Here's the deal folks...my mom washed her Vibrant in the washing machine a few days ago. 2nd Vibrant by the way. Anyways, pulled it out, threw it in some rice, got LOADS of water out of it and voila! Amazingly, after being through an ENTIRE wash and rinse cycle...it basically works! Everything...screen, cell radio...everything, except for the buttons. My question of course is why does everything else work except the capacitive buttons? They light up, but pressing them doesn't actually make anything happen. If anyone has been through this, please let me know what you did to fix it. Help a mod out anyone? THANKS!
Perhaps there is still a little moisture in there preventing it from reading the touch. Just a thought, haven't had to deal with this. *knocks on wood*
Edit: if thats all that doesn't work. I'm sure a replacement part would be relatively easy to install. Beats the price of a new phone...
Sent from my SGH-T959 using XDA App
Crack it open and look for any white mineral deposits that may be on the mainboard and clean them off. Of course let it thoroughly dry out again. I have used a toothbrush and alcohol to clean them in the past.
Sometimes that can help.... Good luck!
Open phone take out everything battery sim etc.
Now just turn it on its back and leave for a hour or so eventually if there is water it will drip out if you notice little bits of water on the thing you put your phone on then there's probably more water in and do the rice thing again. Can't give much more suggestions than that.
Sent from my SGH-T959 using XDA App
My T959 is dead
ashasaur said:
Here's the deal folks...my mom washed her Vibrant in the washing machine a few days ago. 2nd Vibrant by the way. Anyways, pulled it out, threw it in some rice, got LOADS of water out of it and voila! Amazingly, after being through an ENTIRE wash and rinse cycle...it basically works! Everything...screen, cell radio...everything, except for the buttons. My question of course is why does everything else work except the capacitive buttons? They light up, but pressing them doesn't actually make anything happen. If anyone has been through this, please let me know what you did to fix it. Help a mod out anyone? THANKS!
Click to expand...
Click to collapse
Wow...I always knew these vibrant phones are not easy when it comes to dying.
I have sorta a related story as well....
I'm in Canada right...and once when we had 15cm of snow amidst -20C or -4F, I needed to go shovel all the snow mess off the ground.
I had my T959 in my big ass jacket's pocket so its all nice and warm in there...but once I came back to the house, I noticed it was wet from all the sweating. Damn, that snow shoveling is a real hard workout for reals.
Anyhow, I opened my Vibrant up as per this guide on youtube http://www.youtube.com/watch?v=gOvt6atrin8
There's no traces of water and my buttons still will not work, they do light up but that's it.
I'm not into warranty, I love to get in and pull and push...play engineer sorta. Didn't work...now I might be looking into buying some spare parts.
Funny thing is the rest of the touch screen is still super responsive even when I'm out in minus weather...just these heat sensitive touch buttons grrr.
Related
So, about 2 weeks ago, I got my HD2 off of Craigslist with a cracked screen. It worked perfectly fine with the exception of the hardly noticeable cracks. I knew I could get the replacement digitizer/screen for $40-80. I got my screen in the mail yesterday and, following the "YouTube" video tutorial found on this site, I......ugh.... replaced the screen....................I SCREWED UP BIG TIME!
First, I broke the ribbon cable for the Side "Volume Up/Down" buttons. Then, I broke the ribbon cable for the "soft keys." Ah, crap, but oh well. I figured I could use the touch screen for pretty much everything i needed to do. Well, while prying the cracked digitizer screen from the LCD, I went a bit too deep & peeled the tinted film off of the LCD. I thought nothing of it at the time. I'd already done enough damage. So the display would be a bit brighter than normal oh well.......WRONG! I put the phone back together and once I get it to power up, all I get is a white screen. I thought I missed something. So I disassemble & check 3 more times. Still a white screen.
Well, after all of this, the new digitizer/screen doesn't want to stay in place very well. So, being pissed off and curious, I pull it out and away and notice in the backside reflection of the digitizer that I can slightly make out the phone display. So, apparently the "Tinted Film" that I accidentally peeled off of the LCD makes images visible on the phone screen. I kind of damaged this film when peeling it off. Therefore, I am unable to put it back on. Does anyone know of a simple fix without replacing the LCD?
SORRY FOR THE "SHORT STORY LONG."
I was brainstorming and thought that maybe the film was polarized. So, I grabbed my sunglasses, which are polarized, and wearing them, I can faintly see the display. Anyone think maybe polarized window tint might fix my problem?
Hey man I have some electronic devices that need repair, can I send them to you to fix them?
SURE!
You can pay me in HD2 parts.
Sir i can only say 1 thing. search ebay and replace everything you damaged. only that way you will get your hd2 in perfect state.
keesmathot said:
Sir i can only say 1 thing. search ebay and replace everything you damaged. only that way you will get your hd2 in perfect state.
Click to expand...
Click to collapse
I'd go one step further and say bin it and get a new one!
You sound just like me. That is why I never try things like that anymore. Hope it gets sorted but might be better looking for a used one.
I've got it functioning...
I found the film that I ripped off, put it over the screen and........I CAN SEE! However, the top half has lines through it. So, I must've damaged the LCD. The good news is that my phone is useable again. I just have to do everything via the touch screen and can't let the screen hibernate unless I have my charger close by. I'm just gonna keep my eye out for a cheap busted phone and eventually have a 100% phone again...
I sympathize with you. I broke HD2 while I was trying to check for loose WiFi card cable(cuz i was getting weak WiFi signals). The cable turned out to be fine but the external speaker stopped working. I opened it up again and adjusted some parts and it just got worse. the HD2 didn't power on at all. I tried fixing it but to no avail. I ended up sending the HD2 to a repair shop and was charged $170 for the repair. the repair guy said i messed up the power IC and the connector for the external speaker and he had to replace the power IC and resolder the connector.
I think I'm gonna stop trying to open up expensive phones. i was stupid thinking that since I have successfully replaced digitizer for my previous Palm T3, E2 and T5, opening up HD2 wouldn't be a problem. Should have known HD2 components are really fragile...
mmarkk said:
Hey man I have some electronic devices that need repair, can I send them to you to fix them?
Click to expand...
Click to collapse
made me laugh.......
The best topic ever Thanks, dude!
I've always read many people telling tales of their phones being ruined by being dropped in water and pretty much either having to do the rice bowl treatment for a week or giving their phone a tear jerking burial/insurance return. Well here's my tale:
While defrosting some zip lock bagged steaks in a kitchen sink full of water my Galaxy S II which was streaming Pandora at the time decided it either didn't want to sit on the counter with the seasoning or decided that it would be nice to go for a swim - actually it was probably the grocery bag being moved that knocked it into the sink - me not paying attention noticed the change in sound of the streaming music from clear to muffled looked for it then in disbelief saw the phone at the bottom of the water filled sink!!!!
I think my heart grew 10 times smaller as I thrust my hand into the sink pulling the phone out from under the depths of the water and zip locked frozen steaks, as I pulled it out from the water the music was still playing but sounded rather tinny so I frantically took a towel and wrapped it around the phone to get the water off of it then pushed the power button to see the screen light up to the lock screen. I then swiped the unlock screen and quickly closed pandora and frantically pressed the power button choosing the shutdown option dreading the worst that the phone was playing it's curtain call song and was about to die any second, then the screen went thru the shut down phase then the screen went blank and all of a sudden it turned back on and I saw the android mascot and some red and yellow text (perhaps I pushed the power button too long or the phone looked like it went into recovery mode?) and started doing "something". I said oh sh*t put the phone on the counter screen down and peeled off the back cover and yanked the battery.
at this moment I started examining the phone, the inside was completely dry sans a droplet of water over by where you pry off the back, no water on around or under the battery, around the camera or flash, the power or volume rocker, or any visible leakage around the screen. I then shook he phone over the towel I had initially dried the submerged phone with and did see a drop come from the speaker slits and then I put my mouth to both the usb and headphone jacks to suck water out of those openings (phone CPR?) and got a tiny drop maybe from the USB but nothing from the headphone jack.
At this point I was still in shock but very surprised that the phone was pretty stone dry sans from the water I wiped off of it and the tiny bit that was in the speaker opening. I gave everything a once over again with the towel just in case I missed some microscopic droplets and shook the phone again put the battery back in put the back back on and pressed the power button and voila, the Samsung Galaxy S II logo popped up and in no time the phone was back on and running like nothing happened - I ran a plethora of tests for the rest of the nigh dreading the worst but everything was golden with the exception that the speaker sounded a little tinnier that it initially was which pretty much cleared up buy the morning and sound as lout as it was out the box, I think that the water on the speaker had to dry.
Call me lucky but I've never never never experienced such amazement with a phone before in my life, it was as if the phone had a waterproof force field around it lol. I had initially though about taking the phone back to wait for the Galaxy Nexus on ATT but after that experience I'm totally on board with the Galaxy S II - I did get a tad paranoid that something might end up going wrong with the phone from the submerging to I took it back to the store last night to exchange it for another stating the speaker sounded tinny which they gladly did and after grueling task of reconfiguring all my settings and installing all my apps the new one is back as my main player and my Captivate is back in it's box (used it during my paranoid night of testing everything after the submerging).
Call me sold, I'll definately be keeping the wonder phone AKA Galaxy S II until the Galaxy S3 comes out , and I'll definitely be keeping it away from water, not gonna try my luck twice!!! Glad to see it's somewhat waterproof but please don't try this at home my heart could barely take it LOL!!!
Wow, I would panic if that happened to my brand new phone! Glad yours is still working
just tried this and it doesn't work
Next time (hopefully never) just leave it in a bag of rice for a while just in case instead of just powering it back on.
Coincidently, I came across this video today of the original Galaxy S:
http://www.youtube.com/watch?v=8puSOR2wWfQ
When I used to work for best buy repairing laptops at their GSC, I had a broken keyboard laptop come in. When I went to replace it, I found corrosion from head to toe all over the motherboard from some sort of spill. But everything on the laptop still worked (sans the KB, but it did after replacing). I tested the hell out of it, took pictures of the water damage, wrote it up for the customer. Some people just get lucky with water damage
mtnDUE said:
just tried this and it doesn't work
Click to expand...
Click to collapse
Lol
Sent from my SGH-I777 using xda premium
Glad you didn't wreck your phone dude, that would /could have been really horrible.
Cool, I'm gonna give it a try....... NOT!
Years ago (late 90's I believe) I had an Nokia 6130 that I dropped in a inch plus puddle in a parking lot as I ran into the store on a rainy day. I didn't notice it until I was returning to my car later. Had to be at least 10 minutes or more. I let it dry out over night and to my surprise it functioned. I don't remember but I think the battery may have come off when it hit the ground, either way it pretty impressive.
Sheesh.... I don't think I would've waited for it to shut down... I would have been yanking that battery out post-haste.
Congrats, you were a lucky one... I think you should go buy some lottery tickets tonight... Don't wait until tomorrow.
Don
Yeah I had though about the rice bowl treatment before turning it back on but since it was so unbelievably dry and water free I took the chance and turned it right back on, even plugged the sucker in to charge it back to 100% leaving it on the charger all night with no issues at all the next day. I should have kept it as a good luck charm but didn't want to press my luck and have something go awry later so since it was still working with no issues I took it back the following night to exchange for a new one - just in case.
Let's see a metal phone take such abuse LOL, like it or not Samsung knows what they are going making their phones out of lightweight yet solid feeling plastic components, survive drops, scratch resistant screen and now add to the list moderately waterproof - it takes a licking and keeps on ticking! I summarize it down to the plastic, plastic expands as it gets warm which probably made a more watertight seal than when turned off, flimsy back my foot - I doubt a phone like the Inspire would have survived that dunking without catastrophic results.
As Fragile as it seems the Galaxy S II is pretty safe to carry around naked and survive most elements, and that's how I'll continue to carry it - while making sure to avoid water like the plague!!!
phones are weird when it comes to water, I had an iPhone 3G that sat in 3 feet of lake water for a good bit -- it still works to this day -- it had the same tinny sounding speakers for awhile and occasionally an incoming call would have really odd ring sound... when that happened i would have to hang up and call back -- but rarely happened.
Glad to know the SGS2 is potentially [moderately] safe against water exposure
I have lost a few family members to water, but not my phone!
Glad to hear I might have a chance when dropping this bad-boy into my sink.
cwc3 said:
I have lost a few family members to water, but not my phone!
Glad to hear I might have a chance when dropping this bad-boy into my sink.
Click to expand...
Click to collapse
would probably survive a drop into the toilet or a bath as well, LOL, just some of the experiences I've read on the net but know a lot of people use their phones around these water hazards as well LOL .
So it happened this morning when my alarm went off and it vibrated. I heard a plastic part vibrating also. The sharp loud noise was disgusting. I shut off my alarm thikning it was my cheap SGP case.
Later today I played around trying to find out if the silicone had a hole or something where the plastic frame was touching the SGS2 phone itself. Nope. I took the whole case off. Each time it vibrates it sounds like... ahh what the hell. I will film it for you guys now.
http://www.youtube.com/watch?v=_GoIrBmMC1U
WTF is that? I took the cover off. I took the SIM card out on another occasion too. It sounds like something on the upper left. If I push my finger down on the panel, it stops. If you notice the few seconds it is sitting on the table flat, it's fine. Just a little weight seems to calm it down. Not sure if its the vibrating motor itself because it is vibrating properly. Sounds like something is loose inside though...
Anyone experienced this before? Should I go for RMA?
Second part of the question:
Obviously being an XDA-er I'm rooted. I will flash back to stock and unroot. I bought this off of Expansys-USA so I should get *some* reasonable attempt by them to send it back. What are the chances that my warranty gets denied? I don't have a USB jig to reset the counter, but I'll of course get rid of the yellow triangle.
*grrrr... I need to dig up my Nexus S now if I have to go through warranty... I'm guessing I'll be phoneless for weeks*
I don't know if it would invalidate the warrenty or not (technically rooting/custom roms is supposed to), but when I had a problem with my stereo jack not working rather than risking it I just replaced the part myself.
The vibration motor, stereo jack and earphone speaker are all on the same part.
(I got it from this guy on ebay for about $7 if you're curious.)
Random6 said:
I don't know if it would invalidate the warrenty or not (technically rooting/custom roms is supposed to), but when I had a problem with my stereo jack not working rather than risking it I just replaced the part myself.
The vibration motor, stereo jack and call speaker are all on the same part.
(I got it from this guy on ebay for about $7 if you're curious.)
Click to expand...
Click to collapse
I see. I'm not sure whats broken really. When I shake my SGS2 I hear something rattling inside. I'm just afraid to open the thing up... is it difficult?
Just watched your video. It sort of sounds as if somehow the vibration motor came loose from its proper spot and is now moving around vibrating against the plastic. Its normally held in with some adhesive (basically double sided tape) within a cutout area.
When I had mine apart I actually took a photo, http://i.imgur.com/fgN9F.jpg, if that makes it any more clear.
I actually recorded the process of me reinstalling the new part (excluding the disassembly, there are lots of clips of that from other people on youtube) but havent gotten around to uploading it yet since my internet connection sucks and the file is nearly 2GB.
Edit to add:
No it wasn't really all that difficult to dissassemble, it was actually pretty easy. That said I enjoy taking things apart and trying to fix them. This was the first time I've dissassembled anything as small as a cell phone, but I'm used to taking things apart and trying to fix them when they break. If you don't have any experience taking apart electronics you might want to think twice or just pay someone who fix's cell phones to do it.
If you're thinking about it, heres a video where someone shows taking it apart to get a rough idea of whats involved.
http://www.youtube.com/watch?v=QKztg1ra4-0
I decided to try and upload the video I took, once it finishes (in about 2.5 hours) it should be viewable here:
www.youtube.com/watch?v=-ud1upGzLBs
Random6 said:
I decided to try and upload the video I took, once it finishes (in about 2.5 hours) it should be viewable here:
www.youtube.com/watch?v=-ud1upGzLBs
Click to expand...
Click to collapse
thank you for your detailed writeup. im going to try this. ive taken apart my macbook pro to install an SSD before, and a few other electronics, but i'm not the very best (i feel clumsy sometimes), but i'm willing to give this a shot.
The only thing I'm worried about is that I could potentially mess up the phone in other ways in disassembly such that my warranty won't be honored if I need to resort to that... We'll see tonight. It looks like you used two screwdrivers? Which ones will I need? I have a #000 that I see will be needed for the back plate at least...
k. opened my phone up.
i just took the screws out and the backplate. i pushd around to make sure things are tight, and they seem to be.
put it together and the vibrate thing happens VERY rarely now..
I shook my phone around and still heard something shaking (please tell me if this happens).
I opened up my phone and the camera module seems to be loose. Is it supposed to be glued down?
Just to let you know, you say you don't have a USB jig so your Flash counter may make your warranty void, but, if you flash to an ice cream sandwich ROM (Cyanogenmod 9) you can install an app called 'Triangle Away' which will basically get rid of the Flash count and yellow triangle - it needs root by the way. (search it up on XDA, it's by chainfire')
Then you can flash stock and send in for warranty.
Sent from my GT-I9100 using XDA
dmo580 said:
k. opened my phone up.
I shook my phone around and still heard something shaking (please tell me if this happens).
I opened up my phone and the camera module seems to be loose. Is it supposed to be glued down?
Click to expand...
Click to collapse
I don't remember it being glued down. Its been a few month since I fixed mine but if I recall correctly it just fit snugly in place between some plastic fitted walls.
This is the camera module you mean right?
Edit: I also don't hear anything shaking with mine, did you mabe leave a screw loose inside?
Random6 said:
I don't remember it being glued down. Its been a few month since I fixed mine but if I recall correctly it just fit snugly in place between some plastic fitted walls.
This is the camera module you mean right?
Edit: I also don't hear anything shaking with mine, did you mabe leave a screw loose inside?
Click to expand...
Click to collapse
Yeah. Camera module. That's the one. The main 8MP shooter. It's not glued down or anything. It shakes around inside. I definitely did not leave a screw inside because I only opened the back panel and I put all the screws back in.
It's weird because something making noise while shaking the phone has been documented here:
http://forum.xda-developers.com/showthread.php?t=1254520
And I noticed that when you activate camera it goes away. Quite strange but as an engineer this makes me wonder HOW that even happens? Shrug.
I'm waiting for my Samsung Focus S phone to come from the Windows Phone challenge and I'm contemplating using that for a month while my i9100 goes out for warranty. Of course I can always use my Nexus S as a backup, but part of me wants to force myself on a new platform for a month and see how that goes... Hahahaha.
Random6 said:
No it wasn't really all that difficult to dissassemble, it was actually pretty easy.
Click to expand...
Click to collapse
Hey Random6, did you happen to find that after replacing the vibrator motor with a new one, the intensity is now less than when new? I used double sided tape, but with 1.5mm, I guess the motor won't vibrate AT ALL.
Also I found that if I don't screw the one that seems to be closest to the vibrator motor all the way in, it obviously vibrates harder, but not hard enough.
I also used two very thin copper plates to sandwich the motor between the plastic plates, but once again, that was too much and the vibrations were not transfered to the phone's body, but I could hear it doing its job.
Any suggestions?
Thanks!
I was so happy with my Note. Great battery life, fast response, minimal/no black crush... and then something caught my eye when I loaded up the Google Play app. For a split second while the background was changing, I noticed the faint imprint of the "Texting and driving it can wait" sticker that comes affixed to the phone when I first bought it. I thought I was seeing things.
Then I loaded up the S-Memo app where it has a tan background and is easy to see screen damage. I deleted my s-memos to get a clear picture of the screen, and sure enough I clearly see the entire imprint of the sticker that comes affixed to the phone. I tried cleaning it, rubbing it, yelling at it, and nothing made it go away, It's permanent. I don't even drive!
What the hell?! Has anyone else noticed this? Try it -- go into your S-memo app and delete enough of your picture memos so the tan background is showing. Anyone else have screen damage?
I apologize for the tone of my first post -- this is already my first replacement Note as the first had a dead/hot pixel cluster that was instantly visible upon powering up the phone.
Off to Best Buy tomorrow to get a replacement.
Edited to include a photo of the issue.
Wow just checked mine and its not there go return it thats beat
Sent from my SAMSUNG-SGH-I717 using XDA Premium App
No inprint here.
Easy solution to this though, just take it back and get a new one. At least I hope it didnt take you more than 30 days to notice this.
im sorry.. that is HILARIOUS
you can get a new one though. do it up man. this phone is GREAT.
Lol.
Sent via tapatalk using the Samsung Galaxy Note
How does that even happen?
It's not residue on the screen is it?
Guess they were trying to get there point across lol. I would try Goo Gone before returning it.
Goo gone is sone amazing stuff, but I personally try to not use chemicals on any electronics anymore... too many companies are using exotic films on the glass these days. If your return wont be that hard, i'd just do that.
Sent from my SAMSUNG-SGH-I717 using XDA
wtf? How would that even happen? It's just a vinyl sticker!
Naw man, that's whack - go exchange it. I can't even imagine what that phone went through to get a permanent imprint from the sticker on it.
Er.... have you removed the sticker..???
Sent from my SAMSUNG-SGH-I717 using XDA
You know your note is a really Smart phone if its trying to tell you something. On a serious note, hope you got an exchange from BB.
-Once you go NOTE, you'd say 4 inches a Joke
How could this possibly happen? Because it's not like it's stencil letters, it comes on one vinyl strip
Only way I could see this happening is if you left the sticker on and set it outside in the sun for days
Exchange it!
Or try Mr. Clean's Magic Eraser
I would just replace it. Using any form of chemical or magic eraser could potentially cause damage, which could void your warranty. My experience with Best Buy exchanges, they are really good about it, as long as there is no damage to the device. It's not worth the risk. It sucks that this happned to you, but you have to admit, of all the possible flaws on a phone, you got the king of them all.
Sent from my Galaxy Note (SGH-i717) using XDA Premium.
After seeing this thread I had to check mine (doesn't appear on mine).. That is one freakish issue and definitely should be exchanged.
Keep us informed on how you make out.
No way would I even attempt to clean it, just return it.
To answer some questions: Yes, I took the sticker off, but only after using it with it on for a couple days until my screen protector arrived. I was very careful about using it and, this may not show in the picture, but the ENTIRE protector is imprinted on the screen INCLUDING the border.
I truly have no idea what caused this, my only guess is a manufacturing defect. Off to Best Buy now. I'll report back with my non-cursed Note *knocks on wood*
Also, thanks to you all for the many lulz this thread has provided me in my "fist-world sorrow."
Dude!
demigodchewtoy said:
To answer some questions: Yes, I took the sticker off, but only after using it with it on for a couple days until my screen protector arrived. I was very careful about using it and, this may not show in the picture, but the ENTIRE protector is imprinted on the screen INCLUDING the border.
I truly have no idea what caused this, my only guess is a manufacturing defect. Off to Best Buy now. I'll report back with my non-cursed Note *knocks on wood*
Also, thanks to you all for the many lulz this thread has provided me in my "fist-world sorrow."
Click to expand...
Click to collapse
You're joking right? You used the phone with it on there for a couple of days and are wondering why the image is burned into your phone?? Even going as far as saying your not is cursed?
My guess: You left the TXT & Drive sticker on there while using it, and the heat generated from the phone on the screen made it rub off. (like iron on graphics on a shirt). To make it worse, you put a screen protector on it further locking in the imprint for several more uses.
Mystery solved?
Hey guys. I recently had to walk in the rain for about 30-40 minutes to my Dads work, and no I don't have a car at the moment. My phone had closed flaps and everything when I was walking. I had my rain jacket on but my phone was in my jacket's pocket. When I arrived at my dad's work I saw how wet my phone was, so i dried it off with a towel. First thing i tried was listening to music using my earphones, and it didn't work, so maybe i though it was my earphones. Then I tried to watch an MKBHD video (Yes, why not.) on youtube in landscape mode, but it didn't work, so I tried playing a tilt racing game, and my car didn't turn at all. So up to that point, i got stressed out. So I rebooted my phone, and first thing I noticed was that my Notitfication panel was Stock Marshmallow and not N themed anynmore. Then approx 7 seconds later, BOOM. Everything on screen went gone. Since it wasn't an amoled screen, i could still see that the backlight was still on, with slight darker areas around the bottom right corner. The touchscreen was still working. I was able to boot into the 'invisible recovery' (lol) and I could swipe and press and do everything, but still nothing on-screen was showing. The I looked at both of my cameras, and I could see on moth there was waterdroplets around the lenses. At that point, I got extremely stressed out, but i still ate pizza because i was hungry. (lol) So I putted in rice when i got home overnight. Still nothing happened. When rubbing the power button, i can feel water sliding out gently. I couldn't understand up to that point. "The Z2 is waterproof! Water damage was the last thing on my mind to happen to this phone!" Any solutions or tips from you guys? Thanks alot for any help!
And please don't comment that I'm a troll and i deserve it, because I'm not! Anyway, I just need help on this. Thanks!
Put it back in rice and leave for a lot longer on a radiator. Leave flaps open. Whenever phones act up after being in contact with water you gotta power that thing off. I know to late but keep drying that phone off. Best you can do. I had some say they did it for week. This worries me for my phone. But the phone really isn't that waterproof. This flaps can fail with just a little dust trapped in them..
Sent from my D6503 using XDA-Developers mobile app
z2_flaps
Hej as I wrote in PM to Brandon, last year I send my phone to service couple of months old z2 for faulty pixels and themselves replaced casing, flaps, and also some parts of screen. They only commented that casing with flaps was faulty. Precaution with water... Then saying that I submerged it in swimming pool for coupe of minutes and shot a great video, phone still works.