Related
I think my Mogul is bricked after trying the ROM update; after about 7% update Vista kicked off the USB connection and I'm left with a tri-color screen. When I try to reinstall the ROM I get an Error 328 message - Invalid Command. Any help? Thanks!
Definitely not bricked if you can get to the tricolor screen.. which rom exactly were you flashing and what have you flashed so far (unlocker, etc)?
Have you tried updating from the microsd card? That solved a similar problem for me.
AFH said:
I think my Mogul is bricked after trying the ROM update; after about 7% update Vista kicked off the USB connection and I'm left with a tri-color screen. When I try to reinstall the ROM I get an Error 328 message - Invalid Command. Any help? Thanks!
Click to expand...
Click to collapse
What steps have you taken so far? That might help others figure out your problem(I would help but I'm leaving my computer right now)
Just tried to re-cradle and reinstall the update - ROM 3.35.651.2 from HTC's website, and I get the message Invalid Command and it stops the update. Can I run this from the MicroSD card as suggested? Any help very much appreciated!
I have no access to anything on the phone BTW - just the screen and nothing else. The screen has four horizontal stripes - Red, Green, Blue and White. In the red stripe it says TITA100 MFG, SPL-2.03.1000, CPLD-9, and at the top of the screen RUUNBH....
Run Olipros 2.40 bootloader. Than, go back and flash the 3.35. I'm pretty sure you need the 2.40 to load the new ROMs. Yes, just run Olipro's 2.40 while you are in the tri-color screen. Also, make sure you have more than 50% battery life left.
Where do I get the bootloader and how do I run it? Sorry to sound dense, but this is new to me. I have the concept of running the bootload mode - Camera, Power, Reset, so I assume some software needs to be loaded on the MicroSD card? Thanks!
You know, it's fine if you're new to this....everyone starts somewhere...and it's good to see new faces in the community...
But what I don't get is why people insist on just flashing right away without reading and researching. Then they make posts about thinking their phone is bricked, not even knowing what a bootloader is.
My advice before you do anything else is to take an hour and read. Read about how to flash, read about bootloaders, read everything you can find about updating your phone. Then, try and fix your bootloader.
Your phone isn't bricked. A brick is just that, a brick. NOTHING works, not the bootloader, not the buttons, nothing.
gcincotta said:
You know, it's fine if you're new to this....everyone starts somewhere...and it's good to see new faces in the community...
But what I don't get is why people insist on just flashing right away without reading and researching. Then they make posts about thinking their phone is bricked, not even knowing what a bootloader is.
My advice before you do anything else is to take an hour and read. Read about how to flash, read about bootloaders, read everything you can find about updating your phone. Then, try and fix your bootloader.
Your phone isn't bricked. A brick is just that, a brick. NOTHING works, not the bootloader, not the buttons, nothing.
Click to expand...
Click to collapse
i second this emotion
Actually, although I'm new to this forum I'm not new to computers. I'm not as familiar with the inner workings of a handheld. I assume a bootloader is the software necessary to run the ROM flash from the SD card; when I run in bootloader mode, I do get a very brief "image not found", so I assume it's looking for the ROM image on the card. And I'm tracking down Olipros stuff right now through the forums, as well as the recommended reading. With a little written direction I think I can "unbrick" this phone. I did successfully flash another Mogul from a different computer, so assumed it would be as smooth; guess not. For those with the expertise, I certainly appreciate the advice and patience to teach a novice...
Once you find the required bootloader program, just run it as if you are flashing a ROM. Once you get "Olipro 2.40" on your tri-color screen, you'll know that your getting somewhere. But yes search and search and read. I also downloaded everything I think I would need also, just in case.
OK - so far 've tried running the Olipro Bootloader 2.40, but I get "device not connected." Perhaps I should mention I'm running Vista Home Premium, so no ActiveSynch; my PC has Mobile Device Center. I hear the little chime when I connect the Mogul, but the Olipro software doesn't recognize a connection....
I have done all of my flashes on my Vista Home Premium laptop. Make sure you uncheck "allow USB connection" on WMDC. Also, after every failed attempt, take the battery out of your phone for 3 seconds and then reinstall.
Did you mean check "allow USB connections"? WMDC is attempting to connect, but always fails. I was assuming because it doesn't recognize the PDA...
no he meant uncheck....READ!!
start here http://forum.ppcgeeks.com/showthread.php?t=9927
Thanks; I have an XP machine I'll try; jacking with the WMDC drivers in Vista would take more time than its worth...
Actually Vista should automatically find and install the required drivers for you. It shouldn't take long. It's well worth the time considering what you are getting yourself into.
First, thanks for the assistance all. Status to date: I have connected to my XP machine and still can't connect the Mogul to ActiveSynch. ActiveSynch won't recognize the device in its current state. I've tried running the bootloader program both with the "USB Connection" option in ActiveSynch on and off; when I run the bootloader I get a popup window that says "No device connected", and a query "Would you like to try copying again?" with button options "Yes", "No" or "Cancel." Clicking "Yes" gives me the same popup. Clicking "No" lets the loader proceed, but has no effect on the Mogul except ultimately it brings up a screen showing the percentage complete which remains at 0, and on the PC it brings up the Recovery screens for the ROM update, which have no effect on the Mogul because I assume no connection has been made. I'm obviously misinterpreting some of the steps?
Any way to run the loader from the MicroSD card? I think someone mentioned it before?
Sounds like you still didnt get Olipro 2.40 into your machine, right?
When you boot it (press camera+power+soft reset) which bootloader do you get showing?
If its 1.06 or something like that you need to flash a (manufacturer) stock rom.
If its 1.20 Olipro then you need to flash a customized pre-3.16 rom. (if you need one pm me and I will give you a link to a clean one for your carrier)
Either way you need to get the rom file called xxxx.nbh. Rename it to TITAIMG.nbh. Place that file into the root of a FAT32 formatted sd card. Inster it into your sd card slot and power down and power up the titan. It will automagically read the rom from the card and flash it for you. Same goes for radio nbh files
Hi guys need help if possible I read the guide first I FLASH HARDSPL then I used a custom rom ChuckyROM everything updated fine. I power on ChuckyROM is loaded on screen takes like no lie like 10 mins to boot up getting errors I can't get windows mobile device to open usb is plug to computer anything I can do ? Thanks for your time.
otakuk said:
Hi guys need help if possible I read the guide first I FLASH HARDSPL then I used a custom rom ChuckyROM everything updated fine. I power on ChuckyROM is loaded on screen takes like no lie like 10 mins to boot up getting errors I can't get windows mobile device to open usb is plug to computer anything I can do ? Thanks for your time.
Click to expand...
Click to collapse
Run Task29, then reflash the ROM again, but make sure to download it again since it might be corrupted.
Thanks gaarry that help got it working now really appreciate your help thanks again.
I got a friends hd2 several days ago and it was stuck on the White splash screen and wouldn't go further.
I tried Hard reset with keys and it didn't helped to get past that screen.
So i decided to flash a new ROM.
First I installed 1.42.HSPL on it to make myself safe and tried to install WWE version but failed at 9 %.
After this i tried near all the steps from another thread on the forum, the one of italian guy who tried almost everything.
Strange thing is that after trying several roms and failing all the times at 9 %, the phone once booted into windows, and i got this information from it:
Radio 2.05.51.05_2
G 15.28.50.07U
Rom 1.48.406.1 (71294) FRE
But after powering it off it didn't boot up another time.
Also there was a small damage on one of the battery pins but I think i managed to get it soldered from outside with soldering iron.
I also tried with MTTY and it didn't work either.
I got the official rom 1.48.406.1 FRE (because this phone is from swiss operator in french language) but it doesn't flash it goes to 9 % and gives error 290.
Ok, i started the thread because I actually wante to ask the question, why i'm unable to get into the Flash process from SD Card.
I formatted SD and copied the LEOIMG.nbh from official ROM and other ROM's too but when i press Reset and hold volume Down key sometimes nothing happens screen is black, sometimes im going into Bootloader with Serial shown and this text:
"Upgrade ROM code error. Please try again" and in the top right corner its written RUUNBH.
Anyone has any idea what could be problem of this device?
Btw I own LEO too and i never faced any problem till now, it was originally in German Language and i flashed it to WWE and didn't get any problems like this one.
gjizaqin said:
I got a friends hd2 several days ago and it was stuck on the White splash screen and wouldn't go further.
I tried Hard reset with keys and it didn't helped to get past that screen.
So i decided to flash a new ROM.
First I installed 1.42.HSPL on it to make myself safe and tried to install WWE version but failed at 9 %.
After this i tried near all the steps from another thread on the forum, the one of italian guy who tried almost everything.
Strange thing is that after trying several roms and failing all the times at 9 %, the phone once booted into windows, and i got this information from it:
Radio 2.05.51.05_2
G 15.28.50.07U
Rom 1.48.406.1 (71294) FRE
But after powering it off it didn't boot up another time.
Also there was a small damage on one of the battery pins but I think i managed to get it soldered from outside with soldering iron.
I also tried with MTTY and it didn't work either.
I got the official rom 1.48.406.1 FRE (because this phone is from swiss operator in french language) but it doesn't flash it goes to 9 % and gives error 290.
Ok, i started the thread because I actually wante to ask the question, why i'm unable to get into the Flash process from SD Card.
I formatted SD and copied the LEOIMG.nbh from official ROM and other ROM's too but when i press Reset and hold volume Down key sometimes nothing happens screen is black, sometimes im going into Bootloader with Serial shown and this text:
"Upgrade ROM code error. Please try again" and in the top right corner its written RUUNBH.
Anyone has any idea what could be problem of this device?
Btw I own LEO too and i never faced any problem till now, it was originally in German Language and i flashed it to WWE and didn't get any problems like this one.
Click to expand...
Click to collapse
Not sure if this is the problem, but what size is your SD card? I've heard, that sometimes is impossible to flash from larger cards, safest way is to use cards up to 2GB...
CaponiND said:
Not sure if this is the problem, but what size is your SD card? I've heard, that sometimes is impossible to flash from larger cards, safest way is to use cards up to 2GB...
Click to expand...
Click to collapse
Actually the sd is original 2gb that comes with hd2.
Friend, try to flash hspl 2.08 !!
Most likely that is the problem.
Enter the bootloader and connect it via usb to your usb and install 2.08 hspl (search fo it on xda developer forum)
Before instaling it read the instruction so that you know that hspl 2.08 can be installed over the old version of hspl that you installed!!
Oh and update radio to atleast 2.07
2.14 is very good
PS
Did you perform task29 before flashing?
mladen.p said:
Friend, try to flash hspl 2.08 !!
Most likely that is the problem.
Enter the bootloader and connect it via usb to your usb and install 2.08 hspl (search fo it on xda developer forum)
Before instaling it read the instruction so that you know that hspl 2.08 can be installed over the old version of hspl that you installed!!
Oh and update radio to atleast 2.07
2.14 is very good
PS
Did you perform task29 before flashing?
Click to expand...
Click to collapse
I guess I should try to install 2.08 HSPL, do you think i can use the same HSPL installer and just install 2.08 hspl from it? Because i already tried 1.66.HSPL but didn't worked.
And yes i performed task29 two or three times it finishes with some known output message which is stated on the original MTTY thread to be ignored.
Any other ideas?
gjizaqin said:
I guess I should try to install 2.08 HSPL, do you think i can use the same HSPL installer and just install 2.08 hspl from it? Because i already tried 1.66.HSPL but didn't worked.
And yes i performed task29 two or three times it finishes with some known output message which is stated on the original MTTY thread to be ignored.
Any other ideas?
Click to expand...
Click to collapse
you have to flash the HSPL back to 1.42 0000 ,then update the HSPL to 2.08 HSPL directly. if you flash it from 1.66. it can not work..pls be noted. good luck to you .hope you leo can be used again.
zengxisheng said:
you have to flash the HSPL back to 1.42 0000 ,then update the HSPL to 2.08 HSPL directly. if you flash it from 1.66. it can not work..pls be noted. good luck to you .hope you leo can be used again.
Click to expand...
Click to collapse
Ok I installed 2.08.HSPL from 1.42.HSPL and it went successfully, now i see 2.08.HSPL on bootloader but it still fails to update ROM. Stops at 8 % on the phone with rectangle mark, and on the pc it stops at 9 %.
I get Error 290 - Unknown Command
But why i cant go into sd card flash screen when i press reset and volume down ?
I just used another 2 gb microSD and added LEOIMG.nbh from official FRE ROM and it doesnt work.
Hey bud,
I was having the same problem: the flashing didn't want to start by doing a reset+vol.down. I somehow got around this by putting the leoimg.nbh on my mircoSD card, and then started the flashing from my computer by running the .exe that contains the RUU (for ActiveSync flashing). This "magically" triggered the flashing from the mircoSD card (it showed me a screen whether i wanted to update leoimg.nbh). On this screen, pressing vol.down would start the flashing through ActiveSync, and pressing the power button would start the flashing from leoimg.nbh from your microSD card. In the last case, the update on your computer will stall at 0%, this is just because you're not running the update from your computer, but from your phone. On your computer it will time-out, but the update on your phone will continue!
I hope this works! But you're doing this on your own responsibility ;p
ce3c said:
Hey bud,
I was having the same problem: the flashing didn't want to start by doing a reset+vol.down. I somehow got around this by putting the leoimg.nbh on my mircoSD card, and then started the flashing from my computer by running the .exe that contains the RUU (for ActiveSync flashing). This "magically" triggered the flashing from the mircoSD card (it showed me a screen whether i wanted to update leoimg.nbh). On this screen, pressing vol.down would start the flashing through ActiveSync, and pressing the power button would start the flashing from leoimg.nbh from your microSD card. In the last case, the update on your computer will stall at 0%, this is just because you're not running the update from your computer, but from your phone. On your computer it will time-out, but the update on your phone will continue!
I hope this works! But you're doing this on your own responsibility ;p
Click to expand...
Click to collapse
Hmmm this kinda messed me up.
What EXE file you run on the pc so it triggered update from SD ?
Because it's upossible to connect with activesync and browse to sd without the phone being fully operational (winmo running).
So i would say maby you just got it somehow with key kombination, because it would be impossible to run it the way you say. Or maby i'm wrong.
Could you be more specific about how you exactly run that process?
Thanks for your kind help. Gjizaqin
Well, whatever ROM you want to flash,
when you download this ROM, the .nbh file is packed in a .exe file.
You transfer the .nbh file to your microSD (rename to leoimg.nbh), and you can run the .exe file to flash through ActiveSync.
Because it's upossible to connect with activesync and browse to sd without the phone being fully operational (winmo running).
Click to expand...
Click to collapse
For me it was possible: reset your phone with the volume button down, to get to the tri-color screen. It shows "serial" on it. When you then connect your phone using your USB cable, it should switch to "USB", after which you can run the ActiveSync flashing.
ce3c said:
Well, whatever ROM you want to flash,
when you download this ROM, the .nbh file is packed in a .exe file.
You transfer the .nbh file to your microSD (rename to leoimg.nbh), and you can run the .exe file to flash through ActiveSync.
For me it was possible: reset your phone with the volume button down, to get to the tri-color screen. It shows "serial" on it. When you then connect your phone using your USB cable, it should switch to "USB", after which you can run the ActiveSync flashing.
Click to expand...
Click to collapse
Whell, by doing this procedure your doing normal ROM Update, and it's not doing update from sd card.
Anyways i tried this way too but not successful, its stuck on 8 % and stay's that way for about 3 minutes, than it gives me error 362 on the loader.
Anyways thanks for your help mate.
Anyone with experience can give me advice what to do with this phone?
Thanks in advance.
Gjizaqin
i'm doing task29 too... but it hang when it runs on black screen showing the percentage bar. advise is appreciated. Thanks.
whizzkid_cool said:
i'm doing task29 too... but it hang when it runs on black screen showing the percentage bar. advise is appreciated. Thanks.
Click to expand...
Click to collapse
I guess were on the same boat
gjizaqin said:
I guess were on the same boat
Click to expand...
Click to collapse
I have the same problem, tried all sorts with no luck. Can't get SD card install to work either.
Oh this sounds fun, I can no longer run active syn with my leo, the computer reports that my "usb device is not functioning properly"
I have re downloaded sync, try as I might I cant it back up and running, I wish everyone else the best of luck
This might be just a little bit off topic, but does anybody know how it is possible that some SD cards are good for flashing ROM's and other (mostly the larger) aren't?
Do you also need to copy the folder "program files" from the SD card you've flashed the ROM with to the other SD card, when you'd like to use this for your device?
jordy1990 said:
This might be just a little bit off topic, but does anybody know how it is possible that some SD cards are good for flashing ROM's and other (mostly the larger) aren't?
Do you also need to copy the folder "program files" from the SD card you've flashed the ROM with to the other SD card, when you'd like to use this for your device?
Click to expand...
Click to collapse
There has been reported problems with some 16GBmSD cards when it comes to flashing from them.
The only thing you need on the mSD card is the LEOIMG.nbh file.
dwntoearth said:
Oh this sounds fun, I can no longer run active syn with my leo, the computer reports that my "usb device is not functioning properly"
I have re downloaded sync, try as I might I cant it back up and running, I wish everyone else the best of luck
Click to expand...
Click to collapse
If you boot up your phone to Bootloader mode (but not connected to the computer), the bottom of the screen reads 'Serial'. If you now plug it into the computer, does it change to 'USB'?
Your computer error message is just saying that the computer cannot install a driver to communicate properly with your phone. Since your phone isn't fully loaded into WinMo then your computer isn't going to recognise it as a WinMo device. So don't worry about that message.
feridoun said:
I have the same problem, tried all sorts with no luck. Can't get SD card install to work either.
Click to expand...
Click to collapse
I guess this problem happen to some of the flash addicts! Problem still unsolved...
Hi guys,
my htc hd2 is giving a white screen at the startup since today,
when I press volume down and start it shows this:
PB81100 HX-BC
SPL-3.3.0000 XE
I can connect it through usb to the pc,
when trying to run hspl4 it gives me
critical error
flow 00000001
Error code 000000002
Description: USB Connect Failed.
any idea how to make it work again>
Thanks!
Are you sure it does not say SPL 3.03.0000 lol just picking I know it does as there is no SPL 3.3.0000. Any way sounds like you may need to update your drivers. You can either go to control panel and device manager and find your phone click on it to make the device drop down then right click on the dropped down device and select update drivers and then select from the internet, or go and download the latest ActiveSynce or WMDC versions as the have the updated drivers.
If this does not work try changing USB ports, changing USB cables, or even change computers. Also are you right clicking on the HSPL.exe and selecting run as administrator?
I followed all your steps, updated everything, and used hspl4 as admin
now I have this
Critical error
flow 00000006
error code: 00000014
description: unknown
any ideas
rpedro82 said:
I followed all your steps, updated everything, and used hspl4 as admin
now I have this
Critical error
flow 00000006
error code: 00000014
description: unknown
any ideas
Click to expand...
Click to collapse
Are you flashing using ActiveSynce or are manually putting your HD2 into bootloader and then flashing?
Try hspl2 (or 3 for tmous), I've seen once or twice where hspl4 fails for no known reason. (And vice versa,,, sometimes hspl4 works where hspl2/3 doesn't)
T-Macgnolia said:
Are you flashing using ActiveSynce or are manually putting your HD2 into bootloader and then flashing?
Click to expand...
Click to collapse
doing it manually
samsamuel said:
Try hspl2 (or 3 for tmous), I've seen once or twice where hspl4 fails for no known reason. (And vice versa,,, sometimes hspl4 works where hspl2/3 doesn't)
Click to expand...
Click to collapse
doesnt work with version 3 or 2 since my firmware is 3.03 he gives an error saying he doesnt find the firrmware
rpedro82 said:
doesnt work with version 3 or 2 since my firmware is 3.03 he gives an error saying he doesnt find the firrmware
Click to expand...
Click to collapse
This is a long shot here but run a Task 29 and then while you do not have a ROM on the HD2 try to run the HSPL.exe as administrator agian. Be warned that any info that is not backed up or save will be lost when you run the Task 29, so if you do not want to do it I understand.
T-Macgnolia said:
This is a long shot here but run a Task 29 and then while you do not have a ROM on the HD2 try to run the HSPL.exe as administrator agian. Be warned that any info that is not backed up or save will be lost when you run the Task 29, so if you do not want to do it I understand.
Click to expand...
Click to collapse
trying this one!
can also try downgrading the spl by flashing a correct but lower version stock rom, which would then allow you to try hspl2.
Of course, the quickest easiest (and often very successfull) thing to try would be a different PC. there are dozens of threads where people try everything for hours, no luck, but 2 minutes on a different machine and hspl is installed.
rpedro82 said:
trying this one!
Click to expand...
Click to collapse
first time it did around 14% then gave an error message saying it was corrupt,
then second, third, fotrth time it stays at 0% and says recovery failed.
rpedro82 said:
first time it did around 14% then gave an error message saying it was corrupt,
then second, third, fotrth time it stays at 0% and says recovery failed.
Click to expand...
Click to collapse
There is something that is not right here and I can not put my finger on it.
There is something not right hear but I can not put my finger on it. I got another digestion, but aftercthis one I think I am going to be tapped out. Take and run the HSPL 4 again but instead of flashing HSPL flash SPL 2.08.0000 and see if it will let you do that. If it will the you should be able to flash. SPL to it then.
T-Macgnolia said:
There is something that is not right here and I can not put my finger on it.
There is something not right hear but I can not put my finger on it. I got another digestion, but aftercthis one I think I am going to be tapped out. Take and run the HSPL 4 again but instead of flashing HSPL flash SPL 2.08.0000 and see if it will let you do that. If it will the you should be able to flash. SPL to it then.
Click to expand...
Click to collapse
tried it still error :
Critical error
flow 00000006
error code: 00000014
description: unknown
now with Task29 I get error 270 when trying to do it.
Tried on two different pcs, one vista, one xp same thing.
if someone has another idea it would be great!
rpedro82 said:
if someone has another idea it would be great!
Click to expand...
Click to collapse
Hey rpedro82, I have one more suggestion for you. Now if you don't want to try thisI totally understand as I would be a little leiry about doing it myself. Some of the other members here on XDA that have had the same issue as you of not being able to get past the splash screen and not able to flash anything. This is what they did, they toke and placed their HD2 in a sealed plastic bag and set it in the freezer for 10 to 20 minutes then as soon as they took it out they flashed their HD2. I think this helps for two reasons, one if you are having overheating issues it will of course help with that temperarily. Two cold makes things contract so if you are having a issue with the processor and the main board loading connection for whatever reason the cold allows them to restablish the connection at least temporarily.
put it in the freezer, then retried, still stays at 0%
aaarg, its so frustrating,
any more ideas someone?
samsamuel said:
can also try downgrading the spl by flashing a correct but lower version stock rom, which would then allow you to try hspl2.
Of course, the quickest easiest (and often very successfull) thing to try would be a different PC. there are dozens of threads where people try everything for hours, no luck, but 2 minutes on a different machine and hspl is installed.
Click to expand...
Click to collapse
Have you tried Samsamuels above quoted suggestion you might have luck with one of these suggestions.
Hello guys...
I really need help with this HSPL...And some expert advice too..
I have problem with my EU HTC HD2 with HSPL...
I try to put 1.42.HSPL with HSPL2_run so i can put beck stock rom but after that all thing is stuck...
My bootloader screen look like this
SYSTEM DON'T ALLOW ME TO PUT SOME LINKS..
and if i try to put beck 2.08.HSPL with HSPL2_run or HSPL4 he pop-up me some CRITICAL ERROR
Flow: 00000003
Error code: 00000004
Description: Bad model ID!
Do you know what can i do? I really need help...
Thanks a lot again..
Hi rpedro82
did you find any solution for your problem ? I'm facing the same problem and I'm still on the same point even if I tried all the members' suggestions here (even for the freezer) :/
Cheers,
GJ.
Hello friends,
This is my first question and I really need help with this one. I am not a developer but trying to learn a few things to keep up. I have an HTC Desire X which went crazy after a jelly bean update and hence I decided to do something about it. I heard about rooting and flashing phone from my boyfriend and hence I got brave and read about rooting from this forum...but really messed things up.
I tried rooting Desire X running android jelly bean using Desire_X_All-In-One_Kit_v2.0 by hasson2000. I got really excited and messed thing up. Instead of following the correct procedure, I actually tried flashing a ClockWorkMod recovery without unlocking the phone. During the flashing process, I got the Fastboot menu on my phone and so I cancelled the first command line on my PC screen. The second screen appeared but after waiting for a long time nothing happened so I got scared and removed my USB cable form the phone. Then I tried the exact procedure given in this forum. But when I did, instead of booting into the Fastboot menu, phone shows a red triangle with an '!' symbol.
I can boot into the Fastboot menu by pressing Power and Volume Down button but then my computer doesn't recognize my phone.
Please help...this phone is my life..:crying:
Before you do anything further, do you have HTC USB Drivers installed on your PC ?
Your PC running Windows 8 and below ? And is your PC has USB 2.0 ?
The screen that you show is the screen before you go to stock recovery.
You said your JB update not working right, have you try to factory reset your device after you do the update ?
Before you can do rooting and flashing ROMs, you need to unlock the bootloader first. Unlocking bootloader will make your warranty void and null. So make your decision whether you want to proceed with bootloader unlocking.
I strongly recommend not to use a toolkit but to do it yourself. You don't have exact control about what the toolkit does, also you'll learn more about the process that way. Some important things to mention further: If you decide to unlock your bootloader, do it via the www.htcdev.com site. There, you'll need a login first, after that you can proceed with the steps given to you by the site. As ckpv5 said, you need to be sure to have all the drivers installed correctly (or use a linux live cd instead). Then, after you have installed a custom recovery, take a backup of the stock firmware first before you start to change anything! That's really important, otherwise you won't be able to get back to stock anymore. Good luck!
Reply
Thank you. You guys are so quick and helpful.
Yes I did install all the drivers of HTC but still my PC wont recognise my device when in I use power button and volume down key to boot into fastboot. My computer runs on Windows 8. I have the USB drivers installed and I have also tried a factory reset of my phone but nothing works! I think what I did made something bad happen to phone recovery.
Please help
Did you read everything and tried it as we said? Do you use USB 2.0 instead of USB 3.0? DO you have the bootloader unlocked? Please answer these questions first, otherwise we can't help you much.
Reply
dansou901 said:
Did you read everything and tried it as we said? Do you use USB 2.0 instead of USB 3.0? DO you have the bootloader unlocked? Please answer these questions first, otherwise we can't help you much.
Click to expand...
Click to collapse
No. Like I said, I got excited and messed ip the steps. Instead of unlocking the phone I first tried to flash a ClockWorkMod recovery. While doing so., it tool a lot of time after showing the fastboot screen so I thought something was wrong so I disconnected the USB cable. Then I realised that I had to first unlock it so when I tried to unlock the device, instead of showing the fastboot screen my phone shows the screen whose picture I have posted in my earlier firts post. I use usb 2.0.
Please help
Hoy did you unlock? Did you register at htcdev.com for a key? Did you submit the identifier token? Try the exact procedure given here: http://forum.xda-developers.com/showthread.php?t=2076675 and read everything. also the external links, to be sure to understand what you're doing. Then, do it without using a toolkit.