Is there a good resource/thread for learning more about using SetCPU? I just flashed nerov3 and im wondering if it'd be beneficial to install it. Not sure if its neccesary or compatible... etc. How does one even know how much is safe to over and underclock?
Vibrant, NeroV3, JL5, Voodoo...
With having nero v3 installed, you can't OC it because we don't have vibrant's froyo source code yet but we do have I9000's. You could use one of those kernels to oc/uc. Nero is speedy w/ voodoo anyways so you don't REALLY need it, if u want to use setCPU to uc you can. Underclocking i would recommend min100 max800 set scaling to conservative, which will automatically clock cpu to compensate for usage. (Just my 2cents, listen or don't its your choice)
I would highly recommend SetCPU with Nero V3 or any Rom for that matter. I know for some, It is just personal preference. For me, I run my phone at 800mhz max and 200mhz min. Gives me awesome speed, with voodoo there isn't really any lag. I'm basically reiterating what ucantak3dis has said, So until there is an OC kernel. Which I'm not sure if som and/or viral have plans for. I would stick with what you've got in addition with SetCPU. You'll get great battery life out of it! Enjoy.
Thanks for the feedback guys. I installed it and im running at 200 min, 800 max (set on boot).
What exactly does that mean?
Also, I've read people talk about underclocking when the phone is asleep to save battery. Do I need to create a profile to do that?
Vibrant, NeroV3, JL5, Voodoo...
trunkstar1 said:
Thanks for the feedback guys. I installed it and im running at 200 min, 800 max (set on boot).
What exactly does that mean?
Also, I've read people talk about underclocking when the phone is asleep to save battery. Do I need to create a profile to do that?
Vibrant, NeroV3, JL5, Voodoo...
Click to expand...
Click to collapse
It means that those values are SET on boot of your device. Your phone will run anywhere between 200 mhz and 800 mhz and ramp up to a max of 800 mhz (conservatively) when necessary. Versus, Without SetCPU your phone would constantly be running at 1Ghz. You can create profiles for doing such things to save battery while the screen is locked, I have had issues with my phone NOT being able to wake though. So, try this at your own risk.
Personally, i wouldn't recommend having the set on boot checked because it caused problems w/ some ppl. I did that once and when i rebooted, it froze on the vibrant screen. idk if that's been fixed but just having setCPU set at the values you want is fine i think. Profiles aren't necessary unless your overclocking the cpu.
Related
Thats right, just loaded it up after rooting this bad boy and it is working just fine!
I am not responsible if you brick your device in the process.
UPDATE!
Ok so here is what is needed to run this badboy without problems.
Use only the conservative option (least problematic and no sleep comas)
I dont use the widget, i already know the speeds i set it at.
The settings stick even after a reboot, but when you click on the setcpu icon they revert back and you lose your settings. If that happens just go back and click on detect auto speeds and set up your speeds again.
Happy clocking!
what version? 2.0.1?
Were you able to overclock it past the 1ghz?
I rooted mine today and installed setCPU which worked flawlessly but I am not able to move the slider past 1ghz.
I loaded it on mine and while it *appears* to work, it doesn't seem to effect the clocks any.
heck just underclock your phones to save battery lol
I can only seem to clock mines to 800? hmm. I noticed when i first opened setcpu it was clocked to 384/245!! wow so low
edit: setting it to nexus one/snapdragon Qsd it clocks to 1ghz exact. not really sure it's working though
jroid said:
I can only seem to clock mines to 800? hmm. I noticed when i first opened setcpu it was clocked to 384/245!! wow so low
edit: setting it to nexus one/snapdragon Qsd it clocks to 1ghz exact. not really sure it's working though
Click to expand...
Click to collapse
To see if it's working set it to underclock and then get into an adb shell and run the command: cat /proc/cpuinfo
It should display cpu data that includes the current clock speed.
I don't know if this helps but when I was in the Quadrant Standard app it has the system info. I hit it, scrolled down to cpu and it said
Current: 400 mhz, Max: 1000 mhz, Min: 100 mhz,
and I just checked it now and it said my current clock was 800 mhz, so i guess the cpu scales dynamically based on what the load is and what we are doing, thats a pretty great power saving feature.
Select 'Auto Detect'.
I believe you need an oc'd kernal to be able to move the slider past 1ghz.
Also, the dev has stated that it should be set to 'conservative', not 'ondemand'. 'Ondemand' was causing random shutdowns on the Galaxy S.
I installed SetCPU on my Vibrant too but removed it because it appears that it caused the phone to power off.
Does there need to be device specific support for a processor/device or does the auto-detect work on any processor?
Koblek said:
I installed SetCPU on my Vibrant too but removed it because it appears that it caused the phone to power off.
Does there need to be device specific support for a processor/device or does the auto-detect work on any processor?
Click to expand...
Click to collapse
Look at the post before yours.......from me.
SetCPU needs to be set to 'conservative' on the Vibrant, not 'ondemand'. Also, per the dev in the "Random shutdowns?" thread: "You can "simulate" ondemand by changing freq step in Advanced to 100%"
Has anyone noticed any significant battery conservation with this?
MINUS Stl said:
Look at the post before yours.......from me.
SetCPU needs to be set to 'conservative' on the Vibrant, not 'ondemand'. Also, per the dev in the "Random shutdowns?" thread: "You can "simulate" ondemand by changing freq step in Advanced to 100%"
Click to expand...
Click to collapse
Hey, sorry if this sounds like a stupid question, but why does it max out at 800,000?
i am still having problems with setcpu even on conservative mode. i have stopped using setcpu completely for now.
wbexpress said:
Hey, sorry if this sounds like a stupid question, but why does it max out at 800,000?
Click to expand...
Click to collapse
Auto detect...
Sent from my SGH-T959 using XDA App
i have this on my rooted vibrant. Max is 1000 and Min is 100. My battery life has doubled. I have not experienced any force closes, no slowness and no freezing. the phone is running super fast and smooth. Love it. After looking at the stats, it seems like the CPU uses 400 and 800 a lot.....thats probably where the extra battery life comes into play. 1000 is used when on full load.
mygti02 said:
i have this on my rooted vibrant. Max is 1000 and Min is 100. My battery life has doubled. I have not experienced any force closes, no slowness and no freezing. the phone is running super fast and smooth. Love it. After looking at the stats, it seems like the CPU uses 400 and 800 a lot.....thats probably where the extra battery life comes into play. 1000 is used when on full load.
Click to expand...
Click to collapse
What are your exact settings in profiles, advanced and overview?
any one running their phone at 1Ghz all the time?
+1, hah2110 please post your settings if they're working for you so a noob like me can learn some things!
The latest jt kernels and people's derivatives of them have not been playing well with SetCPU on my phone. It has been freezing up. Any advice on a certain version I should use or maybe settings issue?
Check to make sure profiles is not enabled. Using them will make your phone freeze and or not come back awake.
Also make sure your on conservative and not ondemand. I hear the ondemand is still being a little buggy.
Currently I'm running jt's oc kernel at 1.3ghz stable. Setcpu is on conservative and I have zero problems, only when I change to another setting does it have problems.
At this time what could I use setcpu for besides overclocking?
theres no point in using setcpu with jts kernels as theyre not overclocked...unless u need to UNDERclock for some reason
tonu42 said:
Check to make sure profiles is not enabled. Using them will make your phone freeze and or not come back awake.
Click to expand...
Click to collapse
I'm using setcpu to underclock my phone (for bettery battery life), and I set up a few profiles to drop the speed down when the screen is off (100 min, 200 max), and when the battery is below a certain amount (100 min, 400 max), and it seems to be running fine. No freezes, no problem waking up.
gkirby11 said:
Also make sure your on conservative and not ondemand. I hear the ondemand is still being a little buggy.
Currently I'm running jt's oc kernel at 1.3ghz stable. Setcpu is on conservative and I have zero problems, only when I change to another setting does it have problems.
Click to expand...
Click to collapse
JT doesn't have an OC kernel out. If you're using nemesis's OTB OC kernel then you shouldn't be using SetCPU, you should be using Voltage Control from market. SetCPU has caused some issues. This will give you orange CWM but you can always Odin the red one.
On a Samsung Vibrant (U.S.A.) with stock v2.2 what are the best settings, profiles, ect. for saving battery? Also please label the specifics like max/min, scaling, and your advanced settings. Thank you...
EDIT: I understand you can't overclock without a customized kernal, but if I recall correctly you can underclock without it. Am I correct?
If you underclock your phone, it might get better battery life, but it perfomance will go down too and will start lagging, i don't recommend it at all.
The vibrant doesn't like profiles with less than 800 Max, it tends to freeze on wake-up. The amount of savings from an 800 MHz screen off profile is almost immeasurable as well. Also, the default conservative governor is the only one that is reliable. Therefore unless you're overclocking to start with, setcpu doesn't do anything for battery life on our phones. Best to just use a UV kernel such as BALI.
Sent from my SGH-T959 using Tapatalk
Hey man, what you want is undervolt. Underclock will slow you down, and not make a huge difference. However I undervolt by 75mv through the spectrum and have seen great results.
can't hurt to underclock to 800 though, some kernels are ok at 400 but very laggy.
Vibrant - project v, bali 1.8.6UV
JettyLife said:
Hey man, what you want is undervolt. Underclock will slow you down, and not make a huge difference. However I undervolt by 75mv through the spectrum and have seen great results.
can't hurt to underclock to 800 though, some kernels are ok at 400 but very laggy.
Vibrant - project v, bali 1.8.6UV
Click to expand...
Click to collapse
Yes.
Don't underclock. It will make your phone hell.
UNDERVOLT.
thats good.
Ok, I'm posting here because after doing a search, this is the very latest SetCPU thread. Recently, we finally got a worthwhile Gingerbread JVP and several ROM's (Simply Honey 3.8 & Asgard 3.1 JUST AMAZING ROM's) have finally given us some 2.3's we can keep on our phones, well in my opinion anyway.
So, I'm using cmenard's latest Bullet GB Kernel v6.1 and have decided to finally put to use the profiles section on SetCPU. Below is what I'm thinking and would enjoy a friendly conversation of what/if any benefits can be had on Gingerbread and customs Kernels using SetCPU Profiles. I read somewhere that Android is getting much better in regards to battery/performance efficiency, but I noticed a slight fall in battery life on 2.3.4 over 2.2.1 by a few hours.
My Profiles at this time.
Main SetCPU screen
200 min - 1200 max - Conservative? Smartass? Interactive? Any particular Governor worth using other than stock Conservative? - Set on Boot = YES
I'm not quite sure how the priority works on the main screen, I mean let's say I'm at 21% battery life and its time for my battery profile to kick in, but I'm still using the phone for various reasons, wifi calling or benchmarking etc. Will the phone stay at 200-1200 or will it actually use my battery profiles?
Screen Off (Set at 10 minute timeout)
100 - 800 - Conservative - Priority 100
Battery <11%
100 - 400 - Conservative - Priority 75 (Really thinking I should delete this)
Battery <21%
100 - 800 - Conservative - Priority 50
Charging
100 - 800 - Conservative - Priority 25 (Trying to keep the phone cool)
I have read that the Vibrant does not like profiles of 400 or lower when the screen is off, and this must be true as I tried 100-400, 200-400, but they all gave me wake of death until I set the max to 800 (there was no in between a.k.a 500, 600 or 700), so now 100-800 seems to work great for Screen Off. I hate this since when the screen is off the phone does not need to be doing anything other then checking gmail via wifi and notifying me using BLN blinking. Also, I tried to set a profile for Battery temp, but for what ever reason it will NOT give me the save button, so I assume GB now controls that on its own, or cmenard has removed that option from his kernel (or setcpu is borked, lol).
Any tips or concerns with my settings above? Anyone here a guru with SetCPU profiles and can see I'm a noob with profiles? lol
Thanks
SkOrPn
Samsung Fascinate CDMA
Rooted MIUI 1.9.16
Did a brief search here looking to understand how to operate overclocking kernals, but find it/me relatively limited.
I have installed and ran Glitch v11 and v12, played around with HL to LL, and made adjustments to undervoltage utilizing Pimp My CPU and Voltage Control. I have also ran Tweak (though not really a kernal).
My question is this,
am I overclocking when I reduce voltage on Mhz's above 1,000?
If not, could someone point me to, or explain how to achieve overclocking on our phones, and
which kernel and governor do you prefer for overclocking?
As an ammended note, I've installed Tegrak Overclock, but am still looking for a user guide...
Thank you for your time.
If you're the running the glitch kernel...use voltage control, not tegrak overclock...over clocking is when you turn the CPU speed above its normal speed..anything over 1GHz.
under volting is when you turn down the voltage frequency to achieve better battery life...
Any one clock speed may perform more or less stable with different under volting unfortunately all of our phones will vary in performance so one setting that works for one may not be the best for another so experimentation is really the best option...this applies for schedulers and governors as well.
I personally overclock as high as I can until it freezes or crashes..then I go 1 setting down...I then try undervolting different steps observing the stability of my phone...when I find what I like,I run it for a few days, then if its still nice and stable I will apply on boot.
The different leakage values are affected by the hardware quality of the chips in our phones which also vary..I start with high and see how high I can overclock..note the setting, then try medium..see how high I can overclock and so on...just as a reference..high leakage creates the most heat and is the least efficient, but works for most phones, while low leakage is the most efficient and generates the least heat and will work with not as many phones
Sent from my SCH-I500 using XDA App
efan450 said:
If you're the running the glitch kernel...use voltage control, not tegrak overclock...over clocking is when you turn the CPU speed above its normal speed..anything over 1GHz.
under volting is when you turn down the voltage frequency to achieve better battery life...
Any one clock speed may perform more or less stable with different under volting unfortunately all of our phones will vary in performance so one setting that works for one may not be the best for another so experimentation is really the best option...this applies for schedulers and governors as well.
I personally overclock as high as I can until it freezes or crashes..then I go 1 setting down...I then try undervolting different steps observing the stability of my phone...when I find what I like,I run it for a few days, then if its still nice and stable I will apply on boot.
The different leakage values are affected by the hardware quality of the chips in our phones which also vary..I start with high and see how high I can overclock..note the setting, then try medium..see how high I can overclock and so on...just as a reference..high leakage creates the most heat and is the least efficient, but works for most phones, while low leakage is the most efficient and generates the least heat and will work with not as many phones
Sent from my SCH-I500 using XDA App
Click to expand...
Click to collapse
Efan450,
Thanks.
How do you over-clock using Glitch and Voltage Control? I see that Voltage Control goes up to 1,300Mhz, but it's at 0 above 1,000Mhz and can be dropped down to -200mV. Is overclocking just the process of decreasing that voltage on Mhz's above 1,000Mhz's
FJRSport said:
Efan450,
Thanks.
How do you over-clock using Glitch and Voltage Control? I see that Voltage Control goes up to 1,300Mhz, but it's at 0 above 1,000Mhz and can be dropped down to -200mV. Is overclocking just the process of decreasing that voltage on Mhz's above 1,000Mhz's
Click to expand...
Click to collapse
come on man.. Clock speed (mhz) and undervolting are 2 completely different things.. Forget the voltage.. No changing the voltage is NOT overclocking.. You overclock by changing your maximum clock above 1000mhz which is stock for this phone.. Try long pressing 1200mhz and selecting set as max.. Now your overclocked to 1200mhz..
Sent from the fascinate that holds the record benchmark on antutu
No decreasing the voltage is simply undervolting whether it's over 1000 or under. The idea behind undervolting is increasing battery life, but you can't necessarily go and set each level to the maximum undervolt (200) you half to see what works. Increasing the processor speed is overclocking, stock speed is 1000 so anything over that is over clocked. As far as how far as how far you can over clock depends mostly on 2 things, 1. the kernel your using, ( for example if it shows 1300 in the list that means thats all that specific kernel supports) 2. It varys greatly between phones. For example with glitch you can overclock to 1700 but very few phones can run that high for longer than a few minutes!
Hope that helps.
Sent from my SCH-I500 using xda premium
Yes.. And the fact you say your running glitch and your max oc is only 1300 my guess is you broke your kernel with tegrak overclocks module.. Delete tegrak and stop downloading overclock apps. or any other root app unless you know fully the consequences first.. If after deleting tegrak, and rebooting, if your voltage control don't show a maximum clock of 1700 mhz, then you will need to reflash your glitch kernel
Sent from the fascinate that holds the record benchmark on antutu
Neh4pres,
Yeah, I kind of feel like a heel. For some reason, I had a brain fart when looking in the 'General' section of Voltage Control. I see now how to overclock.
Regarding ost #6:
When I flashed MIUI 1.9.16, I did not install any kernel; so it was kind of a half truth in that while running 1.9.9 I did have Glitch installd. Nevertheless, I still have Voltage Control installed.
mkropf,
I see that now, and thought as such earlier, but needed some clarification.
Having so many issues with Glitch and 1.9.9, I'm hesitant to install Glitch, but interested to see if it runs better on the newer MIUI...
Thank you two for answering my newbie questions.
FJRSport said:
Neh4pres,
Yeah, I kind of feel like a heel. For some reason, I had a brain fart when looking in the 'General' section of Voltage Control. I see now how to overclock.
Regarding ost #6:
When I flashed MIUI 1.9.16, I did not install any kernel; so it was kind of a half truth in that while running 1.9.9 I did have Glitch installd. Nevertheless, I still have Voltage Control installed.
mkropf,
I see that now, and thought as such earlier, but needed some clarification.
Having so many issues with Glitch and 1.9.9, I'm hesitant to install Glitch, but interested to see if it runs better on the newer MIUI...
Thank you two for answering my newbie questions.
Click to expand...
Click to collapse
There are no issues with glitch.. It is what I run.. Very smooth.. Just have to give your phone time to adjust and build cache
Sent from the fascinate that holds the record benchmark on antutu
Landscape
Re-installed Glitch v12 ML last night and have it overclocked @ 1,200 with no under-voltage...yet. Want to see any adverse effects.
I started at 1,300 and it locked up then rebooted within 5 minutes.
A concern I have is that now my phone will not Auto Rotate to Landscape even though I have Auto-Rotate 'on' in Settings.
I've scoured Sixstrings Glitch thread to no avail. Though it's not needed anymore, I also flashed the cleaning script just to see if it would make a difference.
Is there a work around or fix for this?
Make sure you're on the latest 9/15 version of the kernel. Anything before that will kill all of your phone's sensors.
http://forum.xda-developers.com/showthread.php?t=1252871
sageDieu said:
Make sure you're on the latest 9/15 version of the kernel. Anything before that will kill all of your phone's sensors.
http://forum.xda-developers.com/showthread.php?t=1252871
Click to expand...
Click to collapse
That was it. I had re-installed the older Glitch v12 that was already on my PC. Deleted them and downloaded the newer Glitch kernels to experiment with.
Thanks!
FJRSport said:
Re-installed Glitch v12 ML last night and have it overclocked @ 1,200 with no under-voltage...yet. Want to see any adverse effects.
I started at 1,300 and it locked up then rebooted within 5 minutes.
A concern I have is that now my phone will not Auto Rotate to Landscape even though I have Auto-Rotate 'on' in Settings.
I've scoured Sixstrings Glitch thread to no avail. Though it's not needed anymore, I also flashed the cleaning script just to see if it would make a difference.
Is there a work around or fix for this?
Click to expand...
Click to collapse
under volting helps stability.. I use -50 for everything above 1ghz.. Your phone may vary
Sent from the fascinate that holds the record benchmark on antutu
OC & UV settings
neh4pres said:
under volting helps stability.. I use -50 for everything above 1ghz.. Your phone may vary
Sent from the fascinate that holds the record benchmark on antutu
Click to expand...
Click to collapse
Yeah, locking and rebooting was while using the older version of Glitch v12. With the 9/15 dated Glitch I'm at 1300 now with the following settings:
Deadline / ondemand
200 - 1300
1300 -25
1200 -25
1000 -50
800 -50
400 -75
200 -75
1.2GHz is the best I say if you want good battery with a higher frequency. 1.4GHz is the best for anyone who uses their phone alot. Samsung did add 1.2GHz overclock in their source.
Sent from my SCH-I500 using XDA App
Back to running MIUI without Glitch.
Things that make you go, Hmmm?
For some reason, every time I accessed the keyboard for Google+, it hung, then froze, and 3 of the four times rebooted. The fourth time I needed to remove the battery to reboot. So I re-flashed MIUI 1.9.16 (effectively removing Glitch) and have 0 problems.
Bummer, I like Glitch too.
I'm in the same boat, however they redone the latest glitch merge and posted it last night so I'm thinking we'll be back in good times
Sent from the most custom, custom rom Miui 1.9.16 and currently the best kernel Jt
mkropf said:
I'm in the same boat, however they redone the latest glitch merge and posted it last night so I'm thinking we'll be back in good times
Sent from the most custom, custom rom Miui 1.9.16 and currently the best kernel Jt
Click to expand...
Click to collapse
are you using JT's 9/12 kernel?
if so...did you overclock it?
i'm on jt's 9/12 with miui 1.9.16 and wondering if I can / should overclock and undervolt it. I'm just trying to maximize battery life at this point.
Try the new glitch posted last night, it is fantastic.
Sent from my MIUI SCH-i500
sageDieu said:
Try the new glitch posted last night, it is fantastic.
Sent from my MIUI SCH-i500
Click to expand...
Click to collapse
what voltages are you running?
also for anyone..
is there any way to directly compare two kernels? like a test or something?
I can't decide between JT's 9/12 and the new glitch..
worshipNtribute said:
what voltages are you running?
also for anyone..
is there any way to directly compare two kernels? like a test or something?
I can't decide between JT's 9/12 and the new glitch..
Click to expand...
Click to collapse
You wouldn't want to use my voltages, I put everything way lower than anybody else does or recommends and am just lucky that it is stable for me but it causes the sleep of death for anyone else.
For comparison, just run JT's kernel for a bit and then flash glitch and try it... once you play with OC/UV and voodoo color you won't be able to go back. (you'll be able to but you'd have to be insane.)
So I'm interested in undervolting using the stock CPU freq's, and I'm going to be using setCPU (obvi).
So, first question: Even if I want to use the stock frequencies, do I have to be using the OC kernel (0.2.1/1.45ghz at the time)? And then adjust the max to 1000mhz?
Second, I started up SetCPU and whenever I go to the voltage tab it forcecloses. This happens with both the stock enhanced & OC kernel, and I've tried fixing permissions to no avail.
All I really understand so far is that the end result is a table of CPU frequencies and linked voltages. I've OCed the hell out of desktops, but I'm lost here.
I'd just like to know how to get from starting up setcpu to ultimately popping out that new voltage/freq table.
I do apologize if this seems kinda stupid, I'm just trying to exercise caution lest I demolish my phone's innards. I've done it with many an intel.
If you just want stock frequencies, then there's no need for a custom kernel. I guess in that case, you could just use SetCPU for undervolting & profiles.
However, if you want overclock, you'll need a custom kernel.
If you're going to be using a overclocked kernel (i.e. the new Faux 1.45 GHz), then you will need to set the max to 1.45 GHz, and make sure SetCPU is set to start on boot; other wise it will stay at the stock clock speed of 1 GHz... So i guess if you only wanted the OC at certain times, you could set the max speed manually, only when you want to, and not select to start on boot.
I haven't really had any success with undervolting yet... always crashes on me & reboots. The best thing to do is make sure "set to boot" is not selected, when testing your undervolting, other wise you could get stuck in a loop, with the phone crashing every time it boots and tries to apply you undervolting values. I'd start at -25 for each and work from there... stress testing each choice with a benchmark app to make sure you wont reboot... if it reboots, then you know your undervolt was to much. Also remember that you can not undervolt more than -100 between each frequency, otherwise the undervolting will not make any difference.
I really like the profile options in SetCPU... you can set the screen off frequencies to the lowest two, that way for whatever reason your phone isn't running at full strength while your not using it. Also, you can set frequency speeds at custom defined battery levels.
Hope this helps somewhat.
It's unclear to me why it force closes. This may be a rom incompatibility or a SuperUser issue? I assume you've tried uninstalling it and reinstalling it? Updating your SU app? Try flashing to the latest Aura rom?
A few quick words about SetCPU:
1. When you first get started, do not set to "Set on Boot" in case you've undervolted too much and it crashes when applied. You can always check it later once you know the voltages are stable.
2. Between each frequency step there is a maximum of 100mV step off. Anything greater than that it defaults to native voltage. I think this is a Tegra2 issue.
With that said, undervolting is simple: simply slide the little slider on SetCPU to negative values. How much you can under-volt largely depends on your particular hardware and it is inconsistent across all Atrix's. My voltage table is as belows:
1000mhz: -50
912: -50
750: -50
608: -75
456: -75
312: -100
216: -100
I, however, did not test the limits of my phone. Many people will slowly increment the voltage lower until they start to get resets, and then they'll move it back to find the lowest stable point.
It has, however, been well established that minor undervolting improves battery life and diminishes heat generation. Excessive undervolting may actually hurt battery life. You can look around on this forum regarding the data. However, reasonable undervolting will improve battery life.
Thanks fellas, this helps A LOT.
I was so afraid I'd get 17 responses of "You're such a noob. Stop cluttering the forums" etc etc
At this point, I think that the problem is, for whatever reason, the FC when I tap the voltages tab.
I'm on the newest Aura (1.2.2.1) newest enhanced stock kernel from Faux123 (0.2.1) and the newest SetCPU (2.4). I'll try updating my SU (though I believe I did that right after I flashed.
I'll reintall SetCPU and report back.
Until then, THANKS BUCKETS fellas. I really appreciate the info and advice.
UPDATE: May have found the problem. When it first boots up it prompts to autodetect freq's or choose them manually (or something like that). I was afraid this would actually alter my CPU clocks right then and there and so I hit manual detect, saw something that said Tegra2 etc and clicked it. I just now hit 'menu' and set it to autodetect, tried the voltages tab, and no FC, so I think that's solved.
Thanks again for all the info guys! I'll start experimenting and let you know HOW LOW I CAN GO (ha).
You guys get force closes due to kernel problems. You have to ask your developments. There might be something wrong with some of your cpu voltage drivers. So yeah that's why just a tip. Only overclock when you're playing some high end game. If not stick to normal. If not your phone might get overheated and damaged
Accidentally sent from my Ultra-speedy SG3 using Tapatalk
AdiNova said:
You guys get force closes due to kernel problems. You have to ask your developments. There might be something wrong with some of your cpu voltage drivers. So yeah that's why just a tip. Only overclock when you're playing some high end game. If not stick to normal. If not your phone might get overheated and damaged
Accidentally sent from my Ultra-speedy SG3 using Tapatalk
Click to expand...
Click to collapse
It's cool bro the problem was totally a user goof by me. I kind of agree with your OC philosophy though, primarily because 1ghz with this proc an RAM seems ample and I don't do much gaming.
Real quick:
When undervolting, should I do it one freq step at a time? Or can I do ALL of them at say -25, stress test, then adjust? Also, what's a good stress test that'll force the proc to hit all the different freqs instead of just the max clock and then the minimum when it's idling/the screen is off?
xyrovice said:
It's cool bro the problem was totally a user goof by me. I kind of agree with your OC philosophy though, primarily because 1ghz with this proc an RAM seems ample and I don't do much gaming.
Real quick:
When undervolting, should I do it one freq step at a time? Or can I do ALL of them at say -25, stress test, then adjust? Also, what's a good stress test that'll force the proc to hit all the different freqs instead of just the max clock and then the minimum when it's idling/the screen is off?
Click to expand...
Click to collapse
Id start at -25 for all. Setcpu has a built in stress test under info, I think. Could also try a benchmark to test it. As general rule if thumb, then lower frequencies can be undervolted more, while the higher ones take some tweaking... I can't even do -25 on my 1000, b/c ill eventually get a reboot, maybe not right away, but eventually. Every device is unique when it comes to undervolting.... just remember to not set the undervolt part to auto on boot, until you get it somewhat stable.
Sent from my MB860 using xda premium
Swiftks said:
Id start at -25 for all. Setcpu has a built in stress test under info, I think. Could also try a benchmark to test it. As general rule if thumb, then lower frequencies can be undervolted more, while the higher ones take some tweaking... I can't even do -25 on my 1000, b/c ill eventually get a reboot, maybe not right away, but eventually. Every device is unique when it comes to undervolting.... just remember to not set the undervolt part to auto on boot, until you get it somewhat stable.
Sent from my MB860 using xda premium
Click to expand...
Click to collapse
Got it. I figure that 'set on boot' checkbox is basically a wedding ring ha. Thanks for the advice and insight my friend.
Also (as I run my first stress test with -25 across the board) if I get reboots early on, should I assume it's the higher voltages and that I should back off on the fast end of the clocks?
xyrovice said:
Got it. I figure that 'set on boot' checkbox is basically a wedding ring ha. Thanks for the advice and insight my friend.
Also (as I run my first stress test with -25 across the board) if I get reboots early on, should I assume it's the higher voltages and that I should back off on the fast end of the clocks?
Click to expand...
Click to collapse
When testing each frequency just set your min/max mHz to the level your testing i.e. min/max=1000. UV and stress test at that frequency and if it's stable, move to min/max=912 and so on.
FYI, my MHz might be different than yours, I'm on the stock enhanced.
ghost_og said:
When testing each frequency just set your min/max mHz to the level your testing i.e. min/max=1000. UV and stress test at that frequency and if it's stable, move to min/max=912 and so on.
FYI, my MHz might be different than yours, I'm on the stock enhanced.
Click to expand...
Click to collapse
That makes perfect sense- limiting the max during the stress test. Thanks for the tip bro I really appreciate it.