hi guys. my x10 froze at se boot and does nothing. i've read through almost all helpfull threads that are similar to my problem but the problem still persist. fyi, i booted to xrecovery, made a backup and i noticed that there were problems in backing up (md5 chcksum, i think). but the backup file was created. i restored using that file and now it is stuck at boot. i can't even turn the phone off. i've tried hard reset, tried using the sues, flashtoo and even pc tools but to no avail. this is due to the phone can't connect to usb. can anyone please help me.
You have do a factory reset and wipe cache?
how can i do that andres3d? are there any way for me to do that? i'm trying but the phone just can't go past the se boot. it's just stuck there. i can't even turn the phone off. the only way is to take out the battery.
Try this, enter into xrecovery and select "factory resect" first at all, then reboot.
I got stuck there too, and I haven't the xRec installed
You can download the SE Update Service (SEUS) and flash the original rom back to it.
Download the software and install, take off the battery, wait a little bit (30s or so), insert the battery back. DO NOT TURN ON THE PHONE YET.
Open the SEUS, choose the phone (X10) and click 'go', or 'ok', or whatever. Keep going and the software will tell you to plug the phone. Plug the phone turned off. When it's plugged, turn it on holding the back button until the software tells you to release.
Wait a few moments... and it's done. Turn on your phone, it should take a little longer to boot, but it's just the first time, then it boots normally.
It's quite easy to do when you know what to do
thanks in advance but i've tried both method and it still got me nowhere. first, i can't boot to xrecovery at all and second, the sues doesn't even detect my phone.
Did you try download a stock firmware from here and install by flashtool?
Do you have installed drivers from x10 to your PC?
I thing the only way is by flashtool, because you don't have xrecovery access l.
http://forum.xda-developers.com/showthread.php?t=872298
Sent from my X10 using XDA App
rota2903 said:
thanks in advance but i've tried both method and it still got me nowhere. first, i can't boot to xrecovery at all and second, the sues doesn't even detect my phone.
Click to expand...
Click to collapse
Your phone must be charged ¬¬
Leave him charging at wall for about 45-60min and then try to do the step-by-step
tnx
tnx guys. i'll try the methods that u guys suggested. i really hope that i don't have to send the phone back to the shop.
OMG. it was actually my cable!!! that's why i can't flash my phone. now the phone is back to it's original state. anyways, i would like to thank all of you guys that have given me great advice. thanks again guys.
[Q] {HELP} another x10 stuck at se boot part 2
rota2903 said:
OMG. it was actually my cable!!! that's why i can't flash my phone. now the phone is back to it's original state. anyways, i would like to thank all of you guys that have given me great advice. thanks again guys.
Click to expand...
Click to collapse
Hi all
Unfortunetly my case is 99% similiar as "Sony Ericsson XPERIA X10XPERIA X10 Q&A[Q] {HELP} another x10 stuck at se boot" but changing the cables doesn't help. The only thing which the phone respond is to hold back starting of booting what immidietly happening when i'm connecting the usb cable.
I had xrecover installed before but is not starting onto flashing mode.
Any ideas
Related
I tried -everything- found, to try and get to boot into xrecovery. I saw someone fixing it by reinstalling, and first deleting xrecovery within /local/tmp/ so I did that. At the second I deleted the xrecovery folder with RootExplorer phone crashed. Now it's permanentely stuck at Sony Ericsson-logo screen.
PC Suit offers no help since I can't boot the phone it claims it's not connected.
I downloaded "Omnius for SE" but I don't understand it's usage, since I don't have backup of my phone..
Can anyone help me out please, I'm scared
try to get your phone working again with SEUS (Sony Ericsson Update Service), you can download it from the SE site.
I'm an android-newbie, but afaik you will loose your personal data.
Thanks! I will try that out today at work. Will post how it's going
it is working methot i have used it for my x10 mini pro
windausiuxxp said:
it is working methot i have used it for my x10 mini pro
Click to expand...
Click to collapse
i have the same problem.i try the update and nothing happen.
serch in google seus do not use that from original sony ericsson. page
that happened with me
i used the flash tool and its back to life
you should time accurately rebooting, holding the back bottom and connecting
you'll get it after a couple of tries
goodluck
Thanks! It did wonders for me, back on track now!
Sent from my U20i using XDA App
when I used SEUS after bricking my phone it rebooted constantly without allowing me to break in^^ my solution to this was disconnecting the battery (which actually is pretty easy) then I could make another reflash with SEUS, and then I had a working phone
I was reboot my phone and once he do this:
Screen out (duh) screen on with ''Sony Ericsson'' then he still stay
on that, idk dont know why.
I have reinsert my battery i have used the right and left button`s.....
So, if someone can help me with a other option, please help me...
Very Thanks alot!!!...
x10i-user said:
I was reboot my phone and once he do this:
Screen out (duh) screen on with ''Sony Ericsson'' then he still stay
on that, idk dont know why.
I have reinsert my battery i have used the right and left button`s.....
So, if someone can help me with a other option, please help me...
Very Thanks alot!!!...
Click to expand...
Click to collapse
try using flashtool. directions are in the link.
U mentioned you have a x10i correct, then pick the firmware you want with the x10i with the latest baseband. if you still have questions, keep asking.
rooting is next if you go that route then, flashing ROMS, which are associated with a baseband
here is the link for flashtool: http://forum.xda-developers.com/showthread.php?t=920746
Yeah dude, use flashtool.... just flash it back... tht worked for me... i bricked my phone once.... now its rollin again....
how long did you leave it on the SE screen for?? sometimes mine takes a minute to boot through that?
im_iceman said:
how long did you leave it on the SE screen for?? sometimes mine takes a minute to boot through that?
Click to expand...
Click to collapse
ummmmh, more then 24 hours... :S
but i gonna try Flashtool right now, i hope i will work.
you could also just repair it using SEUS... depends if you want to root and install custom ROM's etc..
im_iceman said:
you could also just repair it using SEUS... depends if you want to root and install custom ROM's etc..
Click to expand...
Click to collapse
ok, i`ll try...
i can`t place my phone in Flashmode he gonna automatic to the Sony Ericsson logo...
What did i wrong?...
fire up SEUS, get to the bit where it say to connect your phone.
take the battery out for 10 seconds or so..
plug the micro USB cable into your phone only..
hold the back key (and keep it held until SEUS tells you to release it later in the process), push the battery back in
push the USB cable into your PC.
Should boot up into flash mode and SEUS will do it's thing!.
Done it before
Hi mate done it today since im new at rooting if you were trying to install a theme or rom, you might not have their firmware, if this is the case then you just from that Sony Ericsson screen keep pushing the Back or <-- key, this will boot you into xrecovery and just restore... if you havent made a back up, then you could try replace the rom you have back with the Se offical 2.1 rom which you can find in Android dev. and just launch it back with that... Hope this worked!!
Hey guys
So, i decided to try and root my phone and i think i cleverly chose to use a really old method and subsequently my phone is now pretty much bricked. It used to be software V2.1
now, whenever i turn it on (I need to take out the battery and put it back in to restart it) It goes to the sony ericsson splash screen, then a "MTT Docomo" screen and then the screen turns blank and stays like that. I got halfway through a guide i found somewhere on the internet and now this is happening D=
I can't repair it in the sony ericsson pc suite (it detects a phone but asks me to connect it etc. which i can't do).
I've read a bit around and i think the answer is using flashtools? Can i still do that when my phone's in this state? Sorry if this is a common question, couldn't find any similar cases though =S I'm not completely sure what to do... any suggestions?
Thanks!
yes, you're right, my opinion is you must have to flash your phone properly with a clean stock rom before retry to flashing your phone another time.
And to make it properly is to use flashtools method (see thit link : http://forum.xda-developers.com/showthread.php?t=928343, there is a perfect tuto made for that)
And you could also use the root function included in Flashtool if you still want to root your phone
You should still be able to repair w/SEUS ("pc suite") or use flashtool.
X10 is pretty unbrickable.
To get into flash mode in your phone's current state take out the battery, connect the usb, hold the back button, and then replace the battery.
Hope this helps.
Sent from my X10a using XDA App
Hey guys, thanks for the replies!
I went through the flashing guide above and managed to get my phone working again (you were right, i could still start it up in flash mode if i took out the battery etc. first), and rooting it was pretty easy =)
Thanks again guys, the forum's a great resource.
AyDee said:
You should still be able to repair w/SEUS ("pc suite") or use flashtool.
X10 is pretty unbrickable.
To get into flash mode in your phone's current state take out the battery, connect the usb, hold the back button, and then replace the battery.
Hope this helps.
Sent from my X10a using XDA App
Click to expand...
Click to collapse
you just saved my bacon mate. got an xperia play but decided to have a play about with unlocking the bootloader on my old x10. needless to say i cocked up and bricked the phone. followed your post and finally managed to get flashtool to sort it. many thanks
tom
Help please. I'm basically in a boot loop with no recovery. Idk what I should do or if its possible to make a warranty claim.
Hey guys I'm in a boot loop of some kind. I'm not an advanced user of this stuff but idk what to do at this point. So this is the situation. I have a X10a from at&t and its rooted with busybox and freex10 recovery or whatever. I had a default 2.1 ROM and flashed the offline recharging thing. My phone seemed to work fine but then my battery died out. For a while I've had recharging problems with my phone either my cable is messed up or the usb port. So anyways after it died out I tried to recharge but I was in the 3x red flashing light problem and accidentally broke my charger cord, but continuing I borrowed my friends cord and still had problems so knowing my usb port is kinda broken i just left it there. After about 2 hours my phone majestically starts up lol. So I decided I wanted to put on xrecovery just incase and My computer wont read my phone. I try everything from takeing out my sd card to restarting my computer to reinstalling pc companion like 20 times. So I tried a factory reset through the phone settings and ended up where i currently am in a boot loop. It turns on and does the sony ericsson thing then does the boot animation then my phone vibrates and the screen darkens and my buttons are lit up. It has been like this for about 30 mins so far. I tried restarting my phone by taking out the battery and taking out the sd card/sim card.
Sorry for this being long but this is my situation. Could you please help me out? I Don't know if I can do a warranty claim or anything I'm desperate so please any help would be greatly appreciated. Thanks in advance. Also if there is anymore information you need please just ask.
the boot loop problem sounds like a wrong baseband issue, as for the usb problems you're experiencing I'm not sure how to help you there. Hopefully someone has an answer.
Just install stock generic 2.1 with Flashtool!
Install stock firmware through flashtool
Please hit a thanks if u r satisfied...
you can also use Sony`s SEUS to flash to stock 2.1. easiest way to return to stock
Yeah but my computer can't read my phone. I think it's because im using a HTC usb cable instead of the one issued by sony ericsson. That or my usb port on my phone is broken. Lets hope it's the first one. I'm gonna get a new cable soon
cloud911208 said:
Yeah but my computer can't read my phone. I think it's because im using a HTC usb cable instead of the one issued by sony ericsson. That or my usb port on my phone is broken. Lets hope it's the first one. I'm gonna get a new cable soon
Click to expand...
Click to collapse
I think you need to install the SEUS program by Sony Ericsson and has a download link on their website to get the phone drivers. Try it if you haven't tried it.
Sent from XDA Premium from my X10a rooted running 2.2.1 Pure CM Rom from kxhawkins
Had that same problem when I first flashed my phone. Either SEUS should do it or flashtool.
Is your computer picking up anything at all? Is it trying to recognise the phone at all?
Hi guys!
I have some problems with my X10i. First it all started with me wanted to go back to a previous backup with xRecovery. All this went wrong and got a message in xrecovery that it was not able to load sd-card. And then it was stuck on Sony Ericsson boot screen.
I got it flashed now, with Android 2.3, and wanted to root and install xRecovery, but when I start my phone and connect it to my comuter, it reboots. It wont stay on with USB connected to PC, so long till I can root.
I'm getting pretty irritated now.
What is wrong?
Hope you guys can help, and sorry for bad english.
Revert back to stock f/w pal u should be fine
Sent from my X10 using XDA
Thank you for your answer.
But do you mean to restore to 2.1? When I downloaded flashtool I got 2.1 with the program, do you mean to restore with this flash that came with flashtool program?
Flash
Try fix it with seus
Okay.. I updated my phone to newest, 2.3.3.
After I had updated the sony program said that I had to wait for my phone to reboot and not take out my battery for the first time, but my phone did not reboot. Nothing happend after I disconnected the phone. When I pressed the power button it only blinked green one time, so I took out my battery and rebooted.
Everything went fine in the beginning, couple of reboots that I expected after new software, but now my phone reboots and reboots. Sometimes I can't even get to the screen where I unlock my phone before it reboots. And even thou when charging, it reboots.
Omg.. so frustrating!!!
Please help! Should I restore to 2.3 or the 2.1 that came with flashtool program?