I tried to update ROM trough SD
update did not end and Phone restarted
now when i tried to update rom stops on 1%
after that goes to bootloader screen
if the phone is powered off there is a triangle with "!"
How could repair it
butch_bs said:
I tried to update ROM trough SD
update did not end and Phone restarted
now when i tried to update rom stops on 1%
after that goes to bootloader screen
if the phone is powered off there is a triangle with "!"
How could repair it
Click to expand...
Click to collapse
Witch Rom version did you try to set?
Way did you it by SD and not over Active Sync?
What are the informations on the bootlouder screen?
Witch stock Rom did you have before?
I had arthemis v42
and wanted to get to 3.14
i put 3.14 on SD Card and started updating
but there was error.
i had message Updating ROM Code Error
after hard reset it desapear when try to uptade ROM from SD Card
give me "00028002 Not Allowed"
and apears bootscreen -> red green blue white
on red =>
HX-BC
SPL-1.42.0000 XE
MicroP(LED) 0x05
MicroP(TOUCH) 0x40
When try to upgrade trough sync from bootloader starts updating and on 1%
stops updating.
Tried with Task29 but stops on 19% stops and on PC says
"ERROR 270]: Update Error
The Image File Is corrupted. Please check your Update Utility"
Sir based on the information I see; I have the impression you have a branded device or a device from a otter aria than the stock rom you try to install.
In this case you need to use the GoldCard technique to install stock rom 3.14.
Take a look on how to do this on the first page of Artemis Rom; there is a step by step guide on how to install a other stock ROM version by using GoldCard.
But I don't understand way you will forced your device to instal stock ROM over SD, even when you have receeft multiple warrenties that it wassen't posible to install.
I am done. What I do? there it is:
1. Holded VolDown and started Phone to bootloader with error "Update ROM code error. Please try again."
2. Plugged USB
3. Started this
4. Windows started
5. Update to 3.14 trough PC
Well may be first time when I tried to update rom after Arthemis v42 (it needs SSPL) I am removed HSPL. I don't know is it the problem but directly installing original ROM did not help. Hope this will help someone.
No sir,
But there are some basic rules.
First of all before install stock ROM 3.14 you need to remove your HSPL version. (use HSPL2_RUN.exe and select for ex SPL 1.66)
Secondly you need to install stock ROM 3.14 over active sync (most sure procedure (especially for non users))
Note; by install stock ROM (especially with v 3.14) you need to use the one who is for your device aria/branded device. In case you take a otter version you will get Error 260.
If you have a branded device, you need to use the GoldCard technique.
Related
Hi people,
I got a problem with my hd2.. I was trying to flash it, but now i think i ****ed it up!..
First of all i did the HSPL thing.. And then i was trying to flash it with the original update 1.66 flash..
My mobile was saying that it was not allowed!
Now everytime i start my phone you get the bootloader with the message:
PB81100 HX-BC
SPL-1.66.0000 XE
MicroP(LED) 0x05
MicroP(TOUCH) 0x40
Updrade ROM code error Please try again!..
I dont know what to do right now
Please help!
and if i try a custom rom.. it says loading... all the time?
Is there someone who can help me?
Did you tray a method with SD card?
First of all you have to format a memory card to FAT32. Then put there a image of original rom. Do do so you need download stock rom from HTC and extract it. There you find a *.nbh file, the largest one. Rename it to LEOIMG.nbh and copy to your SD card.
After that put it into a phone, an enter the bootloader mode. You have to press and hold volume down key. That's all. All you need now is to follow instructions which will be displayed on screen of your phone.
yes i did.. but ill tried the original rom:
RUU_Leo_HTC_NLD_1.43.404.1_Radio_Signed_15.26.50.07U_2.04.50_22_2_Ship
But that one is saying: Not allowed :|
you are not the first one this happened to.
look here
http://forum.xda-developers.com/showthread.php?t=618084
here
http://forum.xda-developers.com/showthread.php?t=631276
here
http://forum.xda-developers.com/showthread.php?t=631053
it looks like hspl is not installed on your device with the line SPL-1.66.0000 XE on the screen. it should read SPL-1.42.HSPL XE when it is hsplled. flash the original shipped rom again from bootloader with a goldcard or reflash the hspl
redownload your rom as it might be corruped and causing a bad flash
especially look in the firstlink i gave you.
you have tried to flash 1.66 this is a WWE or ITArom. your device is not hspl-ed so it will not accept a dutch rom. you need a goldcard to flash a dutch rom again or try to reflash a stock WWe rom.
If you are Dutch or using NLD (or equavalent)
Get the official (from htc) ROM, rename the EXTENSION to .ZIP an/or open it with Winrar.
There is a .nbh file in it, wich you need to extract to (for example) your desktop.
Rename it to LEOIMG.nbh and put it on your MicroSD (wich MUST be formateed FAT32)
Put your microSD in the phone.
Start your phone in the BOOTLOADER (keep VOLDOWN pressed and shortly press POWER .. while keeping the voldown button)
Follow the instructions on screen.
Wait till all the options say OKE, even if your phone goes running trough the room, dont click anything!
(you will see some explanation marks and reboots, this is normal).
After you should have flashed SPL 1.66 and able to boot the official ROM.
But the problem is.. All the original roms doesnt work.. They Say "00028002 Not allowed"
The ROM error is because you try to downgrade 1.66 to 1.48, wich is (i think), not allowed, and would answer my own qeustion.
have you tried the goldcard method? if there is a language restriction somewhere this will solve this
I dont understand that goldcard methode.. or.. i cant find how i can do that :$
have never needed itmyself but look here
http://forum.xda-developers.com/showthread.php?t=591239&highlight=goldcard
How can i make a goldcard without a cellphone who can start? :O
same here....
my hd2 successfully hspled... ( 4 mounths ago)
after that i try to install official 3.14.405.2 Rom...
in installing progress i see a error and after restart say: software update failed please try again
now my spl is 3.03
and task29 and hspl 1 and 2 and 3 and any orginal roms NOT installed in my htc hd2...
plz help! :-D i really really confused
tighoor said:
same here....
my hd2 successfully hspled... ( 4 mounths ago)
after that i try to install official 3.14.405.2 Rom...
in installing progress i see a error and after restart say: software update failed please try again
now my spl is 3.03
and task29 and hspl 1 and 2 and 3 and any orginal roms NOT installed in my htc hd2...
plz help! :-D i really really confused
Click to expand...
Click to collapse
You need to remove SPL 3.03!!
Only way to remove is to flash stock rom over SD!
kurt-willems said:
You need to remove SPL 3.03!!
Only way to remove is to flash stock rom over SD!
Click to expand...
Click to collapse
i tried it... but not installed from sd :-S hahaha! now i have bricked hd2. who buy it?
maybe cotulla should make a new hspl that support 3.03 . true?
Same here,flashing stock ROM from the SD Card doesnt help,the SPL 3.03 is there wont let me pass through,we need a new HSPL or else throw the Phone into the garbage can and get a NOKIA.!!
now i understand this is a problem for many users... i find 3 others users that have this problem (in iranians forum)...
My problem too!
Hi guys!
I'm sure that my friends in xda can solve this puzzle soon!
I did every thing you think.
after flashing some coocked roms (last of them was dexter the dark one) I decided to flash an original,official rom - because I heared that many problems resolved in it - and it was the 3.14.405.2 version that I found direct download link here! I extracted the .nbh file and renamed it to leoimg.nbh and coppied it into my FAT32 formatted sandisk SD 8GB class2 ram and I held voldown btn and pressed pwr to enter rainbow screen, flashing started but it froze at 10 or 15 % . after this I tested many ways from xda and other helpers but my phone showed these screens:
if I just power it on:
grey danger triangle
Software update failed.
Please try again.
and if i hold voldown and press pwr:
in rainbow screen:
RUUNBH
PB81100 HX-BC
SPL-3.03.0000 XE
MicroP(LED) 0x05
MicroP(TOUCH) 0x50
Upgrade ROM code error
Please try again
and if I try to flash any ROMs(in this case 3.14.405.2 official rom)
1)with usb cable : continues to 1% and show in pc:
ERROR [262] : UPDATE ERROR
The ROM Update Utility has encountered communications error during the update process. The program will guiade you step-bye-step to recover from the errors so you can continue with the update.
"I DID RECOVERY IT WASN'T SUITABLE"
2)with SD card : whether I use rainbow screen or just pwr on my device , it
automatically start flashing and at the start it shows Loading... and in some cases it froze at this level and in other cases it shows this error:
00028002
not allow
And now my spl is 3.03 so HSPL can't do anything!(as I tested it)
tnx for your replies!!!
excuesme because of very low quality pics!
EDITED:
I did task29 too,
my phone couldn't do task29 and it froze at the beginning of the operation
it did not any changes;
mmsoftonline said:
Hi guys!
I'm sure that my friends in xda can solve this puzzle soon!
I did every thing you think.
after flashing some coocked roms (last of them was dexter the dark one) I decided to flash an original,official rom - because I heared that many problems resolved in it - and it was the 3.14.405.2 version that I found direct download link here! I extracted the .nbh file and renamed it to leoimg.nbh and coppied it into my FAT32 formatted sandisk SD 8GB class2 ram and I held voldown btn and pressed pwr to enter rainbow screen, flashing started but it froze at 10 or 15 % . after this I tested many ways from xda and other helpers but my phone showed these screens:
if I just power it on:
grey danger triangle
Software update failed.
Please try again.
and if i hold voldown and press pwr:
in rainbow screen:
RUUNBH
PB81100 HX-BC
SPL-3.03.0000 XE
MicroP(LED) 0x05
MicroP(TOUCH) 0x50
Upgrade ROM code error
Please try again
and if I try to flash any ROMs(in this case 3.14.405.2 official rom)
1)with usb cable : continues to 1% and show in pc:
ERROR [262] : UPDATE ERROR
The ROM Update Utility has encountered communications error during the update process. The program will guiade you step-bye-step to recover from the errors so you can continue with the update.
"I DID RECOVERY IT WASN'T SUITABLE"
2)with SD card : whether I use rainbow screen or just pwr on my device , it
automatically start flashing and at the start it shows Loading... and in some cases it froze at this level and in other cases it shows this error:
00028002
not allow
And now my spl is 3.03 so HSPL can't do anything!(as I tested it)
tnx for your replies!!!
excuesme because of very low quality pics!
EDITED:
I did task29 too,
my phone couldn't do task29 and it froze at the beginning of the operation
it did not any changes;
Click to expand...
Click to collapse
exactly THE SAME THING
flashing to offical wont help either
Hello all... tried to be a little geek and installed a custom Rom (Artemis V32 with radio 2.12.50.02_2) and that went ok. Then I copied an Android version to my sd card, and that went also ok.
Then I installed a bootloader so I could choose Android or WM, that went ok too.
But since then I had some regular crashes in Android and also with WM.
I decided to install a stock Rom (found via Usenet; Stock ROM (NLD) 1.72.172.0 met radio 2.07.51.22_2 en SPL-1.66.0000 ) and things went bad.
I have tried all kinds of things so resolve the issue:
- Put the stock rom on the sd card (formatted fat32, size 4gig) and renamed it to loeimg.nbh and started it up with the volume button down: no success
Message:
PB1100 HX-BC
SPL-1.66.0000 XE
MicroP(LED) 0x05
MicroP(TOUCH) 0x40
- Connected the hd2 with the original cable to my pc (Windows 7 Ultimate, and tried also WinXP SP3) and tried to install it via the .exe file from another stock rom I downloaded via the HTC website.No succes, the software starts-up, I can click yes, next, click yes again at "I completed the steps indicated above" and then I get the screen current information about your pda phone Image version does not mention any version at this point.
If I then click on update I get the screen that says from image version: to image version.
The from version is not filled in, so I think the fault has something to do with this.
After I clicknext 2 times I get the progress screen, but nothing happens then anymore. It keeps showing 0%
If anyone can help me out with this it would appreciate it a lot! And if you need any additional info, please let me know...
Thanks in advance,
Friendly greetings...
you no longer have hspl installed. It was removed by the (failed) stock rom from sd card flash attempt. In bootloader, see your spl ends .0000? that tells you hspl is gone.
Manually enter bootloader, connect usb, count to 20, run hspl2(right click run as administrator), choose 2.08.hspl.
When it completes, re enter bootlaoder (hold down vol as the phone restarts at 100%), wait for bootloader, wait for the word serial -> usb, run your rom flash over usb.
Thanks for the quick reply... as soon as I'm back home I'm going to try it out.. I'll post the result here..
something similiar happened to me some months ago..
should work
DN41
oh, and the reason the "from version" is blank is because that is read from the registry, but we put the phone in bootloader ourselves first so it can't see the registry. that's also why when you flash radios you see rom version info there. it can be ignored.
Do not forget to remove loeimg.nbh from your memory card before trying to flash under windows.
Thanks for the reactions... great to know I am not alone in this...
I performed the actions as described and I got the message "we hacked it"
I then tried to install a stock rom I downloaded but my phone turned off then at 11%
I have the idea that my battery is not loading anymore as I can't see the orange led burning when connected to the adapter/computer.
Ordered a new battery yesterday evening and will receive it normaly/hopefully today by mail. Then I will try again and share the results.
Thanks again all for the great support so far...
check the battery pins closely, hundreds of people have bent them poppng the battery out.
Ok, checked the connection of the pins.. these are ok I think.
Battery-led is still not showing went connected to usb.
So now my screen states the following:
PB81100 HX-BC
SPL-2.08.HSPL 8G XE
0x05
CottulaHSPL 0x40
What rom can I now install? Only an official one?
I tried to download an official rom from the htc website (after inserting my serial), but when I run the
RUU_Leo_Vodafone_NL_1.72.172.0_Radio_CRC_Signed_15.32.50.07U_2.07.51.22_2_Ship it shows a message that the file is corrupt.. and this for about 6 times now...
I feel the noob-level is rising extremely now...
TitusV said:
What rom can I now install? Only an official one?
SPL-2.08.HSPL 8G XE
Click to expand...
Click to collapse
.hspl means hspl is installed so you can flash any rom.
I tried to download an official rom from the htc website (after inserting my serial), but when I run the
RUU_Leo_Vodafone_NL_1.72.172.0_Radio_CRC_Signed_15.32.50.07U_2.07.51.22_2_Ship it shows a message that the file is corrupt.. and this for about 6 times now...
(
Click to expand...
Click to collapse
all i can say is try another rom. just stick to usb flashing, protect hspl.
Hi
I have a flashed HD2 with these problems.
In Bootloader it says
PB81100 SS-BC
SPL-208.HSPL 8G XE
0X05​CotullaHSPL 0X50
If I try to install HTC RUU_Leo_S_HTC_GER_3.14.407.2_Radio_15.42.50.11U_2.15.50.14_LEO_S_Ship.exe it breaks after 1% it says 270 error
HD2 reboots and again white Screen. When I put off/on battery and press Volume down I see bootloader display.
I tried to flash with sd Card, leoimg.nbh on the sdcard breakes after 10%
it says
00018003
LEOIMG.nbh -FAIL
Radio-Fail
I think I have a bootloader problem. How can I remove SPL-2.08.HSPL 8G XE and set the new orginal SPL ?
here bepe says :
4) Uninstallation
Only way to remove the HSPL is to flash an original SPL from SD card.
- Take any "RUU_signed.nbh" from a ship ROM and copy it to SD card.
- Rename it to "leoimg.nbh"
- Reset the device while pressing the volume down button.
Click to expand...
Click to collapse
http://forum.xda-developers.com/showthread.php?t=611433
I made it with HTC
RUU_Leo_S_HTC_GER_3.14.407.2_Radio_15.42.50.11U_2.15.50.14_LEO_S_Ship.exe
but I can't remove HSPL from my bootloader.
How can I set my bootloader back to original htc ?
the topic can be closed
this has solved my problem
http://forum.xda-developers.com/showthread.php?p=24876999#post24876999
I had installd Windows 6.5 everthing was working perfect, then I tried to install Android and clk mod now I get the same in the 1. Posting from me.
I have SPL-3.03 HSPL in the boatloader but I get allways Error 270 I can't uninstall 3.03 HSPL
does anybody have an Idea?
Radio_2.15.50.14.nbh installation fails, but custom rom like energy sucesses. After that again white screen
nobody knows the solution?
You have a stuck radio. Fairly common, with a variety of symptoms. The radio wont let itself be changed which is why custom roms and splashscreens don't have a problem.(radio gets flashed at the start of flashing which is why it always fails around 8-10%) This issue can affect spl to a greater or lesser degree, some people can change spl some can't, some find flashing an older (but correct for that phones cid and region) stock rom, some find chilling the phone allows the flash to take allowing the radio to finally change, some never get anything to flash again.
hi
thank you for your answer. My Bootloader shows
SPL-3.03.HSPL XE
0X05
0X50
if I try to run Task29 via USB Cable, I get Error 270, it breaks sometimes at 16%
reflash 3.03 HSPL with HSPL 4 says it is successfull, but if I try to flash a rom with usb again it shows 270 Error, so my logical deduction is, reflash with HSPL4 does not really flash and it gives wrong answer because others like task28 leo customRUU can't flash over usb cable. HSPL 4 says success but this answer must be fake, after reboot 3.03HSPL remains in the bootloader, I tried to downgrade to 2.08HSPL no chance,
My System is Windows XP SP3 when I connect USB Cable to my HD2 it shows USB in the bootloader but why does it break if I try to flash over USB Cable and give an error 270 ? there must be a connection problem between my laptop and HD2.
I would like to know
Is there any way to flash HSPL4 over microSD card?
Can I see which Radio Rom has been installed ?
its a bit strange
Radio Rom Radio_2.15.50.14 istallation via USB Cable fails after 4%
and via microSD Card ~96-99%
I get
00018003
what can be the reason?
ParmakSokan said:
what can be the reason?
Click to expand...
Click to collapse
as i said,. you have a radio image that isnt allowing itself to be overwritten. My name for it is 'stuck radio' and some people fgind the radio still works fine with, for example, custom roms, it just cant be changed, others find the phone always hangs on grey bootscreen, yet more find taht hspol/spl flashes seem to work but nothing changes, some find chilling it in teh freezer lets a rom flash and suddenly all is well, and yet more find the freezer trick seems to work but doesnt, and yet more try and try and try to sd card flash with their CORRECT stock rom and suddenly without warning teh flash works.
My advcie, Prepare yourself for disappointment, but keep trying,and most importantly READING there are hundreds of threads about this.
mobile radio
ParmakSokan said:
nobody knows the solution?
Click to expand...
Click to collapse
hey gys whats this radio in mobiles... have searched and searched but no ans.....
hello. i have been flashed android. and yesterday my sense of screen started to not work. now i wanna back to original rom and go to warranty, and i tried to flash leoimg.nbh from sd card, but i have error "software update failed" "00028002" "upgrade rom code error please try again" and etc. my spl 3.03.0000 . please help. and sorry for my bad english
and when im trying to install rom by usb it loads 1% and then phone went black and installation stops. please help me some 1
Get hspl4
Get unbranded wwe 3.14 rom
Into bootloader
Connect USB
Run hspl4 - choose 3.03.hspl
Reboot into bootloader
USB
Run the 3.14 install over USB
Reboot into bootloader
USB
Hspl4 - choose 3.03.0000
Done.
Or.......
Use the correct rom (using the wrong rom is why you're having problems)
unable to flash 3.27 rom on my htc hd2 ........its a t mobile product but unlocked as i use it in india so i tried to flash asia version but it start and completes only 8% thn nothing happens and gives error [262]:which says
UPDATE ERROR
This error occurs during the CE ROM code upgrade process.
Solution: If this happens, you can just soft-reset the device and run RUU again. The update process will then continue.
Note: At this stage, the Wince is destroyed; instead, it is in upgrade mode
Its goes to the tri color screen where it says upgrade ROM code error Please try again.
Plz help
in download mode it says:
PB81110 HX-BC
SPL-2.08.HSPL 8G XE
0x05
CotullaHSPL 0x50
your device is CID locked which stops none t-mobile roms flashing.
First thing you MUST DO is check what version HD2 you have:
if it has green & red, call/end keys it is the t-mobile USA version (TMOUS) & flashing the wrong radio on that model will result in a bricked device.
if you have standard model with white icons on keys then you will need install HSPL prior to flashing the ROM update, HSPL will bypass CID fixing 262 error ...
HSPL & ROM links for all models including ROM direct download links for TMOUS HD2 can be found in HD2 wiki.
Go look & read it all & be sure you know what you doing before proceeding to flash ...
can u tell me how to unlock cid and can this screen tell me about the rom whether it is 512 or 1024.....
I see you have HSPL already.
are you flashing from computer or trying sd card flash ?
I would also assume it is 512 EU version from details above
try the latest HTC Generic WWE ROM from Wiki section & perhaps try HSPL4 to reflash HSPL as maybe corrupted nand issue. Also do flash from PC via USB cable & make sure PC has activesync or WMDC installed (all can be found in HD2 Wiki)
i m flashing it from my pc as my phone doesnt start when i switch on it stuck on screen saying SOFTWARE UPDATE FAILED PLZ TRY AGAIN......
i tried to flash HSPL4 but it gave me error http://prntscr.com/1stcv1 ......
n also i have WMDC but i doesnt show up my phone but in tri color screen mode it shows usb....
yes it hav 512 rom
Sounds like corrupted nand & model id is perhaps corrupted too.
Try resetting via reset button.
Have a look at these thread:
http://forum.xda-developers.com/showthread.php?t=1001452
http://forum.xda-developers.com/showthread.php?t=1182215&page=2
thanx a lot......just performed task29 and got htc white screen and now can u tell me which rom to flash n can i make it converted to android:good::good::good::good:
First get it fully working on a WM6.5 ROM & test it for 2 or 3 days, then if good look at the Android nand section & look for a Android build you like & has good feedback & current support.
Post 4 above has a link to an HD2 HTC generic WM6.5 ROM but you can choose something else if needed by looking at the ROM links in the HD2 Wiki
xdriver said:
thanx a lot......just performed task29 and got htc white screen and now can u tell me which rom to flash n can i make it converted to android:good::good::good::good:
Click to expand...
Click to collapse
Hello xdriver,
if you want Android on yor phone you mighr opt for installing via NativeSD method, giving you the advantage of trying out different builds and choosing the one that suits your needs at best. Also, if somwthing goes wrong you always have WM fully functional on NAND. But consider buying a decent SD card first, meaning one with exceptional good random r/w access speed. You'll find tutorials in the SD section.
Have fun!
Best regards
Getrid…
Sent from my HTC HD2 using xda app-developers app
thnx 4 the info frnds but after doing task29 thn also it stuck at 8% and give same error stated in post #1 and now my phone doesnt start up when i switch it on it vibrates for 3-4 secs n nothing happen after i tried to flash wwe asia india ROM ............... maybe it is battery problem now i charging it to check the prob...........
its getting into the bootloader mode now i m download a lower version of ROM .......Hope it works