Related
hello friend, Raj here.
I have been using the X10i since past 6 months. I bought the phone my UAE & i am presently using it in India.
1) Is there any firmware upgrade available for my phone?
My phone info says-
Model - X10i
Firmware - 1.6
Baseband version - 1.0.14
Build number - R1FA014
2) My phone does not have the Android market application inbuilt in it! how & from where do i download that app?
3) How do i install applications downloaded to my computer from Android market, to my phone?
4) I am not able to access Calender since it requires me to log in to my Gmail account. everytime i try to do that, it says "error, try next time"! is there any way i can start the calender without registering?
Thanks.
raj_5004 said:
1) Is there any firmware upgrade available for my phone?
Click to expand...
Click to collapse
Hi.
Yes there is, considering a lot of us are running R2BA026, that should give you an idea of how far behind you are.
raj_5004 said:
2) My phone does not have the Android market application inbuilt in it! how & from where do i download that app?
Click to expand...
Click to collapse
Personally, I would debrand and update your handset with UK generic FW, which will give you the Market app, which will answer question 3, and as you need to register for the Market to use it, that also answers your 4th question.
1) Install SEUS (Sony Ericsson Update Service).
You can get it from here: http://www.sonyericsson.com/cws/download/1/110/61/1275980198/Update_Service_Setup-2.10.6.21.exe
2) Run SEUS, follow the prompts. You don't need to update the phone through it, but get the phone ready for updating. This process should install the drivers necessary for the rooting process.
Note: I suggest you keep your USB cable attached to that USB port. Remember which USB port of your computer it's attached to, as changing USB ports can lead to a bit of confusion for the next 2 steps!
3) To check if #2 was successful, click on Start, click Run, and type: regedit
In the Registry Editor that pops up, click on Computer, press CTRL+F, and search for this: USB\Vid_0fce&Pid_adde\
After it's finished finding, on the right side you'll see DeviceInstance, then it says REG_SZ, then it says something like USB\Vid_0fce&Pid_adde\5&270d2a78&0&3
You'll need that last bit (in this example: 5&270d2a78&0&3 Yours would probably be different). This is your DeviceID (you'll need it soon!)
Note: You may have multiple of these if you plugged the USB cord into many USB ports on your computer. Each USB port will give a different DeviceID, so if you have more than one DeviceID, you'll have to choose one, and if it doesn't work (you'll find out when you reach #5!) you will have to choose another one.
Alternatively, download the file in the next step and extract it, go to the folder called 1st, and run the DeviceID.jar file. It should give your DeviceID
4) Download this:
http://filevo.com/1nlq8wryo11u.html
or from here: http://rapidshare.com/files/404363083/i_R1FA16_ft.rar.html
Extract it.
In the step1 folder, you'll see a file called DeviceID.txt
Open it up, delete whatever's there, and put YOUR DeviceID (that you found from the previous step).
Save the file and close notepad.
Note: Make sure there are no extra spaces or lines after/before the DeviceID. The ONLY thing that should be in the file is your DeviceID, NO SPACES/LINES (for example, only this: 5&270d2a78&0&3 [yours will probably be different])
5) Take out the USB cable from your phone (leave it plugged into your computer)
Turn your phone OFF
Open up step1.cmd (it's not inside the step1 folder, but outside it), but DON'T PRESS ANYTHING
Now we have to put the phone into flash mode. This is how you do it:
Hold the Back button on your phone, and while holding the back button, insert the USB cable into the phone.
A green light should come on the phone (like when it's charging or a missed call)
Quickly "Press any key to continue..." in the open step1.cmd window.
Let it finish what it's doing. It will say "Press any key to continue..." after it's finished. Until then, DON'T touch anything!
If you get problems in this step, refer to this post:
http://forum.xda-developers.com/showpost.php?p=6970868&postcount=3
Here's a helpful video for common java issue: http://forum.xda-developers.com/showthread.php?t=713457
After completion, this will give you a Generic X10i R1FA016 firmware (check it by pressing the left button, go to settings>about phone and at the very bottom under build number)
Click to expand...
Click to collapse
- Newbies Guide to Rooting X10 and giving you the newest firmware!
Follow those steps and when you've completed them run SEUS which should update you to R2BA026, and give you the Market app. If you run in to any issues read the links provided as the chances are it will be user error if you do.
Thanks a lot buddy.
Will de-branding my phone affect future upgrades to Android 2.1 in any way?
Also, why is de-branding necessary to access calender???
raj_5004 said:
Will de-branding my phone affect future upgrades to Android 2.1 in any way?
Click to expand...
Click to collapse
Nope, apart from you'll be the first in line to get it.
raj_5004 said:
Also, why is de-branding necessary to access calender???
Click to expand...
Click to collapse
It isn't, but if want to use the Market you are going to need a gmail account.
I tried using SEUS but failed at step 2 itself!
It says press back button while inserting USB cable in phone & keep pressing back button. i did the same & waited & waited for 5 minutes, but no response!
then my finger started hurting & i had to abort the process! does it take so long?
raj_5004 said:
I tried using SEUS but failed at step 2 itself!
Click to expand...
Click to collapse
You're not doing it right, should take about 5 seconds for seus to recognise the phone. Try again.
Sorry for the back-to-back posts, but can i update my phone country to India instead of UK? i think Indian X10s do get Android Market. Since i am using the phone here in India & in future would like to get this serviced in india itself, i would prefer my phone to show India in country!
It honestly doesn't matter. I'm in Canada but I'm using a Latin American firmware. But yes, to get it serviced I guess you need it. How about asking someone with the Indian firmware to dump it for you?
That is precisely the reason i am looking for the indian version instead of UK.
None of my friends have a X10 & strangely, even google dint yield any satisfactory results.
I will opt for the UK update only if Indian update is not available.
Also, i am still not able to open the calender using my gmail account. evertime it says "error! try again later" !!!
raj_5004 said:
That is precisely the reason i am looking for the indian version instead of UK.
None of my friends have a X10 & strangely, even google dint yield any satisfactory results.
I will opt for the UK update only if Indian update is not available.
Also, i am still not able to open the calender using my gmail account. evertime it says "error! try again later" !!!
Click to expand...
Click to collapse
so did you manage to update to a newer firmware yet? you said a while back that "holding the back button" did not work. You need to have the phone off before you do this step.
1. turn phone off
2. connect usb cable to phone, but not to pc.
3. open SEUS and get to the stage that it says waiting for phone connect.
4. press and hold the back button (which will power your phone on in flash mode) and connect the USB cable to pc.
SEUS should now say "stop pressing back button" or something to that effect.
mrtim123 said:
so did you manage to update to a newer firmware yet? you said a while back that "holding the back button" did not work. You need to have the phone off before you do this step.
Click to expand...
Click to collapse
No, it still dint work. i tried it thrice & following all instructions carefully. i had the phone switched off.
1. turn phone off
2. connect usb cable to phone, but not to pc.
Click to expand...
Click to collapse
in SEUS, it says first connect USB cable to PC, then to phone.
3. open SEUS and get to the stage that it says waiting for phone connect.
4. press and hold the back button (which will power your phone on in flash mode) and connect the USB cable to pc.
SEUS should now say "stop pressing back button" or something to that effect.
Click to expand...
Click to collapse
Nothing like this happens in my case. Dont know whats wrong!
Guys, i managed to install Astro File Manager over the air! i did install a few apps to my comp & then to my phone using AFM but not all apps are available to install on the comp! thats the reason i needed Android Market on my phone.
Also, i dont understand why i cant register to google through my phone as i have to use the phone calender.
Guys, it re-installed SEUS & it detected my phone but i again failed! i am dumb!!!
1) Install SEUS (Sony Ericsson Update Service).
You can get it from here: http://www.sonyericsson.com/cws/down...-2.10.6.21.exe
2) Run SEUS, follow the prompts. You don't need to update the phone through it, but get the phone ready for updating. This process should install the drivers necessary for the rooting process.
Note: I suggest you keep your USB cable attached to that USB port. Remember which USB port of your computer it's attached to, as changing USB ports can lead to a bit of confusion for the next 2 steps!
3) To check if #2 was successful, click on Start, click Run, and type: regedit
In the Registry Editor that pops up, click on Computer, press CTRL+F, and search for this: USB\Vid_0fce&Pid_adde\
After it's finished finding, on the right side you'll see DeviceInstance, then it says REG_SZ, then it says something like USB\Vid_0fce&Pid_adde\5&270d2a78&0&3
You'll need that last bit (in this example: 5&270d2a78&0&3 Yours would probably be different). This is your DeviceID (you'll need it soon!)
Click to expand...
Click to collapse
I reached till here & searched for "USB\Vid_0fce&Pid_adde\" but no files were detected!
then i searched for "USB\Vid_0fce&Pid_adde" & i found a file which says-
MatchingDeviceId Reg_SZ usb\vid_0fce&Pid_adde
Thats it! no device ID in front of it!
raj_5004 said:
Guys, it re-installed SEUS & it detected my phone but i again failed! i am dumb!!!
Click to expand...
Click to collapse
Can you clarify, did you get into flash mode for it to install the drivers?
I re-installed SEUS. then I started SEUS, switched off my phone for 30 secs, connected USB cable to computer, then connected USB cable to phone while pressing the back button & kept pressing the back button until the phone got switched ON.
then SEUS asked me to open Notification bar & turn ON USB. i left the back button & did the same. then the screen showed "X10i connected" & your phone is up to date!
then i tried whatever you had mentioned but it was of no use as mentioned in my post above.
Also, SEUS detects my phone only 1 out of 5 times. the remaining times, it takes soooooo long that i have to abort the process & SEUS hangs!
Also, i have noticed that in my SEUS, in the phone models where you have to select your phone, there are two options, both which look like an X10 with names "X10" & "SO-01B". which one should i select? i tried with X10 but failed. then i tried with SO-01B & it dint detect.
You problem is that seus is not detecting your device..
Soln... User a laptop with win xp or vista or 7 32 bit...
Do a complete uninstall of seus. Clean the registry of any seus entries..
Reinstall seus..
Use a different usb port.
Now try..
The device is an x10 unless you your it from japan which if the case is then it is the so-o1.
If you want dump of indian firmware I can help you but I dont think a dump will be of much use to
You..
Chetan
raj_5004 said:
I re-installed SEUS. then I started SEUS, switched off my phone for 30 secs, connected USB cable to computer, then connected USB cable to phone while pressing the back button & kept pressing the back button until the phone got switched ON.
then SEUS asked me to open Notification bar & turn ON USB. i left the back button & did the same. then the screen showed "X10i connected" & your phone is up to date!
then i tried whatever you had mentioned but it was of no use as mentioned in my post above.
Also, SEUS detects my phone only 1 out of 5 times. the remaining times, it takes soooooo long that i have to abort the process & SEUS hangs!
Also, i have noticed that in my SEUS, in the phone models where you have to select your phone, there are two options, both which look like an X10 with names "X10" & "SO-01B". which one should i select? i tried with X10 but failed. then i tried with SO-01B & it dint detect.
Click to expand...
Click to collapse
cvchetan said:
You problem is that seus is not detecting your device..
Soln... User a laptop with win xp or vista or 7 32 bit...
Click to expand...
Click to collapse
Sadly, i dont have a laptop, i am not a laptop person!
Do a complete uninstall of seus. Clean the registry of any seus entries..
Reinstall seus..
Use a different usb port.
Click to expand...
Click to collapse
I tried all the above but in vain!
The device is an x10 unless you your it from japan which if the case is then it is the so-o1.
Click to expand...
Click to collapse
Thanks for confirming that.
If you want dump of indian firmware I can help you but I dont think a dump will be of much use to
You..
Chetan
Click to expand...
Click to collapse
yes, i would like to have the Indian firmware as that would make servicing my phones in India easier!
Can you tell me the disadvantages of having the Indian firmware when compared to the UK one?
I read that even Indian firmware has Android market & even India is getting a upgrade to Android 2.1 along with UK.
I tried using SEUS with different USB port & my phone was detected but again i found no DEVICE ID! the same thing happened which i have written in Post #14.
Is there any other method to find DEVICE ID? i even tried this-
Alternatively, download the file in the next step and extract it, go to the folder called 1st, and run the DeviceID.jar file. It should give your DeviceID
Click to expand...
Click to collapse
It shows a blank screen!!!
raj_5004 said:
then SEUS asked me to open Notification bar & turn ON USB.
Click to expand...
Click to collapse
SEUS doesn't ask you to do that, PC Companion does though. I've never known anyone have such problems getting SEUS to run.
Hi to everyone!
I bought my x10i few days ago and I wanted to install some good custom ROM, and than I tried to root it with this method:
http://forum.xda-developers.com/showthread.php?t=711907
After troubling for few hours to get to the first step because of Win 7 x64,
when I finaly manage to get run first step and finish it, phone was unable to boot!
When I press pwrbtn to turn it on, green led turns on for a second and phone vibrate for a second blank screen is all the time, after maybe 30 seconds phone just stats to vibrate endlessly!
So in attempt to recover my x10, first I was used FlashTOOL and "Generic version 2.1update1 build 2.0.2.A.0.24" firmware and after that same thing on beginning with short led light and vibrate, than a little progress screen does turn on but after while starts to changing colors and behave like strobe flashlight and that's it no further progress!
Same thing and with "Generic version 2.1update1 build 2.0.A.0.504" firmware!
I don't know what to do please help me!
Me first....
Move this to the correct forum please,
I am sure you will get more help in the q&a forum
PS, you need to run flashtool
or download SEUS or pc companion and get back to stock before trying again
bloody86 said:
Hi to everyone!
I bought my x10i few days ago and I wanted to install some good custom ROM, and than I tried to root it with this method:
http://forum.xda-developers.com/showthread.php?t=711907
After troubling for few hours to get to the first step because of Win 7 x64,
when I finaly manage to get run first step and finish it, phone was unable to boot!
When I press pwrbtn to turn it on, green led turns on for a second and phone vibrate for a second blank screen is all the time, after maybe 30 seconds phone just stats to vibrate endlessly!
So in attempt to recover my x10, first I was used FlashTOOL and "Generic version 2.1update1 build 2.0.2.A.0.24" firmware and after that same thing on beginning with short led light and vibrate, than a little progress screen does turn on but after while starts to changing colors and behave like strobe flashlight and that's it no further progress!
Same thing and with "Generic version 2.1update1 build 2.0.A.0.504" firmware!
I don't know what to do please help me!
Click to expand...
Click to collapse
gregbradley thank you for quick reply!
As maybe you can see I'm novice here, so I don't know how to move this to q&a forum!
As I already post in previous post I'w already tried to flash stock rom using FlashTool and no luck to me!
And I tried SEUS to update it and I got a message " Your phone is already up to date"
I really don't know what to do now, I'm running out of options!
me second ... ( sarcasm ) {
no f***ing clue why would you flash with oldest fw Generic version 2.1update1 build 2.0.2.A.0.24 when flashtool can root even the latest one.
did you notice that button "root" in flashtool 2.9.x.x here is tutorial in my version:
1. you enable debug mode. last time i used it it was somewhere in settings menu ...
2. see that pointer on your screen that is called mouse you move that with that small device on desk.. right on top of that button.. and you click action button if you are right handed you click right button on that small device and if you are left handed you click left button on that small device. some text will show on flashtool and after few secs it will reboot your device. no worry it is normal no need to call 911. after boot device will be rooted.
}
p.s.
flash latest fw you can find it on xda with flash tool
and do root again using method mentioned before...
http://forum.xda-developers.com/showthread.php?t=920746
Here is flashtool with different firmwares.
Read A little, you can always go back to stock.
Try and learn
I was struggling to in the beginning.
Remember to turn always enable debug mode on.
Chumby_666
thanks for so much detailed response but don't you think it's a little to much details?
Yes I know that flashtool can root the phone, but it was already to late whe I was find out, I was already brick the phone so I can't turn it on now!
davelinders
I'w already tried all those firmwares for X10i and no luck! I'm hopeless now!
When you use SEUS you should get an update button or repair button or install button anyway.
If not download the latest version of pc companion from SE and try that.
Whenever i "brick" my phone (You cant really brick an x10) I always do that and even when I have "latest" software there is an option to install anyway and that works...
Then use flashtool
1. click root
2. let it do its thing
3. click ask root permissions
4. click on xrecovery.
Then you are ready to go.
bloody86 said:
Chumby_666
thanks for so much detailed response but don't you think it's a little to much details?
Yes I know that flashtool can root the phone, but it was already to late whe I was find out, I was already brick the phone so I can't turn it on now!
davelinders
I'w already tried all those firmwares for X10i and no luck! I'm hopeless now!
Click to expand...
Click to collapse
Also post in the right thread next time
Sent from my x10 on gingerbread
Lion3494 said:
Also post in the right thread next time
Sent from my x10 on gingerbread
Click to expand...
Click to collapse
you mean forum. he needs to post a thread on the correct forum
Hi, everyone I just joined this forum. I have X10i with firmware 2.1. While searching the thread i came acrosss terms like root, xrecovery, flashing, MT, generic etc. Can someone help me out what these terms mean. I wanted to upgrade my phone to gingerbread. Previously I am an iphone user So i am total noob to this OS and the phone
Thanks in advance
good get away from iphone
root--same thing as jailbreak
xrecovery-- a badass tool that lets you flash roms onto your phone.
flashing-- umm... it is like installing a modified version of even the legit version on the device
generic-- A product having no brand name or registered trademark
example= for device there is branded or non branded
branded means that a company like ATT or Rogers approves that firmware or OS version. So when you turn your phone on, you will usually see something related to them. like an animation of the att world
generic--- clean install. no company restrictions. just regular
ok links for all that crap above
2.3.3 firmware (does not matter if you download x10a or x10i)
Generic-----
http://forum.xda-developers.com/showthread.php?t=936733
do yourself a favor and read
http://forum.xda-developers.com/showthread.php?t=936733 before and download the program WINDOWS only
Thanks for your help. I am going to upgrade my phone soon so is their any problem in doing so and by the way should i just use the SEUS or flash tool
angel eyes said:
Thanks for your help. I am going to upgrade my phone soon so is their any problem in doing so and by the way should i just use the SEUS or flash tool
Click to expand...
Click to collapse
Either will do.
ok thanks for the advice going for the upgrade now lets hope everything goes smoothly will post the results
Now this is the end result of upgrading my phone I used SEUS to upgrade my X10i the phone went into flash mode and the SEUS detect that new software is available soit downloads it but when it comes to installing it stopped at about 15% and said that updATE cannot continue check battary is fully charged and than again try. As far is i remember phone was fully charged when i put it for update now what should i do. The phone doesnt restarts now and when I power up my phone only th egreen led blinks and it vibrates for split second than nothing I waited for it but the phone is not responding what should i do now
HELP NEEDED
to tell you the truth i dont know what SEUS is
i think it is for drivers or something but you should use PC comapanion for drivers
ok
use flashtool in the first link i gave you and download one of the 2.3.3 files
or use a 2.3.3 rom
and flash the sucker on
it should work
Try flashtool if doesn't work let your phone on charge for 1 hour and take it off try again whit seus should be good to go
Sent from my X10i using xda premium
Thanks for the help guys now i have downlaoded flashtool 0.2.8, 2.9,3.0 i also downloaded the firmware and did all the steps according to the toturiol but that what happens it detect the phone in flash mode the flashing starts but at fato1.sin it gives as error message "error flashing abort". I also tried other firmwares but the same error.
Now guys I think I am great trouble so need help
What to do next
And I used the desktop charger to charge the battery for whole two houra but SEUS gives the same error plus pc companion gives error as well i am stuck
Go to pc application manager, close seus and pc companion. Try flashtool tool once again http://forum.xda-developers.com/showthread.php?t=928343. I hope this work for you.
Sent from my SO-01C using Tapatalk
Ok i will try that one too thanks alot lets see wat happens
ok tried that too nu luck
What should i Do now One thing more i was goignaround the threads looking for solution So in one thread it said that firmware can ber installed through flash tool 0.2.5
I tried that too and amazingly the flashing goes all the way to the end on 0.2.5 in the end i get the msg that flashing complete and remove the phone but when i remove the phone and turn it on it just vibrates and small blip of green flash led than nothing
What could be the problem
1. Download Flashtool from
http://doomlord.sylvester20007.com/x10/x10_gb/FlashTool_0.2.9.1-GBready_root_xRec.exe
2. Download the generic 2.3 ROM of your choice
http://forum.xda-developers.com/showpost.php?p=11038646&postcount=1
Personally I would get the Global version unless you can find your country specific one.
Global version download - http://www.multiupload.com/JEXUAHAZTL
3.
a) connect your phone to your PC, make sure it installs the drivers (if your Sony software is working it is fine)
b) Extract Flashtool into a directory you know
c) Extract the firmware file you downloaded. And move the ftf file into the "firmware" directory of Flashtool
d) Make sure your phone is not connected to the PC and is off.
e) Run Flashtool, click on Flash and select the firmware you have just downloaded.
f) It will give you the same instruction - holding the "back" key, (phone still off) connect it to the PC. If you did this correctly, the light will be green and it will start flashing your phone.
g) After it is completed, reboot your phone once or twice and check that it is working.
4. Installing xrecovery and rooting refer to instructions (you already have all the files from when you download in step 1)
http://forum.xda-developers.com/showthread.php?t=1196808
Let me know when you have completed the steps above.
Thanks for advice downloading it now and going to try and will let now about the results
sasukewa said:
1. Download Flashtool from
http://doomlord.sylvester20007.com/x10/x10_gb/FlashTool_0.2.9.1-GBready_root_xRec.exe
2. Download the generic 2.3 ROM of your choice
http://forum.xda-developers.com/showpost.php?p=11038646&postcount=1
Personally I would get the Global version unless you can find your country specific one.
Global version download - http://www.multiupload.com/JEXUAHAZTL
3.
a) connect your phone to your PC, make sure it installs the drivers (if your Sony software is working it is fine)
b) Extract Flashtool into a directory you know
c) Extract the firmware file you downloaded. And move the ftf file into the "firmware" directory of Flashtool
d) Make sure your phone is not connected to the PC and is off.
e) Run Flashtool, click on Flash and select the firmware you have just downloaded.
f) It will give you the same instruction - holding the "back" key, (phone still off) connect it to the PC. If you did this correctly, the light will be green and it will start flashing your phone.
g) After it is completed, reboot your phone once or twice and check that it is working.
4. Installing xrecovery and rooting refer to instructions (you already have all the files from when you download in step 1)
http://forum.xda-developers.com/showthread.php?t=1196808
Let me know when you have completed the steps above.
Click to expand...
Click to collapse
I have done it as adviced but no luck flashing aborts in the middle and giving error message now wehat should i do
Do you have the new flash tool?
angel eyes said:
I have done it as adviced but no luck flashing aborts in the middle and giving error message now wehat should i do
Click to expand...
Click to collapse
Can u do a screen shot or tell us what the error message is?
Thx.
Dark Nightmare said:
Do you have the new flash tool?
Click to expand...
Click to collapse
I have flash tool 0.2.5,0.2.8,0.2.9,0.3.0
Have tried them all only 0.2.5 goes all the way to the end but when i turn on the phone it only virbrates and green led flashes for sec than nothing
When you reboot is there anything showing on the screen? Sony logo...anything? If yes, wait it can take a long time for a new rom to install. If no, I think you need to revert back to the 2.1 rom, root and install busybox, superuser, and xrecovery. once thats done you can backup your rom and data so you don't get stuck updating or if you have trouble with a custom rom etc. Also I think your battery stats should be wiped using xrecovery, it sounds like SEUS checked this and the file said your battery was too low to continue the update. Here is a good place to start.
http://forum.xda-developers.com/showthread.php?t=928343&highlight=flashtool+for+noobs
Here is a video on youtube that may help too:http://www.youtube.com/watch?v=HmX-IYNYqL8
Hope this helps you, Good Luck.
angel eyes said:
I have flash tool 0.2.5,0.2.8,0.2.9,0.3.0
Have tried them all only 0.2.5 goes all the way to the end but when i turn on the phone it only virbrates and green led flashes for sec than nothing
Click to expand...
Click to collapse
Try taking the battery out and then try flashing again. Which ftf file are you flashing or selecting in the flash program. You need to use at least a 0.2.9 version of the flashtool.... if you use 0.2.5 start with the 2.1.54 ROM first.
hi guys dis s d tutorial for flashing d stock firmware on a dead or bricked x10 mini.....
NOTE: THIS PROCESS WILL RELOCK UR BOOTLOADER AND ROOT WILL BE GONE
Step 1: Download Sony Ericsson update service software (SEUS) http://www.sonyericsson.com/cws/supp...ro?cc=gb&lc=en
Step 2: Install it and open it
Step 3: Now do a hot reboot on the device by pressing and holding both the menu and power keys at the same time
Step 4: Without wasting even a single second press and hold the back button and connect your USB cable while holding Back
Step 5: Do not release the back key until the SEUS identifies your device. When it identifies your device, the update option will appear on your screen.
(It may say that you have a latest firmware already, but you click repair anyway and after the operation starts, You may release your back key.
Step 6: Wait until the update process gets finished and reboot your device now you will have a stock firmware with locked bootloader
feel free to hit thanks if this helped you..
kudo for posting this, but many spelling mistakes and excessive use of txt speak like "ur, u, diz" you may wanna rewrite the post
---------- Post added at 10:14 AM ---------- Previous post was at 09:17 AM ----------
Step 1: Download Sony Ericsson update service software (SEUS) http://www.sonyericsson.com/cws/sup...ject/pccompanion/xperiax10minipro?cc=gb&lc=en
Step 2: Install it and open it
Step 3: Now do a hot reboot on the device by pressing and holding both the menu and power keys at the same time
Step 4: Without wasting even a single second press and hold the back button and connect your USB cable while holding Back
Step 5: Do not release the back key until the SEUS identifies your device. When it identifies your device, the update option will appear on your screen.
(It may say that you have a latest firmware already, but you click repair anyway and after the operation starts, You may release your back key.
Step 6: Wait until the update process gets finished and reboot your device now you will have a stock firmware with locked bootloader
Hopefully, this will be easier to understand (spelling, grammer & punctuation fixed)
thanx for the opinion will repost it soon
You are wrong, restore a firmware does not restore the lock of the bootloader. Your bootloader keeps unlocked always (you need s1tool to relock)
Sent from e10a using xda premium
if the phone is bricked... will the above steps work..??
i want to flash my stock kernel with nAa kernel and install MiniCM7..
Please someone reply... thanks in advance..
karthiks.840 said:
if the phone is bricked... will the above steps work..??
i want to flash my stock kernel with nAa kernel and install MiniCM7..
Please someone reply... thanks in advance..
Click to expand...
Click to collapse
any one will answer this question ??
matthias1203 said:
any one will answer this question ??
Click to expand...
Click to collapse
The phone at least has to be able to boot in flash mode. If it's "more bricked than that" it shouldn't work...
Missing "REPAIR" option in SE Update Service
SE Update Service ver.: 2.12.5.57 (last)
Kernel: nAa kernel
ROM: MiniCM7
There is no "REPAIR" option (see attachment).
It was in older version only? Who knows?
Or does anyone know another way to get back to stock ROM and kernel from the kernel and naa MiniCM7 ROM?
I claim my phone. So I need the original state.
THNX a LOT!
The repair option in PC Companion is a bit hidden, mine is in dutch but i try to show you the steps you have to take.
See screenshot 1, support zone, click start
See screenshot 2, update phone software, click start
See screenshot 3, phone not found (or you have the latest firmware), click the repair link
The repair link is not there if you choose update from the mainscreen in SEUS.
This desnt work. I have got almost standard conditions
SmG67 said:
The repair option in SEUS is a bit hidden, mine is in dutch but i try to show you the steps you have to take.
See screenshot 1, support zone, click start
See screenshot 2, update phone software, click start
See screenshot 3, phone not found (or you have the latest firmware), click the repair link
.
Click to expand...
Click to collapse
Your screenshots are from Sony PC Companion
But there is talk about Sony Ericsson update service software (SEUS)
showstopper1 said:
Step 1: Download Sony Ericsson update service software (SEUS) http://www.sonyericsson.com/cws/supp...ro?cc=gb&lc=en
Step 2: Install it and open it
Click to expand...
Click to collapse
Nevertheless I try your way. I found "Repair" link. I walk thru all steps, but It shows "No software available" (it was looking more like "update" then "repair") (see attachment). And then redirect me to homepage of PC Companion (with no chance to Repair).
I have got standard conditions:
Sony XPERIA X10 mini (E10i)
with
Kernel: nAa kernel (last version)
ROM: MiniCM7 (last version)
PC Companion Version: 2.10.053 (last)
SE Update Service (SEUS) Version: 2.11.12.5 (last)
THIS SOLUTION STILL DOESNT WORK FOR ME (I THINK FOR ANYBODY WITH SAME CONDITIONS)
Please help. I'm starting to be clueless :/
Thanx a lot.
I have edited my post, it is PC Companion ofcourse...
What steps did the repair option make you take? with me it is:
1. you will lose all your data, agree...
2. computer will be prepared, choose your model - x10 mini
3. it will tell you how to enter flash-mode (unplug, shut down, press back, plug in)
4. it will download the firmware and flash it to the phone
5. disconnect the phone and restart
as far as i know, the repair option doesn't care what phone you have, or what software it runs, it trusts you to select the right model, and itself to find the right firmware for that, no other checks are performed, it just flashes it.
PS: I was on nAa-08 and GingerDX this time, especially for this post i have flashed back to stock. i have bricked my phone a few times when i tried flashing custom roms and it always worked this way for me, even if you are on stock firmware it will still flash it again.
is it possible that my mobile SIM is not recognized after bootloader relock in s1tool?
niksa09 said:
is it possible that my mobile SIM is not recognized after bootloader relock in s1tool?
Click to expand...
Click to collapse
If it was still working after you unlocked the bootloader, then relocking it probably won't break it.
If it stopped working after you unlocked the bootloader, then relocking might restore it.
In any case make sure you're on stock firmware before you relock.
guys i have a bricked mini with stocked firmware i connect it with seus and it says that i have the latest firmware but it doesnt appear the repair button ! Whats can i do /
marios199546 said:
guys i have a bricked mini with stocked firmware i connect it with seus and it says that i have the latest firmware but it doesnt appear the repair button ! Whats can i do /
Click to expand...
Click to collapse
leave your phone unplugged when you choose update, and only plug it in when it asks to connect in flashmode. It can't recognise your phone when it's unplugged and should give you the repair option, if SEUS doesn't do that, download PC Companion, that will do it.
but the pc companion need the phone to be turned on and my phone doesnt turn on
---------- Post added at 10:35 AM ---------- Previous post was at 10:32 AM ----------
i follow your instructions and again nothing
marios199546 said:
but the pc companion need the phone to be turned on and my phone doesnt turn on
---------- Post added at 10:35 AM ---------- Previous post was at 10:32 AM ----------
i follow your instructions and again nothing
Click to expand...
Click to collapse
So, what is wrong with your phone then? is your battery dead?
When you start PC Companion and you don't have your phone plugged in, you do the following:
Choose update
It will say: Phone not recognised (or something like that) and in that dialog there is a little blue link saying Repair. Click on it.
It will tell you you will lose all user data, accept that
It will ask you to select your phone-model from a list
It will download the firmware for that phone.
It will ask you to connect your phone in flash-mode (press the back-button, plug in the usb-cable, the led will turn green, the dialog will disappear and it will start flashing.
No need to turn on your phone at all, but it needs some charge in the battery in order to successfully complete the flash (normally a charge of over 50% is recommended to be safe)
please help me find goog firmware for my xperia mini (e10i)
my xperia mini bricked after i tried to flash firmware but it still boot to flashmode. please help me find a better firmware to restore my phone!
I bought the phone over the mexican equivalent of ebay, it came with 4.0.2.A.0.58 firmware which is android 2.4.3, once i connected to wifi the phone prompted me with an OTA update to 4.0.2.A.0.62, i accepted it and when it finished the download and rebooted it never came on, i tried removing the battery, holding the button for a long time but nothing worked, after some reading i downloaded the SEUS tool, it detected the phone fine and downloaded a 230mb file which i assume was the latest FW, it said that the installation was sucessful and that i should turn on my phone, again it didn't turn on, it vibrates but the screen never comes on, after giving up on SEUS i read about flashtools, i downloaded the previous firmware that i had which was 4.0.2.A.0.58, the one that was working fine before the OTA, file name is
SK17i_4.0.2.A.0.58_GLOBAL.tft
I start flashtools and select the firmware, phone is detected fine but the flashing gets stuck at
Processing system.sin
Checking Header
Flashing data
i left it running for 30 mins and it didn't move from there, the person that sold it to me says the phone is new and says that it is my fault that the phone doesn't work anymore because according to him he asked in an email not to update the phone or the warranty was void with him, i live in mexico so there's not a sony center i can go for help, i really want to fix the phone, was pretty excited about getting it and now it wont turn on
what can i do next?
arosemena said:
I bought the phone over the mexican equivalent of ebay, it came with 4.0.2.A.0.58 firmware which is android 2.4.3, once i connected to wifi the phone prompted me with an OTA update to 4.0.2.A.0.62, i accepted it and when it finished the download and rebooted it never came on, i tried removing the battery, holding the button for a long time but nothing worked, after some reading i downloaded the SEUS tool, it detected the phone fine and downloaded a 230mb file which i assume was the latest FW, it said that the installation was sucessful and that i should turn on my phone, again it didn't turn on, it vibrates but the screen never comes on, after giving up on SEUS i read about flashtools, i downloaded the previous firmware that i had which was 4.0.2.A.0.58, the one that was working fine before the OTA, file name is
SK17i_4.0.2.A.0.58_GLOBAL.tft
I start flashtools and select the firmware, phone is detected fine but the flashing gets stuck at
Processing system.sin
Checking Header
Flashing data
i left it running for 30 mins and it didn't move from there, the person that sold it to me says the phone is new and says that it is my fault that the phone doesn't work anymore because according to him he asked in an email not to update the phone or the warranty was void with him, i live in mexico so there's not a sony center i can go for help, i really want to fix the phone, was pretty excited about getting it and now it wont turn on
what can i do next?
Click to expand...
Click to collapse
Well there must be a problem with the phone already.
Or else why would the seller say "not to upgrade"?
Flashtool was the only option that i would have recommended.
But you say it didnt work.
Are you sure you put the phone in flash mode?
---------- Post added at 09:23 AM ---------- Previous post was at 09:21 AM ----------
And by the way, it takes time for the phone to turn on after an update.
Leave it for a while and see if it opens or not.
coolancool said:
Well there must be a problem with the phone already.
Or else why would the seller say "not to upgrade"?
Flashtool was the only option that i would have recommended.
But you say it didnt work.
Are you sure you put the phone in flash mode?
---------- Post added at 09:23 AM ---------- Previous post was at 09:21 AM ----------
And by the way, it takes time for the phone to turn on after an update.
Leave it for a while and see if it opens or not.
Click to expand...
Click to collapse
Yes, i've tried with 3 different ftf files and they all get stuck in system.sin when flashing, this really sucks
arosemena said:
Yes, i've tried with 3 different ftf files and they all get stuck in system.sin when flashing, this really sucks
Click to expand...
Click to collapse
Have you asked the person from whom you bought the phone whether the bootloader of the phone is locked or unlocked?
I ask this because the people with unlocked bootloader are advised not to accept ota updates as it will brick their devices.
Sent from my Xperia Mini Pro using Tapatalk 4 Beta
andogeek10 said:
Have you asked the person from whom you bought the phone whether the bootloader of the phone is locked or unlocked?
I ask this because the people with unlocked bootloader are advised not to accept ota updates as it will brick their devices.
Sent from my Xperia Mini Pro using Tapatalk 4 Beta
Click to expand...
Click to collapse
You can't possibly update OTA with an unlocked bootloader it would get downloaded but it wont update.
coolancool said:
You can't possibly update OTA with an unlocked bootloader it would get downloaded but it wont update.
Click to expand...
Click to collapse
It's possible, but it'll brick your device.
Sent from my Xperia Mini Pro using Tapatalk 4 Beta
andogeek10 said:
It's possible, but it'll brick your device.
Sent from my Xperia Mini Pro using Tapatalk 4 Beta
Click to expand...
Click to collapse
No it doesn't!
The phone will switch back to normal and a notification says:- OTA upgrade failed
andogeek10 said:
It's possible, but it'll brick your device.
Sent from my Xperia Mini Pro using Tapatalk 4 Beta
Click to expand...
Click to collapse
maybe it was this, is there any way to unbrick it?, this is my first android phone, i had no clue this could happen
EDIT:
i think i unbricked it, i managed to get the screen to show by flashing with this
http://forum.xda-developers.com/showthread.php?t=1553601
i'll update once i get a firmware working
EDIT 2:
still getting stuck on system.sin when trying to flash it , is there any way i can get the original update to work?
this show in the flashtool
INFO - Current device : SK17i - BX902JQK2V - 1250-0861_R13D - 1244-7088_4.0.2.A.0.58 - WORLD-i_4.0.2.A.0.58
arosemena said:
maybe it was this, is there any way to unbrick it?, this is my first android phone, i had no clue this could happen
Click to expand...
Click to collapse
NO! IT doesn't get bricked!
I had an unlocked bl too i upgraded OTA but it wasn't successful.
However,my phone switched back on and the notif. said OTA upgrade failed or sumthng like that.
coolancool said:
NO! IT doesn't get bricked!
I had an unlocked bl too i upgraded OTA but it wasn't successful.
However,my phone switched back on and the notif. said OTA upgrade failed or sumthng like that.
Click to expand...
Click to collapse
6. Turning the "brick" into a smartphone
If you had unlocked bootloader and did OTA(Over the Air) update, then you probably ended up with a dead phone, aka brick. Don't worry, it is not completely bricked, still can be saved!
Download UnbrickingXperia2011.zip file from this post below.
Unpack the .zip file and place the .ftf file in Flashtool\firmwares folder.
Open Flashtool.
Get your phone to flashmode, make sure it is turned off, press down Volume DOWN button and connect USB cable.
In Flashtool, click the lightning button, pick Flashmode and choose the Xperia_2011_FreeXperia_ALL.ftf file.
Let Flashtool finish.
Install stock firmware and kernel to your phone.
Remove USB cable from your phone and start your phone.
Try not to brick it again, less problems for you.
Click to expand...
Click to collapse
From the Q6. of this thread - http://forum.xda-developers.com/showthread.php?t=1568792
You are very lucky if you did not brick your phone.
arosemena said:
I bought the phone over the mexican equivalent of ebay, it came with 4.0.2.A.0.58 firmware which is android 2.4.3, once i connected to wifi the phone prompted me with an OTA update to 4.0.2.A.0.62, i accepted it and when it finished the download and rebooted it never came on, i tried removing the battery, holding the button for a long time but nothing worked, after some reading i downloaded the SEUS tool, it detected the phone fine and downloaded a 230mb file which i assume was the latest FW, it said that the installation was sucessful and that i should turn on my phone, again it didn't turn on, it vibrates but the screen never comes on, after giving up on SEUS i read about flashtools, i downloaded the previous firmware that i had which was 4.0.2.A.0.58, the one that was working fine before the OTA, file name is
SK17i_4.0.2.A.0.58_GLOBAL.tft
I start flashtools and select the firmware, phone is detected fine but the flashing gets stuck at
Processing system.sin
Checking Header
Flashing data
i left it running for 30 mins and it didn't move from there, the person that sold it to me says the phone is new and says that it is my fault that the phone doesn't work anymore because according to him he asked in an email not to update the phone or the warranty was void with him, i live in mexico so there's not a sony center i can go for help, i really want to fix the phone, was pretty excited about getting it and now it wont turn on
what can i do next?
Click to expand...
Click to collapse
At first unbrick ur phone by the following xda link u given.i think ur ftf file is corrupted.so flash another ftf file for which is for ur device.don't flash any other device's ftf file.try ics firmware .431 or .587. Or u can try any other custom rom.
Last month my lww bricked by receiving ota update.my bootloader is unlock.then I unbrick through the link you mentioned.i confirmed that if ur device is unlocked then it will work for u also.
Sent from my WT19i using xda app-developers app