i have just tried to load the new rom of MiChY. At 88% th pda stop updating and now i have black and white lines to the screen, even i done a hard reset. the pc shows me the mesange "260 error". (so i can' t use ActiveSync). propably i done something wrong
please help
Sorry for my english!!!
i have the same issue only i got to 92% of the rom before it kicked out and left me with the corrupted romm image i can kick off an udate but because the rom is screwed the updater is not getting a valid device id back and i get kicked out at 1% with invalid device id.
anyone with any help or advice would be appreciated
cheers
my apologies for asking a question that seems to have been asked before ifn a different thread, somehow missed those threads when i was looking through the forum the first couple of times.
anyway followed the advice on this thread http://forum.xda-developers.com/showthread.php?t=387454&highlight=mtty&page=4 and then flashed a fresh rom straight onto the device,
so thanks to everyone who contributed to those threads that the soloution was in
it s all ok now
I just got my fuze today and am trying to flash HardSPL onto it. I have followed the instrustions in these threads very closely but everytime I get to the part where the status bar appears on my comp and the phones screen goes black, it doesn't even get past 0% and then on my comp the hardspl RUU program goes to and error page that says Error [260] and the connection fails or something.
I noticed that right before it does that, the comp seems to disconnect activesync from the phone.
Can anyone help, asap!!!!
Thanks.
Please post your question in the dedicated HardSPL thread (about 5 posts above this)....Here:http://forum.xda-developers.com/showthread.php?t=410150
I'll close this thread so you can post in the correct one
EDIT: Ive also removed the cross-post in the other incorrect thread. Please try to use the threads already provided before posting elsewhere.
Hello, my HD2 started entering the re-boot loop probably because of overheating (I live in a warm country and it started showing problems during the summer). After that, I installed the new official rom from the HTC website (finding a SN online :S) after trying to install the new rom I realised I shouldn't have tried that since it wasn't made for my SN. Anw after that the phone is kind of dead, freezes at the HTC boot screen. I have installed HSPL 1.42 on it but I can't load any new rom (I enter the bootloader - that's the only way I can think of since I got lost in a zillion posts) When it starts loading the new roms into the phone I get a 276 error saying it can't finished the procedure. (after such an error on the startup screen I still see the HTC logo but this time with black and white stripes covering the screen). I can't seem to find something similar in the other posts, I hope it wasn't answered somewhere previously. Even if so please redirect me or tell me what else to try since I'm quite frustrated!.. Please explain thoroughly because it's been a while since I was into hd2 tech stuff. Thank you in advance!
PS: Can I somehow find what rom I currently have IF there is one installed? I'm lost here....
t45o5 said:
Hello, my HD2 started entering the re-boot loop ...........................Anw after that the phone is kind of dead, freezes at the HTC boot screen. ................I can't load any new rom (I enter the bootloader - that's the only way I can think of since I got lost in a zillion posts) When it starts loading the new roms into the phone I get a 276 error saying it can't finished the procedure. .
Click to expand...
Click to collapse
check the battery pins. ive read of people for whom it is possible to get into bootloader, and it seems like normal, but then it fails to load when trying to boot fully, usually a reboot loop.
forget about finding what rom is on there currently, its time wasted, really.
a better use of your time is using your serial to find out which rom the htc website will let you have, and flash that, from sd card preferably.
Why not just reset the phone, and start over?
found a good rom, installed it via sd card, still reboot loop. that make me think that the problem might be the battery pins. if so what's the solution?
same thing happend to me just adjust the pins
Foxanax said:
same thing happend to me just adjust the pins
Click to expand...
Click to collapse
how do you adjust the pins? They're supposed to be straight right?
t45o5 said:
Hello, my HD2 started entering the re-boot loop probably because of overheating (I live in a warm country and it started showing problems during the summer). After that, I installed the new official rom from the HTC website (finding a SN online :S) after trying to install the new rom I realised I shouldn't have tried that since it wasn't made for my SN. Anw after that the phone is kind of dead, freezes at the HTC boot screen. I have installed HSPL 1.42 on it but I can't load any new rom (I enter the bootloader - that's the only way I can think of since I got lost in a zillion posts) When it starts loading the new roms into the phone I get a 276 error saying it can't finished the procedure. (after such an error on the startup screen I still see the HTC logo but this time with black and white stripes covering the screen). I can't seem to find something similar in the other posts, I hope it wasn't answered somewhere previously. Even if so please redirect me or tell me what else to try since I'm quite frustrated!.. Please explain thoroughly because it's been a while since I was into hd2 tech stuff. Thank you in advance!
PS: Can I somehow find what rom I currently have IF there is one installed? I'm lost here....
Click to expand...
Click to collapse
Hi,
Did you find any solution for that problem?
Thnx
Okay so here's my story...
I got a little ancy, and without reading ( i know first issue) proceeded to root my phone ( successful ) and put clockworkmod ( succcessful )
However, i decided after to put voodoo lag fix for 2.1 on by just putting on sdcard ( not the actual SD CARD but the internal ) then flashing it.
It hung at the galaxy S i9000 screen for over 20+ min and would not move
I pulled the battery and had a hell of a time figuring out if i bricked it or not...
well i found the odin trick and got it to boot up to the S logo screen.
After that it stays there then the screen goes black and wont boot to android.... now i have no clue HOW to reset my phone.
I've gone into recovery mode and tried to install from zip with update, and it says "no update.zip found" or whatever, and i WOULD put one on , but i can't get into android to do so....
I"m stuck please how do i get back to android!?
Thanks in advance!
Odin again it may take a few tries..ill be watching this thread if you need more assistance
Sent from my SGH-T959 using XDA App
fixed... i followed a couple of threads.. flashed a euro one, then reflashed a us one... and it worked
I did the OTA for .14 where upon my Prime immediately started an infinite bootloop. I tried re installing .14 with the manual sd card method, but it changed nothing. I'd like to try again with .15 but ASUS hasn't updated their page with .15, nor have they responded to my help request within 48 business hours. Does anyone have a link for .15 I can try? Or .11 for that matter so I can downgrade?
Edit: Just realized I posted to the wrong section. I am dumb. Sorry Mods! Go ahead and move it.
If your unlocked then Here you go.
I saw that. I'm not and don't plan to. 8\
Thanks though
I have the exact same problem, and seems like ASUS is not really worried about us ... what are they waiting to finally put online the complete firmware, it's been 4 days since the last OTA ...
Still no firmware and still no response on my support request. Time to take it to Twitter I guess. Got me help when my ISP was trying to screw me.
TheMan876 said:
Still no firmware and still no response on my support request. Time to take it to Twitter I guess. Got me help when my ISP was trying to screw me.
Click to expand...
Click to collapse
It's been over a week that my device is a deluxe paperweight, they're really starting to piss me off ...
Finally !!
http://dlcdnet.asus.com/pub/ASUS/EeePAD/TF201/WW_epaduser9_4_2_15UpdateLauncher.zip
Did it work for you? I'm downloading it now
anthonyalberto said:
Finally !!
http://dlcdnet.asus.com/pub/ASUS/EeePAD/TF201/WW_epaduser9_4_2_15UpdateLauncher.zip
Click to expand...
Click to collapse
I downloaded the US version. How do you install it? it's just a zip file with no instructions or executables. There is no instructions listed on the support site either. Thanks.
Finally, my prime is back to life!
Method known as the EP201_SDUPDATE.zip method :
Download the firmware or your choice on the asus download page. It has to be the same version or an upgrade of your current version. You can't downgrade using this method.
Once downloaded, extract the zip. Inside, there's another file file.
Rename this one into EP201_SDUPDATE.zip and put it in the root of a microSD card.
Put the microSD card into the tf201.
As soon as your device boots (or reboots), hold the Volume Down key until some text shows up on the top left of the screen. Then, press Volume Up once within 5 seconds.
Some more text will be displayed. Wait a bit and ... there's three scenario here :
A) A droid with a blue diamond and a progress bar is showed on the screen for a while, then the device reboots and a long progress bar is upgrading or changing firmware zone. You Win.
B) The device reboots like nothing happened. It means you have a very bad reboot problem. I had it myself using .14. The device reboots so frequently that there's not enough time for it to load the rescue upgrade program. Solution : try again, repeat the steps to enter rescue mode. Eventually, you'll get it (took me 15 tries or so to get it)
C) You see the same thing as A) but then there's a dead droid with a red "!" symbol. It means your microSD card is not inside or the file you've put at the root of it is not valid (no downgrade!!)
So using this method, I was able to upgrade to .15 and my prime is back to life right, syncing all the programs right now, that's great
Yeah, I used that method too. Unfortunatly while trying to fix it the other day I wiped it. 8(
It's running, but now I have another problem. I have no wifi. >_<
Yep, that did the trick. Thanks!
Hello! I have scenario you don't have on your list. My TF201 just keeps repeating the ASUS screen over and over and when I try to go into recovery all I get is the GREEN Android with and GREEN Triangle and Exclamation mark. Have you heard of anyone with this type of symptom?
JuNyA8971 said:
Hello! I have scenario you don't have on your list. My TF201 just keeps repeating the ASUS screen over and over and when I try to go into recovery all I get is the GREEN Android with and GREEN Triangle and Exclamation mark. Have you heard of anyone with this type of symptom?
Click to expand...
Click to collapse
Have you put the right file at the root of your microSD? It's the zip file that is in the zip file you downloaded from ASUS.
Must be renamed EP201_SDUPDATE.zip
And you can't downgrade using this method. Use a different SKU or an upgrade.
It's supposed to work if done properly, give me more details on what you're trying to do (version and sku of firmware you have on tf201 and sku and version of firmware you're trying to use)
anthonyalberto said:
Have you put the right file at the root of your microSD? It's the zip file that is in the zip file you downloaded from ASUS.
Must be renamed EP201_SDUPDATE.zip
And you can't downgrade using this method. Use a different SKU or an upgrade.
It's supposed to work if done properly, give me more details on what you're trying to do (version and sku of firmware you have on tf201 and sku and version of firmware you're trying to use)
Click to expand...
Click to collapse
Thank you for your reply. Here is what I did:
My TF201 is a JP version and originally had HC on it. I read through XDA to find that I am able to use the ICS update from a different SKU so I updated to ICS US Version and all was great except that I could not use my Keyboard Dock since it a JP version Keyboard. Then I noticed we were able to put CWM on the TF201 so I went ahead and did that (I think this may be the reason why I can`t revive my prime.). I wanted to go back to HC so that I can use my Keyboard Dock again (I had already backed my Blob from the time it was still on HC JP Version). I googled the HC US Version and did the downgrade as posted on this site, all went well as it was showing the progress bar of the downgrade. But when I rebooted all I got was the ASUS Logo loop and when I try to access recovery I would see the Android Robot and a progress bar at the bottom then it would suddenly give me the green exclamation mark. I asked around here and was shown your thread so I gave it try using the latest ICS update for US version since that was the SKU of the HC I tried to downgrade to. I followed the instructions on this thread and to no avail will my Prime revive. I have tried about 10 times over and over but would still get the same Android Robot with Exclamation mark. Shall I keep trying your method or is there a possibility my Prime is bricked for good. Any assistance would be great and I am willing to try anything to get my Prime revived again, don`t want to go out buy a new one if I can revive my Prime.
Hmmm that's weird, maybe its because you unlocked your bootloader ... maybe ask to people who also did unlockthe bootloader ...
anthonyalberto said:
Hmmm that's weird, maybe its because you unlocked your bootloader ... maybe ask to people who also did unlockthe bootloader ...
Click to expand...
Click to collapse
Yes it is very wierd. I get no errors like most people do. I think it is the bootloader that is causing the problem. I am going to try to run ADB logcat to see if anything pops out. If I can only pin point the problem I may be able to figure it out or .... not. I am going to ask around some more and keep trying your method. Thanks for trying to help me out! Greatly appreciated!!!
EDIT: I have tried everything to revive my Prime, I pretty much give up. I have asked ASUS for assistance in getting it repaired but have no reply from them yet.
I had a similar issue (stuck at the Eee Pad screen) and used this method to resolve it.
It is worth noting that the Micro SD Card must be formatted as FAT32, not FAT as suggested on some sites. I wasted a day or more on this using a FAT formatted card.