Hi -
I regretfully managed to drop my X10 in a toilet last night.... It's been a good 9 hours since at least and although initiallly it turned on when I started to charge it now it wont.
Now the red light if flashing when it is connected to the charger, and the screen is evidently a bit moist around the edges... EDIT: the phone just turned on so part of the issue was the battery being dead, but the screen slowly got darker and darker before switching off...
Is there any test for the phone company to see if it's water damaged?
Also, if I were to call them up and say there was an issue, I know they'd replace it with a straight exchange, so they wouldn't check it first.... Is it safe to do that?
Thanks
FIRST THINGS FIRST :
TURN OFF THE PHONE. NOW. Don't hang around, pull the battery out and DO NOT PUT IT IN.
Circuits are fine when in water, it's the corrosion and also when they have an electrical current put through them that the problem arises (when wet).
This WILL be tested when sent back if you call up and claim fault. The quickest way to visually test water damage is simple. Take off the back of your Xperia and at the top, exactly center (right above the camera) you'll see either a red and white chequered square OR a full red square (possibly part red/white but blotchy).
This SHOULD be chequered red and white but with water damage it makes it all red. Simple. No chance you can claim non damage now.
SECOND.
Put the phone in a bowl of rice(uncooked white rice). Now put the bowl of rice in a warm room or cupboard (preferably where your boiler is for your house?) or on top of a heater.
Leave it overnight and if it's on a heater DO NOT TURN THE HEATER OFF. Don't put the battery in the bowl, keep the battery separate and cooler but also make sure to avoid any water areas with it.
You could be lucky (I'll assume you will be but only time will tell) and this could fix it. It's worked on all my previous phones that I've water damaged (funnily enough I've only ever water damaged SEs) and also a few other circuit board based things I've used (one of them being a laptop!).
Please turn your phone off the SECOND you have read this post. Quickest way, battery pull.
Follow all the above steps and you should have a working xperia again.
Last note : if you dont have a heater to place a bowl of rice & xperia on top of, sit your phone in an empty room, turn a hair drier on and lay it next to it on medium heat setting on the lowest speed blowing against the phone. Should work too but make sure u can shut the door (annoying noise..)
yetep said:
FIRST THINGS FIRST :
TURN OFF THE PHONE. NOW. Don't hang around, pull the battery out and DO NOT PUT IT IN.
Circuits are fine when in water, it's the corrosion and also when they have an electrical current put through them that the problem arises (when wet).
This WILL be tested when sent back if you call up and claim fault. The quickest way to visually test water damage is simple. Take off the back of your Xperia and at the top, exactly center (right above the camera) you'll see either a red and white chequered square OR a full red square (possibly part red/white but blotchy).
This SHOULD be chequered red and white but with water damage it makes it all red. Simple. No chance you can claim non damage now.
SECOND.
Put the phone in a bowl of rice(uncooked white rice). Now put the bowl of rice in a warm room or cupboard (preferably where your boiler is for your house?) or on top of a heater.
Leave it overnight and if it's on a heater DO NOT TURN THE HEATER OFF. Don't put the battery in the bowl, keep the battery separate and cooler but also make sure to avoid any water areas with it.
You could be lucky (I'll assume you will be but only time will tell) and this could fix it. It's worked on all my previous phones that I've water damaged (funnily enough I've only ever water damaged SEs) and also a few other circuit board based things I've used (one of them being a laptop!).
Please turn your phone off the SECOND you have read this post. Quickest way, battery pull.
Follow all the above steps and you should have a working xperia again.
Last note : if you dont have a heater to place a bowl of rice & xperia on top of, sit your phone in an empty room, turn a hair drier on and lay it next to it on medium heat setting on the lowest speed blowing against the phone. Should work too but make sure u can shut the door (annoying noise..)
Click to expand...
Click to collapse
thank you so much for your advice. I'll give it a go. I don't have any white rice, just brown, will that make a difference?
Of course I'll go and buy white rice if I need it!
The square at the phone is blotchy.... but mostly red. you can still see slight shades of white though.. is this possible without water damage?
Also from what you've said, I really shouldn't have put the phone to charge. I think I left it charging for ast least 6 hours so now I feel like I've ruined it by doing that..
Thanks again )
Just another update. after almost 5 hours in the rice I inserted the battery and connected it to the charger. There was an improvement from before in that the phone turned on and stayed on, ALTHOUGH th screen was flickering, and it really wasn't responding very well - I couldn't actually unlock the device.
There's a visible different in the water movement though, in that there seemed to be some spread around the whole screen initially, and now it's in a small part of the bottom of the screen.
Any tips?
Also, could someone clarify whether Vodafone would class it as water damaged?
Tuffy11 said:
Just another update. after almost 5 hours in the rice I inserted the battery and connected it to the charger. There was an improvement from before in that the phone turned on and stayed on, ALTHOUGH th screen was flickering, and it really wasn't responding very well - I couldn't actually unlock the device.
There's a visible different in the water movement though, in that there seemed to be some spread around the whole screen initially, and now it's in a small part of the bottom of the screen.
Any tips?
Also, could someone clarify whether Vodafone would class it as water damaged?
Click to expand...
Click to collapse
well you dropped it in water and now its damaged, that seems like text book water damage to me =/
Sent from my X10a using XDA App
Waiting 7 hours is not long enough...
Rice can only absorb moisture at a certain rate.
You should have wait much longer..
No offense, but your phone is toast. Rule number one is to NEVER turn on a water damaged device for at least a day after the incident. The phone was probably fine until you plugged it in.
You'll have to be on the hook for a new one. Your phone was water damaged and will not be covered under warranty.
Also, your grammar needs improvement. I found it really difficult to follow what you were writing because it made little sense.
Stop playing with it and leave it in the rice another day.
Then pray
Sent from my SAMSUNG-SGH-I897 using XDA App
They'll be able to tell
Sent from my X10a using XDA App
1. Diasassemble the Phone and put the PCB for 24hrs in 99% Isopropyle Alcohol. Not 50%, not 70% --> 99%.
2. Then take it out and let it dry for 48hrs.
3. Now reflash it (the SW is/may be corrupted).
I reanimated 80% of 200 Water-, Beer-, Pool-, Toilet-, and so on damaged Phones I repaired in the past...
Hey tuffy, sorry for the absence was at work till 10 last night then went straight to sleep lol.
I was going to give you similar advice to McKebapp however I thought the easiest option would be to give you common-to-find objects and make it easier as actually locating 99% Isopropyle is next to impossible unless you know exactly what it is!
Anyways, brown is fine - rice is rice it still takes in water. Only issue is it takes boiled water in at a rate almost 150 times faster than luke-warm or cold (which is what the water inside your phone will be).
If at all possible, do what McKebbap said but maybe avoid putting the PCB in alcohol, stick to the rice as it's bone dry and although, theoretically, so is the alcohol it'll be easier than trying to clean it all off afterwards.
If you can't dismantle it down (basically we need as much air-space between the PCB and well.. the air/rice!) then just put it back in fresh rice and leave it with the back off and battery out for another 24 hours or so, again in a warm area (needs to be warm for the water to rise).
Please, DO NOT TRY TO TURN IT ON WITHIN THIS TIME. Personally i'd actually be quite inclined to leave it for about 3 days but changing the rice (or mixing it) each day.
Good luck mate.
Oh and to answer your question : it's not possible for it to become blotchy or anything other than just squares of red/white without water buddy. it's designed for phone companies to , at a quick glance, check water damage cause guess what, besides dropping the phone, is the most common return reason ;-)
yetep said:
I was going to give you similar advice to McKebapp however I thought the easiest option would be to give you common-to-find objects and make it easier as actually locating 99% Isopropyle is next to impossible unless you know exactly what it is!
Click to expand...
Click to collapse
Each Pharmacy should have it for sale.
They maybe ask for what you'll use it.
Simply tell them the truth (cleaning electronics) or say, you'll need it to clean guitar strings from colophony.
Then everything should be fine.
So what happened? How's the phone?
How about the beer test in the good ol' days of the R310s
D3sRtH4mmR said:
So what happened? How's the phone?
How about the beer test in the good ol' days of the R310s
Click to expand...
Click to collapse
Even if it is Off Topic...
YMMD
I've still got one orange R310s I still regualry make use of.
You simply can't destroy it.
I once even went snorkeling with it.
*remembering-the-good-'ol,-Sony-free,-pure-Ericsson-times*
McKebapp said:
Even if it is Off Topic...
YMMD
I've still got one orange R310s I still regualry make use of.
You simply can't destroy it.
I once even went snorkeling with it.
*remembering-the-good-'ol,-Sony-free,-pure-Ericsson-times*
Click to expand...
Click to collapse
Indeed, the awesome days of Ericsson phones! My R380s still works!
Back on topic, I hope Tuffy11 managed to salvage the X10.
U can get isopropyl from any pharmacy. You should follow mckebapps guide. Check his posts out, he knows whats up. ;-)
Sent from my SAMSUNG-SGH-I897 using XDA App
D3sRtH4mmR said:
Indeed, the awesome days of Ericsson phones! My R380s still works!
Click to expand...
Click to collapse
Mine r520m works fine except bluetooth. In 2006 Ericsson didn't support this model anymore, so I switched to k790a that works fine for now. Even now with 3.2 Mp camera it does better job in dark sets, than X10. When I read specs I was surprised that they didn't use xenon flash. It is a kind of a bad joke for flagship model.
Returning to water damage - it is enough just to leave a phone for a week in regular room environment. Of course, I mean average environment, not like in rain season somewhere in rainforest. Alcohol (any kind - regular ethanol or isopropyl) absorbs water, but dries faster, than water, so this bath just significantly reduces water concentration. By the way, don't try to find 99% of consumer ethanol - it doesn't exist. 96% is the best (190 proof in the US or 175 degrees proof in UK). For isopropyl regular distillation gives 87.9% max. Azeotropic distillation produces higher percentage for both these spirits, but I doubt you can find it in regular stores. Closed areas, where water was suck in remain problematic. Moreover, when water finally dries out, it leaves mineral salts. It is not a big deal at circuit plates since those salts are electric safe (except sea water salts), but in clear areas like between screen layers they will be visible.
And again - if you want to kill any electronics most effective way, turn it on when it is wet. If you want to save it - be patient.
Hopefully this will help some poor schmucks that manage to do the #3 in the toilet (common enough so I call it #3).
If there is ****, just let go man, really.
If there is piss, likely more damage has been done so chances of recovery are slimmer (salty water is more conductive).
If clean water then likely the phone will work but some hardware might not survive (like the camera, ....)
In any case, remove the battery IMMEDIATELY!
Wipe battery dry. Leave alone and forget about it for 3-4 days.
Shake out as much water as possible out of the phone and let it dry for a week. You can safely use a hair dryer to warm it up to speed the evaporation. Do it twice a day.
If you want, dunk the phone in 99% rubbing alcohol for 10-20 seconds, swish it around. Take it out and forget you had a phone for 3-4 of days.
I never dropped one into the loo but I did go swimming with two phones and both survived (mostly).
Related
i accidentally spilled COFFEE on my XDA!!!!
we all have some accidents with our XDAs and mine involve coffee spilling on TOP of it or the TOUCHSCREEN...and it was still vey hot.
what happened after was this...SINCE it was WET already, i knew that if there were COULD be the possibility of SHORTS on some circuits as the UNIT was ON, anyway IT IS ALWAYS ON...no time to remove the battery immediately.
SO I removed the battery..CLEANED the EXTERNAL PARTS..then place it to to DRY awhile at room temp. after 15 minutes, since i could not wait I TURNED IT ON...AND IT BOOTED and was NORMAL....
then i started TESTING IT TO FIND OUT WHAT WAS WRONG, FINDINGS:
1. END CALL key, works like the CALENDAR KEY.
2. had ALERT that my BACKUP BATTERY was VERY LOW. (understandable, since i took out the MAIN BATT, when i viewed it, it was at 50%)
3. IT WONT CHARGE using the PORTABLE BRANDO sync and charge CABLE (well something is wrong with this cable anyway, will wait if it doesnt charge using my ORIG charger, im still at work)
4. THERE ARE GRAY SPOTS ON THE SCREEN ( i guess this is the permanent damage due to the HOT coffee)
ON THESE OBSERVATION..CAN AN EXPERT TECH PLEASE ADVISE ME ON WAS I LUCKY THAT THESE ARE THE ONLY DAMAGES AND WHAT DO I DO WITH THIS especially the SCREEN....
I think CLEANING it WITH CONTACT CLEANER WILL SOLVE some of these problems, im far fom SERVICE CENTER and the sevice for XDA here in the philippines is not that FIRST RATE either. SO ANY SUGGESTIONS PLEASE...???
Thanks
...bad luck man... sorry... (
I would say, wait couple of days, until it's really dry, and then test it again.
buzz
GOOD NEWS
Heres one to XDA DURABILITY.
well, im an impatient person and I dont like to think that MY XDA cannot survive a COFFEE SPILL, it may even survive a nuclear SPILL, hehehe.
BUT NOW MY XDA IS 100% OK....in case something like this happens to you..here is what i did.
FIRST..i forced dry it inside a high humidity airconditioned room, AN AICONDITIONED ROOM DRIES you skin...why cant it dry the insides of you XDA...heheh. JUST A SILLY IDEA.
SECOND..BUY an ELECTRONICS CONTACT CLEANER and SPRAY all AREAS that was SPILLED BY FLUID..COFFEE or WHATEVE...BETTER STILL SPRAY INSIDE THE XDA....this will dry up immediately so dont worry this will not destroy your unit. (do this with BATTERY removed)
THIRD...when you are certain that your unit is completely DRY...CHARGE it for a LONG TIME to allow the heat of charging to evaporate whatever moisture is hiding.
ON FIRST STEP...My XDA still had END key PROBLEM and SCREEN GRAY AREAS.
ON SECOND STEP...GRAY AREAS on SCREEN mysteriously vanished, and END KEY WORKS..but now..NO SOUND can be HEARD..AT ALL.
ON THIRD STEP..SOUND was restored and evrything is back to NORMAL...running for 24 hours already.
congratulatios ))))))
You've got very GOOD LUCK.
buzz
Alway remember, hot or cold drinks never mix with an XDA...
yup, i was very lucky, gosh, my XDA was really soaked.
now everythings all right and my XDA has a distinct COFFEE smell...hehehe
NICE.....MORE DECAF PLEASE....
It doesn't work, won't turn on, take out battery and plugged into charger it doesn't turn on.
I'm assuming I need a disassembly guide (looked for and couldn't find) and how to figure out what's broken and where to find parts. btw I live in Australia.
Any help is appreciated.
Thank you
There is a fix rule when electrical devices come in contact with water, you don't try to power them on and you don't try to charge them!!
The best you could do is to open the phone and let it dry out! leave it drying for days!
I suppose you could use a hair dryer...
If you are lucky it will work..if not you've probaly short circuited it...
btw, here's your guide: http://www.youtube.com/watch?v=iyT618lVxUs
Hanzo.Hasashi said:
There is a fix rule when electrical devices come in contact with water, you don't try to power them on and you don't try to charge them!!
The best you could do is to open the phone and let it dry out! leave it drying for days!
I suppose you could use a hair dryer...
If you are lucky it will work..if not you've probaly short circuited it...
btw, here's your guide: http://www.youtube.com/watch?v=iyT618lVxUs
Click to expand...
Click to collapse
never ever use a hairdryer!
just put it it down somewhere turn i around every 30 min this way it will not cause any corrosion but yeah when you sleep you cant turn itaround so before you go to bed and then after but keep the water moving it is better!
it sounds not better but it is!
like the guy above me said dont turn it on don't try to charge it
and try it over around 4-7 days
and ofc cross your fingers and pray
let us know how it goes
Fill a cup with Isopropanol Alcohol, and drop the phone in.
Seal the lid.
Leave somewhere for a could hours, shaking around a little every so often to get the fluid into every nook and cranny.
Remove phone and shake out fluid. Leave sitting wrapped in a towel in a warm place (airing cupboard etc) but nowhere too hot.
That SHOULD get all the water out, however you probably already destoyed it by plugging it in.
Put in a jar filled with raw rice or a container containing semi-powdered quicklime it will ofc absorb water and let it dry for 4-5 days and try charging or turning it on...hope my reply ain't too late
Sent from my U20i using XDA Premium App
Save Into Rice
Strange but true, you should have DIRECTLY put it in raw rice.
That will absorb the water greatly.
Put ur phone out of water. Dont turn on ur phone. Put ur device in some place by about 1 day and dont touch it!... then try again.
Rice is the answer! It sucks all the water away in a week... although i would leave it 2, just to be 100% sure
Sent from my X10mini
Sorry guys this happened like a week or two ago now. Took the battery out asap, left it for two days, hair dried it and then tried and it didn't work. I plugged it into the charger to see if it was just the battery that's ****ed, apparently just the battery is dead.
It was in a pool, so chlorine could have corroded some parts? Could I try to clean off the corrosion, replace parts etc. Or would it be cheaper to send to sony ericsson and get them to fix it?
Sony will just replace the whole phone and charge you a repair fee iirc.
Isopropanol may help with corrosion, but you need to strip the phone down to bare boards and parts, and soak it in the alcohol, then brush at with a SOFT toothbrush and gentle motions.
Isopropanol dries fast and leaves no residue, so it's ideal for loosening gunk and driving out water. I've used it with great success to salvage laptops filled with everything from cola to beer as well as waterlogged wristwatches.
dancm91 said:
Sorry guys this happened like a week or two ago now. Took the battery out asap, left it for two days, hair dried it and then tried and it didn't work. I plugged it into the charger to see if it was just the battery that's ****ed, apparently just the battery is dead.
It was in a pool, so chlorine could have corroded some parts? Could I try to clean off the corrosion, replace parts etc. Or would it be cheaper to send to sony ericsson and get them to fix it?
Click to expand...
Click to collapse
few days ago my mini pro also dripped into water i instantly removed battery
so may be damage not done to much but after that i removed water by wiping with cloth & than place it near hot air remover heater
after that i opened it thoroughly each & every part & u know water is in each & every part so i opened whole phone screen main board camera keyboard etc. & than i used hair dryer to remove water from every part of phone don't place all parts too much close to the phone or don't use hair drier for too long continuously but u can easily able to know that part is dried or not
after that in main board also u can dry it with hair dryer after u can convinced that there is no water particles remain in phone lets switch on it
after this all i done i start my phone successfully with all features working after 2 hours
& now just my keyboard lights are not working, they are working but only for 2 seconds so i have no prob with that however i give it to service center to short it out but yes this is the only solution u can get your phone working!!
if u want some help ask me
Sideromelane said:
Fill a cup with Isopropanol Alcohol, and drop the phone in.
Seal the lid.
Leave somewhere for a could hours, shaking around a little every so often to get the fluid into every nook and cranny.
Remove phone and shake out fluid. Leave sitting wrapped in a towel in a warm place (airing cupboard etc) but nowhere too hot.
That SHOULD get all the water out, however you probably already destoyed it by plugging it in.
Click to expand...
Click to collapse
This is the best solution but since its been a while now it probably wont work, and also because your already tried charging it and turning it on. Personally i would send it to say and get then to fix, but it may even be cheaper to buy a new device as basic warrenty will not cover water damage.
Cheers,
evilbarcode.
Ok so I accidently bumped my fence which had my phone on it which had a pot of water next to it. Then my phone dropped in it and i pulled it out as quickly as possible and took out the battery. FYI: My phone was still working underwater. HUGE MISTAKE. I popped in my battery to see which things worked and etc and also when i booted my phone back up the battery dropped 20%. Then i took out the battery, sim card, and sd card and let it dry in the sun. My camera is all foggy and stuff now. Can anyone help me fix my camera, speaker and battery?
*EDIT* Also my speaker was jacked up too i think because the speaker wasnt sounding very clear.
*EDIT* #2 The good news is that my battery strip thingy didnt turn red/pink. Its still white.
No problem, because you got the insurance from T-Mobile - Right?
If you do then it is covered. Water damage is specifically mentioned as covered.
If not . . . hmm, since the dot is still white you might still have a chance. Usually there is more than one though. The one near the battery is for a quick spot check, often there is also one inside for confirmation. Provided everything is ok, and it is still under warranty, maybe removing all signs of water (water marks, fog, ect.) and then attempting warranty fulfillment MIGHT work.
But my phone is rooted lol... so should i restore it before i do?
wierdoha said:
But my phone is rooted lol... so should i restore it before i do?
Click to expand...
Click to collapse
If you want, but from the several times here that I have seen where ppl send in their rooted Vibrants for warranty repair (usually GPS), it does not seem as if T-Mobile/Samsung really give a d4mn.
One word for you ...rice. put your phone in a bag of rice for 24 hours and don't touch it. After that take it out and clean it all up, put your battery back in and it should work perfect.
I actually washed my wife's phone and this worked. Hope this helps
Sent from my Simply Galaxy 3.3.....totally badass Rom!!!!
Yea right now my phone and battery is in a bowl of rice. Its been in there for about 5 hours. Hope it works
is rice like a dampness soaker?
movieaddict said:
is rice like a dampness soaker?
Click to expand...
Click to collapse
It absorbs humidity.
By the way, in the future don't put the battery back in until you've let everything dry as long as possible. Any water could short circuit the phone if you put the battery back in.
I would think also about very detailed disassembling and let dry very very well for long time before trying powering the phone.
alcohol is good for wiping off some certain parts but it can break the screen seal
Hope That Helps
Depending on your own morals, you could probably still get a warranty replacement after the water inside dries out. T-Mobile won't open the device up to check for internal water damage most likely, so if your sticker is white then you should be fine.
And FYI, bleach on a Q-Tip will turn all red water damage stickers white again.
I put my vibrant/battery in rice for 24 hours exactly and now everything works perfectly!
Speaker, battery life, camera, everything is ok
So happy.
Thanks forums!
awesome DUDE i have dropped my vibrant at least three times in water and what can i say THIS THING IS a beast my microphone doesnt work anymore but ehhh small price to pay actually does anyone know where i can find a replacement mic ive looked everywhere
XPLANE9 said:
Depending on your own morals, you could probably still get a warranty replacement after the water inside dries out. T-Mobile won't open the device up to check for internal water damage most likely, so if your sticker is white then you should be fine.
And FYI, bleach on a Q-Tip will turn all red water damage stickers white again.
Click to expand...
Click to collapse
Don't waste your time with bleach and q-tip, just ask for the replacement and when it comes, take off the new sticker with a hair dryer, 10 seconds or so, and tweezers. Then replace the water damaged one with the new one. Just like operation.
Okay....i have a black international galaxy s II converted to white and i dropped it in the water last night I was fairly intoxicated and my friend immediately helped me put it in a bowl of rice battery out etc....I left it like that overnight then tried to turn the phone on (not smart)wasn't turning on.....i came to my senses and disassembled the phone right away this morning and saw it was still a bit wet, immediately stuck it in the bowl of rice.
What it's chances at survival?? lol it was legit in water submerged for a only 1 sec if anything, i immediately snatched it out and saw that it was still turning on etc...
Also, what are warranty options? You think they'd know it was water damage after i put it back together? I also have a custom ROM and kernel and stuff but if it doesn't turn on would they be able to find out?
Hopefully the bowl of rice fixes it -.- I've had the phone for maybe like 1 month tops
Ugh so sad
Edit: fully functional luckily, no water damage, no eroding, litmus indicator is still fine and didn't change colors to indicate water damage. Close call but 100% perfect
The prognosis is not good. Warranty does not cover water damage unless you have insurance on the device. Sorry, I hope I'm mistaken for your sake!
pewpewbangbang said:
Okay....i have a black international galaxy s II converted to white and i dropped it in the water last night I was fairly intoxicated and my friend immediately helped me put it in a bowl of rice battery out etc....I left it like that overnight then tried to turn the phone on (not smart)wasn't turning on.....i came to my senses and disassembled the phone right away this morning and saw it was still a bit wet, immediately stuck it in the bowl of rice.
What it's chances at survival?? lol it was legit in water submerged for a only 1 sec if anything, i immediately snatched it out and saw that it was still turning on etc...but i could see it getting a bit wonky and crap.
Also, what are warranty options? You think they'd know it was water damage after i put it back together? I also have a custom ROM and kernel and stuff but if it doesn't turn on would they be able to find out?
Hopefully the bowl of rice fixes it -.- I've had the phone for maybe like 1 month tops
Ugh so sad
Click to expand...
Click to collapse
Sent from my GT-I9100 using XDA App
blahhh......it doesn't look like theres any water damage since i have a feeling the rice soaked a lot of water initially.
lol been going all over the web watching youtube videos etc....seeing ppl freaking submerge their galaxy s II and it still working damn.
Gonna leave it in the rice for another like 2 hrs probably then see how it does, was barely any water when disassembled, droplet here and there but that doesn't mean jack sh*t.
Im really praying it survives and works
a couple of things...
1. The battery might need replacing. Batteries are easily damaged by water.
2. Leave it rice for 4-5 days. It can never be too dry.
I would try someone's battery to see if it is still working in a couple of days.
It's not the amount of water, it's where it gets to - even a single droplet can kill a device if it shorts the right (or wrong) circuits.
Also even if it's completely dry and left in rice for a month you probably can't warranty it as there's water sensitive tabs all over modern smartphones. On the battery, usually near the headphones jack and others inside.
bunnybash said:
a couple of things...
1. The battery might need replacing. Batteries are easily damaged by water.
2. Leave it rice for 4-5 days. It can never be too dry.
I would try someone's battery to see if it is still working in a couple of days.
Click to expand...
Click to collapse
Good thing i have my OEM battery and an extra anker 1900. The first anker was in the phone so if thats messed up, I have 2 other batteries to try.
Damn 2 days -.- I'm probably gonna end up trying it tonight or something lol. Im in college and flying home on tuesday so i kinda need to find out if it'll work or not. Thanks for the help.
But damn, all those survival stores of the galaxy s II is making me both sad cuz if mine doesn't work, how the hell did theirs survive and hopeful it may work. Lol some dude had his in a full cycle washing machine, left the phone in rice for 7 days and it worked
Cactus42 said:
It's not the amount of water, it's where it gets to - even a single droplet can kill a device if it shorts the right (or wrong) circuits.
Also even if it's completely dry and left in rice for a month you probably can't warranty it as there's water sensitive tabs all over modern smartphones. On the battery, usually near the headphones jack and others inside.
Click to expand...
Click to collapse
Yea i know, I'm just trying to be hopeful lol but I'm expecting the worst, and thats that it doesn't turn on
OMG MY PHONE LIVES MUAHAHAHA YESS!!!!
Time to turn it back off and let it soak more in rice just in case. So happy right now I'm tearing
Im still gonna buy the AT&T Galaxy S II tho from craigslist lmfao and then just sell it...trading headphones plus cash for it haha
You might want to give it a blow with a hair drier.On the lowest temperature,try to make the air stream hit the whole of the board.Just to be 100% sure.
tolis626 said:
You might want to give it a blow with a hair drier.On the lowest temperature,try to make the air stream hit the whole of the board.Just to be 100% sure.
Click to expand...
Click to collapse
i've heard a hair dryer is a bad idea, reading about it on the webs. Apparently it messes with the circuit boards or w/e......air dry is the best, i just let it sit in rice for a bit longer, pretty confident all of it is dry since i took the phone apart and let it sit in the rice.
Running it now and everything is working perfectly.
Hey guys, I've been in love with my phone for the past two weeks. Now I'm on Vacay oversees. This phone is so damn light I didn't even realize they were in my swim trunks. Then boom it hit me 1 min later, phone in pocket and in the pool!!
Anyone with experience dropping it water or any advice regarding preventing further damage?
Bury it in a bowl of uncooked rice for a day or more. It will dry it out. There may be damage to the screen, or some contacts may be shorted, but this will help minimize damage. Also give it a few days to heal, some problems might go away as the last bits of water evaporate out.
sosobri said:
Hey guys, I've been in love with my phone for the past two weeks. Now I'm on Vacay oversees. This phone is so damn light I didn't even realize they were in my swim trunks. Then boom it hit me 1 min later, phone in pocket and in the pool!!
Anyone with experience dropping it water or any advice regarding preventing further damage?
Click to expand...
Click to collapse
Dont turn it on, put it in rice for 48+ hours.
During those 48 hours, pray.
Good luck!
Damp rid
Go to the hardware and get some damp rid. Place the phone in a small tupperware, place that in a larger tupperware with the damp rid in it and seal for a week. I have received 2 phones this way.
Take it apart and blowdry, that's the only way for sure, assuming you haven't tried to turn it on, good luck...
Sent from my EVO using xda premium
Put in a insurance claim and forget it.
Sent from my EVO using XDA
My OG 4G was submerged and I brought it back to life with no issues.
1. Like others have said do not turn the phone on
2. Do not blow dry the phone, if you have concerns with the contaminants in the pool water you CAN give the phone an alcohol wipe down. Alcohol evaporates quickly and can help to draw excess water out of small crevices while cleaning contacts, boards, etc
3. SETUP a drying chamber like others have recommended. Either using the rice
method or using a desiccant like Damp Rid. Put that in a shoe box along with
the phone and tightly seal it. 3 days minimum up to a full week. It took my
OG 5 days to come around.
That kind of rice works better, long grain, short grain, broken rice, Jasmine?
You need to take it apart and clean it NOW.
Pool water is highly clorinated. Chlorine is a corrosive.
Even drying it out or using rice will still damage the device. The water / chlorine are already in the device. Since its got a non removable battery the unit will still have power running to parts of it.
What needs to happen is
1, file a claim and replace it.
2. If you can get it apart. remove the battery and start to clean it with isopropoyl alchohol or contact cleaning solution.
But my guess is since it actually went underwater the LCD will have spots on it as well.
At this point its probably going to be a bad device.
easy way to turn it off, if on still, hold power for 10 sec, when in off state, hold vol down, boot into bootloader, select fastboot, select power down.
Don't use a blower that will accelerate the oxidation on the circuits.
Sent from my htc_jewel using Tapatalk 2
Thanks for the suggestions guys, I think I might have to say one good prayer in hopes of getting this device to work. Im in the Philippines so my phone doesn't have signal anyways I just mainly up use it as a wifi device, the real problem is when I get home. But if I do file a claim now maybe I'll have one waiting for me when I get back from vacation. Thanks for the help
Let the phone sit for a day or two, or until majority of the water evaporates naturally. (do not put in sun or apply direct heat, as it will make your screen fog and cause bubbles etc.) When majority of the water is out then take a blow dryer on cool or normal (not hot or warm) and apply to phone covering all areas for at least 30 mins. You need to take of the back plastic face plate as it is easy to remove and will easily hold water. If you can watch a video on how to access the batter (if you cant find one there are some for the One X line witch is very similar in build). If water is near the battery or any electrical circuits it could easily fry. If you are unsure if the water is not completely out of it you have either not waited long enough or applied enough air to the phone. Good Luck and Remember do not turn on wet electronics! THAT'S A NO-NO!!!
jr71x said:
Take it apart and blowdry, that's the only way for sure, assuming you haven't tried to turn it on, good luck...
Sent from my EVO using xda premium
Click to expand...
Click to collapse
+1
Blow dry as in a can of air. Not a blow dryer.
Don't forget a pool has chlorine in the water. It may even be worth rinsing. Then blow dry and then let it sit.
Take the rear cover off. Was gonna say remove the battery too, lol. But the sealed tupperware/bag of white rice works. Be patient as hard as that is.
water logged phone
I like the insurance claim option the best also, I suspect that if it comes around, it will never be the same again, and I would be concerned that one day, for no particular reason, it will simply stop working.
Get a new phone, and call it a day. These things happen dude
The key is to get it apart and get every bit of water out/dried, I guess I shoulda mentioned to watch aspects of things to not get hot, however a regular blow dryer on low or cool shouldn't hurt anything, it will be a delicate process. First things first though, get the battery out, do not try and turn it on. I've fixed thousands of microelectronic boards, traces, solder points, and water damage accounts for about 75% of most of what I've seen. If you aren't comfortable with this as most wouldn't be, find someone who is or try some kind of tep, tsp, whatever but it doesn't sound like that's an option... Good luck and follow up, I'd like to hear how it turns out...
Sent from my EVO using xda premium