Hello guys i was about to flash my x10 mini pro but when i pluged in my phone it told me i have an update so i started it . everything was ok until step 3 , i did shut down my phone and i pressed the back button and connected the usb cable but it says downloading and the phone starts up after a minute and it says u have updated ur phone but nothing happend ... sty for bad english
Related
Help... i just dont know what happen, i've been using the Cyanogen 6 v3.2.1 for a week now, and just so suddenly today, i didnt do anything to my phone, after it reboot on its own, error pop out saying
"The Application DSPManager has stop responding unexpectedly, please try again."
and its looping whenever i press force close. i cant even boot to xrecovery to restore my os. cant even detect my x10 mini pro whenever i plug to usb cable...
i dont know how to do anything now...
Try to press quickly the on/off button and then reboot .
Why do you can't go xrecovery °° ?
Its ok now, i've re-flash using SEus with the help of my friend.
Im not even sure my self why I cant boot to xrecovery since its pre installed with the cm6.
Sent from my Sony Ericsson Xperia X10 Mini Pro using XDA App
My xperia x10 mini (no pro) have a bricked, i have 3 days tryng to revive, but nothing: I use: Byn4ri flash, Seus, Pc Companion, Diferent mode of install original roms, and now, in the flash tool dont detect my phone? what happen? HELP PLEASE I NEED OF ALL OF YOU.
Does the led of your phone flash the red colour three times? The red led flash three times because your phones battery is dead. So you plug in your phone with usb cable to the computer and let it remain for two or more hour (this means that you're charging your phone )During this time the phone would not turn on and you can do nothing with your phone during this time. You will only see the red led . After two hours of charging disconnect and run seus and Follow the onscreen instruction. I followed the above mentioned procedure and I got my mini back .
Sent from my stunning x10mini !
[MINICM 1.0.2 with CWM]
(Any problem ? Feel free to contact me - [email protected] , +919033451101)
I tried to update my x10 to 2.3 this morning, already reach the 3rd step which I have to press and hold the back key and plug in the cable. After plug in it was ok, but load till halfway it pop out "An error occurred" and asked to retry. I press the retry button still unable to continue with my update. When I unplug it from my com, my x10 unable to on now What should I do? Help me. It just appeared Sony Ericsson and some yellow screen and off by itself again. I am using the official update by se pc companion.
my x10 also same problem..?Help needed..?
My X10 also same problem, please help us dear developers.....?
Try the repair option of the updating service (not pc companion) or flash stock rom with the flash tool
http://forum.xda-developers.com/showthread.php?t=928343
hey guys while I was falshing my rom of xperia x10 via flashing tool follwed the procedures given after it completed and asked me to unplug the device and switch it on... now phone dos not boots and has got stuckd at sony ericsson logo...its not moving ahead... not even booting.. I ve tried to connect again in flashing tool flash mode still its not working .. phone automatically gets disconnected.. also wen I put the battery inside it turns on to sony ericsson logo automatically even if I dnt use power on button.. help me out... plz plz plz
Please give some info.
Have you unlocked bootloader?
What rom are you trying to flash?
When you start to flash, flashtool asks for disconnect the phone, power off and connect again with BACK button pressed. Then the process continues...
After flashing kernel you must enter to recovery and install zip file from sd-card.
Regards.
I was tryng to flash rom 3.0.1.G.0.75 on Gingerbread 2.3.3 and ya I was supposed to enter downloading mode but before I do dat phone has stuckd on... gets on wid sony ericsson logo evn if I dnt swtch on...help me..
Please, can you provide the followed procedure ?
Maybe this thread can help you http://forum.xda-developers.com/showthread.php?t=1226826&highlight=lock+bootloader+again
Which log do you use, PC Companion, SEUS, Flashtool...?
Do you have a CWM recovery ?
If you don't know how (or are afraid) to use flashtool...
You can do that :
1/ Launch SEUS (Sony Ericsson Update Service) HERE
or PC Compagnion HERE
2/ Turn off your phone, remove the battery over 5 seconds, replace it.
3/ Hold the right button (the one with the arrow) and plug your phone on your computer with usb (It calls flashmode)
4/ The green led must be light on and SEUS or PCC recognize your phone...
5/ Now you just have to follow the instructions to install a stock rom.
If it doesn't help, you can use flashtool... A great tuto HERE Thanx to Crowds
With it you can unlocked the bootloader and install a new kernel with CWM recovery inside...
Install a new rom, root your phone... ans so more stuffs...
I hope it helps...
I've been told to install x recovery on the computer,take out battery n unplug the phone .Then have flash base band on computer(it will then show that its trying to download)connect phone in flash mode.to do this hold down the bottom right hand button(the back arrow)on your phone then put battery back in(KEEP HOLDING back arrow button)and plug the cable back into your phone.I hope this helps.GOOD LUCK BUDDY!
I am having the same problem with my Xperia Neo, i tried to connect my phone to PC Companion and it says. "PC Companion was unable to connect to your phone, please disconnect and connect again"
My phone is just sitting there with the words "Sony Ericsson" flashing on and off, I fear that my phone is bricked but im not 100% sure, if there is anything that can be done please help!!!
Can you explain more what you're doing ?
Do you did that :
Launch Pc Compagnion
Plug the phone
Mount the sd card
EDIT : Sorry i read too fast your post... Your phone can't turn on you're stuck on the bootlogo of SONY ERICSSON...
Do you plug the phone in flashmode ?
nicks2587 said:
hey guys while I was falshing my rom of xperia x10 via flashing tool follwed the procedures given after it completed and asked me to unplug the device and switch it on... now phone dos not boots and has got stuckd at sony ericsson logo...its not moving ahead... not even booting.. I ve tried to connect again in flashing tool flash mode still its not working .. phone automatically gets disconnected.. also wen I put the battery inside it turns on to sony ericsson logo automatically even if I dnt use power on button.. help me out... plz plz plz
Click to expand...
Click to collapse
Some of the custom roms are flashed with xrecovery or cwm,
Now what kind of rom did you want to flash?
Maybe you went wrong that in procedures said "flash the rom".
Put out the battery then put in and turn your device on then restore your previous rom then try again and install(flash) new rom.
Good luck.
Sent from my X10 using XDA
Merry Xmas and happy new year guys. can someone help me. i have xperia x10i. i have done rooting it and when i tried to unlock bootloader. my battery suddenly died at step "turn of phone, wait for 5scnd push back button, put on usb" i tried reconnect the fon but it wont connect. and the fon dont charge the battery. ive try charge the battery using xternal charger. it works. but the problem now is the fon can not turn on. and when i tried to do the step i have stuck before the option in flashtool plugin dont show the "unlock bootloader" option. how can i resurrect my fon just like before?i tried use SE companion tu repair fon but the SE companion said SE update engine dont have software available for my fon. please help.
Can you get the phone in flashmode?