I have a sony erricsson xperia x10a and I am having a problem with it. It is loading up but then shutting up and trying to load again, pretty much looping at the boot stage. someone suggested I reinstall update 2.1, how can i update it again or is there any other way to do it.
Thank you.
Here you can reflash to 2.1 http://forum.xda-developers.com/showthread.php?t=825675
alda.audisho said:
I have a sony erricsson xperia x10a and I am having a problem with it. It is loading up but then shutting up and trying to load again, pretty much looping at the boot stage. someone suggested I reinstall update 2.1, how can i update it again or is there any other way to do it.
Thank you.
Click to expand...
Click to collapse
Take battery out hold back key put battery in, leave usb cable attached. This will put it back in flash mode, then you can update
This forum is for development. please keep it clean
Related
I can't turn on my X10.When i press the on button,it's only vibrate a bit then nothing happen.No light is on even when i plug in.More over,when i plug in the press the on button,it won't even vibrate like without cable.
Please help me
Have you tried to re-flash it with the 2.1 or 1.6 FW with Bin4ry's flasher?
Which device do you have? A generic one or developer phone?
i'm having the generic one and i just update it to 2.1 this monday.
It won't seem to have any power goes in when i plug in.How i'm going to reflash it anyway? please help me
shinnie88 said:
How i'm going to reflash it anyway? please help me
Click to expand...
Click to collapse
Did you use a 2.1 from this site? If so, take out your battery for 10 seconds, then put it back in just before you attempt to reflash.
Thank you so much.My fone turned on again.By the way,should i change back to global generic or just leave it as nordic?
shinnie88 said:
Thank you so much.My fone turned on again.By the way,should i change back to global generic or just leave it as nordic?
Click to expand...
Click to collapse
Nice 1. It's totally up to you, I've stuck with the Nordic for now.
My phone went off again.This times also can't turn on or charge.But when i hit the on button,itz flash red 3x then went off.Anyone know what happen? please help me
X10 only vibrate
Same problem here X10 only vibrates,
i tried flashing bin4ry way it stops at around 75%
Tried even in sonyericsson update service but still no luck
It also stops around 25%, my phone is generic & my battery
Is fully charged any ideas?
Pls help
I have the same problem if I flash a firmware using FlashTool. I am stuck at 1.6 and I can't install any other firmware because I can't turn it on. Only firmware that works is the one from ROOT_F3V3 but it is a 1.6 firmware
If you find a firmware that works please post it.
Try downloading the latest Flashtool and then flash the latest firmware available; http://forum.xda-developers.com/showthread.php?t=936733
Its happened before. The phone will not boot, I waited several hours and ... it was working again, but I do not know why
Try to connect into flash mode and install SE original ?
Ok, i had to do this twice now, as i bricked it a couple of weeks ago
you'll have to reflash with sony ericsson update service here:
http://www.sonyericsson.com/cws/sup.../detailed/updateservice/xperiax10?cc=gb&lc=en
Follow the instructions and press the back button before plugging in the cable.
Download the software and keep in mind that playing around with roms will result in these problems so don't go too far.
1. Take your battery out.
2. Hold the back button. Make SEUS running and ready.
3. Plug it into the computer.
4. Put your bateery back in.
Follow the instructions. Hopefully it would work and good luck
If it worked dont forget to hit thanks button.
Sent from my X10i using XDA Premium App
ty so much JingleJo, your method worked for me
XperienceD said:
Did you use a 2.1 from this site? If so, take out your battery for 10 seconds, then put it back in just before you attempt to reflash.
Click to expand...
Click to collapse
Man plzz help me i'm a noob in this things i have the same problem with that guy but i dont know how to reflash my phone :S where can i take the 2.1 :S i dont know nothing :S:S
---------- Post added at 10:26 AM ---------- Previous post was at 10:20 AM ----------
XperienceD said:
Did you use a 2.1 from this site? If so, take out your battery for 10 seconds, then put it back in just before you attempt to reflash.
Click to expand...
Click to collapse
Plzz help me i have the same problem :S but i dont know how to reflash my x10 :S i dont know where can i take the 2.1 plzz can u tell me with a video or with steep :$ like baby plzz
My xperia arc went dead after trying to upload OTA update, yeah i know i shouldn't have but i guess it too late now. however i will like any help as to how to revive my phone. the charging light even don't turn up.
Pls anyone, I'm desperate
PS:the phone was unlocked
download the generic 2.1 firmware and save as in flashtool/firmwares.
Put yout phone in flashmode and flash back to 2.1....
Sent from my SO-01C using xda premium
Pc companion to 2.3 then do ur thing..like modding and stuff
Sent from my SO-01C using xda premium
currently running 2.1
completley idiotic mistake i replaced all my system apps to there defaults again without changing file permission ....
I understand you do not have xrecovery installed. Reflash phone
ok i have no idea to do that considering i can't get my fone off... it's stuck in the loop cheers for that well thought out answer that gave no help at all
Take out the battery, put it back in and don't turn it on.
Use Sony Ericsson PC Companion and follow the onscreen instructions to restore your phone.
Also, YOU are the one with the problem, so if someone tries to help you don't be rude please.
Have tied to remove your batt?
hey guys think i have it fixed via update service thanks anyways
Glitch83 said:
Take out the battery, put it back in and don't turn it on.
Use Sony Ericsson PC Companion and follow the onscreen instructions to restore your phone.
Also, YOU are the one with the problem, so if someone tries to help you don't be rude please.
Click to expand...
Click to collapse
Thanks for your answer, i had not seen it when posted mine. Finally seems our friend to have solved his problem reflshing,,,, jejejejeje.
I was reboot my phone and once he do this:
Screen out (duh) screen on with ''Sony Ericsson'' then he still stay
on that, idk dont know why.
I have reinsert my battery i have used the right and left button`s.....
So, if someone can help me with a other option, please help me...
Very Thanks alot!!!...
x10i-user said:
I was reboot my phone and once he do this:
Screen out (duh) screen on with ''Sony Ericsson'' then he still stay
on that, idk dont know why.
I have reinsert my battery i have used the right and left button`s.....
So, if someone can help me with a other option, please help me...
Very Thanks alot!!!...
Click to expand...
Click to collapse
try using flashtool. directions are in the link.
U mentioned you have a x10i correct, then pick the firmware you want with the x10i with the latest baseband. if you still have questions, keep asking.
rooting is next if you go that route then, flashing ROMS, which are associated with a baseband
here is the link for flashtool: http://forum.xda-developers.com/showthread.php?t=920746
Yeah dude, use flashtool.... just flash it back... tht worked for me... i bricked my phone once.... now its rollin again....
how long did you leave it on the SE screen for?? sometimes mine takes a minute to boot through that?
im_iceman said:
how long did you leave it on the SE screen for?? sometimes mine takes a minute to boot through that?
Click to expand...
Click to collapse
ummmmh, more then 24 hours... :S
but i gonna try Flashtool right now, i hope i will work.
you could also just repair it using SEUS... depends if you want to root and install custom ROM's etc..
im_iceman said:
you could also just repair it using SEUS... depends if you want to root and install custom ROM's etc..
Click to expand...
Click to collapse
ok, i`ll try...
i can`t place my phone in Flashmode he gonna automatic to the Sony Ericsson logo...
What did i wrong?...
fire up SEUS, get to the bit where it say to connect your phone.
take the battery out for 10 seconds or so..
plug the micro USB cable into your phone only..
hold the back key (and keep it held until SEUS tells you to release it later in the process), push the battery back in
push the USB cable into your PC.
Should boot up into flash mode and SEUS will do it's thing!.
Done it before
Hi mate done it today since im new at rooting if you were trying to install a theme or rom, you might not have their firmware, if this is the case then you just from that Sony Ericsson screen keep pushing the Back or <-- key, this will boot you into xrecovery and just restore... if you havent made a back up, then you could try replace the rom you have back with the Se offical 2.1 rom which you can find in Android dev. and just launch it back with that... Hope this worked!!
hi guys. my x10 froze at se boot and does nothing. i've read through almost all helpfull threads that are similar to my problem but the problem still persist. fyi, i booted to xrecovery, made a backup and i noticed that there were problems in backing up (md5 chcksum, i think). but the backup file was created. i restored using that file and now it is stuck at boot. i can't even turn the phone off. i've tried hard reset, tried using the sues, flashtoo and even pc tools but to no avail. this is due to the phone can't connect to usb. can anyone please help me.
You have do a factory reset and wipe cache?
how can i do that andres3d? are there any way for me to do that? i'm trying but the phone just can't go past the se boot. it's just stuck there. i can't even turn the phone off. the only way is to take out the battery.
Try this, enter into xrecovery and select "factory resect" first at all, then reboot.
I got stuck there too, and I haven't the xRec installed
You can download the SE Update Service (SEUS) and flash the original rom back to it.
Download the software and install, take off the battery, wait a little bit (30s or so), insert the battery back. DO NOT TURN ON THE PHONE YET.
Open the SEUS, choose the phone (X10) and click 'go', or 'ok', or whatever. Keep going and the software will tell you to plug the phone. Plug the phone turned off. When it's plugged, turn it on holding the back button until the software tells you to release.
Wait a few moments... and it's done. Turn on your phone, it should take a little longer to boot, but it's just the first time, then it boots normally.
It's quite easy to do when you know what to do
thanks in advance but i've tried both method and it still got me nowhere. first, i can't boot to xrecovery at all and second, the sues doesn't even detect my phone.
Did you try download a stock firmware from here and install by flashtool?
Do you have installed drivers from x10 to your PC?
I thing the only way is by flashtool, because you don't have xrecovery access l.
http://forum.xda-developers.com/showthread.php?t=872298
Sent from my X10 using XDA App
rota2903 said:
thanks in advance but i've tried both method and it still got me nowhere. first, i can't boot to xrecovery at all and second, the sues doesn't even detect my phone.
Click to expand...
Click to collapse
Your phone must be charged ¬¬
Leave him charging at wall for about 45-60min and then try to do the step-by-step
tnx
tnx guys. i'll try the methods that u guys suggested. i really hope that i don't have to send the phone back to the shop.
OMG. it was actually my cable!!! that's why i can't flash my phone. now the phone is back to it's original state. anyways, i would like to thank all of you guys that have given me great advice. thanks again guys.
[Q] {HELP} another x10 stuck at se boot part 2
rota2903 said:
OMG. it was actually my cable!!! that's why i can't flash my phone. now the phone is back to it's original state. anyways, i would like to thank all of you guys that have given me great advice. thanks again guys.
Click to expand...
Click to collapse
Hi all
Unfortunetly my case is 99% similiar as "Sony Ericsson XPERIA X10XPERIA X10 Q&A[Q] {HELP} another x10 stuck at se boot" but changing the cables doesn't help. The only thing which the phone respond is to hold back starting of booting what immidietly happening when i'm connecting the usb cable.
I had xrecover installed before but is not starting onto flashing mode.
Any ideas
I may have posted in the wrong section and before you say there are topics covering this ive tried everything and im at my wits end!
I had a custom 2.2 ROM loaded on my Xperia for months but due to battery life issues i decided to upgrade to 2.3 (Wolf's) without doing much research.. Had i learnt that i needed to upgrade xRecovery to the latest release i wouldnt be in this dilemma.
I did the usual stuff when loading a new ROM but when loading the 2.3.3 ROM it failed.
Now when the phone starts up i get nothing but the SE logo!
Ive tried reflashing.
Ive tried using SEUS/PCC to update my phone - Which to no avail will the program recognize my phone for longer than 10 seconds.
Ive also tried SeTool2 and cant get my head around that.
If anyone has a fast easy fix for an idiot like me please point me in the right direction!
Should also add that i cant access xRecovery.
I am not trying to highjack this post but i am in the same position my phone is stuck in a loop on the black screen with the se logo.Flash tool or the se update service "sees" it for about 10 seconds not long enough to do anything.Please can anybody help?
A quick update i have sorted it i left it on se update and some how it went in to repair mode and i now have a working x10 again.The se repair didnt seem to be doing anything it just said please wait but i switched it on and it worked now i have to root it again lol
I think you should flash stock ROM 2.1 via flashtool, root and flash Xcr. Afterwards, you can follow the WOLF's instructions to flast TW ROM. Remember flash baseband .71
So i tried those things and still havn't gotten anywhere!
I cant flash the only thing i can do with flashtool is change the baseband and thats not very helpful to me atm!
I just wish there was an easy fix but apparently there isnt
Sohrix said:
I may have posted in the wrong section and before you say there are topics covering this ive tried everything and im at my wits end!
I had a custom 2.2 ROM loaded on my Xperia for months but due to battery life issues i decided to upgrade to 2.3 (Wolf's) without doing much research.. Had i learnt that i needed to upgrade xRecovery to the latest release i wouldnt be in this dilemma.
I did the usual stuff when loading a new ROM but when loading the 2.3.3 ROM it failed.
Now when the phone starts up i get nothing but the SE logo!
Ive tried reflashing.
Ive tried using SEUS/PCC to update my phone - Which to no avail will the program recognize my phone for longer than 10 seconds.
Ive also tried SeTool2 and cant get my head around that.
If anyone has a fast easy fix for an idiot like me please point me in the right direction!
Click to expand...
Click to collapse
Have u tried reinstalling stock 2.3.3 through flashtools.
Sent from my X10i using xda premium
Check this http://forum.xda-developers.com/showthread.php?t=928210
Sent from my X10i using xda premium
Sohrix said:
So i tried those things and still havn't gotten anywhere!
I cant flash the only thing i can do with flashtool is change the baseband and thats not very helpful to me atm!
I just wish there was an easy fix but apparently there isnt
Click to expand...
Click to collapse
Read Wolf's thread!!!
You HAVE to change the baseband, otherwise it won't work! You need baseband .71, which is included in the flashtool package he says to use...
mollydog said:
A quick update i have sorted it i left it on se update and some how it went in to repair mode and i now have a working x10 again.The se repair didnt seem to be doing anything it just said please wait but i switched it on and it worked now i have to root it again lol
Click to expand...
Click to collapse
How you did se update? My PCC see the phone and asks to "drag the status ber downwards" etc which i obviously cant do with just SONY ERICSSON logo on the screen...
chouck said:
How you did se update? My PCC see the phone and asks to "drag the status ber downwards" etc which i obviously cant do with just SONY ERICSSON logo on the screen...
Click to expand...
Click to collapse
If u have solved it how did u I fac esame problem as u?
Guys.. try this.. maybe you doing it at the wrong way.. i tried this on my x10 and it work.. http://www.youtube.com/watch?v=i6CMmZ62G3s&feature=youtube_gdata_player
First of all sorry for not replying sooner as i have been very busy, i have to agree with hr7 i used the Sony Ericsson PC Companion and clicked on repair