I odin to KA6 from KA5, including the sbl.bin. When I odin from KA6 to KA7 using the stock ROM, odin hanged at transfering sbl.bin. After waiting for 10 minutes or so, I have to disonncect, remove/reinsert the battery and reboot. The dreaded phone-dotted line-computer with an exclamation point appeared. I tried all the manuvers I can find on the forums but failed to get to the download mode screen. I was desperate and called T-mobile. The tech rep instructed me how to "master reset" the phone, without success. The rep transfered me to Samsung tech support. I was instructed to to the "master reset" a few time without success. I was transfered again to a second level Samsung tech support. I waited for nearly 30 minutes without reaching a human being. I hanged up and called T-mobile again. I was finally offered a replacement. After than, I tried again all the button/battery/usb adapter combinations without being able to get past the phone-computer-exclamation point screen. As the last resort, I tried flashing KA6 with Odin 1.3 in this "brick" mode. Surprisingly, Odin recognised the phone and added a modem port. I was successful in flashing KA6 without seeing the downlaod mode screen. I then flash KA7, again successfully. I just wish to report this for the reference of anybody encountering a similar situation. The new sbl.bin in KA6 may have altered the behavior of the bootloader so that the phone will be automatically be put in download mode if anything goes wrong. That essentially makes the vibrant unbrickable. Just my guess...
chtse53 said:
I odin to KA6 from KA5, including the sbl.bin. When I odin from KA6 to KA7 using the stock ROM, odin hanged at transfering sbl.bin. After waiting for 10 minutes or so, I have to disonncect, remove the battery and reboot. The dread phone dotted line computer with an exclamation point appeared. I tried all the manuvers I can find on the forums but failed to get to the download mode screen. I was desperate and called T-mobile. The tech rep instructed me how to "master reset" the phone, without success. The rep transfered me to Samsung tech support. I was instructed to to the "master reset" a few time without success. I was transfered again to a second level Samsung tech support. I waited for nearly 30 minutes without reaching a human being. I hanged up and called T-mobile again. I was finally offered a replacement. I tried all the button/battery/usb adapter combinations without success getting anything beyond the phone-computer-exclamation point screen. As the last resort, I tried flashing KA6 with Odin 1.3 in this "brick" mode. Surprisingly, Odin recognised the phone and added a modem port. I was successfully in flashing KA6 without seeing the downlaod mode screen. I then flash KA7, again successfully. I just wish to report this for the reference of anybody in a similar situation. The new sbl.bin may have altered the behavior of bootloader so that the phone will be automatically be put in download mode if anything wrong happens. That essentially makes the vibrant unbrickable. Just my guess...
Click to expand...
Click to collapse
wrong section for posting this
@birgertime....this sounds like what happened to you lol
Someone on the General thread had this happen also.. instead of anything working for the soft brick, when he plugged his phone in with ODIN open it brought up a COM port and he finally said "well, I'll try to flash it anyway" and it went.
Good "Need to Know" Info
I had a similar experience. I flashed KA7 and needed to flash another rom, so I went about flashing voodoo via ODIN and it failed and I was stuck at that screen.
I was freaking out a little because I couldn't get into download mode (even tried my jig).
Throughout the whole process I did notice ODIN recognized my phone as if it was in DL mode, which I thought was a little strange.
Anywho after trying everything I decided to try again. So I flashed the kernel again (in the phone ! pc screen) and it worked...
Sooooo...maybe the secondary bootloader allows you a way out if you screw up a flash............
jmcghee1973 said:
Sooooo...maybe the secondary bootloader allows you a way out if you screw up a flash............
Click to expand...
Click to collapse
or maybe it sucks worse than before and is easier to brick
I'd prefer your way though
i had the same thing hapopen to me today . odin hanged ,pulled battary out and dload mode shows phone dot computer icon , plugged in cable and started odin and it showed com port and reflashed it ..worked.
maybe that's the new download mode? lol
Sent from my SGH-T959 using XDA App
iynfynity said:
maybe that's the new download mode? lol
Sent from my SGH-T959 using XDA App
Click to expand...
Click to collapse
It's not. I had a similar experience as some of the others in this thread, but it seems that it is some sort of extra failsafe mode. Because I could NOT get into download mode when this happened.
Is there any special reason you were using ODIN? ClockworkMod seems a far more reliable flashing method than Kies (Mini) or ODIN IMO. I only use ODIN when I can't use ClockworkMod. I like to think I have avoided many (soft)bricks this way. A co-worker of mine bricked his phone by using ODIN with a intermittently connecting USB cable, had he used ClockworkMod instead he likely would have been fine since there's no cable involved. This is an attempt to prevent future bricks, nothing more. Thankfully, I was able to fix it for him.
Moved of: Samsung Vibrant > Vibrant Android Development
To: Samsung Vibrant > Vibrant Q&A
Please put your questions to: Vibrant Q&A
I had the same issue. My phone would not boot or get into download mode so it wouldn't get recognized by Odin or ADB. All I could do it get the phone, exclamation point, computer graphic. After a ridiculous combination of things tried, I was able to get it to download mode by unplugging USB and battery out. Then while holding down volume buttons, plug in the USB cable. This [finally] allowed me to get back to download mode. Hope it helps.
Related
Hi all. I have searched for this problem and found some similar ones, but nothing quite like this.
The problem first started when I tried flashing Zedomax Kernel v3 via Odin. Odin reported a successful flash, but when it went to reboot it sat at the Galaxy S2 splash screen with yellow triangle for about 45 mins. I figured something was wrong so rebooted to CWM. I was able to get into both CWM and download mode at this point.
No matter what I tried I could not get the phone to boot up, so I thought I would try flashing a factory image to get back to out of the box settings. In the middle of this Odin got stuck on a step and then failed out after a good 10-30 minutes (sorry for lack of detail, this was pretty late last night).
Now, when I try to boot into recovery mode I see the [phone]....!....[computer] screen with the message "Firmware upgrade encountered" (part of this screen is cut off on the right, and appears to overflow to the left side? weird). I can boot into download mode, but Odin doesn't see my phone when I plug it in. The device doesn't show up in device manager either.
Things I have tried:
-Different USB port
-Kies "Resolution connection errors" button, which seems to reinstall the drivers
-Reboot computer after above step
-Remove battery from phone and replace
After these steps I still can't get my computer to see my plugged in phone in any way. I'm getting kinda nervous but the only thing giving me hope is that I can get it into download mode. Any ideas on how to get Odin to see it again?
Remove Kies and reinstall see if it picks the phone up and installs the drivers .
jje
OperationIvy85 said:
Hi all. I have searched for this problem and found some similar ones, but nothing quite like this.
The problem first started when I tried flashing Zedomax Kernel v3 via Odin. Odin reported a successful flash, but when it went to reboot it sat at the Galaxy S2 splash screen with yellow triangle for about 45 mins. I figured something was wrong so rebooted to CWM. I was able to get into both CWM and download mode at this point.
No matter what I tried I could not get the phone to boot up, so I thought I would try flashing a factory image to get back to out of the box settings. In the middle of this Odin got stuck on a step and then failed out after a good 10-30 minutes (sorry for lack of detail, this was pretty late last night).
Now, when I try to boot into recovery mode I see the [phone]....!....[computer] screen with the message "Firmware upgrade encountered" (part of this screen is cut off on the right, and appears to overflow to the left side? weird). I can boot into download mode, but Odin doesn't see my phone when I plug it in. The device doesn't show up in device manager either.
Things I have tried:
-Different USB port
-Kies "Resolution connection errors" button, which seems to reinstall the drivers
-Reboot computer after above step
-Remove battery from phone and replace
After these steps I still can't get my computer to see my plugged in phone in any way. I'm getting kinda nervous but the only thing giving me hope is that I can get it into download mode. Any ideas on how to get Odin to see it again?
Click to expand...
Click to collapse
That kernel is for the Epic touch 4g is that your phone or do you have the international version? If you flashed the wrong kernel it could cause problems.
Yes it's an Epic touch 4g from sprint.
EDIT: Uninstalled Kies, reinstalled Kies, restarted computer, still no kind of recognition of my phone in any state (powered off, at "Firmware upgrade encountered" screen it boots into, or in download mode). Starting to get nervous, I used to at least hear a sound when plugging my phone into my comp. It is like there is nothing on the other end of the USB cable.
More things I have tried:
-All of the above steps on a different computer
-Sweet talking it
-Talking dirty to it
Am I brick'd? I figure not, since I can at least get into download mode. Not sure what else I can do though. I'd go see what the Sprint store can do for me, but on the download mode screen it lists my custom binary download count as 5, I understand they will see that and tell me I'm out of luck?
OperationIvy85 said:
More things I have tried:
-All of the above steps on a different computer
-Sweet talking it
-Talking dirty to it
Am I brick'd? I figure not, since I can at least get into download mode. Not sure what else I can do though. I'd go see what the Sprint store can do for me, but on the download mode screen it lists my custom binary download count as 5, I understand they will see that and tell me I'm out of luck?
Click to expand...
Click to collapse
Try to reset your binary counter with a usb jig.
you could try and download the drivers again from here and see if it then connects
http://modem-techno.blogspot.com/2010/09/epic-4g-usb-driver-download.html
I also had a similar problem once with an old i9000 and what worked was doing this and then connecting the phone first and then opening Odin.For some reason opening Odin first and connecting wouldnt find the phone.If nothing else works try wipeing the bin counter with the jig and send it back.Youll have to say that kies crashed while updating on Win7 64bits.Samsung know that before the September 30th kies update kies wasnt fully functional with 64bit drivers and they had a few phones replaced under warranty because of crashing kies updates on Win7 64bits.
Thanks for the replies everyone.
I made a USB jig but it had no result. I checked the resistance with a multimeter and I am connected across pins 4 and 5 of the usb dongle I bought. I plug it in and nothing happens.
I can still get into download mode by the usual means, just no recognition from my computer, odin, or kies. Very frustrating. Am I going to have to buy a new one or is there another way to reset the bin counter?
EDIT: Got the USB jig to work! I was using a bad diagram and was on pins 1/2 instead of 4/5. Now I can't boot, can't get to recovery, can't get any PC to recognize my phone in download mode.. but at least my download screen says "Custom binary download: NO." So if nothing else works before tomorrow evening I'm gonna bring this thing back to the Sprint store and tell them what cooza said about kies crashing on win7 64 bit. Thanks everyone! Also I just realized there is a specific forum for Epic 4G touch.. sorry >.>
The good thing is that your bin counter is at "0" again.The Kies thing is the real deal as there are also posts here on XDA of the same thing happening.I also know its true from first hand experience as it has happened to me and when i told them about the Win7 64bit driver problem (this happened to me a couple of months back too) they had no option but to accept it cos they know its true.Also i offered to e-mail links from forums with other complaints from users on 64bit PCs but they didnt even dought my storey and in 4 days it was back in my hand.I told them that when the update finalized the programe froze and the phone rebooted to a black screen.Had to pull the battery cos it appeared to be dead and refused to reboot again.Important to say that you where on Kies prior to the update I mentioned.Ived update to the latest Kies and it works fine now on my Win7 64bit so be carefull there that date is important
Thanks cooza I really appreciate your help. I do have a couple questions though.
1. Is the update you are referring to an update to Kies software.. or an update to the Galaxy S2? Reason I ask is because my phone is the Epic 4G Touch (accidentally posted in this forum >.>), will they still believe my story?
2. Not sure if you will know the answer to this one, but should I go through Samsung tech support or can I take it back to the Sprint store where I bought it?
3. Just trying to get clear on the story I should tell them. I was using Kies to update my phone on a Win7 64bit computer, but I accidentally used the version of Kies from before the Sept. 30 update? And then the phone crashed resulting in it's current state. Correct? Anything else I should watch out for?
4. With the problem you are describing with Win7 x64, does the phone go into a soft brick where it won't boot up?
Thanks again.. you've been very helpful
OperationIvy85 said:
Thanks cooza I really appreciate your help. I do have a couple questions though.
1. Is the update you are referring to an update to Kies software.. or an update to the Galaxy S2? Reason I ask is because my phone is the Epic 4G Touch (accidentally posted in this forum >.>), will they still believe my story?
2. Not sure if you will know the answer to this one, but should I go through Samsung tech support or can I take it back to the Sprint store where I bought it?
3. Just trying to get clear on the story I should tell them. I was using Kies to update my phone on a Win7 64bit computer, but I accidentally used the version of Kies from before the Sept. 30 update? And then the phone crashed resulting in it's current state. Correct? Anything else I should watch out for?
4. With the problem you are describing with Win7 x64, does the phone go into a soft brick where it won't boot up?
Thanks again.. you've been very helpful
Click to expand...
Click to collapse
Kies via to its Sep 30th update was not fully compatable with 64bits and gave a lot of problems to a lot of people.I had a few problems with it when I got a new laptop (HP Win7 64bit) so started searching the web for solutions and found that kies was designed mainly to support the windowsXP versions 32bit and had caused Samsung to accept various repairs under warranty because of crashing Kies updates mainly on android running phones.For some reason Bada didnt seam to affected.Maybe cos there arnt to many around like android.In the 4G forum there is post from someone who has bricked their phone using Kies to update and a reply from another with the same problem.Take it into where you bought it to start with and if its not there problem then they might send it back to Samsung for you.All you need to say is that you where updating your firmware via kies and on completion it froze and the phone booted to a black screen like mine did.You had to pull the battery and restart your PC to close Kies cos it wouldnt close or minimize or anything.Tell them that you searched on the net for possible causes and found what i told you about Kies and since you have a Win7 64bits PC then thats most likely to have been the cause.Your bin counter is at 0 so there is no way they can counter-attack your story.
OperationIvy85 said:
Hi all. I have searched for this problem and found some similar ones, but nothing quite like this.
The problem first started when I tried flashing Zedomax Kernel v3 via Odin. Odin reported a successful flash, but when it went to reboot it sat at the Galaxy S2 splash screen with yellow triangle for about 45 mins. I figured something was wrong so rebooted to CWM. I was able to get into both CWM and download mode at this point.
No matter what I tried I could not get the phone to boot up, so I thought I would try flashing a factory image to get back to out of the box settings. In the middle of this Odin got stuck on a step and then failed out after a good 10-30 minutes (sorry for lack of detail, this was pretty late last night).
Now, when I try to boot into recovery mode I see the [phone]....!....[computer] screen with the message "Firmware upgrade encountered" (part of this screen is cut off on the right, and appears to overflow to the left side? weird). I can boot into download mode, but Odin doesn't see my phone when I plug it in. The device doesn't show up in device manager either.
Things I have tried:
-Different USB port
-Kies "Resolution connection errors" button, which seems to reinstall the drivers
-Reboot computer after above step
-Remove battery from phone and replace
After these steps I still can't get my computer to see my plugged in phone in any way. I'm getting kinda nervous but the only thing giving me hope is that I can get it into download mode. Any ideas on how to get Odin to see it again?
Click to expand...
Click to collapse
I also have this same problem now. Except that....I cannot even get into download mode. My phone is stuck at the [phone]....!....[computer] screen, but without any message. I am told that the exclamation mark tells Samsung that warranty is voided.
Is there anyway I can do anything to save my phone?
Who told you that the exclamation point means you voided your warranty?
bajaber said:
I also have this same problem now. Except that....I cannot even get into download mode. My phone is stuck at the [phone]....!....[computer] screen, but without any message. I am told that the exclamation mark tells Samsung that warranty is voided.
Is there anyway I can do anything to save my phone?
Click to expand...
Click to collapse
The exclamation point on a normal boot up screen (Galaxy S II splash screen) means there is a custom rom installed. This can be removed with a USB jig, which will also reset your custom binary counter.
I have absolutely no idea still what [phone]....!....[computer] means though. I ended up taking my phone back to the Sprint store and they replaced it for a small service charge while telling me next time I won't be so lucky. My next step was going to be to try calling Samsung with the story cooza suggested. I told that same story to the people at Sprint but they definitely didn't buy it, but you may have better luck with Samsung. If you get this resolved I'd be curious to hear how, but I am not optimistic for you
bajaber said:
I also have this same problem now. Except that....I cannot even get into download mode. My phone is stuck at the [phone]....!....[computer] screen, but without any message. I am told that the exclamation mark tells Samsung that warranty is voided.
Is there anyway I can do anything to save my phone?
Click to expand...
Click to collapse
The sign you see means that your phone is semi-bricked and that you needed a jig to force the phone to boot into download mode.You can buy one on ebay for a couple of bucks.Best you do cos it could may mean that your warranty is void.Let me explain,no one can actually say that your warranty is void because of this sign but being only "semi-bricked" the service centre are still able to enter the phone and see the bin counter.So if you semi-bricked flashing a non official firmware or you have done so earlier and your bin counter is not at 0 then YES your warranty is void.Semi-brick is not so bad as you can normally fix it yourself but Hard-brick is a dead phone and you gotta pay for a jtag .In your case buy a jig force the phone into download mode and re-flash it yourself.You shouldnt need to go anywhere.Semi-bricking is something you save yourself.Just wait till the jig arrives in the mail.
EDIT:there have been posts of people pulling the battery for 10min and re-trying and it has booted to download.They say they have had to do so 4 or 5 times for it to finally work but if youve got time on your hands then give it a try.
---------- Post added at 04:48 PM ---------- Previous post was at 04:22 PM ----------
OperationIvy85 said:
The exclamation point on a normal boot up screen (Galaxy S II splash screen) means there is a custom rom installed. This can be removed with a USB jig, which will also reset your custom binary counter.
I have absolutely no idea still what [phone]....!....[computer] means though. I ended up taking my phone back to the Sprint store and they replaced it for a small service charge while telling me next time I won't be so lucky. My next step was going to be to try calling Samsung with the story cooza suggested. I told that same story to the people at Sprint but they definitely didn't buy it, but you may have better luck with Samsung. If you get this resolved I'd be curious to hear how, but I am not optimistic for you
Click to expand...
Click to collapse
Well at least you got a phone now hope they didnt charge to much!!!!Good on ya mate
Update on my issue....
It turns out the problem is because I tried to flash an I1900 firmware while my phone is a G variant (I900G).
After using the right firmware, it worked.
OperationIvy85 said:
Thanks for the replies everyone.
I made a USB jig but it had no result. I checked the resistance with a multimeter and I am connected across pins 4 and 5 of the usb dongle I bought. I plug it in and nothing happens.
I can still get into download mode by the usual means, just no recognition from my computer, odin, or kies. Very frustrating. Am I going to have to buy a new one or is there another way to reset the bin counter?
EDIT: Got the USB jig to work! I was using a bad diagram and was on pins 1/2 instead of 4/5. Now I can't boot, can't get to recovery, can't get any PC to recognize my phone in download mode.. but at least my download screen says "Custom binary download: NO." So if nothing else works before tomorrow evening I'm gonna bring this thing back to the Sprint store and tell them what cooza said about kies crashing on win7 64 bit. Thanks everyone! Also I just realized there is a specific forum for Epic 4G touch.. sorry >.>
Click to expand...
Click to collapse
Hi, I'm having an exactly same problem with you and I just got a USB jig in mail, but even though I am following the instructions for the USB jig the counter is still not going back to 0 :/
This is the instruction I followed: take battery out for like a minute -> put the battery in but don't turn phone on -> put the usb jig in -> it's supposed to boot up with 0 flash count?
Mine still says 4... Can anyone please help?
sfoksn said:
Hi, I'm having an exactly same problem with you and I just got a USB jig in mail, but even though I am following the instructions for the USB jig the counter is still not going back to 0 :/
This is the instruction I followed: take battery out for like a minute -> put the battery in but don't turn phone on -> put the usb jig in -> it's supposed to boot up with 0 flash count?
Mine still says 4... Can anyone please help?
Click to expand...
Click to collapse
Is yours a i9100? If so is your firmware the latest 2.3.5 KI3 or KI8?
Could be your device has the new bootloader. If so check intratechs original firmware thread in original development section and install his old bootloader via Odin. Have a read while your there to get the latest info.
Good luck
Sent from my GT-I9100 using XDA App
aceofclubs said:
Is yours a i9100? If so is your firmware the latest 2.3.5 KI3 or KI8?
Could be your device has the new bootloader. If so check intratechs original firmware thread in original development section and install his old bootloader via Odin. Have a read while your there to get the latest info.
Good luck
Sent from my GT-I9100 using XDA App
Click to expand...
Click to collapse
Yeah, I got stuck while flashing 2.3.5 Gingerbread... Yeah I think it has a new bootloader, as I remember Odin updating the bootloader section before messing up.
Is there any way I can get the USB jig to work? My phone is no longer recognized by the USB anymore so I can't even flash another bootloader or anything.
Is there anythign I could do to make the USB jig work without connecting it to the computer?
Can you get into download mode using the buttons?
Volume down+home+power
If so try and flash another Rom from intratechs thread to get back to stock.
If that works you can try again.
Sent from my GT-I9100 using XDA App
Early yesterday I launched Kies and hit the update firmware option from the tools menu to see if the alleged ICS update was available for my phone. It appeared it was with, a message promoting that it would clear all personal data from the phone, which I then selected cancel so I could do a backup of pictures/videos on the phones internal SD.
Without doing any sort of backup yet I shutdown the phone, only for it to freeze on the shutting down screen. After 20 mins I pulled the battery and let the phone cool down since it had gotten warm trying to shut itself down. After replacing the battery and turning on it was stuck in a bootloop with only the SGS2 logo, never reaching the ATT logo.
At that point I came to XDA, which I frequently browse but have yet to root, and began reading and searching everything I could find.
Hours later I decided to attempt to flash the stock firmware from sammobile.com using Odin. The flash took a long time and I assume never completed. I left it overnight since I didnt want to unplug it mid-flash. Checking back in the morning the phone is black, Odin says failed/disconnected, and I find the battery completely drained. I charged it for a while then tried turning it back on and got the yellow triangle "firmware upgrade encountered an issue..." screen.
Now i'm attempting once more to flash the firmware but again it has been 30 mins on Sbl.bin. I've had a hard time finding stock firmware in different varieties with working links, so to not increase the flash counter in the event I ultimately have to send it in for repair.
Any suggestions on where to go from here? I've followed every direction I can find for flashing stock firmware and nothing has been successful.
Glad to help if I can. Please tell me exactly what package you flashed from sammobile, with a link if possible.
You should change the title of the thread.... I killed my phone. LOL!
http://forum.xda-developers.com/showthread.php?t=1313659
I attempted to flash I777UCKH7, 2011 August, USA (AT&T)
w.sammobile.com/firmware/?page=3&t=1&o=1&m=SGH-I777&r=-1#modelsa
BROKKANIC:
I've tried the steps in that thread, the One-click Oden does not have the phone showing up in any boxes, yet it still shows up in the non-One click Oden.
nett3 said:
I attempted to flash I777UCKH7, 2011 August, USA (AT&T)
w.sammobile.com/firmware/?page=3&t=1&o=1&m=SGH-I777&r=-1#modelsa
BROKKANIC:
I've tried the steps in that thread, the One-click Oden does not have the phone showing up in any boxes, yet it still shows up in the non-One click Oden.
Click to expand...
Click to collapse
Try this.....
2c.) How to root by flashing Entropy512's Return/Unbrick to Stock, Kernel + Rooted System Package with Modem using Odin3 One-Click Downloader (Windows)
Download the "Odin3 One-Click Downloader Stock I-777 UCKH7 with Root no BL" package from Hotfile. Extract the contents of the zip file to a directory on your hard disk drive. This is a One-Click version of Entropy512's Return/Unbrick to Stock, Kernel + Rooted System Package plus stock modem from the development forum. (Contains stock zImage, factoryfs.img with root, and modem.bin.)
Start the Odin3 One-Click Downloader program by double clicking on "I777UCKH7 OCD With Root.exe".
Now Enter Download Mode:
With the phone powered off, plug in the usb cable while holding the vol up + vol down buttons (but not the power button).
When the warning screen appears, press Volume up to continue into download mode.
In Odin, the small edit box in the upper left corner will turn yellow, and say something like [0:COM8]. The number could be different.
Click Start. Watch the progress bar advance in green while the message box in the lower area describes the steps. When the flash is finished, the top left larger edit box will turn green and say PASS! and your phone will automatically reboot.
Unplug the usb cable from you phone after it boots up. Success. You're Rooted.
SOURCE: http://forum.xda-developers.com/showthread.php?t=1311081
creepyncrawly would know better. It's his thread.
Download the file from below post to go back to stock I777UCKH7. Follow the instruction written in the post. I just had the same a while ago using the mobile odin to go back to stock. Got stuck on Samsung Galaxy SII screen. Pulled the battery and then followed the instructions from this post. I selected the one that says no BL 'I777UCKH7 OCD No BL'.
http://forum.xda-developers.com/showpost.php?p=18859438&postcount=199
Once you are done with the stock restore. To upgrade to ICS LE5 follow the instructions from below post. Make sure you read and follow the instructions as mentioned in the post.
http://forum.xda-developers.com/showpost.php?p=27707563&postcount=83
nett3 said:
I attempted to flash I777UCKH7, 2011 August, USA (AT&T)
w.sammobile.com/firmware/?page=3&t=1&o=1&m=SGH-I777&r=-1#modelsa
BROKKANIC:
I've tried the steps in that thread, the One-click Oden does not have the phone showing up in any boxes, yet it still shows up in the non-One click Oden.
Click to expand...
Click to collapse
You downloaded I777UCKH7_I777ATTKH7_ATT and extracted I777UCKH7-rev02-home-low-cl503881.tar.md5?
Flashed the .tar.md5 in the pda slot?
What version of Odin are you using?
Edit: You're getting lots of advice here. Let me know if you need me to help troubleshoot your issues.
BROKKANIC/krips2003: Thanks for helping so far, but no luck. Those both link to the same Odin One click. This and another one click I tried do not show the phone connected to any COM#. But, in the non-one click Oden the phone shows up. I have pulled the battery and changed USB ports and it still will not show up in the one click.
In the mean time I'll see if there's a solution for that, but I'd like to hear any other suggestions.
Edit: I get the feeling Odin is not starting the write process, since neither the progress bar or words show up in the box above COM# until AFTER I unplug the phone, at which time it flashing quickly then displays Failed.
nett3 said:
BROKKANIC/krips2003: Thanks for helping so far, but no luck. Those both link to the same Odin One click. This and another one click I tried do not show the phone connected to any COM#. But, in the non-one click Oden the phone shows up. I have pulled the battery and changed USB ports and it still will not show up in the one click.
In the mean time I'll see if there's a solution for that, but I'd like to hear any other suggestions.
Edit: I get the feeling Odin is not starting the write process, since neither the progress bar or words show up in the box above COM# until AFTER I unplug the phone, at which time it flashing quickly then displays Failed.
Click to expand...
Click to collapse
Try using another micro usb wire if you have one. If not then get one from radioshack or bestbuy. I had the almost similar issue on my captivate with the original USB cable. Then I got a Rocketfish one from bestbuy and it worked like a charm.
I'm sure you might have already done this. Make sure you first run the ODIN and then put your phone in download mode.
krips your a genius!
The one click is now working thanks to the suggestion to pay attention to order of operations. I must have never plugged the phone in AFTER starting the one click. This was easily overlooked when I've been switching the phone between 2 PCs and 3 micro usb cables.
I now have a progress bar and have had made more progress than in the last 24 hours. Even after searching I did not find this solution, even though it's stated in the directions and it seems trivial, maybe it should be emphasized the one click needs to phone plugged in after it's running.
Thanks again. I'll update this post when it's back to being a phone again.
PS. BROKKANIC: you were right, if I didn't kill my phone then I sure was the impeding factor in its recovery.
Good news/bad news. Still stuck in bootloop, but now have SGS2 logo instead of yellow triangle. Trying to enter recovery mode crashes the phone soon after it appears.
Is this a bootloader problem, kernel problem, or something else?
LOL!. Glad you got it working.
nett3 said:
Good news/bad news. Still stuck in bootloop, but now have SGS2 logo instead of yellow triangle. Trying to enter recovery mode crashes the phone soon after it appears.
Click to expand...
Click to collapse
Flash back to stock first.
BROKKANIC said:
LOL!. Glad you got it working.
Flash back to stock first.
Click to expand...
Click to collapse
I believe that what I have been doing. I ran I777UCKH7 OCD With Root.exe, which resulted in bootloop, then ran I777UCKH7-CL503881-No-BL.exe, which also resulted in bootloop. Both completed successfully, but resulted in the same bootloop.
Odin appears unable to flash anything without it being a one click. I'm trying to flash Siyah-v2.6.14-att.tar. But Odin hangs at zImage with no progress bar.
What operating system you using: if windows 7 are you running as administrator ?
hd779 said:
What operating system you using: if windows 7 are you running as administrator ?
Click to expand...
Click to collapse
I've resorted to my WinXP laptop which has been more successful than my Win7 desktop. On the Win7 attempts everything is run as admin, but has many time bluescreened and hard reset the whole PC when attempting to flash anything with Odin. Maybe a separate issue, maybe not. But the XP machine is atleast successfully flashing the Odin one clicks.
Update: Odin standalone (non-one click) appears to be unable to flash anything, it will only hang when trying to write. One click Oden packages seem to work. Is there a one click with full stock sbl, param, kernel, etc?
I think your problem is you flash to stock with packet include bootloader, so that is the reason why your phone is brick.
I'm using this: http://forum.xda-developers.com/showthread.php?t=1691659 for stock UCKH7. This is non-root version and work very well for me. It include sbl, kernel and param, ...
gefox4vn said:
I think your problem is you flash to stock with packet include bootloader, so that is the reason why your phone is brick.
I'm using this: http://forum.xda-developers.com/showthread.php?t=1691659 for stock UCKH7. This is non-root version and work very well for me. It include sbl, kernel and param, ...
Click to expand...
Click to collapse
I haven't flashed a package with a bootloader yet. The only ones that work for me are Odin one click packages, and the two I've tried do not have bootloaders. I've been looking for one WITH a bootloader but no such luck yet, since maybe that would solve the problem.
The guide/link you've suggested will not work for me at this time. I do not have the ability to boot into any andriod OS. The only capability my phone has is executing Odin one click packages for some reason, even Oden standalone firmware flashes do not work.
I had a similar issue...I eventually got mine stuck at the ATT droplets....
Finally I flashed back to 2.3.4 stock....did the ota...then upgraded to ICS.
Its all on my work laptop so I wont be able to post any specific files or their names until monday...
Good luck!
Once your phone gets to the boot screen try to get into stock 3e (both volume buttons + power till 2nd SGSII splash screen) recovery and do a factory reset. Should boot after that. Good luck.
Sent from my SAMSUNG-SGH-I777 using xda premium
Why not try a custom ics rom? What else do you have to lose? Staying stock is overrated anyways. You may also have an antivirus stopping Odin but I doubt it. Just turn off your antivirus and try.
Sent from my SGH-I777 using xda premium
edit: sorry forgot to put [Q] in title... a little stressed
Hi. Normally I wouldn't post a new thread for a common flashing problem but I'm really stuck here. I've been flashing for 5+ years and have never been this deep in crap before.
First of all after trying almost every rom I was on PARANOIDANDROID and I decided to go back to stock Bell UGDL3 firmware from samfirmware. Got everything ready Downloaded ODIN, started her up put the .tar.md5 file into the PDA section. Did not tick or untick any box. Plugged in the phone and started flashing.. then the phone hung on the factoryfs part of the flash and windows crashed (I was using win8 pre release bootcamped on a mac). So I thought that's weird. Tried it again and same thing. So I went to the GF's Win7 laptop, redownloaded everything and tried again. It too got stuck on the factoryfs part and then said failed. So then I had a phone that failed halfway through a flash.. no biggie happened before. I could still get into download mode. Went home and I had ODIN plus an old LPQ firmware on that so I tried flashing that. It just said failed to write, right away. Now after unplugging and plugging in the download mode so many times every computer I plug my phone into just says my device is not recognized. So now I'm thinking (but hoping that I haven't) messed up download mode? I also can't get into recovery as it just comes up with the screen "Firmware upgrade encountered an issue. Please select recovery mode in Kies and try again". Well Kies won't recognize my phone either... I'm a little worried that I've done some real harm...
i believe i had an similar problem with my i9000,
can you get into recovery mode?
No I cant
Sent from my HTC Legend using xda premium
I've searched for hours for different solutions and have tried them all. I'm on my last leg, and I can't wrap my head around what is going on.
I'm running an S2 with ShoStock3 rom. It's been rooted for over a year now without any major hiccups at all. Last night, it froze on me. Usually when it does this, I just force-restart by holding the power button down until it cycles. Phone usually boots right back up, and I'm all set. This time it just stayed on the boot screen. For eternity. I let it sit like that for more than 45 min, and it never budged. Turn it off from the booth screen, it'll boot right back up. I can go into download mode, but not recovery, and every little trick I've tried works.
I've tried flashing new kernels with ODIN. Tried various recoveries, like Philz and even went as far as the one touch factory ROM and using the regular method for getting the stock ROM. Nothing. Maybe I'm doing something wrong. Most people who have this problem only recently added a new ROM or modified something. I haven't touched the ROM, kernel, etc. for over a year before this happened.
ODIN never makes it far when trying to flash anything. It depends on what is being flashed. It never gets past nand read/write. It never gets past boot.bin. It never gets past factory.img. Etc. Etc. I don't know if maybe something isn't going through between computer and phone, and that's why I'm not having success or what in the world is going on. Every tutorial or help I found confidently stated that all you have to do is flash this kernel, go to recovery, clear cache, and you're all set. But I feel like I'm the odd man out.
I'm afraid that this won't see much attentions, as the S2 is far from new, but like I said I am on my last leg. I just don't understand how it stops working from cycling power. I also don't understand how every attempt doesn't even scratch the surface. Any and all help will be greatly appreciated
The most basic step is to verify you're using the correct button combo to get into recovery: power+both volume keys, then release after the second Samsung logo.
SteveMurphy said:
The most basic step is to verify you're using the correct button combo to get into recovery: power+both volume keys, then release after the second Samsung logo.
Click to expand...
Click to collapse
^^ while the device is NOT USB connected to a computer.
Actually, you're lucky. This device is so popular, even though is it getting old, that there are still a handful of knowledgeable people hanging around.
You need to get into recovery. As Steve and Cyril have said, try the correct button combination, and post back here to verify that you are using the correct combo and that it will not go into recovery.
If you do get into recovery, perform a wipe data/factory reset and see if that gets your phone to boot into the system.
If you are unable to get into the recovery with the correct combo, then you may have one of several possible issues. The first possibility to troubleshoot is nand read/write corruption. Do the following:
Instructions to clear nand read/write corruption. Instructions are specific; do them in order, and don't skip.
Odin3 v1.85 is recommended.
1) Download the SBL Bootloader from the Download Repository. Flash it as PDA in ODIN, without ticking Re-Partitioning. (Please observe normal bootloader flashing caution.)
2) Download the Tar version of Siyah 2.6.14 Kernel. Flash it in PDA. Without ticking Re-Partitioning
3) Flash the Tar.md5 of the full stock Gingerbread distribution from the Download Repository, I777UCKH7 including the bootloaders and everything, in the PDA slot.
I have done the correct button combination for recovery, I promise you that. It brings up Samsung logo first, cuts off, and brings it up a second time, but releasing does nothing. I've tried it several times with different delays as well.
creepyncrawly said:
Instructions to clear nand read/write corruption. Instructions are specific; do them in order, and don't skip.
Odin3 v1.85 is recommended.
1) Download the SBL Bootloader from the Download Repository. Flash it as PDA in ODIN, without ticking Re-Partitioning. (Please observe normal bootloader flashing caution.)
2) Download the Tar version of Siyah 2.6.14 Kernel. Flash it in PDA. Without ticking Re-Partitioning
3) Flash the Tar.md5 of the full stock Gingerbread distribution from the Download Repository, I777UCKH7 including the bootloaders and everything, in the PDA slot.
Click to expand...
Click to collapse
I've actually tried this. On step one, it hangs up on "NAND Write Start!!", just like everything else that tries to get flashed.
To clarify, I should be flashing the I777 UCKH7 sbl.tar file, correct?
Luckily for me I qualified for a free upgrade from ATT for an S4, but I don't want to give up on this phone just yet. Especially with all of the data I have yet to recover from it.
XxArxAngelxX said:
I have done the correct button combination for recovery, I promise you that. It brings up Samsung logo first, cuts off, and brings it up a second time, but releasing does nothing. I've tried it several times with different delays as well.
I've actually tried this. On step one, it hangs up on "NAND Write Start!!", just like everything else that tries to get flashed.
To clarify, I should be flashing the I777 UCKH7 sbl.tar file, correct?
Luckily for me I qualified for a free upgrade from ATT for an S4, but I don't want to give up on this phone just yet. Especially with all of the data I have yet to recover from it.
Click to expand...
Click to collapse
Yes, that is the correct secondary boot loader.
Next, you must assume that there is a connection problem between the phone and the computer. The micro usb port, the cable, the usb port on the computer and the computer itself are all possible weak links in the connection. So try different cables, different ports on the computer, escpecially one directly connected to the mother board, even try a different computer. You can not proceed until you can get the phone to receive a flash and pass. A few people have even reported that they finally were able to complete a flash just by trying repeatedly over and over until it finally passed.
creepyncrawly said:
Yes, that is the correct secondary boot loader.
Next, you must assume that there is a connection problem between the phone and the computer. The micro usb port, the cable, the usb port on the computer and the computer itself are all possible weak links in the connection. So try different cables, different ports on the computer, escpecially one directly connected to the mother board, even try a different computer. You can not proceed until you can get the phone to receive a flash and pass. A few people have even reported that they finally were able to complete a flash just by trying repeatedly over and over until it finally passed.
Click to expand...
Click to collapse
Tried using different computer. Brand new cord. Multiple times tried. Different ports. I dunno, it's doing the same thing. It stops whenever it gets to NAND Write Start.
EDIT: Tried something I saw in another thread. Used stock binary with pit file. Never finished, so aborted it. Now phone doesn't come on at all for any reason whatsoever. -.- Pretty sure I fried it
Hello All!
My first post here, even though I have long been a lurker. I hope I'm posting in the right place. If not, apologies, and Mods - please redirect me, and I shall re-post in the correct place.
Phone: SAMSUNG GALAXY S3 GT-I9300 International version
Last known installed/running OS: Official SAMSUNG JB ROM (Unsure WHICH version) after having run on CM 4.4 for a couple of weeks.
PROBLEM:
a few months after going back to stock, Phone suddenly developed issues of random reboots. These would happen at any point in time, with no predictability whatsoever. One fine day, it rebooted, and wouldn't get past the Samsung splash screen. Pulling the battery and trying to restart phone resulted in the same stuck at Samsung logo issue.
Left the phone alone for a couple of months after this as I had a spare, but finally decided to try and revive the S3.
Phone does not charge when connected to charger. At least, it shows no visible signs of it. It DOES, however, try booting itself when plugged in, but gets stuck on the first screen of ODIN Download mode, instead of the Samsung logo splash screen as it used to earlier. Also note that this screen it gets stuck on is a pixellated screen, not the clear normally seen screen when entering ODIN mode.
The Vol UP, Home and power button combo brings me to this very same screen, there is no recovery menu to be seen, as would be normally. The Vol DOWN, Home and power button combo brings me to the regular clear ODIN mode as usual.
The headings at this screen read:
ODIN MODE
PRODUCT NAME: GT-I9300
CUSTOM BINARY DOWNLOAD: No
CURRENT BINARY: Samsung Official
SYSTEM STATUS: Custom
I have read through most posts regarding similar issues on XDA as well as other forums, and tried flashing stock firmwares (single AND multiple part ones) through ODIN, with no success. The error i always get is as in the attached screen captures.
I've tried ALL versions of ODIN, and many PIT files. All were failures.
So, is this a dead for all purposes phone, or do I still have hope since ODIN mode is still available?
I don't think USB debugging was checked before bricking, because ADB toolkits just keep waiting for phone to be detected.
All drivers are up to date and installed correctly. Kies is not installed.
Any help is welcome.
@Mohanms04: if you flash a 3part-PIT, what result views ODIN after finishing?
I have a Device here which seems to have the same or at least a similar problem, however, i got it for free from someone else to experiment with, so there is no urgent need to repeir it.
I tried flashing a pit and erasing nand, but when i start to do it, odin just gets stuck at "erasing", if i try to flash a full firmware it just hangs at "getting pit for mapping" so i assume the nand is gone for good... however, i have one more dead s3 arround that seems to have a burned cpu, probably i manage to solder over the nand or the cpu
rp158 said:
@Mohanms04: if you flash a 3part-PIT, what result views ODIN after finishing?
Click to expand...
Click to collapse
ODIN stays at "Setup Connection" without any progress. I've left it overnight a few times, just to ensure I was giving it enough time.
When the cable is pulled, it reads "there is no pit partition"
@Mohanms04: I suppose, it's hardbricked
rp158 said:
@Mohanms04: I suppose, it's hardbricked
Click to expand...
Click to collapse
Aargh.. was afraid of that. Well, guess its JTAG to try next, and then paperweight if that dont fix it.
Thanks anyways!!
Mohanms04 said:
Aargh.. was afraid of that. Well, guess its JTAG to try next, and then paperweight if that dont fix it.
Thanks anyways!!
Click to expand...
Click to collapse
Try this recovery firmware, if not the jtag is required.
http://forum.xda-developers.com/showpost.php?p=30087735