HI !
I have an HD² with official Operator's ROM and my HD² never sync with my computer.
I want to know if it's possible to Flash everything without any sync (only by SD)?
Thanks a lot for my LEO
settings menu all settings connections connections usb to pc, untick "faster data". restart the pc, restart the phone.
it should now sync fine.
Thanks for the Answer, but I've already do this and the results is the same.
Sorry about my English cause I'm French
Go into Bootloader Mode (hold Volume button down while switching on the phone). You will get a tri colour screen with the word 'Serial' at the bottom of it. Plug in the USB calbe and it should change to 'USB'. If this happens then you can run HSPL and then ROMs - just ignore the conditions about making an ActiveSync connection prior to running.
I've already try this
But not exactly how you say.
I've plug the in the USB calbe when the HD2 was Off, and after loading the bootloader.
And nothing was happen.
Juste the 3 colors and the SPL version but never "USB" or "Serials", serial appears only if I don't plug the cable.
Load it into Bootloader Mode, then connect the USB cable - and see if the 'Serial' changes to 'USB'. If it doesn't, then you have a hardware problem (phone or cable or computer).
I think it's a Phone probleme.
Cause I've a Samsung wave and I havn't any problem with the same cable and the same computer.
Also I can't flash my HD²...
Sph1nxXx said:
I think it's a Phone probleme.
Cause I've a Samsung wave and I havn't any problem with the same cable and the same computer.
Also I can't flash my HD²...
Click to expand...
Click to collapse
got another pc to try? what windows you using? stock usb cable? tried all your different usb ports? remembering to right click and "run as administrator"? no usb hub? if its 64bit windows, definately try a different pc.
samsamuel said:
got another pc to try? what windows you using? stock usb cable? tried all your different usb ports? remembering to right click and "run as administrator"? no usb hub? if its 64bit windows, definately try a different pc.
Click to expand...
Click to collapse
I've already Try on another computer.
I've try with my seven OS, and with XP OS.
The problem is the same.
But when I plug the USB cable, the computer says "unknown Device" and it's the same on different computer with different cable...
I think my HD2 mother card is probably broke for this.
Related
From a noobie:
Question 1: My original problem is on soft reset my HTC xv6800 hangs at tricolor with "Serial" at the bottom of screen unless the usb cable is plugged in. It will boot to wm6.1 if I plug in the usb cable at soft reset. Then I get no USB connections in WM61, and my PC does not detect the phone at all at the usb port. I'm stuck with inability to do any sync on the phone.
I am hoping if I install a newer radio ROM it might fix the hang at tricolor with Serial, and usb connection problem. Is this reasonable or do these symptoms indicate something more grave?
Can you recommend any next steps?
Have you tried relocking the phone and flashing back to stock rom? Once you have it back to stock, see if it boots normal. If it does, go thru the steps flashing it back to custom and see if the problem comes back.
BTC
Since I've had the same stock OS ROM and verizon authorized radio ROM for several months, I assumed the ROMs were not the problem. The problem just began last week or so. What I have done is installed neuSPL2.47 wnd reflashed radio ROM and flashed TitanReloaded1.3.2.
I've checked the cable using a different device and it gets recognized by WinXP. I am now syncing with Activesync in bluetooth, and I've flashed both the OS and radio ROMs... With these steps above, is it apparent or feasible that I have a hardware usb issue on the phone?
The only issues I have are that I cannot power up the phone without a usb cable in the phone - it goes to bootloader without the cable plugged in, and I must sync via bluetooth, which is not a huge issue unless I really want to use usb for connection to PC.
Do you still think the ROMs could be the culprit?
Any ideas on why it would go to bootloader with "Serial" at the bottom unless an active usb cables is plugged in? Does anuyone know what the "Serial" message means?
What happens if you plug in the USB cable after the bootloader comes up, does it change to USB or does it keep saying serial.
It does sound like maybe your USB port is bad, if you get it booted up normally, does it see activesync in windows, does your headset work, etc?
Basically, if you use the cable trick to get it to boot, does the USB port seem completely normal then?
BTC
Flash it using your microsd
BillThyCat said:
What happens if you plug in the USB cable after the bootloader comes up, does it change to USB or does it keep saying serial.
It does sound like maybe your USB port is bad, if you get it booted up normally, does it see activesync in windows, does your headset work, etc?
Basically, if you use the cable trick to get it to boot, does the USB port seem completely normal then?
BTC
Click to expand...
Click to collapse
The port seems dead after bootup, once it gets past the bootloader. It never says USB in the bootloader. Should I see that if USB is confirmed functional? What does "Serial" mean? Activesync does not see the Titan whatsoever when using USB connection after it boots. I sometimes get an error popup at the taskbar in WinXP Pro that says the usb device has a problem...
I am having trouble with my Pc not reading my HTC HD2,when i plug the USB cable in the PC it say's device not supported.
For the last six months i have had no problem i just plug it in and i could read the storsge card in my computer with the rest of the drives ie C: D: E: ect, now it wont read at all i have windows media device centre installed and it wont pick it up either,any ideas. I can bluetooth and charge the phone no problems ,Maybe the usb cable
Thanks
with teh phone connecvted, (after it has said not supported) open up device manager on the pc, find teh entry which will have an exclamation mark, right click it and choose4 uninstal. then try it again.
also worth reinstalling windows mobile device center
Hi Samsamual
When i open windows mobile device center it does nothing even while my phone is connected,it just says phone not connected,i have uninstalled windows mobile device center a couple of times and nothing happins,it seems that when i plug phone and USB cable in the usb port or pc just wont recognise it at all.
Thanks for your reply
harv123456 said:
Hi Samsamual
When i open windows mobile device center it does nothing even while my phone is connected,it just says phone not connected,i have uninstalled windows mobile device center a couple of times and nothing happins,it seems that when i plug phone and USB cable in the usb port or pc just wont recognise it at all.
Thanks for your reply
Click to expand...
Click to collapse
He did not say open device center , he said open "Device Manager", you can open it from computer management in the control panel ...
You did say it said "device unrecognized" that means the pc is "seeing" it , just not seeing it right ...
When in device manager find ,the item that is this "unknown device" if you are not sure which it is, unplug it see what dissapears, and what reappears when you plug it back in, it may just be under usb devices or the similar ..
Then Uninstall that device, then unplug the phone, wait a few seconds and plug it back in ... also plug it right into the computer do not use a usb hub ...
Thanks watcher,i understand now i did not read it right,i will try Device Manager now.
Thanks
harv123456 said:
Thanks watcher,i understand now i did not read it right,i will try Device Manager now.
Thanks
Click to expand...
Click to collapse
Still no luck,below pic's are the messages i am getting when i plug my phone into usb port.
Note my card reader and flash drive work ok on the same usb port,so i assume its my phone or usb cable.
harv123456 said:
Still no luck,below pic's are the messages i am getting when i plug my phone into usb port.
Note my card reader and flash drive work ok on the same usb port,so i assume its my phone or usb cable.
Click to expand...
Click to collapse
i have had several experiences with usb devices malfunctioning and causing that kind of error. and a few of those times i was able to isolate the problem to a faulty cable. but those were generic usb/miniusb cables (ie not supplied with the device... just available loose in the market). if its a cable supplied by the OEM, i doubt it would fail all of a sudden. but try swapping cables and see... good thing hd2 has a standard mini usb interface...
Thanks silenced i will try a different cable tomorrow thanks for your help
harv123456 said:
Still no luck,below pic's are the messages i am getting when i plug my phone into usb port.
Note my card reader and flash drive work ok on the same usb port,so i assume its my phone or usb cable.
Click to expand...
Click to collapse
Did you right click and Uninstall the "Unknown Device" then unplug and re-plug?? ...
Yes i did all that,i got a new USB data cable today and all works fine now.
Thanks guys for all your help,this is a great forum thanks evervbody.
harv123456 said:
Yes i did all that,i got a new USB data cable today and all works fine now.
Thanks guys for all your help,this is a great forum thanks evervbody.
Click to expand...
Click to collapse
Did you solve this problem because I m getting same problem with my cable. Charging but no connection with PC or Notebook. No Memory card reading or syncronize
Straight to the point as I need this fixed ASAP.
My phone can charge via mains and USB port on my laptop.
I cannot however mount SD Card or go into USB Debugging mode. The menu on the phone does not show up at all. Only charges.
I have tried different cables including official sony ones and a few third party ones to no avail.
I tried different PC's still nothing.
On the occasion I get "USB device not recognised" but it isn't a driver fault at windows end.
Done a factory reset of the phone... still nothing.
Please help
Regards
Z3X
Z3X said:
Straight to the point as I need this fixed ASAP.
My phone can charge via mains and USB port on my laptop.
I cannot however mount SD Card or go into USB Debugging mode. The menu on the phone does not show up at all. Only charges.
I have tried different cables including official sony ones and a few third party ones to no avail.
I tried different PC's still nothing.
On the occasion I get "USB device not recognised" but it isn't a driver fault at windows end.
Done a factory reset of the phone... still nothing.
Please help
Regards
Z3X
Click to expand...
Click to collapse
I'm having the same crap.
Win7 32bit
OmegaRED^ said:
I'm having the same crap.
Win7 32bit
Click to expand...
Click to collapse
I discovered its a loose connection within the phone. try every position at the phone usb end i have to hold the USB a certain way to connect
Hi guys.
I am hoping to get some help. I flashed a custom rom about 3 weeks ago from my favourite chef as there was a newer version released. After flashing said Rom I could no longer connect my phone via USB to PC. I would get a message on PC saying USB device not recognised or failed. Tried uninstalled Device centre, different USB and PC, but nothing, still the same error. So after all that tried hard reset and Task29. I then copyied the previously used Rom to my SDcard and installed from HSPL bootloader, but still the same.
I have noticed over the last week or so, that when using WinMo instead of Android, my battery will last 3-4 hours from a full charge, with Android I get 7-8 if I am lucky.
The last problem I have is when using WinMo and I want to lock the screen, it will lock and then come back on within 1 seconds time.
Can anyone help?
Thanx
Seg
P.S: I am not blaming the Chef of the ROM for this.
Here's what I would do:
1) run task29 (SD)
2) flash 2.15.50 radio
3) Flash a ROM you KNOW works (NRG, dutty, etc...) from SD
4) Hard-reset right after flash
try to hook up your USB and see if it works.
Go into Bootloader Mode and only then connect the USB cable. Does the 'Serial' change to 'USB'?
Have you tried another USB cable?
Have you tried connecting the USB calbe to the rear USB sockets on the computer?
fred_up Go into Bootloader Mode and only then connect the USB cable. Does the 'Serial' change to 'USB'?
Have you tried another USB cable?
Have you tried connecting the USB calbe to the rear USB sockets on the computer?
I have tried all this Fred, to no avail. Different cable, different usb sockets, different pc. Still nothing.
Bootloader mode doesn't change connection type when connected.
orangekid said:
Here's what I would do:
1) run task29 (SD)
2) flash 2.15.50 radio
3) Flash a ROM you KNOW works (NRG, dutty, etc...) from SD
4) Hard-reset right after flash
try to hook up your USB and see if it works.
Click to expand...
Click to collapse
Tried all this previously mate, and still nothing. Trying again with a different ROM. I'll post back results.
Thanx guys
Seg
Still no joy, tried just about everything now.
The only way the screen will stay off is when it is plugged into charger, other than that it just dims after 10 seconds then brightens back up after 2 seconds.
Looks like the insurance will be gettinga call then.
Damn, this means I will have to use the spare Blackbery Curve we have, gutted.
Seg
I'm having an issue with my Samsung Galaxy S2 GT-I9100 (running on stock Jellybean 4.1.2) no longer connecting to the PC via USB. It had been working fine up until a few days ago.
When I connect the USB cable, it only charges the phone. It doesn't show that it is connected in MTP mode and no USB options appear in the pull down notification bar. I tried locating the phone on the computer in Windows Explorer and the Device Manager, but it wasn't there at all. There also wasn't any unrecognised device in the Device Manager.
I’ve tried the following:
Using different USB cables. Tried two official Samsung cables, a Belkin charge/sync cable and a generic cable
Plugging into different USB ports on 3 different PCs/notebooks (running on Windows 7/8)
Turning on/off USB debugging mode on the phone
Going into Settings>Wireless and networks>USB utilities. After tapping "Connect storage to USB", it will prompt to connect a USB cable even though it is already plugged in.
Booting the phone in safe mode and connecting the USB cable
Installing the latest version of KIES. I had never used the software before but gave it a try. KIES wouldn't detect the phone
Uninstalling and reinstalling the latest Samsung drivers
Dialling *#7284# for the PhoneUtil options and checking it was PDA mode under the USB option.
Turning off the phone, removing then re-inserting the SIM card and battery
Cleaning the micro USB port on the phone
I have not made any changes to the phone (or PCs), so I'm not sure what has happened for the USB connection to stop working.
Your assistance would be much appreciated.
That is very weird. Are sure you didn't change the USB connection type?
danielbe said:
That is very weird. Are sure you didn't change the USB connection type?
Click to expand...
Click to collapse
Definitely sure.
I'm wondering if maybe the micro usb port is damaged, even though there's no problems charging the phone.
That is very possible, the port can be damaged in a way that only allows charging.
Hey guys, My micro-usb was damaged so i changed it with a new one... It didn't work and phone was charging instead of Mass Storage or Debugging mode !
I thought its fake and a bad quality micro-usb so i changed it again and still have the same problem.
I have the same computer, same cable and everything is same, even the programs which i installed in both phone and pc are same, but it wont connect to pc.
My moms phone can be connected with my cable.
Ok, before i change the Micro-Usb, it was fine but not charging as good as normal. I mean at least i was able to upgrade or downgrade my android version )
Can anyone help me ? I already did a factory reset and removed the SD card. No lucks ... ( i also tried other cables and other computers, but the problem is ONLY with my damn phone )
I'm running Android 4.0.3 KH3