Related
Right, i'd appreciate any help you guys can give me, especially if it means i don't have to spend money.
My XDA fell about a foot off my bved onto a capeted room, it's fine but now there's a line going straight down the middle of it. then the screen flickers and the whole right of the screen is covered with vertical lines then it goes back to being just the one line in the middle.
Now i'm guessing that a new screen would sort that out instantly but say i didn't have £150.20 lying around, anyone got any suggestions?
Thanks loads guys
small suggestion
my two cents worth:
all LCDs are connected by some sort of ribbon connector to the main board of a unit, my experience with nokia celphones INDICATES that some lines in the LCD do not display due to LOOSE connection between the ribbon connector to the mainboard. Sometimes, we just replace the ribbon and even just push it to the board a little and this seems to solve the problem.
My suggestion to you would be: There is a site that i've seen that sells replacement LCD and glass covers, and its a DO-IT-YOURSELF kit, so get info on how to OPEN your XDA, if youre not fainthearted, then apply a little pressure on the ribbon connection to the mainboard, this may help. OTHERWISE, if you are not a TECHIE, have a service center check that for you, YOU MAY NOT HAVE TO REPLACE THE LCD anyway.
Nice, you wouldn't have te address for the place that sells the screens would you?
Ta
It may be that you have dislodged the cable connecter or the contact connection to the screen, many nokias displayed this same fault and sold millions of screens when all that was needed was either to attend to the connections or remove the elastomer and reverse it, or replace the elastomer. An elastomer is a small rubber block with a row of connecters either side, this is the bridge for the electrical/video lines to the screen. Its worth a look anyway to see if anything obvious has occured.
try searching "Repacement LCD Screens", you might find the shop that sells them, its in a thread here somewehere.
The latest suggestion and mine are almost identical, YES, it may really be the ribbon connector that was PARTIALLY dislodge or looses contact sometime.
Search and ye shall find. hehehe. goood luck. Tell me when you find it and POST the thread here will you, for others with the same problem as you to be helped.
website
OH, heres the website.
http://www.pdasmart.com/pdaphone.htm
thanks, i'm really glad to hear it's probably just the cable, but now the problem is finding the right screwdrivers
lol, seriously i haven't got any screwdrivers the size to open my XDA, and i don't particularly want to send it off to a repair centre, they'd charge me for labour, anyone got any ideas?
You need a t6 torx driver and a flat blade dirver and a small crosshead driver.
Anyone Got a t6 torx driver? because i know i haven't lol. how many people do you reckon would have one?
UPDATE
evening all, just got me T6 screwdriver, i opened my XDA and found what looked like te connector and had a bit of trail and error but it still doesn't completely fix it, any ideas?[/code]
Hi Guys
My name is Luis and I live in Costa Rica. I have a HTC Jade which recently got the LCD screen broken . I really really appreciate if you can name me an Accesories Store located in USA to buy the screen. Since I live in Costa Rica it seems to be the logical place to import. HK is a little bit far from us!
Thank you in advance.
Brando ships worldwide and is pretty reliable. Why not use them?
On ebay.com I found some offers as well, some for about 33USD, like half price as from Brando Shop...
How to Dismantle
Hi,
I also have a broken lcd. I ordered a replacement from brando. Is there a service manual or dismantling guide that shows how to replace the LCD?
TIA
Scary Procedure
Hello! My touch screen is scratched and I bought another one to replace it. Well, it isn't so easy and after I dismantled the device, I decided not to replace it and wait for some tips because no documentation exists. No manual included with the package and no info on the net. (there are some youtube videos for other phones)
After you open the device, you end up with your phone in 3 parts. The Touch screen has a black marquee surrounding it witch I don't know how to remove, and it is connected with the main board with a very very thin wire witch I'm afraid to pull and I'm not sure if I have to pull it or do something else to remove it from the main board. Tips are welcome. Thank you!
since I am not allowed to post links, try following :
use google and type jade lcd dismantling. among pages you will see mikechannon.net, go there and find HTC JADE, click on it and here you are
yianp said:
Hello! My touch screen is scratched and I bought another one to replace it.
Click to expand...
Click to collapse
where did you find the replacement?
Marcell-o said:
where did you find the replacement?
Click to expand...
Click to collapse
I bought one from ebay. Unfortunately no instructions with the package
Kajmaj said:
since I am not allowed to post links, try following :
use google and type jade lcd dismantling. among pages you will see mikechannon.net, go there and find HTC JADE, click on it and here you are
Click to expand...
Click to collapse
Hey Kajmaj THANK YOU SO MUCH!!!!
yianp said:
I bought one from ebay. Unfortunately no instructions with the package
Click to expand...
Click to collapse
i've tried to open the device.
It's not so hard:
AT OWN RISC!!!
Unscrew the 4 screws, click it slightly open.
now you can see on 1 side a small flatcable for the digitizer, unlock it by swapping the behind of the connector. Unplug it.
Flip the PCB and unplug the 2 connectors for the screen and buttons.
Now you can unscrew 2 litle screws at the buttons.
remove the buttons carefully.
Now you can slightly press on the back of the old digitizer untill it loosses.
Place the new one, carefully press on the glue-parts untill you think it is tight enough.
Now read this post backwards to put it all together again.
If you're ready, push the on button.
When it asks for the pincode press : volume up + centerbutton to calibrate.
Et voila.
AT OWN RISC!!!
i'm not responsible for any damage.
Scratched external screen
Hi Marcell-o! I also managed to open it. But the problem is at the last step. the external screen has some kind of black "rubber" that holds it in place. that's where I don't know what to do. I attached a pic to see what I mean.
Thanks for your reply!
yianp said:
Hi Marcell-o! I also managed to open it. But the problem is at the last step. the external screen has some kind of black "rubber" that holds it in place. that's where I don't know what to do. I attached a pic to see what I mean.
Thanks for your reply!
Click to expand...
Click to collapse
You can leave it there.
You have to push at the back of the digitizer.
it's verry tight glued so you have to be patient and careful that you do not break the housing.
The rubber you talk about is meant to leave dust out of there.
i placed my new one just now and it works great.
I made some pictures of the repair and i'll post them tomorrow if i don't forget.
Pictures of the repair
Here are some pictures with some info.
And again:
AT YOURE OWN RISC, I'M NOT RESPONSIBLE FOR ANY DAMAGE!!
before the repair it was like this.
As you can see, it was in a very bad shape.
you can see what i use the most.
The "X" at the upper right corner and the IE scrollbar (yeah thats right, i use Explorer )
When you managed to open the cover you can see at the right side that there is a very small flatcable. (this is the Digitizer cable)
You can open the connector by flipping the handle to vertical.
Use tweezers to unplug it.
Now you can flip the mainboard. As you can see there are 2 more flatcables unplug them with tweezers.
by the way: #1 is for the screen and #2 is for the buttons
Place the mainboard on a safe place so it can't be harmed.
Now the hard part!
Unscrew the 2 very small screws on the red spots and save them on a place where you can find them back again (I lost one and it took a half an hour to find it back on the floor with a magnet whehe)
Now the screen and the button-PCB is ready to take apart from the casing. A bit of the flatcable is glued so be patient.
When you managed to loosen the screen and buttons, place this part at a safe place so it can't be harmed.
Now this is tricky.
Now you have only a front casing with the digitizer.
It's very tight glued so you have to press at the back of the digitizer to loosen it. Be patient, you can break the casing of your device.
Also take care that you do not break the flatcable of the old digitizer because you have to place the cable of the new one at the same way, take a look at the old one when you placed it apart from the casing.
You have to flip the cable like this picture when you placed the new one in the casing.
when you did this, you can replace a little cushion which you had to remove from the flatcable from the old digitizer.
Now replace the screen and button part. replug the 2 flatcables, place the mainboard its place, replug the small flatcable of the digitizer (be sure that the handle is vertical when you do this. When the cable is plugged, place the handle horizontal.
Replace the backcover, the 4 screws, simcard and the memorycard and batterycover.
Press the on button.
Et voila!
As good as new :
The only issue is, that we do not have a dust free environment like HTC has.
The result:
Don't forget to calibrate
All the pictures are clickable.
Sorry for my bad English
And now one more beer and a long sleep
Thanks!
Thank you Marcello! I will give it one more try.
Hi Marcell-o your guide looks solid and the pics look nice...
You are from the Netherlands, where did you get your screen? I am from Belgium, that's why I am asking...
I have two problems with my Jade:
1) My screen is all scratched up, and I need to replace it, so for this only the upper part is needed, right?
2) A few weeks ago when I was in the bathroom and took the phone with me there is since a square "oily" stain in the middle of the screen. I read elsewhere that it's due to the humid enviroment, so I guess I need to replace the LCD part too?
I saw that the screws beneath the backcover are Torx, but what number Torx is it exactly, and is that same Torx used for the screws on the mailboard of the phone?
Thanks in advance for any answers!
Greetz
I bought it here: http://cgi.ebay.de/ws/eBayISAPI.dll?ViewItem&item=260513873708
verry good price!
I'm sorry, i do not know the torx number i was just happy to have the right one.
What you need for the scratched screen is indeed the touchpart(digitizer)
The screws inside(for the buttons/screen) are just the four points(?)(kruisschroef) The mainboard is clicked.
Can you make a picture of the "oil" stain maybe it's also solved with the digitizer replacement.
Hi Guys,
just this morning I've managed to replace a digitizer in my Jade, as it was punctured by some pointy child's teeth . A bit unlucky though, cause I couldn't find this thread before (silly me !) as to get some instructions how to do that.
I'd like to add some tips to Marcell-o's guide:
1. The tools you need are:
TORX T6 screwdriver for 4 outside screws
Philips PH0 (or 00) screwdriver for 2 inside (button panel) screws
Thin Tweezers for replacing flat cables.
Office/Swiss knife for replacing Digitizer itself
2. To prevent any damage to your front cover, I would recommend to 'cut-off' the Digitizer from the inside, before pushing it out. I used a thin Swiss knife for this and started from the top corners, slowly going towards the bottom. This also left all (or most) of the glue at the case side so there was no need to apply additional glueing.
See attached Photo
[Sorry for adding like that, but I'm not allowed to add link as a new user]
3. To make your Jade scratch-proof as well as responding better to your fingers, I'd recommend the Advanced Screen Protector from ProPorta.com. It's nothing close to cheap crap from e-bay as 3 screens for a quid and literally increases touch sensitivity rather than decrease.
Good luck!
Catalan said:
Hi Guys
My name is Luis and I live in Costa Rica. I have a HTC Jade which recently got the LCD screen broken . I really really appreciate if you can name me an Accesories Store located in USA to buy the screen. Since I live in Costa Rica it seems to be the logical place to import. HK is a little bit far from us!
Thank you in advance.
Click to expand...
Click to collapse
would you sell it as is ? Pm me/
zubenelgenubi said:
Hi,
I also have a broken lcd. I ordered a replacement from brando. Is there a service manual or dismantling guide that shows how to replace the LCD?
TIA
Click to expand...
Click to collapse
and would you also ?
Before we were so rudely interrupted in the original thread, we were discussing the G1 hardware keyboard replacements. Please folks, if you must flame each other do it via PMs to avoid locking legitimate threads.
I've been able to find some inexpensive after market replacements on eBay, but still am not sure how difficult it is to actually do that. All the sites I've been able to find on the subject only provide time-lapse dis-assembly instructions of the entire phone. If anyone has done the replacement themselves, I'd greatly appreciate pointers on how to keep my phone operational after I put it back together.
I replaced the white keyboard in my Dream with a black one. It was a scary operation as it takes a bit of force to dismantle. I accidently pulled my antenna off and disconnected a flylead. ment my phone had no signal at all. later when i got home (did it in work ) i took it apart again and fixed it.
Take your time and have patience, alot of it is plastic and clipped together so requires a bit of force.
May I ask what is wrong with the keys on the bronze one? I did a quick skim of the old post and gather that you can't see the keys in daylight but I don't get why?
I'm just genuinely interested, I have a black G1 so never had such a problem.
brummiesteven said:
May I ask what is wrong with the keys on the bronze one? I did a quick skim of the old post and gather that you can't see the keys in daylight but I don't get why?
I'm just genuinely interested, I have a black G1 so never had such a problem.
Click to expand...
Click to collapse
It's the combination of silver keys with light-silver backlight that make the lettering almost impossible to see in day light conditions. I'd take a picture if I had a camera with me today. Whoever came up with that color combination should be fired. Or at least made to stare at it every day for the next year. I have to tilt the keyboard at a weird angle just to distinguish the letters. From what I understand the white G1s suffer from the same problem.
The "Backlight Off" app definitely helps as it lets you toggle the backlight with a keyboard shortcut. I'm looking for a more hardware solution though.
I've been thinking about changing keyboards and housings too. But from what ppl are saying it seems to be pretty exhaustive. Do any of you guys have the service manual? I DL'ed it from somewhere and it goes through each step of disassembly and also shows assembly. I'm sure it would help out to give an idea of what you need. But like I said, even having read the service manual, it's still quite scary.
A full housing from my understanding is a bitc(....doing the KB I can see why. The LCD portions look ridiculously complex in comparison to other phones.
That said if you have the proper tools , good organization or memory , steady hands and patience really shouldnt be "that" tough to do the keyboard.
Heres the thing. Its really not that hard to unscrew things etc...but the piece you need to move in order to get proper access to the KB has 2 ribbons that are a PAIN IN THE ASS to take off and put back properly. Theres so little room for error.If youve never worked with ribbons before BE CAREFUL.
I will say G1 is pretty unique in how its put together , I swear they were determined to make it as complicated as possible
The really pain in the ass part is that the online manual/guide will merely tell you something like "remove part A" but no explanation how. Theres also 2 screws I swear it glossed over leading to frustration when I did the trackball/front keys.
Torx 5 and really good mini screw driver are mandatory.
Nice lil workstation is really helpful..(masking tape ,towel , table lamp or LED headlamp , vitamin/pill cases etc)
Im no mechanical engineer but Ive opened up damn near everything Ive ever owned at some point. Took me a solid 3 hours from start to finish. With major time spent on organizing the screws pieces and those damn ribbons.
I will say the black KB makes a HUGE difference. Black key on the front arent necessary but do look better and add much needed contrast.
KOF33 said:
I will say the black KB makes a HUGE difference. Black key on the front arent necessary but do look better and add much needed contrast.
Click to expand...
Click to collapse
Pics, or it didn't happen
Thanks for the tips!
Chahk said:
Pics, or it didn't happen
Thanks for the tips!
Click to expand...
Click to collapse
As you can see I also replaced the trackball with a glowing white one.
lol at the trackball
doing a case swap is only bad the first time LMAO. I learned a lot, like for example the brass inserts that the screws go into...are not pre-installed. You must CUT Them out of the old housing and HAMMER them into the new oneBut in the end, it turned out very nice.
As far as just replacing the keyboard, it isnt too bad actually once you know what screws hold what down!
-Remove the 6 torx screws for the back housing
-GENTLY pry open the TOP of the casing with a plastic case tool, work your way down to the bottom of the housing. The bottom is a PITA to remove. I usually get it by rocking it gently back and forth
-remove the long and short coax leads from the motherboard side. swing them out of the way
-peel back the tape and GENTLY pull the bottom connector (mouthpiece module) from the motherboard.
-peel back more tape and lift the latch for the keyboard connector (the one on the side)
-Peel the camera module up SLOWLY (it is double side taped down) as well as the imei card. The cam cable is routed under it, lift it all as a unit. When you get to the motherboard, STOP
-Now, gently twist the whole camera and motherboard unit as a whole until it is free of the latch on the side. Gently lift the camera end exposing the 2 small ribbon connectors on the bottom.
-Peel back the tape and GENTLY lift the ribbon connectors out of the board. Place the motherboard/camera unit to the side for now.
-Remove all the black and silver screws for the metal piece. The lcd should stay in place as the mouthpiece plastics kinda hold it for you, but you should still support it to keep from hurting the connections.
-Viola, keyboard access. Remember when you put it back together be sure to re-tape all the connections, else when you drop your phone one of them may pop loose.
Keeping the motherboard and camera/imea plate all as one module saves you from a very difficult connection and will help you keep everything aligned when reassembling it.
I guess the spacebar has 2 functioning buttons, (left and right) ... well my right side just konked on me, and i was wondering if a replacement keyboard off ebay will fix this, or are they just the button "covers"?
the "buttons" are just plastic nubs that make contact on a board behind it. That board would be what you need. I dont know if there are any on eBay, but I have a spare one if you want to PM me for details.
I dropped my G1 about 6 months ago and was devastated. After entirely too much research I finally got the guts to purchase a replacement digitizer and managed to install it successfully. However, in the process I managed to rip the LCD ribbon cable. I then had to order a replacement LCD screen. I've also damaged one of the black ribbon cables pretty severely causing the touchscreen to become unresponsive sporadically. I've just placed an order for one of those ribbon cables and will hopefully have that up and running soon. I've also purchased an entire new housing unit to rebuild the phone to make it look as new.
Now when I first took this thing apart I was by NO MEANS an expert or have ever done something like this before. I'm just an avid enthusiast who wanted to save a little money, feel a sense of accomplishment and to learn a few things along the way. I technically paid nearly the same amount of money it would have cost me to send the unit to HTC for repair, however i've learned everything there is to know about my phone's hardware. I know which board does what and are extremely confident about fixing ANY hardware problem in the future.
If you have the time, patience, and truly want to become confident about the workings of your phone, then I highly recommend fixing it yourself. I've bought my parts for VERY cheap off of reputable ebay buyers. You can find EVERY single piece for your phone on Ebay. My LCD has 1 dead pixel, but I guess that's the risk you take when you buy really cheap parts.
Hope this helps.
Hey guys,
My white unlocked Hero has sustained some nasty body scratches plus it is starting to turn yellow. I'm considering a full body replacement. I was only able to find this:
http://cgi.ebay.com/GENINUE-HOUSING-FACEPLATE-FACIA-GOOGLE-G3-HTC-
HERO-WT_W0QQitemZ280402919652QQcmdZViewItemQQptZPDA_Accessories?hash=item41495100e4
Do you think that it's going to be as good as the original one? The seller claims that it's genuine, What do you think?
I found a site that has both the black and white housing for the gsm hero.
http://www.truesupplier.com/faceplate-housing-cover-for-htc-hero-g2-touch-white-color-pr-18489.html
How do I know that it's genuine? or at least as good as the original HTC cover?
slimfady said:
How do I know that it's genuine?
Click to expand...
Click to collapse
The web page is called "truesupplier.com". OF COURSE its genuine
How hard is it to change the housing anyway?
by changing housing you will probably break phone trust me ... and truesupplier housing is oem not genuine by looks of it..
He might not break it if he's careful, and has the proper tools. I've taken apart a few phones without causing any problems.
So unless i'm handy at doing these things, I should not do it myself?
What if I have our local HTC agent do it? Will it at least look as good as new?
i have the white hero and would love to put the black case on it.
the site mentioned above says it comes with the tools needed to change the cover, has any tried doing this?
i would love to go for it but don't want to f*&k my phone up!
i think its not so difficult to switch the cover if you take off the backcover there are 6 screws than open the case from the top of the mobile phone and pull it off
but becarefull maybe there are flatcables from die lcd or the trackball just make it slow and be carefull all the time
and maybe you can find a dissembly how to in google
peace
this site has pics of disassembly of a hero but it's in russian.
http://www.pdacenter.ru/razborka/htc_hero/
If you have to pry the phone open use something plastic so you dont damage the original case. Just in case the ebay housing is rubbish.
hawwy said:
by changing housing you will probably break phone trust me ... and truesupplier housing is oem not genuine by looks of it..
Click to expand...
Click to collapse
whats the difference between oem and genuine
any1 bought replacement white hoising? mine is getting yellow. so need to buy a back cover.
Thinking of buying one myself. I accidentally dropped mine on the tiled floors of my workplace toilets LOL (luckily not IN the toilet). so now there's a little nick on the top left corner of the case.
If this is your first time you will probably scratch the covers but nothing more. You need to be very patient and i will suggest take a look to a good tutorial.
iopened my hero 1 week ago and its so easy maybe in the next days i will upload a video in youtube
bye
I bought the ebay one. It's surprisingly well built (Not Teflon though).
The sad part is that my touch screen got screwed up during the installation. The bottom part of the screen is no longer functional and the sensitivity is messed up overall. Did the replacement in a local phone shop.
Now trying to find a way to fix it.
gyounut said:
iopened my hero 1 week ago and its so easy maybe in the next days i will upload a video in youtube
bye
Click to expand...
Click to collapse
That would be greatly appreciated!
hmm do you want to sell me your backplate of your old case? i need it please
and to fix your problem : you need a new display glas with digitizer
to remove your old glas: use a hairdryer, you have to heat up the old clue of the old glas and than you can push it easily out of the frame but be carefull not to heatup the frame, the plastic can deform, maybe you can cover it with aluminium foil from the kitchen
the video of the dissembly will be uploaded tomorrow by me
good night guys!
slimfady said:
I bought the ebay one. It's surprisingly well built (Not Teflon though).
The sad part is that my touch screen got screwed up during the installation. The bottom part of the screen is no longer functional and the sensitivity is messed up overall. Did the replacement in a local phone shop.
Now trying to find a way to fix it.
Click to expand...
Click to collapse
Where can I find new display glass for HTC hero? or can I just buy something generic?
I don't mind giving you my old backcover though it's in a very bad shape (which is why I wanted to replace it in the first place).
I can't find any info on this, but it looks like it could be tricky to replace. I cracked my glass by dropping it onto stone, still works OK. You can pick up digitisers pretty cheap on ebay (£20 UK) but does anyone know how to replace? I read that they can be glued to the LCD?
Thanks
Google for the fixit website, if someone has done it there will be a tutorial, or you could follow the guide on here to upgrade your sd card....only because you have to take the phone fully apart. You need to check if the lcd is glued or like the iphone 4 resin. If they are a sealed unit you'd be better off getting the lcd/digitizer combo on ebay. trying to separate an lcd from the digitizer is asking for trouble imho.
I have ordered a digitiser, really hope the digitiser is not glued to the LCD, there is a big price difference. I'll let you know how I get on.
I bought a Mozart with wrecked digitizer and also want to repair it. The digitizer is on its way, so in a week i could tell you how difficult or maybe easy it is.
If you are faster, please post your experience.
I found this thread on xda.cn, and it seems that the lcd isnt glued on the digitizer, so lets hope so
hxxp://xxx.xda.cn/newshow.php?snid=2167
EDIT: sorry cantpost links, so must change the x's to t's and w's
I have got my digitiser now, looks brand new. Just need to find the time to replace, might upgrade the SD card at the same time.
Done
I did this with Andy's guide to help: http://lifeinthefastlaneok.wordpres...-7-mozart-sd-card-memory-upgrade/#comment-225
I used this guide to replace my digitiser (the glass) which I smashed. The good news is that the digitiser is not stuck to the LCD at all. I just bought a grade A digitiser off ebay for £20 which was pretty much perfect - glass was perfect with a couple of small marks on the back case, but basically like new.
There were a couple of differences to this guide:
- Had to replace a speaker type thing at the top of the digitiser that was not present on the new one. Came off quite easily, just stuck in.
- Had to remove the USB port of the old case back (if you are replacing that too) but that was just a couple of screws
- You dont have to split the PCB off if doing this, you just take off the black clips to take it apart and then remove the orange ribbon cable, it is a little tricky to get the new one in but OK.
I now have a phone as good as new, I didn't replace the SD at the same time but probably will do at some point when I can stand loosing all my data.
Found time today to replace the digitizer. I also used Andy's videos for instruction. And it's really not that hard. Pretty easy for someones first mobile phone repair.
Well done, I would add for anyone else needing to do this, be very careful not to touch the inside of the digitiser or the LCD when you have it apart! Also have a glasses cloth handy for removing any dust particles just before you put it back together.
I do have one strange thing however - before I had intermittent issues where I could not slide the screen up when locked for 10 seconds or so. No I have a slightly different issue when unlocking - it doesn't always let me press on the right hand 3 numbers on the PIN screen! So it seems the unlocking issue some people have is due to a hardware issue. My digitiser was second hand so I might ask for a replacement, but I can change my pin so that it is not an issue.
My Mozart touch-screen hardly works at all plus my wife's Mozart has a cracked digitizer glass (still working fine).
So silly me I took the plunge and ordered three cheap replacement digitizers via eBay (from Hong Hong). They arrived today and all are s**t useless.
When I opened the box I smelt the rat when I spied the HTC logo on each was blanked out on the outside of the plastic zip-lock bags (with what looked like black felt pen), plus each glass has minor blemishes/scratches. Comparing each with the digitizers I removed from my and my wife's phones, they have a different design of ribbon cable conductor layout plus there are indications the plastic moulding isn't as well finished in a couple of places. Either these are factory rejects or knock-off copies. Lesson learnt :-(
Anyway, I now need to buy genuine HTC parts.
Any pointers toward reliable sources appreciated, thanks.
KJ
I have bought some off ebay. The problem is that these are almost always from returned Mozart's which may well have been returned due to non responsive screens, which seems to be a very common problem.
I have had 2 off the same chap now, one is OK but not perfect, the other one didnt work at all.
I would just keep returning them until you get one that works.
Sometimes you will find new combined digitiser/LCD's on ebay too, these would be a better bet but cost more.
Can someone who as changed a screen on this phone using Andys guide, please tell me how easy or hard it was, and how long does it take??
And would be grateful if someone could give me a link to the correct digitizer for this phone....
I am in the UK and have been qouted 50 pounds at a phone shop for the to supply and fit screen...
Did you see my post?
There were a couple of differences to this (Andy's) guide:
- Had to replace a speaker type thing at the top of the digitiser that was not present on the new one. Came off quite easily, just stuck in.
- Had to remove the USB port of the old case back (if you are replacing that too) but that was just a couple of screws
- You dont have to split the PCB off if doing this, you just take off the black clips to take it apart and then remove the orange ribbon cable, it is a little tricky to get the new one in but OK.
The most tricky thing for me was getting all the dust off the LCD and the digitsier, as soon as you get it apart things start sticking to it like crazy. Have a clean glasses cloth around.
It takes about an hour on your first go. The main thing is to get the orange ribbon cablle in fully, it can be tricky - you need to get a good grip on it (fold it a little) and push it home quite hard, otherwise you get it all back together and find it doesn't work.
I have had 2 dodgy screens off ebay, £50 sounds OK if it is a brand new original HTC screen.
Or just search for 'htc mozart digitiser' on ebayt there are loads.
hsclater said:
I have bought some off ebay. The problem is that these are almost always from returned Mozart's which may well have been returned due to non responsive screens, which seems to be a very common problem.
I have had 2 off the same chap now, one is OK but not perfect, the other one didnt work at all.
I would just keep returning them until you get one that works.
Sometimes you will find new combined digitiser/LCD's on ebay too, these would be a better bet but cost more.
Click to expand...
Click to collapse
Thank you for that. A close look at the ones I bought from china I'm sure now are removed from phones with faulty digitizers, then repackaged as new. One of the three had significant dust and dirt on the inside of the digitiser screen. I've requested a refund via PalPal disputes.
I've ordered some digitizers from ecell in the UK. I'm led to believe by them that these are genuine HTC factory supplied spares.
KJ
I just replaced my 4th screen (1 broke, 2 dodgy).
This one is perfect - as new condition and works perfectly, my last one was not responsive in some situations e.g. lock screen.
This is the one I got (UK)
http://www.ebay.co.uk/itm/130498971267?ssPageName=STRK:MEWNX:IT&_trksid=p3984.m1497.l2649
Of course, your mileage may vary - some are probably good, some not. Replace it, if it doesn't work ask for another, etc.
My new digitizers arrived today from the uk. Horray they are genuine HTC spare parts properly packaged. The downside is they don't include the frame the glass sit in and is adhered to.
So I watched the official HTC Mozart disassembly video on youtube to see how to remove the existing digitizer glass from the frame - got it apart ok after heating the unit to soften the adhesives but it didn't come away entirely cleanly i.e some of the adhesive foam broke away and was left on the underside of the glass.
So... check on eBay and found sellers selling refurbished screen frames ready for a new glass to be attached.
Will update on progress once they arrive.
KJ
just ordered my digitiser today... wish me luck...lol
poolielad said:
just ordered my digitiser today... wish me luck...lol
Click to expand...
Click to collapse
Well I am now buzzing... have just changed my screen at it works perfect.....
£50 they wanted at the shop...it cost me £13....
Just to let you know how easy this is to do........If I can do it, anyone can..
Did anyone find a reliable supply in the end? I just cracked my digitiser so looking to replace it...
--edit--
Also, how much have others paid? Don't want to be ripped off for some sub-standard part.
Hello everybody,
I m trying to replace the digitiser of a HTC Mozart too.
It is really easy to do, even the part where you have to take off the digitiser from the plastic frame.
But I have an issue, it is the second digitiser I am using ( from the same ebay shop ) and the digitiser is working inverted vertically! Really strange but it is like that.
As the mobile phone is started up, when I push on a left buton, it push on a right button ! On the key board, when I press on "P" it press on "A" ( i m using an Azerty layout, I assume it should be "Q" on your layout ).
It is really anyoing of course.
It is the second screen I received from the Ebay shop and same issue, I don't think the problem come from my side, but I just want to ask to you all if somebody have an idea or the same issue once.
fx.lagwagon said:
Hello everybody,
I m trying to replace the digitiser of a HTC Mozart too.
It is really easy to do, even the part where you have to take off the digitiser from the plastic frame.
But I have an issue, it is the second digitiser I am using ( from the same ebay shop ) and the digitiser is working inverted vertically! Really strange but it is like that.
As the mobile phone is started up, when I push on a left buton, it push on a right button ! On the key board, when I press on "P" it press on "A" ( i m using an Azerty layout, I assume it should be "Q" on your layout ).
It is really anyoing of course.
It is the second screen I received from the Ebay shop and same issue, I don't think the problem come from my side, but I just want to ask to you all if somebody have an idea or the same issue once.
Click to expand...
Click to collapse
Mate, I had the same problem. However it seems no one was able to help me either.
I also purchased a digitizer from Ebay for my Mozart - the exact same inverted issue occurred with me. I wasn't able to find a solution.
I'm in Australia with a T8697 model. The digitizer I received from Ebay had a circle around the windows button at the bottom - This was not on my original screen.
In the end, I purchased a digitizer from an Australian business. Cost double the Ebay digitizer did, so I hope it works... Haven't received it yet, but I'll let you know when I put it in.
What model Mozart do you own?