Hey guys, I've been in love with my phone for the past two weeks. Now I'm on Vacay oversees. This phone is so damn light I didn't even realize they were in my swim trunks. Then boom it hit me 1 min later, phone in pocket and in the pool!!
Anyone with experience dropping it water or any advice regarding preventing further damage?
Bury it in a bowl of uncooked rice for a day or more. It will dry it out. There may be damage to the screen, or some contacts may be shorted, but this will help minimize damage. Also give it a few days to heal, some problems might go away as the last bits of water evaporate out.
sosobri said:
Hey guys, I've been in love with my phone for the past two weeks. Now I'm on Vacay oversees. This phone is so damn light I didn't even realize they were in my swim trunks. Then boom it hit me 1 min later, phone in pocket and in the pool!!
Anyone with experience dropping it water or any advice regarding preventing further damage?
Click to expand...
Click to collapse
Dont turn it on, put it in rice for 48+ hours.
During those 48 hours, pray.
Good luck!
Damp rid
Go to the hardware and get some damp rid. Place the phone in a small tupperware, place that in a larger tupperware with the damp rid in it and seal for a week. I have received 2 phones this way.
Take it apart and blowdry, that's the only way for sure, assuming you haven't tried to turn it on, good luck...
Sent from my EVO using xda premium
Put in a insurance claim and forget it.
Sent from my EVO using XDA
My OG 4G was submerged and I brought it back to life with no issues.
1. Like others have said do not turn the phone on
2. Do not blow dry the phone, if you have concerns with the contaminants in the pool water you CAN give the phone an alcohol wipe down. Alcohol evaporates quickly and can help to draw excess water out of small crevices while cleaning contacts, boards, etc
3. SETUP a drying chamber like others have recommended. Either using the rice
method or using a desiccant like Damp Rid. Put that in a shoe box along with
the phone and tightly seal it. 3 days minimum up to a full week. It took my
OG 5 days to come around.
That kind of rice works better, long grain, short grain, broken rice, Jasmine?
You need to take it apart and clean it NOW.
Pool water is highly clorinated. Chlorine is a corrosive.
Even drying it out or using rice will still damage the device. The water / chlorine are already in the device. Since its got a non removable battery the unit will still have power running to parts of it.
What needs to happen is
1, file a claim and replace it.
2. If you can get it apart. remove the battery and start to clean it with isopropoyl alchohol or contact cleaning solution.
But my guess is since it actually went underwater the LCD will have spots on it as well.
At this point its probably going to be a bad device.
easy way to turn it off, if on still, hold power for 10 sec, when in off state, hold vol down, boot into bootloader, select fastboot, select power down.
Don't use a blower that will accelerate the oxidation on the circuits.
Sent from my htc_jewel using Tapatalk 2
Thanks for the suggestions guys, I think I might have to say one good prayer in hopes of getting this device to work. Im in the Philippines so my phone doesn't have signal anyways I just mainly up use it as a wifi device, the real problem is when I get home. But if I do file a claim now maybe I'll have one waiting for me when I get back from vacation. Thanks for the help
Let the phone sit for a day or two, or until majority of the water evaporates naturally. (do not put in sun or apply direct heat, as it will make your screen fog and cause bubbles etc.) When majority of the water is out then take a blow dryer on cool or normal (not hot or warm) and apply to phone covering all areas for at least 30 mins. You need to take of the back plastic face plate as it is easy to remove and will easily hold water. If you can watch a video on how to access the batter (if you cant find one there are some for the One X line witch is very similar in build). If water is near the battery or any electrical circuits it could easily fry. If you are unsure if the water is not completely out of it you have either not waited long enough or applied enough air to the phone. Good Luck and Remember do not turn on wet electronics! THAT'S A NO-NO!!!
jr71x said:
Take it apart and blowdry, that's the only way for sure, assuming you haven't tried to turn it on, good luck...
Sent from my EVO using xda premium
Click to expand...
Click to collapse
+1
Blow dry as in a can of air. Not a blow dryer.
Don't forget a pool has chlorine in the water. It may even be worth rinsing. Then blow dry and then let it sit.
Take the rear cover off. Was gonna say remove the battery too, lol. But the sealed tupperware/bag of white rice works. Be patient as hard as that is.
water logged phone
I like the insurance claim option the best also, I suspect that if it comes around, it will never be the same again, and I would be concerned that one day, for no particular reason, it will simply stop working.
Get a new phone, and call it a day. These things happen dude
The key is to get it apart and get every bit of water out/dried, I guess I shoulda mentioned to watch aspects of things to not get hot, however a regular blow dryer on low or cool shouldn't hurt anything, it will be a delicate process. First things first though, get the battery out, do not try and turn it on. I've fixed thousands of microelectronic boards, traces, solder points, and water damage accounts for about 75% of most of what I've seen. If you aren't comfortable with this as most wouldn't be, find someone who is or try some kind of tep, tsp, whatever but it doesn't sound like that's an option... Good luck and follow up, I'd like to hear how it turns out...
Sent from my EVO using xda premium
Related
Hi -
I regretfully managed to drop my X10 in a toilet last night.... It's been a good 9 hours since at least and although initiallly it turned on when I started to charge it now it wont.
Now the red light if flashing when it is connected to the charger, and the screen is evidently a bit moist around the edges... EDIT: the phone just turned on so part of the issue was the battery being dead, but the screen slowly got darker and darker before switching off...
Is there any test for the phone company to see if it's water damaged?
Also, if I were to call them up and say there was an issue, I know they'd replace it with a straight exchange, so they wouldn't check it first.... Is it safe to do that?
Thanks
FIRST THINGS FIRST :
TURN OFF THE PHONE. NOW. Don't hang around, pull the battery out and DO NOT PUT IT IN.
Circuits are fine when in water, it's the corrosion and also when they have an electrical current put through them that the problem arises (when wet).
This WILL be tested when sent back if you call up and claim fault. The quickest way to visually test water damage is simple. Take off the back of your Xperia and at the top, exactly center (right above the camera) you'll see either a red and white chequered square OR a full red square (possibly part red/white but blotchy).
This SHOULD be chequered red and white but with water damage it makes it all red. Simple. No chance you can claim non damage now.
SECOND.
Put the phone in a bowl of rice(uncooked white rice). Now put the bowl of rice in a warm room or cupboard (preferably where your boiler is for your house?) or on top of a heater.
Leave it overnight and if it's on a heater DO NOT TURN THE HEATER OFF. Don't put the battery in the bowl, keep the battery separate and cooler but also make sure to avoid any water areas with it.
You could be lucky (I'll assume you will be but only time will tell) and this could fix it. It's worked on all my previous phones that I've water damaged (funnily enough I've only ever water damaged SEs) and also a few other circuit board based things I've used (one of them being a laptop!).
Please turn your phone off the SECOND you have read this post. Quickest way, battery pull.
Follow all the above steps and you should have a working xperia again.
Last note : if you dont have a heater to place a bowl of rice & xperia on top of, sit your phone in an empty room, turn a hair drier on and lay it next to it on medium heat setting on the lowest speed blowing against the phone. Should work too but make sure u can shut the door (annoying noise..)
yetep said:
FIRST THINGS FIRST :
TURN OFF THE PHONE. NOW. Don't hang around, pull the battery out and DO NOT PUT IT IN.
Circuits are fine when in water, it's the corrosion and also when they have an electrical current put through them that the problem arises (when wet).
This WILL be tested when sent back if you call up and claim fault. The quickest way to visually test water damage is simple. Take off the back of your Xperia and at the top, exactly center (right above the camera) you'll see either a red and white chequered square OR a full red square (possibly part red/white but blotchy).
This SHOULD be chequered red and white but with water damage it makes it all red. Simple. No chance you can claim non damage now.
SECOND.
Put the phone in a bowl of rice(uncooked white rice). Now put the bowl of rice in a warm room or cupboard (preferably where your boiler is for your house?) or on top of a heater.
Leave it overnight and if it's on a heater DO NOT TURN THE HEATER OFF. Don't put the battery in the bowl, keep the battery separate and cooler but also make sure to avoid any water areas with it.
You could be lucky (I'll assume you will be but only time will tell) and this could fix it. It's worked on all my previous phones that I've water damaged (funnily enough I've only ever water damaged SEs) and also a few other circuit board based things I've used (one of them being a laptop!).
Please turn your phone off the SECOND you have read this post. Quickest way, battery pull.
Follow all the above steps and you should have a working xperia again.
Last note : if you dont have a heater to place a bowl of rice & xperia on top of, sit your phone in an empty room, turn a hair drier on and lay it next to it on medium heat setting on the lowest speed blowing against the phone. Should work too but make sure u can shut the door (annoying noise..)
Click to expand...
Click to collapse
thank you so much for your advice. I'll give it a go. I don't have any white rice, just brown, will that make a difference?
Of course I'll go and buy white rice if I need it!
The square at the phone is blotchy.... but mostly red. you can still see slight shades of white though.. is this possible without water damage?
Also from what you've said, I really shouldn't have put the phone to charge. I think I left it charging for ast least 6 hours so now I feel like I've ruined it by doing that..
Thanks again )
Just another update. after almost 5 hours in the rice I inserted the battery and connected it to the charger. There was an improvement from before in that the phone turned on and stayed on, ALTHOUGH th screen was flickering, and it really wasn't responding very well - I couldn't actually unlock the device.
There's a visible different in the water movement though, in that there seemed to be some spread around the whole screen initially, and now it's in a small part of the bottom of the screen.
Any tips?
Also, could someone clarify whether Vodafone would class it as water damaged?
Tuffy11 said:
Just another update. after almost 5 hours in the rice I inserted the battery and connected it to the charger. There was an improvement from before in that the phone turned on and stayed on, ALTHOUGH th screen was flickering, and it really wasn't responding very well - I couldn't actually unlock the device.
There's a visible different in the water movement though, in that there seemed to be some spread around the whole screen initially, and now it's in a small part of the bottom of the screen.
Any tips?
Also, could someone clarify whether Vodafone would class it as water damaged?
Click to expand...
Click to collapse
well you dropped it in water and now its damaged, that seems like text book water damage to me =/
Sent from my X10a using XDA App
Waiting 7 hours is not long enough...
Rice can only absorb moisture at a certain rate.
You should have wait much longer..
No offense, but your phone is toast. Rule number one is to NEVER turn on a water damaged device for at least a day after the incident. The phone was probably fine until you plugged it in.
You'll have to be on the hook for a new one. Your phone was water damaged and will not be covered under warranty.
Also, your grammar needs improvement. I found it really difficult to follow what you were writing because it made little sense.
Stop playing with it and leave it in the rice another day.
Then pray
Sent from my SAMSUNG-SGH-I897 using XDA App
They'll be able to tell
Sent from my X10a using XDA App
1. Diasassemble the Phone and put the PCB for 24hrs in 99% Isopropyle Alcohol. Not 50%, not 70% --> 99%.
2. Then take it out and let it dry for 48hrs.
3. Now reflash it (the SW is/may be corrupted).
I reanimated 80% of 200 Water-, Beer-, Pool-, Toilet-, and so on damaged Phones I repaired in the past...
Hey tuffy, sorry for the absence was at work till 10 last night then went straight to sleep lol.
I was going to give you similar advice to McKebapp however I thought the easiest option would be to give you common-to-find objects and make it easier as actually locating 99% Isopropyle is next to impossible unless you know exactly what it is!
Anyways, brown is fine - rice is rice it still takes in water. Only issue is it takes boiled water in at a rate almost 150 times faster than luke-warm or cold (which is what the water inside your phone will be).
If at all possible, do what McKebbap said but maybe avoid putting the PCB in alcohol, stick to the rice as it's bone dry and although, theoretically, so is the alcohol it'll be easier than trying to clean it all off afterwards.
If you can't dismantle it down (basically we need as much air-space between the PCB and well.. the air/rice!) then just put it back in fresh rice and leave it with the back off and battery out for another 24 hours or so, again in a warm area (needs to be warm for the water to rise).
Please, DO NOT TRY TO TURN IT ON WITHIN THIS TIME. Personally i'd actually be quite inclined to leave it for about 3 days but changing the rice (or mixing it) each day.
Good luck mate.
Oh and to answer your question : it's not possible for it to become blotchy or anything other than just squares of red/white without water buddy. it's designed for phone companies to , at a quick glance, check water damage cause guess what, besides dropping the phone, is the most common return reason ;-)
yetep said:
I was going to give you similar advice to McKebapp however I thought the easiest option would be to give you common-to-find objects and make it easier as actually locating 99% Isopropyle is next to impossible unless you know exactly what it is!
Click to expand...
Click to collapse
Each Pharmacy should have it for sale.
They maybe ask for what you'll use it.
Simply tell them the truth (cleaning electronics) or say, you'll need it to clean guitar strings from colophony.
Then everything should be fine.
So what happened? How's the phone?
How about the beer test in the good ol' days of the R310s
D3sRtH4mmR said:
So what happened? How's the phone?
How about the beer test in the good ol' days of the R310s
Click to expand...
Click to collapse
Even if it is Off Topic...
YMMD
I've still got one orange R310s I still regualry make use of.
You simply can't destroy it.
I once even went snorkeling with it.
*remembering-the-good-'ol,-Sony-free,-pure-Ericsson-times*
McKebapp said:
Even if it is Off Topic...
YMMD
I've still got one orange R310s I still regualry make use of.
You simply can't destroy it.
I once even went snorkeling with it.
*remembering-the-good-'ol,-Sony-free,-pure-Ericsson-times*
Click to expand...
Click to collapse
Indeed, the awesome days of Ericsson phones! My R380s still works!
Back on topic, I hope Tuffy11 managed to salvage the X10.
U can get isopropyl from any pharmacy. You should follow mckebapps guide. Check his posts out, he knows whats up. ;-)
Sent from my SAMSUNG-SGH-I897 using XDA App
D3sRtH4mmR said:
Indeed, the awesome days of Ericsson phones! My R380s still works!
Click to expand...
Click to collapse
Mine r520m works fine except bluetooth. In 2006 Ericsson didn't support this model anymore, so I switched to k790a that works fine for now. Even now with 3.2 Mp camera it does better job in dark sets, than X10. When I read specs I was surprised that they didn't use xenon flash. It is a kind of a bad joke for flagship model.
Returning to water damage - it is enough just to leave a phone for a week in regular room environment. Of course, I mean average environment, not like in rain season somewhere in rainforest. Alcohol (any kind - regular ethanol or isopropyl) absorbs water, but dries faster, than water, so this bath just significantly reduces water concentration. By the way, don't try to find 99% of consumer ethanol - it doesn't exist. 96% is the best (190 proof in the US or 175 degrees proof in UK). For isopropyl regular distillation gives 87.9% max. Azeotropic distillation produces higher percentage for both these spirits, but I doubt you can find it in regular stores. Closed areas, where water was suck in remain problematic. Moreover, when water finally dries out, it leaves mineral salts. It is not a big deal at circuit plates since those salts are electric safe (except sea water salts), but in clear areas like between screen layers they will be visible.
And again - if you want to kill any electronics most effective way, turn it on when it is wet. If you want to save it - be patient.
Hopefully this will help some poor schmucks that manage to do the #3 in the toilet (common enough so I call it #3).
If there is ****, just let go man, really.
If there is piss, likely more damage has been done so chances of recovery are slimmer (salty water is more conductive).
If clean water then likely the phone will work but some hardware might not survive (like the camera, ....)
In any case, remove the battery IMMEDIATELY!
Wipe battery dry. Leave alone and forget about it for 3-4 days.
Shake out as much water as possible out of the phone and let it dry for a week. You can safely use a hair dryer to warm it up to speed the evaporation. Do it twice a day.
If you want, dunk the phone in 99% rubbing alcohol for 10-20 seconds, swish it around. Take it out and forget you had a phone for 3-4 of days.
I never dropped one into the loo but I did go swimming with two phones and both survived (mostly).
It doesn't work, won't turn on, take out battery and plugged into charger it doesn't turn on.
I'm assuming I need a disassembly guide (looked for and couldn't find) and how to figure out what's broken and where to find parts. btw I live in Australia.
Any help is appreciated.
Thank you
There is a fix rule when electrical devices come in contact with water, you don't try to power them on and you don't try to charge them!!
The best you could do is to open the phone and let it dry out! leave it drying for days!
I suppose you could use a hair dryer...
If you are lucky it will work..if not you've probaly short circuited it...
btw, here's your guide: http://www.youtube.com/watch?v=iyT618lVxUs
Hanzo.Hasashi said:
There is a fix rule when electrical devices come in contact with water, you don't try to power them on and you don't try to charge them!!
The best you could do is to open the phone and let it dry out! leave it drying for days!
I suppose you could use a hair dryer...
If you are lucky it will work..if not you've probaly short circuited it...
btw, here's your guide: http://www.youtube.com/watch?v=iyT618lVxUs
Click to expand...
Click to collapse
never ever use a hairdryer!
just put it it down somewhere turn i around every 30 min this way it will not cause any corrosion but yeah when you sleep you cant turn itaround so before you go to bed and then after but keep the water moving it is better!
it sounds not better but it is!
like the guy above me said dont turn it on don't try to charge it
and try it over around 4-7 days
and ofc cross your fingers and pray
let us know how it goes
Fill a cup with Isopropanol Alcohol, and drop the phone in.
Seal the lid.
Leave somewhere for a could hours, shaking around a little every so often to get the fluid into every nook and cranny.
Remove phone and shake out fluid. Leave sitting wrapped in a towel in a warm place (airing cupboard etc) but nowhere too hot.
That SHOULD get all the water out, however you probably already destoyed it by plugging it in.
Put in a jar filled with raw rice or a container containing semi-powdered quicklime it will ofc absorb water and let it dry for 4-5 days and try charging or turning it on...hope my reply ain't too late
Sent from my U20i using XDA Premium App
Save Into Rice
Strange but true, you should have DIRECTLY put it in raw rice.
That will absorb the water greatly.
Put ur phone out of water. Dont turn on ur phone. Put ur device in some place by about 1 day and dont touch it!... then try again.
Rice is the answer! It sucks all the water away in a week... although i would leave it 2, just to be 100% sure
Sent from my X10mini
Sorry guys this happened like a week or two ago now. Took the battery out asap, left it for two days, hair dried it and then tried and it didn't work. I plugged it into the charger to see if it was just the battery that's ****ed, apparently just the battery is dead.
It was in a pool, so chlorine could have corroded some parts? Could I try to clean off the corrosion, replace parts etc. Or would it be cheaper to send to sony ericsson and get them to fix it?
Sony will just replace the whole phone and charge you a repair fee iirc.
Isopropanol may help with corrosion, but you need to strip the phone down to bare boards and parts, and soak it in the alcohol, then brush at with a SOFT toothbrush and gentle motions.
Isopropanol dries fast and leaves no residue, so it's ideal for loosening gunk and driving out water. I've used it with great success to salvage laptops filled with everything from cola to beer as well as waterlogged wristwatches.
dancm91 said:
Sorry guys this happened like a week or two ago now. Took the battery out asap, left it for two days, hair dried it and then tried and it didn't work. I plugged it into the charger to see if it was just the battery that's ****ed, apparently just the battery is dead.
It was in a pool, so chlorine could have corroded some parts? Could I try to clean off the corrosion, replace parts etc. Or would it be cheaper to send to sony ericsson and get them to fix it?
Click to expand...
Click to collapse
few days ago my mini pro also dripped into water i instantly removed battery
so may be damage not done to much but after that i removed water by wiping with cloth & than place it near hot air remover heater
after that i opened it thoroughly each & every part & u know water is in each & every part so i opened whole phone screen main board camera keyboard etc. & than i used hair dryer to remove water from every part of phone don't place all parts too much close to the phone or don't use hair drier for too long continuously but u can easily able to know that part is dried or not
after that in main board also u can dry it with hair dryer after u can convinced that there is no water particles remain in phone lets switch on it
after this all i done i start my phone successfully with all features working after 2 hours
& now just my keyboard lights are not working, they are working but only for 2 seconds so i have no prob with that however i give it to service center to short it out but yes this is the only solution u can get your phone working!!
if u want some help ask me
Sideromelane said:
Fill a cup with Isopropanol Alcohol, and drop the phone in.
Seal the lid.
Leave somewhere for a could hours, shaking around a little every so often to get the fluid into every nook and cranny.
Remove phone and shake out fluid. Leave sitting wrapped in a towel in a warm place (airing cupboard etc) but nowhere too hot.
That SHOULD get all the water out, however you probably already destoyed it by plugging it in.
Click to expand...
Click to collapse
This is the best solution but since its been a while now it probably wont work, and also because your already tried charging it and turning it on. Personally i would send it to say and get then to fix, but it may even be cheaper to buy a new device as basic warrenty will not cover water damage.
Cheers,
evilbarcode.
During the storm this past weekend somebody (me) spilled a drink on my phone when the power went out. I immediately took the battery out and tried to dry out the phone as much as I could. The next day I powered up the phone only to find out that I could not make phone calls using the earpiece. Speaker phone and Bluetooth works fine. I also discovered that media will not play through the speaker although plugging headphones in works fine...the ringer and notifications work fine. Other than that, the phone works great. I tried flashing another ROM to see if just maybe it was a software thing...it wasn't.
The real issue is that I don't have insurance or store warranty coverage and my bootloader is unlocked. There is also signs of moisture on the phone. For now I can live with it, but I wanted to ask if anyone knew of any other options I could try. Or...maybe there is a way to redirect the sound??? Please help!!!
Lesssons learned:
1. Finish all drinks
2. Don't sit the phone next to the drink.
lilhaiti said:
During the storm this past weekend somebody (me) spilled a drink on my phone when the power went out. I immediately took the battery out and tried to dry out the phone as much as I could. The next day I powered up the phone only to find out that I could not make phone calls using the earpiece. Speaker phone and Bluetooth works fine. I also discovered that media will not play through the speaker although plugging headphones in works fine...the ringer and notifications work fine. Other than that, the phone works great. I tried flashing another ROM to see if just maybe it was a software thing...it wasn't.
The real issue is that I don't have insurance or store warranty coverage and my bootloader is unlocked. There is also signs of moisture on the phone. For now I can live with it, but I wanted to ask if anyone knew of any other options I could try. Or...maybe there is a way to redirect the sound??? Please help!!!
Lesssons learned:
1. Finish all drinks
2. Don't sit the phone next to the drink.
Click to expand...
Click to collapse
If the phone works in general... then most likely a specific piece is ruined related to the phone speaker/mic.
You can try tearing apart the phone ( I believe there are tear down guides online) and then using rubbing alcohol try to clean out any corrosion, especially around components that are having issues.
If that doesn't work, then you'll have to try to replace the component. unfortunately not sure how easy that is. Tons of components sold for iphones but doubt as much for atrix.
mysticdrew said:
If the phone works in general... then most likely a specific piece is ruined related to the phone speaker/mic.
You can try tearing apart the phone ( I believe there are tear down guides online) and then using rubbing alcohol try to clean out any corrosion, especially around components that are having issues.
If that doesn't work, then you'll have to try to replace the component. unfortunately not sure how easy that is. Tons of components sold for iphones but doubt as much for atrix.
Click to expand...
Click to collapse
Yeah, I was thinking of that as an option...being optimistic, I was gonna try to use the phone for a few days and see if it miraculously clears up...wishful thinking
I bet your Atrix will revive once the hangover subsides!
No really, it will be ok I'm sure, I've seen cases where people inmerse their devices into pools and toilets only to discover a few days later that they keep on ticking.
The clue here is to be patient and keep it from using it for several days, and I'm talking 3, 5 or even a week! So be very patient.
Remove the battery and let it dry inside a bag, box or bottle filled with uncooked rice or if you have plenty of dry bags (those that come inside some medicines or electronics) use them!
Try not to disassemble the Atrix to avoid dust contamination, but if you wan't you can go ahead and do it. The Atrix is very easy to disassemble. Just use common sense, and if you use alcohol to get rid of moisture and corrosion, be wary that even cotton or cotton swabs can be dangerous since there are components that are cold-soldered onto the motherboard and can be peeled-off very easily.
Don't use a hair dryer, since you could damage the plastic if not used correctly.
Let us know how it goes!
Sent from my Atrix using Tapatalk
I sat it in rice over night, and used a blow dryer on cool but still not dice so far. Unfortunately I don't have any other form of comms other than my Atrix...I may go and buy a cheap Go Phone to use and let the Atrix take a nap. I will be patient...I'm thinking that it will wake up one day and everything will be OK
Atrix = featherweight!!!
So if the only part that's not working at the moment is the ear speaker, then maybe you can get a spare from cnn.cn and replace it yourself. Very easy to do by the way.
The bad thing is that I think they don't sell the speaker alone, but the whole modular assembly that contains the speaker, power button and biometric scanner. But check the site above to verify.
Cheers!
Sent from my Atrix using Tapatalk
Was it a mixed or sugary drink? It could've pooled up in your speaker into something sticky. You might want to try cleaning it with alcohol disassembled. Or even dabbing it with alcohol while assembled but leave battery out and let dry at least a day. Each time you dab it with alcohol, try sopping it back up with a dry q tip.
I voided my warranty and your mum.
Unfortunately it isn't just the speaker, media will not play through the loudspeaker either...kinda weird because the speaker phone works just fine. Also, game sounds don't play. I'm thinking it might be an amplifier or something.
It was a mixed drink so it did have some sugar in it.
I dropped my atrix in the toilet. It was only in there for 2 seconds max, but I dried it off and tried to see if everything still worked. None of the speakers worked, but I put it in a bowl of rice for a couple of hours in the Texas heat, afterwards everything was working fine.
I have taken my Atrix for about a 10 minute swim, after jumping in the pool with it on my hip in an otterbox defender case. I felt something on my hip and noticed my phone there! I immediately jumped out of the pool, removed the case and battery. Dried what I could with a towel. Then put the phone in rice for about 3 hours. I then took the phone out of the rice and gave it another bath in alcohol, swishing the phone around to make sure the alcohol got every where the water got... I then let the phone sit for 4 days next to a floor vent in my house. Not directly on the vent. After the four days I tried powering the phone on. The phone powered on with no problems(no sim or memory card.) I then put my sim and memory card in, plugged in the phone and tried powering the phone on again, an it would not power on.
I then took the phone apart(not completely did not dis-connect any ribbon cables etc..) and used a q-tip and rubbing alochol to wipe any contacts that I thought might have signs of oxidation or water damage. Put the phone back together and let it sit again next to a vent for another 3 days. Put my sim, memory card and batter back in and the phone powered up with no problem.
I am currently using the atrix, the only thing that does not work is the front facing camera. It just doesn't seem to want to power up... but that is something I can live with. I did even after the 7 days had some moisture between the LCD and digitizer, so I let the phone sit in my hot car for an hour or two of an on to help get rid of the moisture.
Hope this helps.. I would recommend if you see any moisture to turn the phone off and let it sit, as if you can see moisture, there is also probably some that you cannot see and could cause more damage.
Great stories!!!
But I have to wonder how safe are we from e-coli and other bacteria/viruses when buying second hand smartphones that have visited the crapper!!!!
YIKES!!! LOL
Cheers!
Sent from my Atrix using Tapatalk
Rayan said:
Great stories!!!
But I have to wonder how safe are we from e-coli and other bacteria/viruses when buying second hand smartphones that have visited the crapper!!!!
YIKES!!! LOL
Cheers!
Sent from my Atrix using Tapatalk
Click to expand...
Click to collapse
what's really funny are people that put their phone up for public sale, are honest enough to mention that it was dropped in the toilet and still want market value and not the best offer. what kind of crap is that? it's my valuable crap?
Thanks for all of the help...you guys are the greatest...I will buy a backup before I tear the phone open...but I think cracking it open is in order...I think the moisture is gone but the sugar may have coated something.
Sent from my MB860 using xda premium
Just an update...I opened the phone and cleaned all of the contacts with alcohol...that solved the problem...thanks again for the help
Okay....i have a black international galaxy s II converted to white and i dropped it in the water last night I was fairly intoxicated and my friend immediately helped me put it in a bowl of rice battery out etc....I left it like that overnight then tried to turn the phone on (not smart)wasn't turning on.....i came to my senses and disassembled the phone right away this morning and saw it was still a bit wet, immediately stuck it in the bowl of rice.
What it's chances at survival?? lol it was legit in water submerged for a only 1 sec if anything, i immediately snatched it out and saw that it was still turning on etc...
Also, what are warranty options? You think they'd know it was water damage after i put it back together? I also have a custom ROM and kernel and stuff but if it doesn't turn on would they be able to find out?
Hopefully the bowl of rice fixes it -.- I've had the phone for maybe like 1 month tops
Ugh so sad
Edit: fully functional luckily, no water damage, no eroding, litmus indicator is still fine and didn't change colors to indicate water damage. Close call but 100% perfect
The prognosis is not good. Warranty does not cover water damage unless you have insurance on the device. Sorry, I hope I'm mistaken for your sake!
pewpewbangbang said:
Okay....i have a black international galaxy s II converted to white and i dropped it in the water last night I was fairly intoxicated and my friend immediately helped me put it in a bowl of rice battery out etc....I left it like that overnight then tried to turn the phone on (not smart)wasn't turning on.....i came to my senses and disassembled the phone right away this morning and saw it was still a bit wet, immediately stuck it in the bowl of rice.
What it's chances at survival?? lol it was legit in water submerged for a only 1 sec if anything, i immediately snatched it out and saw that it was still turning on etc...but i could see it getting a bit wonky and crap.
Also, what are warranty options? You think they'd know it was water damage after i put it back together? I also have a custom ROM and kernel and stuff but if it doesn't turn on would they be able to find out?
Hopefully the bowl of rice fixes it -.- I've had the phone for maybe like 1 month tops
Ugh so sad
Click to expand...
Click to collapse
Sent from my GT-I9100 using XDA App
blahhh......it doesn't look like theres any water damage since i have a feeling the rice soaked a lot of water initially.
lol been going all over the web watching youtube videos etc....seeing ppl freaking submerge their galaxy s II and it still working damn.
Gonna leave it in the rice for another like 2 hrs probably then see how it does, was barely any water when disassembled, droplet here and there but that doesn't mean jack sh*t.
Im really praying it survives and works
a couple of things...
1. The battery might need replacing. Batteries are easily damaged by water.
2. Leave it rice for 4-5 days. It can never be too dry.
I would try someone's battery to see if it is still working in a couple of days.
It's not the amount of water, it's where it gets to - even a single droplet can kill a device if it shorts the right (or wrong) circuits.
Also even if it's completely dry and left in rice for a month you probably can't warranty it as there's water sensitive tabs all over modern smartphones. On the battery, usually near the headphones jack and others inside.
bunnybash said:
a couple of things...
1. The battery might need replacing. Batteries are easily damaged by water.
2. Leave it rice for 4-5 days. It can never be too dry.
I would try someone's battery to see if it is still working in a couple of days.
Click to expand...
Click to collapse
Good thing i have my OEM battery and an extra anker 1900. The first anker was in the phone so if thats messed up, I have 2 other batteries to try.
Damn 2 days -.- I'm probably gonna end up trying it tonight or something lol. Im in college and flying home on tuesday so i kinda need to find out if it'll work or not. Thanks for the help.
But damn, all those survival stores of the galaxy s II is making me both sad cuz if mine doesn't work, how the hell did theirs survive and hopeful it may work. Lol some dude had his in a full cycle washing machine, left the phone in rice for 7 days and it worked
Cactus42 said:
It's not the amount of water, it's where it gets to - even a single droplet can kill a device if it shorts the right (or wrong) circuits.
Also even if it's completely dry and left in rice for a month you probably can't warranty it as there's water sensitive tabs all over modern smartphones. On the battery, usually near the headphones jack and others inside.
Click to expand...
Click to collapse
Yea i know, I'm just trying to be hopeful lol but I'm expecting the worst, and thats that it doesn't turn on
OMG MY PHONE LIVES MUAHAHAHA YESS!!!!
Time to turn it back off and let it soak more in rice just in case. So happy right now I'm tearing
Im still gonna buy the AT&T Galaxy S II tho from craigslist lmfao and then just sell it...trading headphones plus cash for it haha
You might want to give it a blow with a hair drier.On the lowest temperature,try to make the air stream hit the whole of the board.Just to be 100% sure.
tolis626 said:
You might want to give it a blow with a hair drier.On the lowest temperature,try to make the air stream hit the whole of the board.Just to be 100% sure.
Click to expand...
Click to collapse
i've heard a hair dryer is a bad idea, reading about it on the webs. Apparently it messes with the circuit boards or w/e......air dry is the best, i just let it sit in rice for a bit longer, pretty confident all of it is dry since i took the phone apart and let it sit in the rice.
Running it now and everything is working perfectly.
Last week, my friend's EVO 3D was water damaged. He was going to throw it out but I offered him $25 for it and he gave it to me. When I try turning it on, it vibrates, the buttons at the bottom light up but the screen doesn't seem to turn on. Is there any chance of fixing it?
Hmm well it might be but It's hard to tell if the board got damaged or just the screen. If u really want to fix it buy one off eBay or Craigslist with a broken screen and swap internals. At least that's what I'd do
Sent from my PG86100 using xda premium
Try drying it out totally before using it. Take the back cover off, take battery out, stick main unit in a ziploc bag full of rice and leave it alone for 3 days. The rice will suck up every last drop of moisture that would otherwise take weeks to evaporate out.
^^ awesome idea forgot to mention that rice is like a miracle worker I've saved many a phone that have taken full swims just by throwing them in a bag of rice for a couple days
Sent from my PG86100 using xda premium
Nanan00 said:
Try drying it out totally before using it. Take the back cover off, take battery out, stick main unit in a ziploc bag full of rice and leave it alone for 3 days. The rice will suck up every last drop of moisture that would otherwise take weeks to evaporate out.
Click to expand...
Click to collapse
Alright. I'll try that even though it was water damaged over a week ago. Maybe there's still some left...?
it. said:
Last week, my friend's EVO 3D was water damaged. He was going to throw it out but I offered him $25 for it and he gave it to me. When I try turning it on, it vibrates, the buttons at the bottom light up but the screen doesn't seem to turn on. Is there any chance of fixing it?
Click to expand...
Click to collapse
there is a chance. but probably would require an extensive knowledge of circuitry and i'm guessing since you don't know where to even start... probably not going to happen. lol
don't take that the wrong way by the way, it just sounds very grim to me.
cobraboy85 said:
there is a chance. but probably would require an extensive knowledge of circuitry and i'm guessing since you don't know where to even start... probably not going to happen. lol
don't take that the wrong way by the way, it just sounds very grim to me.
Click to expand...
Click to collapse
LOL. Yeah, I thought it was a long shot. I'll try the rice thing for a couple of days but I'm not getting my hopes up. I thought it was worth a try for $25
Mine survived being totally submerged in water when it fell in a puddle. at first the screen didn't work at all, then it flickered, then it had some lines on the screen, then after one day it was fully functional in every aspect haha, all I did was put it in rice, and all is well... Now I just wish I had waited to file an insurance claim, as now I'm stuck with a refurbished with 1.5
Sent from my PG86100 using xda premium
Well I would investigate some "tear down youtube videos" get the basic layout of the internals. Etc etc, maybe look into replacing the screen/digitizer
After you dry it out if screen still doesn't turn on, turn it on and leave it on for awhile, with caution... See if goes up in flames...would make an epic video if it does btw, but if something is damaged I would assume it would short out, and fry some stuff... Vibration means something is gettin power...
Shot from my sharp shooter in 3d
It's too late now to do the rice trick. If there was water on the board and the user tried to turn it on, the damage has already been done and chips were probably fried.
hitman4274 said:
Well I would investigate some "tear down youtube videos" get the basic layout of the internals. Etc etc, maybe look into replacing the screen/digitizer
After you dry it out if screen still doesn't turn on, turn it on and leave it on for awhile, with caution... See if goes up in flames...would make an epic video if it does btw, but if something is damaged I would assume it would short out, and fry some stuff... Vibration means something is gettin power...
Shot from my sharp shooter in 3d
Click to expand...
Click to collapse
the "with caution" part, here, should simply be don't turn it on at all. turning it on with water or moisture still present internally could damage it beyond repair (if that isn't the case already).
pull the battery out, and throw it in a very large, sealed Ziploc, bag of rice for a few days, maybe even longer - and cross your fingers. if it doesn't work after that. I wouldn't put anymore time and certainly not anymore money into it.
and yes it was worth a shot for only 25 bucks, for sure. I would have given it a try for that price.
I had a HD2 with the same problem. your screwed dude. Sorry. No amount rice is going to save that phone.
Yep, I think the only thing that saved mine, when it was totally submerged, is that the battery was completely dead, so nothing got power.
Sent from my PG86100 using xda premium
it. said:
Last week, my friend's EVO 3D was water damaged. He was going to throw it out but I offered him $25 for it and he gave it to me. When I try turning it on, it vibrates, the buttons at the bottom light up but the screen doesn't seem to turn on. Is there any chance of fixing it?
Click to expand...
Click to collapse
Take the phone apart and try this, with just the board, an alcohol (as pure as you can get) soak for 2-5mins then air dry (let sit for 1-2hours). Reassemble and test. As the alcohol evaporates, it extracts water out of the circuitry. But, as it has been mentioned, powering it on prior to a full dry may have already fried it.
Sent with L*W*H
Theres no science behind water damage, if you've turned it on already then it's too late for any measures to be taken.
In future, if you drop it in water, remove it straight away, remove everything from the phone, try to get as much water out as you can, then pop it in a bowl of dry rice for as long as you can, months would be best, simply assume that the phone is gone and do not switch it on until you can assure that it is completely dry, any other measures you can take seldom work but some have had results, the rice trick is as good as it gets tbh.
Avoid water like the plague with your phone.
Please help!
So I bought the HTC Evo 3D and had it for about 20 hours before I drowned it in a cup of tea (yes I was drunk) where it sat for a couple of minutes before it was discovered. As soon as it was discovered, I turned it off and removed the battery. It sat over night band in the morning I turned it back on and it works. But I immediately realized that there was still water at the bottom of the screen. I again turned it off and removed the battery and it has been sitting in rice for over a week. There is still water at the bottom of the screen! I'm so frustrated! I don't have a cell phone repair place where I live and I have no experience with working on cell phones. I have even tried using a blow dryer a little but am worried that the heat will harm the screen. My sister suggested just trying to used the phone and the heat from the phone working would evaporate the left over water but I am also afraid of frying things too. Any suggestions???
You turned it on while it was still wet. It's done for. Time for a new phone.
Sugar or colorants that were in the tea could have made that mark on the bottom of the screen
Anyway, i really don't think is there anything you can do.
Sent from my HTC EVO 3D X515m using xda app-developers app
Uncle Lizard said:
You turned it on while it was still wet. It's done for. Time for a new phone.
Click to expand...
Click to collapse
Exactly. Even if you get all the water out, you likely fried the board somewhere. If you still want an evo 3d, they are pretty old now, you should be able to get one on ebay for under 50 bucks.
You could attempt to take your phone apart and clean all the internals with rubbing alcohol but chances are your phone is past-out for ever
(Don't ask me for help as I couldn't care if your phone explodes, eh! )