[Q] Sprint Touch Pro 2 bricked or not?! - Android Q&A, Help & Troubleshooting

Hey guys this is my first post in the forums, and an unfortunate one at that !!
First of all I'd like to say thanks to anyone who can help a sister out , and thanks to all the people who contribute to XDA and it's awesome community.
Here is the issue, I was trying to switch the TP2 from Sprint to T-mobile services, followed directions as said and now the phone will not turn on at all.
However the phone is still being detected in device manager as an unknown device and it says Qualcomm CDMA technologies msm. I have tried installing the driver, with no results.
It will not go into boot loader, and it will not hard reset, I've tried every combination of pushing buttons I can think of, even the small little reset button.
Is this phone bricked?
Or is there a miracle that I can get it to work properly again?
EDIT: The strangest thing is that if the battery, sim, and sdcard are out the phone led will blink for a split second when connected usb to pc or a charger.

Related

Help with my brick... please?

Thanks in advance if anyone can come up with something that helps... I can't imagine what that might be though!
This morning I had a stock Mogul... original ROM, no hacks, even had the Sprint S/W on it. It worked fine.
I downloaded the new Sprint ROM 3.35.651.2 and ran it. While running the Mogul rebooted, went to bootloader, then failed. It was then stuck in bootloader mode. I read up and found that a successful flash should bring it out gracefully so didn't troubleshoot much. I tried a couple of times more to no effect. It was still in bootloader mode.
I then downloaded the old 2.17.651.0 ROM from HTC and that wouldn't work either. Still in boot loader mode.
I read somewhere that a guy got the 3.16.651.0 leaked ROM to update even when the others would not. So, I downloaded and tried it. Everything looked good! It was loading the ROM, the bar went across the screen to 100% and then...
nothing. A black screen. Vista loaded some new drivers and seemed to know there was a USB device attached but I couldn't connect to it in any useful way through Explorer and it didn't show up in the Mobile Device Center.
I thought I'd try flashing it again but since the screen was black I was just guessing. I did a hard reset (both soft keys plus soft reset button) and I got nothing... not even the same connection I'd had after the 3.16 update.
Now, I plug in the device and get no USB connect sound or notification in Windows. I get a orange light on the right LED for maybe 15 seconds then it goes out. Other than that one brief LED the thing is a brick as far as I can tell.
Any ideas? I plan on taking it in to Sprint tomorrow and telling them they bricked my phone with their update if I can't figure anything out tonight.
Thanks!
First POSSIBLY legitimate brick story I've seen.
Have you tried holding down power and camera while pressing reset to see if you can get back to bootloader?
Geckotek said:
First POSSIBLY legitimate brick story I've seen.
Have you tried holding down power and camera while pressing reset to see if you can get back to bootloader?
Click to expand...
Click to collapse
Yes.
FYI... I just left the battery out for about 5 minutes (what the heck, worth a try right?) and put it back in. I get no lights, buttons do nothing, soft & hard reset do nothing, forced bootloader does nothing. The only way I can get the phone to do anything is to plug it in to a USB cable. The orange light comes on for about 15 seconds then goes out. The computer never recognized there is a new USB device attached.
I loaded many custom ROMs on my old 6700 and never had a problem. I leave my new 6800 alone and wait for the upgraded stock ROM and look what happens! Guess I shoulda used a custom ROM instead, eh?
lol sounds like a legitimate "brick" to me. Very strange, and congrats on your new mogul paperweight (i also have one that was a victim of water) haha, good for holding things down on the windy days.
Yup, bricked.
Sprint couldn't figure out how to unbrick it and just gave me a new phone. The new one upgraded nicely and now I have GPS!
Everyone enjoy the upgrade!
same problem
no need to retype what you said. i had the EXACT same problem. phone was completely bricked and continued to crash at 11%. I went to my local store (i work for sprint, and i know a smart tech there) and was told it was kaput. Hard reset, tried to reload other roms, the whole 9 yards. It's a goner, and now i have a new mogul in my hand. I'm afraid to try it again. I'm running vista, and im wondering if that's the problem.
Anyone with vista have the same bricking problem? Is it an issue to directly upgrade from factory rom to the 3.35? My old brick had the current 2.17 or whatever... HALP
Vista
The first time I tried the update I connected the Mogul to my Vista Business 64bit Thinkpad T61p.
The second time I tried it (on the new Mogul) was from my Vista Business 32bit desktop (white box).
I don't know if that helps or not. The second time went smoothly.
On another note... an entertaining one... while I was in the Sprint store today waiting for their tech to confirm that the phone was bricked another guy came in with a Mogul and complained of the same thing. I took the last Mogul they had in stock. Poor guy. I hope they get more soon... there are a lot of people who want GPS and are upgrading their phones. That means there are gonna be some more bricks I'd think.
Hey guys Im a noob and im having a bit of problems
Im stuck in the bootloader screen
TITA100 MFG
SPL-2.40 Olipro
CPLD-9
My comp has windows vista premium so instead of activesync i have windows device center 6.1 I have unclicked allow USB connections
but i think my comp doesnt recognize that they the phone is connected at all although i do here the sound that lets me know that a usb device is connected
exitbl.exe doesn't work keeps telling me
cannot open USB port
Please make sure that USB connection in Activesync is disabled
Also make sure that your USB cable is properly connected
if it helps im on a bell phone

HTC HD2, not responding to touch

Hello,
not sure if this was posted before, but i have came across an issue with my htc hd2, after installing the new rom on my device, it refuse to respond on any touch. the only features to work on the device are the hard buttons. i have rebooted the device, removed the battery but cannot do anything on the screen, i cannot slide to unlock or answer calls using the touch.
urgent help needed.
thanks
if its an issue as serious as that, try a different rom/radio combination!
sounds like you might need to send it to HTC Care!
meanwhile, use something like pocket controller to control your device from your pc. you could also try and install spb pocket plus and restart in safe mode?!
Best of luck!
I did try different radio, but its not updating, i had 2.05 and i tried installing 2.07 no changes, i tried different rom still no difference....i did sent in my phone to htc care, but they replied back stating the boot driver is not loading up for the device and they would have to replace the mainboard for the amount of $400. any best suggestions.
im sure the device isnt bricked, its detectable by my computer, i can power it up and answer my calls...

SGS2 bricked while booting up.

Well, first of all, I should start by greeting the community, as this is my first post. So, yeah, hey everybody, been reading the forum for quite a while now, and it's been of a great help
Now, to the problem - this morning I noticed that my sgs2 had turned itself off. I didn't suspect the phone to be bricked or something as this happens from time to time when using custom roms. I tried turning it back on, it booted up, showed my kernels logo (DorimanX, not sure for the version though), so I put my phone in my pocket. After half an hour or so, I wanted to make a call, but I noticed that my sgs2 still hadn't booted up. So I tried restarting my phone using the power button, but instead of restarting it just turned off and I hadn't been able to turn it on since - it's bricked
I've heard of phones getting bricked while flashing a new rom or kernel, but never had I thought it could happen on simply booting up...
I did some research on bricked SGS2 and here's what I have done so far:
I've tried booting up in recovery/download modes, but that doesnt work.
I've tried soft/hard resetting my phone - still no luck.
I've also tried making an USB Jig, didn't work though. I'm not quite sure if my self-made jig works in the first place, as I did mess up the micro usb connector pretty bad while soldering resistors to pins. I'll try that one again with a different jack later and will keep you updated on weather it worked or not.
So, my question is, if my second try at making a USB Jig fails, is JTagging my only chance on reviving the phone? I guess that a MOBO change would probably help.
Another question is, if JTagging is my only chance, wouldn't it be easyer to just replace the bricked NAND chip? Then again, even though I have all kinds of soldering equipment accessible and also have the skills to do it, I have no idea where it's located on the mobo... Some info on that would also be much appreciated.
I havent flashed a new rom for quite a while now, last time I did it was when the latest version of Resurrection Remix was released.
My CPU wasn't overclocked - it was underclocked to 1GHz.
I was using DorimanX kernel.
Thanks in advance
jankanolv said:
Well, first of all, I should start by greeting the community, as this is my first post. So, yeah, hey everybody, been reading the forum for quite a while now, and it's been of a great help
Now, to the problem - this morning I noticed that my sgs2 had turned itself off. I didn't suspect the phone to be bricked or something as this happens from time to time when using custom roms. I tried turning it back on, it booted up, showed my kernels logo (DorimanX, not sure for the version though), so I put my phone in my pocket. After half an hour or so, I wanted to make a call, but I noticed that my sgs2 still hadn't booted up. So I tried restarting my phone using the power button, but instead of restarting it just turned off and I hadn't been able to turn it on since - it's bricked
I've heard of phones getting bricked while flashing a new rom or kernel, but never had I thought it could happen on simply booting up...
I did some research on bricked SGS2 and here's what I have done so far:
I've tried booting up in recovery/download modes, but that doesnt work.
I've tried soft/hard resetting my phone - still no luck.
I've also tried making an USB Jig, didn't work though. I'm not quite sure if my self-made jig works in the first place, as I did mess up the micro usb connector pretty bad while soldering resistors to pins. I'll try that one again with a different jack later and will keep you updated on weather it worked or not.
So, my question is, if my second try at making a USB Jig fails, is JTagging my only chance on reviving the phone? I guess that a MOBO change would probably help.
Another question is, if JTagging is my only chance, wouldn't it be easyer to just replace the bricked NAND chip? Then again, even though I have all kinds of soldering equipment accessible and also have the skills to do it, I have no idea where it's located on the mobo... Some info on that would also be much appreciated.
I havent flashed a new rom for quite a while now, last time I did it was when the latest version of Resurrection Remix was released.
My CPU wasn't overclocked - it was underclocked to 1GHz.
I was using DorimanX kernel.
Thanks in advance
Click to expand...
Click to collapse
What happens when you plug the charger. Does it charge?
pasanjay said:
What happens when you plug the charger. Does it charge?
Click to expand...
Click to collapse
I guess the battery is charging, as it heats up, but I don't see the charging animation. Also my PC won't see that a USB divice of any kind is connected.
jankanolv said:
I guess the battery is charging, as it heats up, but I don't see the charging animation. Also my PC won't see that a USB divice of any kind is connected.
Click to expand...
Click to collapse
order an usb jig and try. If it does not work send it to a repair center
Very similar happened to me a couple of days ago. Sgs2 crashed and wouldn't boot. I was also running dorimanx kernel, under clocked at 1ghz.
Originally I managed to get to download mode (not recovery mode). Kernels wouldn't flash via odin. I also tried using samsung kies to flash stock without success.
I tried the solution for nand bricked phones in this forum, however, this appears to have hard bricked the phone, since it failed to flash and now the phone does nothing (other than get hot when it is plugged in.) Nothing shows on screen. The PC does not recognise the device.
None of the threads I've read seem to offer a solution to this - any ideas? I guess I need to try a service centre, but thought I'd mention since I had same configuration as jankanolv, which of course may just be a coincidence...
birdr said:
Very similar happened to me a couple of days ago. Sgs2 crashed and wouldn't boot. I was also running dorimanx kernel, under clocked at 1ghz.
Originally I managed to get to download mode (not recovery mode). Kernels wouldn't flash via odin. I also tried using samsung kies to flash stock without success.
I tried the solution for nand bricked phones in this forum, however, this appears to have hard bricked the phone, since it failed to flash and now the phone does nothing (other than get hot when it is plugged in.) Nothing shows on screen. The PC does not recognise the device.
None of the threads I've read seem to offer a solution to this - any ideas? I guess I need to try a service centre, but thought I'd mention since I had same configuration as jankanolv, which of course may just be a coincidence...
Click to expand...
Click to collapse
Sounds familliar, lol. Anyways, did you use USB Jig to get to download mode? Or you just managed to boot it up on it's own?
I am really confused right now, because I'm pretty sure this can't be a hard brick as nothing has went wrong while flashing something on the device - it just bricked itself...
I've just get in the forum a few minutes ago only to find somoene with this symptoms, and i wasn't in here for too long and voilá...
Since yesterday my SGII, with no problems to this date, went in reboot mode for a few times.
I have no clue what is going on, but im sure something is.
i'll wait to see if theres anyone else complaining about it.
cheers
Hmm... Looks like a lot of people are getting this "brick" lately.
Maybe we all used some kind of app that bricked the phone on bootup?
Well, I tried to make another Jig, didn't work... This time though, I screwed my resitors up...
Another thing - is it really relevant to have exactly 301kOhm resistance between pins 4 and 5? As far as I know, it just kind of short circuits some pins on MOBO, which tells the phone to boot up in download mode. But I might be wrong...
Btw, sorry for the double post.
Same Problem
Hi,
I just face the same problem today,
now my S2 not working and just heat up.
this only happened after the original update done to my S2 - Android 4.1.2 - 2 days ago.
any help please
heat up....near the rear camera heat up?
Sent from the little guy
Mine gets hot near the camera. Nothing shows on screen.
In answer to jankanolv's questions:
- originally I could get to download mode via pressing home/power/volume down. (Not any more following failed flash). I've not tried a USB jig.
- my crash which started the situation occurred while I was listening to tune in radio pro app.
Well guys....near camera heating + no boot/dl/recovery = claim warranty saying that you factory reset the phone, 4.0.4 was laggy.
Sent from the little guy
was going to post a thread asking for help for what appears to be a similar problem
mine got stuck in a bootloop after pulling the battery, tried flashing new software in recovery then tried through odin but kept failing, now its bricked.
does nothing, wont go into either download or recovery mode so looks like its off to the service centre with it.
ahmadmetwally said:
Hi,
I just face the same problem today,
now my S2 not working and just heat up.
this only happened after the original update done to my S2 - Android 4.1.2 - 2 days ago.
any help please
Click to expand...
Click to collapse
Yessss! good to know I'm not the only one facing this issue.
I posted a thread about this yesterday but it is all the way down in page 3 already:
http://forum.xda-developers.com/showthread.php?t=2192996
I tapped on the "sync" toggle on the notification shade and my phone just turned itself off.
Recovery and download mode were accessible though.
Thanks for the help.
I went to Samsung to get them to fix based on the factory reset while on stock 4.04 premise, but they were having none of it, and wanted to charge me to investigate the problem. Once out of warranty period, it seems it doesn't matter if their software can brick your phone!
I found a local phone fixing service in Hong Kong which investigated, diagnosed as a motherboard failure (which I suspect my problem genuinely was given how firmware flashes were failing), and replaced + fitted for 700hkd, (approx 90usd). The guy did it in front of me within 10 mins. "Andy Telecom" in Mongkok, on +852 9237 9237 in case someone else has the same issue locally.
Well, outta warranty...that's another story. You only get 1-2 years to brick your device
Glad you had it fixed for 90 bucks, some service centers charge around 150.
Sent from the little guy
Well, I finally managed to make a working USB Jig, tried it on Galaxy Ace, worked like a charm.
What confuses me right now, is that my sgs2 has drained all the battery, even though it was switched off for about 2 days. I'm charging the device right now, and I will keep you updated on weather my jig works..
Sorry for double-posting again on an old thread, just wanted to let you guys know - I took the phone to warranty service and they changed the mobo. I didn't have to pay anything and everything is working normally. Of course all data on sd card is now lost for good, lol.
So if you hard brick your device so badly it even won't respond to usb jig and you still have your warranty active, don't bother trying to revive your phone - just take it to warranty service
I guess they couldn't see the odin download count so they cant void my warranty, he he he ]

Hard bricked Alcatel star

Hi, first sorry for my bad english. As you can read from the title my Alcatel One Touch Star is hard bricked.That happened when i was uploading mp3s from the PC to the phone and I just took the usb out from the pc.Then the phone started reacts very strange so i decided to restart it but it turned off by different way and didn't turn on again. I'm not coming straight up there. I have tried many things from the google and other threads here but my phone don't show any sign of life. I tried all methods of clicking buttons for going into recovery/download mode( i don't know how it is called exactly ) but nothing works. I tried pluging it into PC but it doesn't show up. That is why i think is hard bricked. I have given the phone to a man who fix phones and he told me that the phone is dead .I have heard that this is the best android forum so that is why i'm looking for help here. Sorry if the thread is in the wrong section.
Bump

UMI Iron (BRICKED)

Hi Guys,
Hoping someone can help me - I've searched the forum and can't find a similar thread. Essentially, after months of trying to get a refund on this crap phone, I give in - the issues with this phone are longer than my ****.
Long story short, I installed this ROM using TWRP: http://www.needrom.com/download/umi_iron/#comment-269759
However, after reboot, the phone now literally boots up for a second and resets - I cannot get into Recovery and no matter if I hold power the button and volume, it will not respond. I have SP Flash Tool, but when I connect the phone to my PC, the PC recognises it for a second and then the phone reboots and loops.
To be honest, I've never used SP-Flash Tool and when I power up USBDeview here is what I'm presented with.
http://i.imgur.com/GgS8toq.png
The only thing that happens is when I get the USB connected Windows sound, MT65xxx preloader goes from connected YES to connected NO.
If anyone has any ideas or can give me a bit of guidance, I will bloody well buy you a pint if you are ever in Liverpool, UK.
Oh and the UMI forum is beyond idiotic - I can't even login and when I do, I can't post - I can't verify and it is just a mess.
Let's just say, I will never buy from this company again as all I have with this phone is issue after issue after issue after issue.

Categories

Resources