and the bottom with the tiny black screws are properly seated.
Yea i have tried all of that....but I just tried tinkering with it again and i was able to get a partial picture by changing the back pressure of where the LCD ribbon plugs into the other ribbon assembly the buttons are connected to.
So I am guessing there needs to be a super secure conenction at this point. Problem is...the black latch that holds the cable from the LCD to the other ribbon is broke so i cant make it pinch the cable.
Anyone know where I can find a replacement for this other than buying a broken hemes for parts?
You need the flex cable connection, and there is a site in canada that has them.
www.cnn.cn
Yea I checked that out....I don't see it, do you?
teknics said:
You need the flex cable connection, and there is a site in canada that has them.
www.cnn.cn
Click to expand...
Click to collapse
.cn is china not canada.
Good point - ca = canada
hi
i have a htc touch plus or as they call it htc touch dual.digitizer issue it stoped responding so i bought new one fitted in and still the same problem .i think is a software problem i guess driver software for touch screen .if any one can help please
thanks
Touch Dual digitizer
Hi Saliml2
Not convinced it is a software issue. My digitizer on T-Mobile Touch Plus did the same thing. It stated behaving erratically and then stopped responding altogether. I replaced the digitizer (via eBay) and it work for a few days and then stopped again.
I have read around the internet and have tried several ROM updates etc (currently running a WM 6.5.5 found in other area of this forum) but this has not solved the problem.
It seem to be an alignment issue - i.e. screen alignment is outside the screen area, but there seems to be no way of getting it back. Could be a fault on the phone mainboard (?) but there doesn't seem to be any info around apart from sending it to HTC for repair (not viable as the phone value negates this)
My phone is still not working, I might try opening it up again and reseating the digitizer cable but have done this twice already.
Have you try change the flex cable?
I had one to, with the same problem, and after changing the flex everything was ok...
Good luck!
Hi Amokh Just to clarify, what is the flex cable? The digitizer has a cable already attached to it that plugs in to a zif connector on the mainboard - I assume that this controls the data flow for the digitizer.
Any help would be appreciated.
deepthought2471 said:
Hi Amokh Just to clarify, what is the flex cable? The digitizer has a cable already attached to it that plugs in to a zif connector on the mainboard - I assume that this controls the data flow for the digitizer.
Any help would be appreciated.
Click to expand...
Click to collapse
Maybe this is helpfull http://www.pdacenter.ru/razborka/razbor_htc_touch_dual/
Goodluck
Flex cable, i was mean the cable between the mainboard and the lcd block, you can see it in the previous link, picture 20. Have you try it to change?
hello guys how did you manage to put the digitizer cable in place mine doesn t seem to get in place do i need something to hold the connector in place???
Hello all.
While I was taking my HD2 apart to replace a cracked screen (glass digitizer) I accidentally broke the connector off one of the wires. The wire is black and a few inches long with a silver and round press on connector on each end. It attaches to the board that houses the vibrator motor and runs down the right side of the phone (if you were looking at it face down and partially disassembled).
Unfortunately, I lost the metal piece that broke off the wire (the thing is tiny!), so I can't just solder it back on. Any idea on where I can buy a replacement? I've spent about 6 hours today on ebay and google to no avail. Searching for "HD2 black wire" and anything similar is hardly efficient, but that's all I know about it.
Any help appreciated.
Thanks,
Chris
Good question, I think I damaged the cable to the volume buttons so it would be cool if someone has an adress where we can get spare parts except LCD and Digitizer..
this guy on ebay seems to be selling an HD2 in parts. you might find what you need here:
http://stores.ebay.co.uk/Right-Click-Enterprises/_i.html?_nkw=hd2&submit=Search&_sid=131407386
Thanks, I sent that guy a message and hopefully it'll work out.
Anyone else have a source?
connector of my hd2 is also broken HTC says that the mainboard must be change and I have to pay € 230 because that is my responsibility
I think you have damaged your coaxial cable connector for wifi and bluetooth. Google will help you perhaps.
I believe that my wifi/bluetooth cable is broken, as I have no wifi or bluetooth signal since dropping my phone as reported in a previous post of mine. Can anybody advise me on the difficulty of undertaking this repair myself, does it involve complete disassembly of phone, any soldering etc. If this is the case I don't feel confident enough to do this so does anybody know of someone who does this sort of repair, I have found the cable on e bay for £7 and it looks like it has push on connectors ?
if the connectors on the boards are not broken then all you need is the coaxial cable with connectors on the two end. you need not disassemble the whole set, just open the back cover, connect one end of the cable to mother board and other end to the rigid flex board and that's it.
WiFi and Bluetooth not working
raincybercafe said:
if the connectors on the boards are not broken then all you need is the coaxial cable with connectors on the two end. you need not disassemble the whole set, just open the back cover, connect one end of the cable to mother board and other end to the rigid flex board and that's it.
Click to expand...
Click to collapse
Do you think that this is my problem as since I dropped my HD2 I have no wifi (unless sat ontop of router) or bluetooth or fm radio, is it easy to get to the coax cable by removing back cover, whereabouts is it ?
raincybercafe said:
if the connectors on the boards are not broken then all you need is the coaxial cable with connectors on the two end. you need not disassemble the whole set, just open the back cover, connect one end of the cable to mother board and other end to the rigid flex board and that's it.[/QUOTE
Fixed it, opened up phone and spotted that at one end of the black wire the connector was not pushed onto the motherboard securely, I pushed it home and hey presto, wifi and Bluetooth now working, phew, Thanks for your help !
Click to expand...
Click to collapse
i have a galaxy tab 10.1 that was having screen problems i found out that it was the lcd flex cable if i wiggle it the screen comes on. So its defiantly that cable and not the hardware my problem is i cant find a replacement anywhere just everything else beside the lcd cable i need!
any help will be greatly appreciated.
there's 3 cables i see on the galaxy tab 10.1 the charging port the digitizer and the lcd
lost896 said:
i have a galaxy tab 10.1 that was having screen problems i found out that it was the lcd flex cable if i wiggle it the screen comes on. So its defiantly that cable and not the hardware my problem is i cant find a replacement anywhere just everything else beside the lcd cable i need!
any help will be greatly appreciated.
there's 3 cables i see on the galaxy tab 10.1 the charging port the digitizer and the lcd
Click to expand...
Click to collapse
Same situation here.
Any luck?
It seems like we found a defect right? three people with the same issue between ten days or so ...
two month ago i have replaced the charging port flex, really annoying....
martocapo said:
Same situation here.
Any luck?
It seems like we found a defect right? three people with the same issue between ten days or so ...
Click to expand...
Click to collapse
Could be a defect.
The cable it self instead on being straight is bent 90 degrees to go up and im assuming the crease finally snapped in the cable
Guys,
Check the follwing thread Link .
I am following up the same issue there.
Regards
martocapo said:
Guys,
Check the follwing thread Link .
I am following up the same issue there.
Regards
Click to expand...
Click to collapse
i have the same problem what should i do? replace the lcd flex cable? also mine is overheating too? does that has to be with the flex to ?
Hello
I have a big problem with my Razr, my usb connector of my razr is broken.
I can not charge it anymore, it is not caused by usb cable because I tried with differents.
Someone know if we can buy new usb connector and replace it ?
Thanks you.
nespresso33 said:
Hello
I have a big problem with my Razr, my usb connector of my razr is broken.
I can not charge it anymore, it is not caused by usb cable because I tried with differents.
Someone know if we can buy new usb connector and replace it ?
Thanks you.
Click to expand...
Click to collapse
Is the connector on the phone "physically" broken, or does it just not charge?
It just doesn't charge.
But the connector is damaged for sure.
Just as a temp solution you Cern use battery charges (connecting their probes directly to the bat. + -)
Sent from my SAMSUNG-SGH-I847 using xda app-developers app
I tried to do that yesterday but it didnt work.
I cut an usb cable and I put the red and black wires only on screw (
I did not have a screwdriver )
This method : http://www.youtube.com/watch?v=qs2t-7ALT7U
I have bought a HTC ONE S, if someone want to buy my razr in low price...