ok so i know how to do things on my vibrant but dont really know exactly how the phone does things (basically im a directions follower) so im going to try to be as precise as possible
my phone has been rooted for a while and ive been experimenting with a bunch of roms. i decided to flash TWs nero v3 w/voodoo and i was pretty sure id stick with that for a while but some of my games started having issues so i decided to flash the newest axura. now something told me that i needed to disable voodoo first and there is usually a voodoo submenu in CW recovery but there wasnt so i figured it was disabled already
so i flashed it and everything was going well untill my screen went blank
now my phone acts like there is no battery in it
ive tried any button combinations with charger in (wall or computer) or out.
no matter what my screen stays blank...plz help
im not exactly in a situation to just buy a new phone.
Unplug the phone from the charger. take your battery out for at least 15 seconds. plug the phone to your computer via usb. while holding both vol+/-, not power, put the battery back in. you should be in download mode.
use odin to flash a stock rom.
this all should work if you have the samsung drivers installed on your comp.
Go to this link it should help http://forum.xda-developers.com/showthread.php?t=848737&highlight=bricked+phone
btw i followed what both above said and neither worked for me =/
thanx for ur suggestions though
Ive seen alot of these post lately and all were on nerov3 .
Sent from my SGH-T959 using XDA App
Well I guess that your best bet would be modifying the usb charger with resistors. as stated in the link that jewbrad suggested. A similar thing happened to my phone when I tried to go back to stock from nero, but instead of a blank screen, I got a small icon of a pc and phone with a triangle in between. The method that I posted did the trick. Maybe you should try it again and check odin to see if it recognizes your device, even if the phone might look like its off.
Sent from my SGH-T959 using XDA App
Have you tried having odin open on you pc and loaded with eugene's froyo that doesnt brick then with your phone turned off(pull the battery then put it back in) now hold the volume keys up and down at the same time then plug your usb cord that is plugged into your pc into your phone this should get you into downlod mode. If this workes flash it and let odin do its thing after its done running it will reboot and go to a recovery screen then it will try to boot up ounce you see the i9000 screen you can pull the battery again and get it back into download mode the same way you did before and then flash the stock vibrant rom tar file and pit. I dont know if this will work but it cant hurt I know how it is not having your phone working so hope this helps
Same thing happend to me.
Please let me know if you get it fixed.
I was on Nero V3 trying to reflash because GPS didn't work well.
i got in to boot loop so i tried to get back to stock and re-do it,
and this happened.
I took it tmobile and claimed the ota broke it..they sent me a new one
NVM!! link posted by jewbrad had No-Boot phone instruction, and it worked!!!
Oh lucky...I tried that n it failed
Related
I was trying to use odin to get back to a stock rom (UVJFD). Phone was in download, odin was running. Odin suddenly said "not connected" and nothing was listed where com is usually displayed. I unplugged my phone and it immediately displayed a phone, exclamation, computer.
I tried the three button reboot, but it immediately went back to this screen. I've tried all of the options in the 'So you've bricked your phone' stickey, except the soldering method and I can't get it to do ANYTHING.
What do I do? I'm trying to get back to factory. At this point, I may need to send it in.
Just do what you would normally do to get back to download mode. I can't specifically remember the buttons but just jeep trying until it shows up on odin.
Actually I read somewhere that the phone "!" Cpu means that it will already work with odin so I guess try that. Im not certain that it will work immediately. If that doesn't work then do what I said first lol. Don't worry its not bricked this happened to me the day I got my phone hahaha
Sent from my SGH-T959 using XDA App
Phone....!.....PC is just like download mode. I was able to recover from it, when it happened to mine. Maybe the JFD you had was faulty?
But ODIN should recognize your phone.
Completely bricked?
shelbydz wrote: I tried the three button reboot, but it immediately went back to this screen
Click to expand...
Click to collapse
Does that imply that you saw some sort of life in the screen such as any light on the display? If that is the case it is probably worth trying the 301k Resistor method to get to the download screen.
On the other hand if your phone is exactly in the same shape as my phone is then I really feel for you. My screen never shows any life. It appears like the battery is dead and I've tried everything and I know the battery is fully charged.
So my next step is either finding someone with a jtag interface or send it off for repair.
Anyone have suggestions in that next step? Any weekend warriors with a jtag interface where we can send it? Any suggestions as to where to send it (t-mobile is not an option since I'm not using t-mobile)
It keeps rebooting to the icon screen (phone ! computer). I tried plugging it back in, but odin didn't see it.
I'll have to play around with it a bit more to see if I can get it to work.
thx
shelbydz said:
It keeps rebooting to the icon screen (phone ! computer). I tried plugging it back in, but odin didn't see it.
I'll have to play around with it a bit more to see if I can get it to work.
thx
Click to expand...
Click to collapse
Odin should recognize it, try using a different ODIN. Make sure ODIN is running first, with the proper files already loaded "PDA, MODEM, CSC" then plug in phone.
that seemed to work. (loading the files to odin, then connecting) Apparently I had a bad ROM image. It's booting up now.
Thanks for all of the help.
So i updated my vibrant last night from 2.1 eclair to 2.2 froyo through smasung kies mini.
Aftere it was done downloading and installing it says update finished and wait for phone to reboot. it hasnt rebooted ever since. i searched on all sorts of fourms this morning trying anything to get it to work. iv tried multiple download mode techniques but none of them work.
So my situation before this happen was i kinda missed the stock rom so i flash from bionix 1.3.1 to the true samsung vibrant stock rom 2.1 unrooted . and it worked everything was going great (I made sure i got all files of rooting,roms, kernlals,etc after) . i decided to put some music, videos ,etc and i decide to install the kies mini to get the update and as i said in the end it said done and wait till reboot and it never did.
It doesnt boot up , show logos, turn on, show charging icon when off and pluged in, it wont turn on!
So does anybody have any ideads or solutions?
Thanks you in advance to everyone.
Why exactly did you use kies?
Sent from my T959 using XDA App
well it was already on stock and i didnt want to mess with flashing again
laylovj said it all why?
but here this may help: For u, let ur battery sit for a few minutes before u pop it back in
power off phone
pull out battery
GRAB THIS STUFF : http://forum.xda-developers.com/showthread.php?t=1047087
turn on odin
attach phone to pc with usb cable
now while holding down both volume buttons put battery back in.
now you should be in download mode and go back to stock with odin from here!
make sure u put the proper .pit and .pda file in there proper places on odin and ur set to go.
Enjoy and also make sure u have the proper samsung drivers
i tried that way before and it didnt work. nothing turns ons not even the charging icon when off and plugged in.
I did notice that when i put the battery in and try to turn on leave it for like 5 min and i came back and the phone was warm. Any ideas pls???
I was trying to revert my wifes phone to stock and odin would not work. I used heimdell with the wrong file. The phone now has a i9000 interface. I cant call or text because it wants a sim card which obviously is impossible. and I cant get it in download mode to put the Fascinate interface back on it. Im an idiot!
Zerokillstreet said:
I was trying to revert my wifes phone to stock and odin would not work. I used heimdell with the wrong file. The phone now has a i9000 interface. I cant call or text because it wants a sim card which obviously is impossible. and I cant get it in download mode to put the Fascinate interface back on it. Im an idiot!
Click to expand...
Click to collapse
hey,
chill, user error happens. I know your wife probably can't see that right now but....
one time I did the same thing, sorta, and bricked and couldn't get into download mode. I couldn't get the phone to do anything, not even the charging animation. that is how you know its bricked.
it sat there unplugged and without a battery or sdcard for about 20 hours lifeless. I was in the process of ordering a new phone through insurance when I decided to hold my volume button down, plugged in and it was great!
once you get to this point, and you will if your phone is turning on at all its not bricked, then you will need to follow instructions for repartition like your coming off cm7mtd using a FULL BUILD like DI14 (I have a mesmerize so I'm not positive your full builds) with repartition checked using the atlas_2.2.pit file.
if that didn't work at all for you, there is a way to force download mode, using a homemade jig. google for galaxy s download mode jig if that's your only option.
good luck, and please do let us know how it goes for you. I've never used heimdall but its pretty similar to odin from what I've seen so that would probably work as well. if you're not sure if the rom you have for heimdall is a full build, open it with winrar/winzip our whatever and count how many files are inside, for me its 8 I think with full mesmerize build but we are missing one file that the fascinate build has I believe.
Sent from my SCH-I500 using XDA Premium App
perhaps if download mode is busted you could flash a fascinate rom after rooting and then boot to recovery and try flashing something a little closer to home like one of the pick n packs for the mesmerize...
but this would be one of the last things I would try, right before the homemade jig.
Sent from my SCH-I500 using XDA Premium App
Are you sure you're using the right button press for i9000? Like the guy above said try Vol button down and plug in.
Please Help me out.
I was using CynogenMod7 ROM. Could not write on my external SD card or mount it .
So decided to go back to Stock froyo firmware.
Tried ODIN to flash to my stock froyo firmware.
Had done it many many many a times earlier with success.
But ODIN could'nt complete the process, it kept on getting struck at Kernel and Factory some times.
Later thought there might be something wrong with bootloader.
Downloaded stock froyo bootloader.
Tried to ODIN the bootloader and got Struck at SBL many times ,Kept on trying then got struck at PARAM.
Removed the battery.
From than on NO Response what so ever combination buttons used.
No battery indicators,No light on Home keys, No signs of any power. Nothing Visible on screen & keys.
Tried usb JIG - no response.
Tried Ultimate UnBrick Resurrector-No response.
No lights .
Please solve my problem.
This may not work because I discovered this by accident. I bricked my phone so bad it looked like it wouldn't even turn on too. So, hopefully this works. Make sure you have your samsung drivers installed. Open Odin and connect the USB to the computer but not to the phone. Do a battery pull and do the three button boot, simultaneously connecting the USB to the phone. Most likely, nothing will happen. Hopefully, the phone will connect to Odin. Then, click start. That's right. Don't put any pit or tar files in, just click start. Hopefully, your phone will reboot to the vibrant screen and is stuck there. If it does, now you can reboot to download mode and Odin whatever files you wanted. If it doesn't work, just keep messing with the three button boot. I apologize for wasted time if it doesn't work. These steps are what I personally did on my phone. Hopefully, it works for you.
Sorry to say but I believe you have hard bricked your phone. If installing bootloaders goes wrong then your phone can turn into a paper weight. You could maybe try a jtag repair but I'm not sure it would help. You could call samsung and ask for a replacement, tell them you updated with kies or something but that's not exactly the truth
Sent from my SGH-T959 using Tapatalk
dr_rp1234 said:
Please Help me out.
I was using CynogenMod7 ROM. Could not write on my external SD card or mount it .
So decided to go back to Stock froyo firmware.
Tried ODIN to flash to my stock froyo firmware.
Had done it many many many a times earlier with success.
But ODIN could'nt complete the process, it kept on getting struck at Kernel and Factory some times.
Later thought there might be something wrong with bootloader.
Downloaded stock froyo bootloader.
Tried to ODIN the bootloader and got Struck at SBL many times ,Kept on trying then got struck at PARAM.
Removed the battery.
From than on NO Response what so ever combination buttons used.
No battery indicators,No light on Home keys, No signs of any power. Nothing Visible on screen & keys.
Tried usb JIG - no response.
Tried Ultimate UnBrick Resurrector-No response.
No lights .
Please solve my problem.
Click to expand...
Click to collapse
OK first, the stock images are 2.1 eclair not 2.2 froyo. Are you sure you have the right files? Are you sure your phone is a t959(3g, no front camera)and not t959v(4g, has front camera). Second, it sounds like a hard brick, if all else fails go to www.mobiletechvideos.com and check out the unbrickable mod and JTAG repair.
If you get your phone in DL mode and you have the correct Odin images, check the repartition box as well as others and run it.
Good luck
sent from my magic box to yours
Remove battery and sim and microsd. Leave out and press and hold power for 30 seconds or so. Leave battery out for a few minutes.
Put battery in and if you are on GB bootloader hold volume up and plug in USB. Might get you to download mode.
I did that with a friends phone about a year ago and got lucky. Odin recognized it. I read that somewhere here on XDA. May be a shot in the dark... but when you get desperate any new ideas to try can be a relief right?
Good luck to you.
After I messed with bootloaders and then tried to get back to stock with Kies I had this problem.
iTz KeeFy said:
You could call samsung and ask for a replacement, tell them you updated with kies or something but that's not exactly the truth
Click to expand...
Click to collapse
I called Samsung and told them that I was just trying to upgrade to 2.2 with their software and they replaced my PCB (printed circuit board) for no cost (including shipping). I have no idea if they tried to figure out if I had really used Kies (if they could even figure it out with the state my phone was in) or if they just replaced the PCB blindly. Worth a shot, I'd say!
Thanks for your concern.
Zeferden said:
This may not work because I discovered this by accident. I bricked my phone so bad it looked like it wouldn't even turn on too. So, hopefully this works. Make sure you have your samsung drivers installed. Open Odin and connect the USB to the computer but not to the phone. Do a battery pull and do the three button boot, simultaneously connecting the USB to the phone. Most likely, nothing will happen. Hopefully, the phone will connect to Odin. Then, click start. That's right. Don't put any pit or tar files in, just click start. Hopefully, your phone will reboot to the vibrant screen and is stuck there. If it does, now you can reboot to download mode and Odin whatever files you wanted. If it doesn't work, just keep messing with the three button boot. I apologize for wasted time if it doesn't work. These steps are what I personally did on my phone. Hopefully, it works for you.
Click to expand...
Click to collapse
Thanks for your concern.
But it did not work for me.
thanks
iTz KeeFy said:
Sorry to say but I believe you have hard bricked your phone. If installing bootloaders goes wrong then your phone can turn into a paper weight. You could maybe try a jtag repair but I'm not sure it would help. You could call samsung and ask for a replacement, tell them you updated with kies or something but that's not exactly the truth
Sent from my SGH-T959 using Tapatalk
Click to expand...
Click to collapse
Thanks for your concern
Its T mobile vibrant T959.
Its T-mobile Vibrant T959 without a front camera.
Totally no response.
No lights on soft keys ( Menu,Home,Back,Search)
No response even When connected with wall charger or PC.
Please help.
Thanks
dr_rp1234 said:
Its T-mobile Vibrant T959 without a front camera.
Totally no response.
No lights on soft keys ( Menu,Home,Back,Search)
No response even When connected with wall charger or PC.
Please help.
Thanks
Click to expand...
Click to collapse
Sorry to say this but your phone is hard bricked, as in nothing can save it but a JTAG or warranty service. You can try to call Samsung and say you hard bricked your phone cause of kies, it worked for another.
Sent from Mount Olympus via Hermes.
you can try this, it works for many user
http://forum.xda-developers.com/showthread.php?p=17858853#post17858853
HELP!
I need help with my Samsung galaxy SGH-T959 Vibrant I got bricked so I was fixing it with odin until my phone fell and it disconnected and red letters and numbers came out. when I try turning my phone on it doesn't until I press the buttons to go to download mode those red numbers come out and I can't do anything. Please Help
When you pulled the battery, after it hung up with Odin, you corrupted the primary Bootloader, because it wasn't completely written in......Last weak possible option is to try every rocker/battery/cable sequence ETC, to get Odin to handshake with the phone!!.....If there's still no sign of life after doing that....Your only option will be to have it JTAG,d in order to rewrite the primary bootloader file back in it.....it'll never power on unless the primary bootloader executes properly!!....you can corrupt the 2ndary BL and the phone will only be soft bricked, but a primary BL corruption is phone DEATH!!....Only place I know of that's reliable is: mobiletechvideos.com....send it to them, they'll rewrite the primary BL back in it and I think 2.1 or 2.2 for you and mail the phone back to you!!....Good luck let us know if you got it powered on with any combination, as that could save another Bricker from having to send it out!!
Randomness Guy........Start your own thread in the troubleshooting forum, AND QUIT TRYING TO HIJACK THIS THREAD!!
I just got a vibrant from another xda forums user, and the guy restored to stock 2.1 rom but when I plugin a charger or usb it reboots and stays black, I have already used odin 2 times to flash back to stock, still the problem persists, is there a fix?
I can enter download mode btw
thank you
http://www.droidforums.net/forum/te...screen-turns-off-when-plugged-into-power.html
I found this in Google. Don't know if this will help you or not, but about 3/4 of the way down on page 1 may help you.
didnt help, the phone reboots and stays off until i take out the usb cable/charger, except in download mode, weird
http://rootzwiki.com/topic/27596-q-phone-shuts-down-when-connected-to-usb/
This sounds like your issue. Install CWM and flash a custom ROM.. if for whatever reason you want Froyo, then I recommend Bionix V with the Bali kernel.
Or you could shoot high and try Helly Bean
Anyways, flashing past Eclair seems to be the solution to your particular problem. I would assume most people don't notice it because they don't stay on Eclair for more than a few seconds.
Hope this helps.
taha1112 said:
didnt help, the phone reboots and stays off until i take out the usb cable/charger, except in download mode, weird
Click to expand...
Click to collapse
try to flash bootloader (Only Stock/Froyo)
here is the link
http://forum.xda-developers.com/showthread.php?t=1117990