I was on ICS 4.0.2, I downloaded 4.1.2 and tried to install using ODIN 3.04 but it does not work... ODIN shows this...
<ID:0/004> Added!!
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> boot.bin
<ID:0/004> NAND Write Start!!
<ID:0/004>
<ID:0/004> Complete(Write) operation failed.
<ID:0/004> Added!!
<OSM> All threads completed. (succeed 0 / failed 1)
Now I can enter download mode but phone does not boot anymore...
When I start phone normaly shows:
"firmware upgrade encountered an issue. Please select recovery mode in Kies 6 try again"
Can anyone help me figure out what to do please?
Thank you
===========================================================================
And now one error shows that can't open COM port
this is weird u.u
Turn off device, pull battery, leave for 10 mins. Install kies, reboot and try ODIN again.
Also go browse forum there are plenty of topics about flashing via ODIN. Read and learn.
Guys
I flashed a ROM from Spain using Odin (I9300XXDLIH, 4.2.1 from Samfirmware) into my S3 (GT-I9300 bought in Brazil) and it works by 1 month. Then my phone starts to crash or boot by itself and finally it stop boot into Samsung screen.
I have access to Download screen, but I have NO access to recovery screen.
Now, I tried to flash a new ROM and Odin says that it has no partition. The phone doesn’t charge anymore (I need to charge using a friend’s phone).
I tried flash an old version (4.0.4) but every time I get “no PIT partition” from Odin. I also tried to flash from different version of Odin and same results.
Is there any way to solve this without getting a Service Center? Here in Brazil is difficult to find JTAG service, so I need some home solution.
Thanks and sorry for my English.
Hi, mines went exactly the same as that last week, tried everything possible software wise. sent it to samsungs ext service centre in scotland. i still dont know fr sure if there goni fix it under warranty as in download mode it says official Rom but it also says custom system. Theyve had it since last tuesday and on the repair status it still says "Acknowledge(ASC)"
heres hoping, and i hope u get urs sorted
Please feel free to find the Sudden Death thread in General section.
spamtrash said:
Please feel free to find the Sudden Death thread in General section.
Click to expand...
Click to collapse
Hi spamtrash,
As I can understand, that thread is to prevent. Now I need to recovery.
I just tried to flash a new ROM again, and I get the following:
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9300UBDLJ1_I9300UBDLI2_I9300ZTODLJ2_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/009> Odin v.3 engine (ID:9)..
<ID:0/009> File analysis..
<ID:0/009> SetupConnection..
<ID:0/009> Can't open the serial(COM) port.
<OSM> All threads completed. (succeed 0 / failed 1)
This is the first time I get that. The SetupConnection took a lot of time.
I tried to flash PIT file (do not know if it is the right PIT) and get Fail instant.
Any other help. Thanks to all.
Edit:
Now, I turned off and on again and tried to flash the same ROM:
<OSM> I9300UBDLJ1_I9300UBDLI2_I9300ZTODLJ2_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/009> Odin v.3 engine (ID:9)..
<ID:0/009> File analysis..
<ID:0/009> SetupConnection..
<ID:0/009> Initialzation..
<ID:0/009> Get PIT for mapping..
<ID:0/009>
<ID:0/009> There is no PIT partition.
<OSM> All threads completed. (succeed 0 / failed 1)
It says no PIT partition.
Finally, I tried a PIT:
<ID:0/009> Odin v.3 engine (ID:9)..
<ID:0/009> File analysis..
<ID:0/009> SetupConnection..
<ID:0/009> Initialzation..
<ID:0/009> Set PIT file..
<ID:0/009> DO NOT TURN OFF TARGET!!
<ID:0/009>
<ID:0/009> Re-Partition operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
thats mine when i try write PIT file to my phone
<ID:0/006> Odin v.3 engine (ID:6)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Can't open the serial(COM) port.
<ID:0/006> Added!!
<OSM> All threads completed. (succeed 0 / failed 1)
and when i try flash CWM here:
<ID:0/006> Odin v.3 engine (ID:6)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Get PIT for mapping..
<ID:0/006>
<ID:0/006> There is no PIT partition.
<ID:0/006> Added!!
<OSM> All threads completed. (succeed 0 / failed 1)
any suggestion
Anyone flashing a PIT file unless 100% correct is asking for trouble .
Buy a new motherboard .
jje
if theres an error in the emmc flashing the original pit file is unduly. the first thing you need is to flashing recovery to see if its working or not then there solutions such as blocking or disabling the corrupted areas in the emmc chip.
Guys,
Thanks for helping but I guess the phone is briked. I will trie the service center.
Hey everyone
Having read many threads on this issue I would appreciate help for my specific case. I got a defective device from a friend that wouldn't start anymore (introductory Samsung animation was playing repeatedly). I then tried to flash "GT-I9100_JB_ClockworkMod-Recovery_6.0.2.9" to eventually install CM 10.1.3 and then factory reset to make sure the brick bug is not an issue. However, I was not able to flash CWM, because it gets stuck at "NAND Write Start" and eventually fails (see below). Interestingly, I flashed another i9100 flawlessly only a few days ago with the exact same setting. Nonetheless I tried different Odin versions as well as different usb ports and cables.
I have no idea what kind of kernel or android version was running on the device and I can now only get into download mode.
When reading this guide I came across two problems. First, flashing a kernel - some other thread recommended "Siyah-s2-v5.0.1" - was unsuccessful. Second, I wasn't sure if I should try to flash the ICS version mentioned in this thread.
Some mentioned falling back to flashing PIT-files, but because recovery mode is not available, I cannot use the "emmc partition scanner" to identify the correct PIT-file to flash.
I would really like to save this device, so someone else may enjoy using it again in the future. Thanks in advance for any help!
Cheers
sNiXx
ODIN 3.09
Code:
<ID:0/005> Added!!
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> SingleDownload.
<ID:0/005> zImage
<ID:0/005> NAND Write Start!!
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
ODIN 1.3
Code:
<ID:0/004> Added!!
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> zImage
<ID:0/004>
<ID:0/004> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/004> Removed!!
Could anyone please help me out with this issue? I would appreciate it, if I could get the device running again.
Thanks in advance for help or tips!
Hi everyone,
almost two years ago I bought this fine device and flashed TerraSilent - being pretty happy.
After a few updates (while using wlan the gui and launcher updated themselves) the device got slower and slower.
Even during music playback it had some freezes and stutter.
Then my poweramp didn't work anymore saying I should get a licence - I bought the licence a long time before that!
So I decided to clean everything and reinstall the stock firmware to go backt to the newest TerraSilent.
Once plugged it in got into "download mode" and wanted to flash.
It started with "setup the connection" and nothing else happened. I waited for 10 more minutes and after that I turned off the device and it got bricked.
I ordered a jig USB stick and got in download mode again.
FW-file: yp-gi1cw.factoryfs.stock.tar
When I try to flash again this message appears:
<ID:0/003> Added!!
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> factoryfs.img
<ID:0/003> NAND Write Start!!
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<ID:0/003> Added!!
<OSM> All threads completed. (succeed 0 / failed 1)
Ok, then I got the PIT: YP-G1Intl.pit
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Complete(Write) operation failed.
<ID:0/003> Added!!
<OSM> All threads completed. (succeed 0 / failed 1)
Odin V3.04
After all of that I just wanted to use my Note 3 to listen to music and stuff but it sounds like ****! (Using the same headhones)
Heimdall does not find the device after that, it did before!
Can you tell me if I have an electric paper weight or is there a further chance of reviving it?
I also have read this thread but didn't really help me.
http://forum.xda-developers.com/galaxy-player/help/hard-bricked-galaxy-player-5-0-intl-t3056661
Kind regards
Flow
Hi guys, massive noob when it comes to phones.
My mother got a s4 which is locked to a specific carrier, me thinking a reinstall of android will fix the problem just finds a online way of doing it and managed to break it....
now I cant boot it back up normally and the recovery screen doesn't boot, only the download screen does.
This is what I'm doing. As you can see that re-partition is unchecked but it tried to re-partition anyway. Please help.
<ID:0/004> Added!!
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Set PIT file..
<ID:0/004> DO NOT TURN OFF TARGET!!
<ID:0/004> Re-Partition operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
won't let me add a image :/
i .imgur.com/IhK5GdN. jpg