Related
Hello.
I have a problem I hope someone here can help me to solve..
I have an Orange SPV M3100 that hangs on the Windows Mobile screen when I try to start it.
I'm able to go into bootloader mode, and i have tried using mtty142.exe with the set 14 0 command. It still won't boot. I've also tried to hard reset it.. still won't boot..
What I did was trying to unluck the SIM-lock with the Universal unlocker (HTC_Uni_Unlock_v1) from buzz. At the time I thought universal meant that it worked on all HTC devices (stupid, I know)... And I also thought it was harmless to just try and see if it worked. But I got an error around 92-93% and after that my device won't start. So my radio ROM might be screwed.
I'd like to flash my ROM with the i-mate one (JASJAM_WWE_1.20.305.3_1.20.305.104_1.07.03.10_ship.exe) and then add the ext-rom. But how do I do that when I can just access the bootloader screen? And do you think it will boot again if I'm able to flash it?
Here's some more info about my device:
HERM100
IPL-1.01
SPL-1.04
Thank you very much in advance. Help will be highly appreciated.
No your rom *is* screwed. You can get into bootloader, you can even get to 11% of a dopod etc rom upgrade if you try, but you will not flash a new radio.
You CAN boot the device.
Do a hard reset, but do not press spacebar to reboot after. Instead, do a soft reset. The unit should boot but as you've screwed the radio you will not get a gsm signal and the phone will say unknown sim status.
I know this as I bought one cheap after the owner had done exactly the same as you.
IMEI-check's unlock solution is the only one that works IIRC, and in some cases this re-writes the security area of the phone and repairs similar issues, but in this case I could not get the prog to read.
You need to return the device to HTC - you'll need to pay approx £35 for reflashing back to the orange rom. This is what I had to do.
Currently you cannot book the m3100 in through the web as it's too new, instead email / call them.
http://service.htceurope.com/
edit - or if you're an orange customer ring 150 and act dumb saying it ' won't work'.... :wink:
Richard
What happens if you just leave the phone in bootloader mode and then try to flash any ROM (imate, dopod, htc...)? run 2 times the RomUpgradeUt.exe if you get an error on the 1st try.
If you get an error while running the rom upgrade utility you can monitor the USB port while upgrading (you will see the real error from the bootloader then), there's some more info on this wiki page:
http://wiki.xda-developers.com/index.php?pagename=Hermes_BootLoader
good luck
pof said:
What happens if you just leave the phone in bootloader mode and then try to flash any ROM (imate, dopod, htc...)? run 2 times the RomUpgradeUt.exe if you get an error on the 1st try.
If you get an error while running the rom upgrade utility you can monitor the USB port while upgrading (you will see the real error from the bootloader then), there's some more info on this wiki page:
http://wiki.xda-developers.com/index.php?pagename=Hermes_BootLoader
good luck
Click to expand...
Click to collapse
No, if you want to send it back under warranty do not try to run a rom update as there are no orange rom packages. As described in my post above, it will get to 11% and stop. The device will be in the same state as before, with the same ext rom, but the splash screen and bootloader will have changed.
i.e: it will be bloomin obvious you tried flashing it and failed. Not what you want if you try for a warranty repair....
There is no error from the bootloader - as there is no radio rom present and no security area the upgrade process just hangs.
Richard
fluffcat1 said:
No, if you want to send it back under warranty do not try to run a rom update as there are no orange rom packages.
[...]
i.e: it will be bloomin obvious you tried flashing it and failed. Not what you want if you try for a warranty repair....
Click to expand...
Click to collapse
That's true, do not try to flash any other roms if you want to use the warranty or send the device back...
Thank you very very much for your help guys.
As I'm the administrator of these devices in the company I work for I just grabbed a new SPV and will send this thing back to Orange. It sounded like I'm getting a new one..
Well, I think I've learnt my lession.
Oh, and I have another question. Is there a reg editor I can install on this one so I can remove the app lock? I know I can install java apps, but it's a bit grumpy about apps that needs installation (the developer must be certificated).
Cheers guys.
Hi,
Try to flash a new rom using the SD card method described here:
http://forum.xda-developers.com/viewtopic.php?t=62596
The rom must match your CID. Let us know if it works
pof said:
Hi,
Try to flash a new rom using the SD card method described here:
http://forum.xda-developers.com/viewtopic.php?t=62596
The rom must match your CID. Let us know if it works
Click to expand...
Click to collapse
Errr, did you read the last post? He sent it back......
Richard
I just wanted to let him know there's a possible solution, it just in case he still has the unit
pof said:
I just wanted to let him know there's a possible solution, it just in case he still has the unit
Click to expand...
Click to collapse
Maybe his search is broken as well as his old phone eh?.... :roll:
fluffcat1 said:
You need to return the device to HTC - you'll need to pay approx £35 for reflashing back to the orange rom. This is what I had to do.
Click to expand...
Click to collapse
Sorry to take the thread a bit OT, but just wanted to confirm this again.
So, if I flashed my M3100 with a different ROM, and then had to return the phone to Orange for repair for a different reason, I can send it back to HTC just to have the ROM reflashed, and then send the phone to Orange to get the repairs done?
I've been hesitating on whether to flash the phone with a non-Orange ROM because I didn't want to give up the ability to obtain warranty repair (as there is no ROM upgrade yet). If it's just a matter of £35 and then everything else as normal, maybe it's not so bad...
Thanks!
My SPV M3100 won't start!!!
I also did this, so if anyone can find a solution it would be greatly appreciated.
Also tried this and it didn't work for me:
Try to flash a new rom using the SD card method described here:
http://forum.xda-developers.com/viewtopic.php?t=62596
"I have a problem I hope someone here can help me to solve..
I have an Orange SPV M3100 that hangs on the Windows Mobile screen when I try to start it.
I'm able to go into bootloader mode, and i have tried using mtty142.exe with the set 14 0 command. It still won't boot. I've also tried to hard reset it.. still won't boot..
What I did was trying to unluck the SIM-lock with the Universal unlocker (HTC_Uni_Unlock_v1) from buzz. At the time I thought universal meant that it worked on all HTC devices (stupid, I know)... "
rachelm700 said:
I also did this, so if anyone can find a solution it would be greatly appreciated.
Also tried this and it didn't work for me:
Try to flash a new rom using the SD card method described here:
http://forum.xda-developers.com/viewtopic.php?t=62596
"I have a problem I hope someone here can help me to solve..
I have an Orange SPV M3100 that hangs on the Windows Mobile screen when I try to start it.
I'm able to go into bootloader mode, and i have tried using mtty142.exe with the set 14 0 command. It still won't boot. I've also tried to hard reset it.. still won't boot..
What I did was trying to unluck the SIM-lock with the Universal unlocker (HTC_Uni_Unlock_v1) from buzz. At the time I thought universal meant that it worked on all HTC devices (stupid, I know)... "
Click to expand...
Click to collapse
the above link doesnt work?
zohaer21 said:
the above link doesnt work?
Click to expand...
Click to collapse
IIRC it is this link on the new forum:
http://forum.xda-developers.com/showthread.php?t=277281
spv m3100 don't start
hello guys
I have the same problem about spv m3100. I used "universal unlock tool" to unlock my device and now it don't start,don't boot...I tried the Hermes SD Card flashing methods with qtek001 rom and, a white screen with "loading...." appears for 2 second and then nothing else appened. I think that the method is right but I need to use a different software. what do you think about?
please help me
thankksssss
My SPV M3100 won't start
SD card method is no good as there is no upgrade from Orange until January.
Tried to do a radio upgrade explained here:
http://wiki.xda-developers.com/index.php?pagename=Hermes_ExtractedRadioRoms
But it didn't work just came up with connection error, tried to monitor USB but nothing showed up to find out why, althouth mtty commands always do show up in USB Monitor.
Still have a brick and looking for a solution, hopefully, someday, please someone help me I am loosing my mind.
Hello
How to enter boot mode on HTC 200 ?
My htc hangs on HTC screen.
I'm trying to reflash it.
Thanx
Chris
@chrisro, Please read the wiki:
http://wiki.xda-developers.com/index.php?pagename=Hermes_UpgradeProblems
http://wiki.xda-developers.com/index.php?pagename=Hermes_Resets
Thank you very much.
Greets form Poland !
Chris
I have a 8125 G4 sim unlocked w lokiwiz and a flashed WMSE5_rev4 with soft spl, well the problem that i have now is that i recentley tried to flash a new wm6 rom without hard spl ( yeah i know stupid) And now i am stuck on tri color boatloader screen no matter if i turn it off or not still goes back to the same thing. and yes the rom that i was flashing was g safe, i think were i messed up is not CID unlocking it with hard spl?when i tried to flash the new rom it went all the way to 100% and then gave error after that. NO activesync connection right now
questions
1- DID I BRICK IT
2- is there a way to recover this device
unlock it again. (CID) i had the same thing on my wiz g4. and no. is not bricked.
ok thank you and i will let u know what happens so i should use hardspl right?
ok thank you and i will let u know what happens so i should use hardspl right?
still lost
Ok this is where im at i have tried to flash other roms, NOTHING. the phone is cycling between charging(when on charger) and bootloader every few seconds then i pull it off and nothing. i cant get hard spl to recognize the phone nor will activesync. i understand that i need to CID unlock the phone but i cant even get that far?
any suggestions? please walk me through it im not stupid but HTC's are a whole new ball game for me. im used to motorolas(by the way they suck!)
thanks in advance
Get the original stock ROM for your Wizard version and flash it to get your OS back, then you can HardSPL or SoftSPL.
p.s. G4 Wizard does not have free solutions to actually "CID unlock". Either HardSPL and SoftSPL are hacks that tricks the RUU to allow flashing, you will still see your device as Locked in WST(Wizard Service Tool).
go to activesycn settings turn OFF allow usb connections and retry
I read it here in another thread after I returned My P4300 to cincinati bell in exactly the same condition you described.
Good Luck
hello
i got my hermes and runned the unlocker procedure 3a,
it was working fine for over 6 months,
suddenly it wasn't receiving any signal , and now i am getting the message "no gsm" at the boot time.
I tried flashing another OS rom and worked fine.
but i cannot flash any radio rom. Whenever i try to flash a radio rom, the phone "Brakes" and stucks on the boot (3 colour) screen. And i cannot flash any radio rom, it does not accept anything, the only thing that accepts is the OS rom.
but again after flashing radio it crashes again and stucks at the 3 colour boot screen.
can anybody help me?
i tried running this procedure http://wiki.xda-developers.com/index.php?pagename=Hermes_UpgradeProblems#problem5
but it didn't solve my problem.
does anybody have any idea?
try this
http://forum.xda-developers.com/showthread.php?t=377389
guys, is there anybody that can help me out with this?
i really don't know what to do.
okay, take a deep breath and relax.... first, as XtreMe_G said check for bad blocks with mtty and repair if necessary.
If I were you I would then try to re-install a stock rom. If that doesnt work maybe try a radio only rom . If that doesnt work, then it looks like the radio has been corrupted. No amount of flashing will repair this. If so, sorry, you are now the proud owner of a PDA but unfortunately it will never be a phone again.
Hope this helps... Cheers...
thanks for your reply,
ultramag69 said:
okay, take a deep breath and relax.... first, as XtreMe_G said check for bad blocks with mtty and repair if necessary.
Click to expand...
Click to collapse
done that, no bad blocks
ultramag69 said:
If I were you I would then try to re-install a stock rom.
Click to expand...
Click to collapse
didn't work
ultramag69 said:
If that doesnt work maybe try a radio only rom .
Click to expand...
Click to collapse
nope, nothing
any other ideas?
hi...
some body help me please where i can get the original rom softbank X01HT?
it seems to me from what u described that your phone is now a shiny brick. the only reason i suggested you checked for bad blocks is cause if i were in your position, i would try everything i could think off before giving in.....hopefully someone else has more ideas of wat to try, cause i'm all out here
Try "set 16 0" (without quotes) using mtty.exe . I am virutally in the same boat as you are. My Hermes radio is corrupted (No GSM) and it semi-bricks to Bootloader when I try to flash a radio ROM. Somehow I was able to Install HardSPL 1.40 when I first got it. That command un-bricked my phone from bootloader.
Hey, my phone is an At&t 8525 and after finally fixing the white screen problem and flashing hard-spl v7 and a couple of roms I bricked the phone when flashing the last touch flo rom. During the flash the ruu wrapper stopped and indicated there was an error. I did the recovery and it supposedly completed succesfully if I can remember right. When it reboot it would not get past boot loader. And thats where I am now, the phone will not get past boot loader.
I've tried every method on these forum I could found
SD card flashing dosent work, I get the 002..... error in red.
Flashing the factory an at&t rom dosent work either, gets the same error
\
As for as I know the MTTY method dosent work, I don't know how to type in commands into bootloader and when I type in 14 0 in MTTY nothing happens
KITL is not enabled
IPL-1.04
SPL-2.03
The phone does not boot into bootloader when I hit the power button, I have to hold the comm button, power button, and soft reset in order to bring up bootloader.
When bootloader is up and the phone is connected to the computer via usb bootloader displays usb on the screen and windows detects the device as an HTC device.
Again i've spent about a week and a half trying to fix this phone and I don't know what to do anymore, i've tried more methods than listed above I can't remember though. If anyone can give me a hint on what to do I would highly appreciate it. Thanks
P.S Can someone please tell me how you type commands in bootloader or MTTY
You DON'T have Hard SPL V7 installed..... Otherwise your SPL would be 2.10.
Connect the Hermes to the pc, make sure active sync has benn disabled - got to settings, untick connect by USB. It should register on the pc. Go to bootloader then run the .nbh file for your stock rom... Make sure its the carrier rom that it was shipped with. It doesn't have to be WM05 but it DOES have to be your ORIGINAL carrier rom. Let it run through, you may gewt lucky.....
If it works, INSTALL HARD SPL V7....... Makes it so much easier to fix then...
Good luck...
Thanks for the reply, much appreciated
I tried downloading and sd card flashing a stock rom from a list of factory roms of all Hermes that I found here on xda. It gave me the same error though. I'm not exactly sure which exact rom to download from that list either. Any more help would be appreciated, thx
Wow I feel retarded, I used the wrong factory rom. After I used the right one it worked perfectly, I now have my 8525 back! Thx so much man, ur the friggin man!
Congrats bro you got it atlast. good luck & take care your baby in future. try to help others with your experience.
Glad you fixed it mate, but if I were you I'd also make sure you have Hard SPL V7 installed. It is the safety net to help when things go wrong... Never gonna be 100% safe but better odds with Hard SPL V7...
SPL - 2.10 oli
Cheers...
Ok... Rejoining the 8525 Clan
Is this Forum still alive???
Been a while guys, figured I would break out the 8525... charge it up and see what kind of things are new in this community. Unfortunately, it looks as if the radio is bricked on it. Seems like it will install ROM's that the radio is not included on. NO GSM is on the boot display, which is strange as I was using this phone until I got the Tilt about 1 1/2-2 yrs ago. I was a hardcore flasher back then... every other day it seemed, so I know it has (or had) everything it needed like the Oli 2.10 SPL... but it seems like I cannot recover this radio issue.
I am messing with the different original OEM and Carrier ROMs hoping I can get passed the 11-12% mark, and I will let you know if something changes. Any idea if un-installing SPL 2.10 Oli, and then trying to walk back through the old SPL steps could help? I am just trying to figure out another way to get around this radio issue... or basically I have a PDA, no phone Damn phone hasn't been touched in like 2 years, you think it would be just as fine as it was when I took the SIM out.
Cheers
Can u plz tell me how do you fix the white screen problem ?????
kashifmehmood said:
Can u plz tell me how do you fix the white screen problem ?????
Click to expand...
Click to collapse
Please try searching before posting.
Your answer lies within
Thread closed
Hi folks! Please help me! I killed tons of nerves because of this phone!
So here is my sad story. 1 Year ago i bought second hand HTC HD2. Seller told me that phone is locked to T-mobile(Not US one!! UK one!! Transaction was held in UK). After I got phone I rushed home to install Android and I was successful at this point. Then I bought a unlock code from ebay, so I Finally could make phone calls. Then I realized that the only way I can insert code is putting back WM 6.5. And here the worst part starts. I read hundreds of manuals but still was unsuccessful. I downloaded many official WM 6.5 ROM installers but they didn't flash my phone. They just got stuck at 0% and error pops up. I was trying it for a week and then I just raged and put phone to the shelf and was waiting til I get will power to start over again.
I hear that every phone needs its own ROM installer for particular region and operator but I couldn't find UK T-mobile ROM so used many others and it didn't help.
I also heard that by IMEI it is possible to find to what operator the phone is locked(just to check if seller didn't lie me) but again I didn't manage to do so.
Here is my IMEI 354120035834066
Please experts help me, little nooby, with this horrible situation.
thank you
Many people report that you can in fact put the code in under android after all,,,, perhaps its only earlier versions that couldn't. That being said you probably want to put a new one on since it (and magldr) will be old versions.
Anyway, all that hanging at 0% is because there is no hspl installed.
Plenty of places to get tmo stock rom,, go put
3.14 ruu Leo tmo uk
.....into Google. When I just did it the real htc site came up second.
Its not necessary, tho,,
Phone into bootloader,
connect USB
Use hspl4 to set 3.03.hspl
Return to bootloader
Flash any 3.14 rom USING USB,NOT SD CARD
Done.
samsamuel said:
Many people report that you can in fact put the code in under android after all,,,, perhaps its only earlier versions that couldn't. That being said you probably want to put a new one on since it (and magldr) will be old versions.
Anyway, all that hanging at 0% is because there is no hspl installed.
Plenty of places to get tmo stock rom,, go put
3.14 ruu Leo tmo uk
.....into Google. When I just did it the real htc site came up second.
Its not necessary, tho,,
Phone into bootloader,
connect USB
Use hspl4 to set 3.03.hspl
Return to bootloader
Flash any 3.14 rom USING USB,NOT SD CARD
Done.
Click to expand...
Click to collapse
Thank you, but always when I am trying yo install HSPL4 critical error comes up. I think it comes up because I have spl 2.1000000 which should be 2.08 I found information that in order to downgrade to 2.08 I need to flash official ROM. But when I am trying to do so it is always stuck on 0%...
I am so $%^& up ...
any ideas?.... thx
Does HSPL4 not allow you to install 3.03 to your device ?
T-Mobile UK ROM is available direct from HTC site:
http://www.htc.com/uk/help/htc-hd2/#download
Mister B said:
Does HSPL4 not allow you to install 3.03 to your device ?
T-Mobile UK ROM is available direct from HTC site:
http://www.htc.com/uk/help/htc-hd2/#download
Click to expand...
Click to collapse
Hi. Thanks for ROM, but still.. got stuck on 0% and doesn't go further..
When I try to install HSPL4 it always gives me critical error...
Fixed my problem. Now everything works fine!! Thank you very much guys!!
how ??
rom4eg said:
Fixed my problem. Now everything works fine!! Thank you very much guys!!
Click to expand...
Click to collapse
explain