I was updating to FreeX10 2.2 Beta 4 .. Flashed the new FW .435 from stock RoM thread.
Well, here is my predicament. I can't get any further then the Sony Ericson logo. I have tried entering xRecovery to no success.
I was running Blue Sparks custom RoM before I attempted this.
Before Blue Sparks I was running Z's first beta of 2.2 and had no problems with installing and using it, I just reverted back to 2.1 because of the amount of bugs "no offense it was just Beta 1 ".
I am just trying to get my phone back up and running and am having an extreme problem of not being able to access anything to do so.
SEUS will not detect the phone under flash mode. Flash Tool will not connect. I have taken SIM Card and SD Card out, left the battery out now for over an hour and still nothing.
Any information on what to do would be greatly appreciated.
PS, I know this is completely in the wrong thread but seeing as how I never posted anythign before or ever had any problems my post count is not high enough to respond to anything under the Development Tab .. I just read everything you devs post and follow instructions.
Xperia X10a
Blue Sparks
Mod: xKrisx
had the same problem, some themes are not ready for the newest fw
check for updates on the threads or install a fw using any flash tool
The problem is not the custom rom. Blue Sparks ran on 2.0.2.A.0.24. To update to the current Beta 4 of FreeX10 2.2 I needed to upgrade my build to the current one, .435.
So with updating, I flashed X10a_2_1_A_0_435_GLOBAL and updated the Base Band by flashing the amss file for it.
After completing the above two steps, I was no longer running Blue Sparks. It was a generic version of .435.
Now is were my problems began. I placed both zip files on my SD Card " Beta4 and gapps" and flashed both through xrecovery.
My phone rebooted and now it gets hung on the Sony Ericson logo during boot up and will not go anyfurther. I cannot access Xrecovery / I cannot enter Flash Mode. I am losted and have no idea of what to do to restore my phone.
Happend to me to because i flashed beta 4 and then gapps right after. I found that flashing beta 4 only then reboot phone let it boot then flash gapps after i got phone working. Thats what i did to get it working
EDIT: when se logo comes just rapidly press the back button until xrecovery pops up tryid one time where i was clicking for more than 30 sec before it came up
Sent from my X10i using XDA App
@****nab
Thats my problem though, I cannot get into Xrecovery.. It stays hung at Sony Ericson logo period. It has sat there for the better part of an hour to no avail. I tried to connect back to SEUS and just retore back to default but I cannot get the phone into Flash mode either.
I took the phone back to At&t and I think my 5 year old son has more knowledge then they do, it was ****in pointless..
Step one:
turn phone on
step two:
Screen never illuminates
step three :
you can see a monochrome outline of the Sony Ericson logo
step four :
Screen illuminates and Sony Ericson logo is clear visable.
step five :
there isn't one cause it never goes any further then this.
________________________
when trying to enter flash mode
Step one ..
hold down back button
step two .
insert usb cord
step three
wait for green light to stay on.
step four .
Green light flashes three times and phone turns back off..
___________________________________________
Can someone just tell me that I have royaly ****ed my phone up so I can just go throw it in the toilet and clame insurance on it ?
Leave USB cale plugged both ends, remove battery, while holding back button reinsert battery. Should now be in flash mode.
try flashing from older flash tool where a connect button appears.
click connect..insert d cable with back key pressed and click on ok..
or
try getting in flash mode using seus..
if both doesnt work there must be problem with back button i guess..
(remember to install gordongate driver from flashtool/driver)..
and if u succeed in getting in flash mode then upadate d whole firmware to .435..not just d baseband..
then format system,cache,data thru xrecovery and install b4.
all d best.
have the same exact issue, but mine was due to using format/system option in xrecovery i press on it by mistake thinking it was the option above it..... i am lost with a beatiful xperia x10 not working past sony ericsson logo like you..........anyone to our rescue????? ill sure buy them a beer!
sAnDrOmAn said:
have the same exact issue, but mine was due to using format/system option in xrecovery i press on it by mistake thinking it was the option above it..... i am lost with a beatiful xperia x10 not working past sony ericsson logo like you..........anyone to our rescue????? ill sure buy them a beer!
Click to expand...
Click to collapse
just flash it with seus.
Related
Anyone know what I need to do to fix this? Phone doesn't boot up past the sony ericsson screen and seus/pc companion will connect but won't flash the global generic 2.1 and I can't get flashtool 2.9.1 to flash the x10 generic 2.1.A.0.435 either? I updated Wolfbreaks CM 6.1.3 V05 + update V054 to his new V06 update. I got alot of force closes so i attempted to wipe everything and flash Generic 2.1.A.0435 so after that i did reboot flashed Wolfbreaks V05 + update V06 and reboot, restored apps and data using MyBackup + root and Titanium + root then started having force closes again so i thought i would forget this update and go back to V05 + update 054 since it works great. that is when i did a reboot to enter Xrecovery but the phone wouldn't enter Xrecovery and is now stuck on the sony ericsson boot screen. The only way to turn it off is to pull the battery. I haven't seen any red led lights on the phone at all. Anyone have any advice? I'm stuck. if any needs more info just ask.
Btw is this what "soft bricking" a X10 is? that's what i was told.
guys I was able to finally get my phone to stay in flash mode long enough to prepare my X10 using SEUS after trying about 50 times. It didn't completely finish the update/flashing of Global 2.1 before giving me a error but i believe that the "preparing stage" was able to help get the phone to stay in flash mode longer because the green light wouldn't stay on very long. So i was beginning to think i had a bad usb jack on the phone, luckily that wasn't it. I also tried Flashtool 2.9.1 with no success. I then got the idea to try my the older 2.6 flashtool that i still had on my computer and to my surprise it worked. I was able to flash generic 2.1.A.0.435 firmware, root, optimize and Xrecovery. I talked to The Gingerbread Man and he directed me to his X10 guide which is where i got the idea to try the 2.6 flashtool. Oh and I am pretty sure what i did wrong was restoring data after flashing the V06 update. Wolfbreak specifically states NOT to restore data ONLY apps which i didn't see at first. Hope this helps anyone that has experienced these symptoms because i didn't find any posts of my exact situation when i was searching for answers.
Rollhard said:
Anyone know what need to do to fix this? Phone doesn't boot up past the sony ericsson screen and seus/pc companion will connect but won't flash the global generic 2.1 and I can't get flashtool 2.9.1 to flash the x10 generic 2.1.A.0.435 either? I updated Wolfbreaks CM 6.1.3 V05 + update V054 to his new V06 update. I got alot of force closes so i attempted to wipe everything and flash Generic 2.1.A.0435 so after that i did reboot flashed Wolfbreaks V05 + update V06 and reboot, restored apps and data using MyBackup + root and Titanium + root then started having force closes again so i thought i would forget this update and go back to V05 + update 054 since it works great. that is when i did a reboot to enter Xrecovery but the phone wouldn't enter Xrecovery and is now stuck on the sony ericsson boot screen. The only way to turn it off is to pull the battery. I haven't seen any red led lights on the phone at all. Anyone have any advice? I'm stuck. if any needs more info just ask.
Btw is this what "soft bricking" a X10 is? that's what i was told.
Click to expand...
Click to collapse
dude chill out, our beloved x10 is unbrickable till date..!!
make sure you have prover usb drivers for x10 to be recognized by flashtool!!
if yes make sure you're entering the flash mode correctly..!!
ok. Question. I have the same problem, my X10 had the new CM7 k005 on it. then I tried to flash back to bb 49 to put Trips 2.3.3 on it. flashed the back to stock kernel. NOW. all I get is re-boot re-boot, finally all it does is stay on the se screen with no love at all from seus??? And it wont go into xrecovery at ALL
HEEEEELLLPPP MMMEEEEEEEEEEE
Seus picks up the in flash mode.
Get Seus ready "select your phone.."
Just switch off your phone.
Hold "back" & Plug in the usb into the phone at the same time.
A green LED should show.
Then after it has flashed the phone might act a bit "glitchy" just give it a few hours to settle the Baseband.
isnt there already a million topics about people bricking x10s, its impossible the x10 cannot be bricked....search the forum
yeah there is but this was the first one I found to hijack!! anyway, I had to keep prssing update about ten times on seus before it got sick of me and gave me another option of which phone I was trying to repair!! thats how bad I had it stuffed up.
Anyhoo, a while later and it is all good!!
hi guys. my x10 froze at se boot and does nothing. i've read through almost all helpfull threads that are similar to my problem but the problem still persist. fyi, i booted to xrecovery, made a backup and i noticed that there were problems in backing up (md5 chcksum, i think). but the backup file was created. i restored using that file and now it is stuck at boot. i can't even turn the phone off. i've tried hard reset, tried using the sues, flashtoo and even pc tools but to no avail. this is due to the phone can't connect to usb. can anyone please help me.
You have do a factory reset and wipe cache?
how can i do that andres3d? are there any way for me to do that? i'm trying but the phone just can't go past the se boot. it's just stuck there. i can't even turn the phone off. the only way is to take out the battery.
Try this, enter into xrecovery and select "factory resect" first at all, then reboot.
I got stuck there too, and I haven't the xRec installed
You can download the SE Update Service (SEUS) and flash the original rom back to it.
Download the software and install, take off the battery, wait a little bit (30s or so), insert the battery back. DO NOT TURN ON THE PHONE YET.
Open the SEUS, choose the phone (X10) and click 'go', or 'ok', or whatever. Keep going and the software will tell you to plug the phone. Plug the phone turned off. When it's plugged, turn it on holding the back button until the software tells you to release.
Wait a few moments... and it's done. Turn on your phone, it should take a little longer to boot, but it's just the first time, then it boots normally.
It's quite easy to do when you know what to do
thanks in advance but i've tried both method and it still got me nowhere. first, i can't boot to xrecovery at all and second, the sues doesn't even detect my phone.
Did you try download a stock firmware from here and install by flashtool?
Do you have installed drivers from x10 to your PC?
I thing the only way is by flashtool, because you don't have xrecovery access l.
http://forum.xda-developers.com/showthread.php?t=872298
Sent from my X10 using XDA App
rota2903 said:
thanks in advance but i've tried both method and it still got me nowhere. first, i can't boot to xrecovery at all and second, the sues doesn't even detect my phone.
Click to expand...
Click to collapse
Your phone must be charged ¬¬
Leave him charging at wall for about 45-60min and then try to do the step-by-step
tnx
tnx guys. i'll try the methods that u guys suggested. i really hope that i don't have to send the phone back to the shop.
OMG. it was actually my cable!!! that's why i can't flash my phone. now the phone is back to it's original state. anyways, i would like to thank all of you guys that have given me great advice. thanks again guys.
[Q] {HELP} another x10 stuck at se boot part 2
rota2903 said:
OMG. it was actually my cable!!! that's why i can't flash my phone. now the phone is back to it's original state. anyways, i would like to thank all of you guys that have given me great advice. thanks again guys.
Click to expand...
Click to collapse
Hi all
Unfortunetly my case is 99% similiar as "Sony Ericsson XPERIA X10XPERIA X10 Q&A[Q] {HELP} another x10 stuck at se boot" but changing the cables doesn't help. The only thing which the phone respond is to hold back starting of booting what immidietly happening when i'm connecting the usb cable.
I had xrecover installed before but is not starting onto flashing mode.
Any ideas
Hi everyone
yesterday I bought a X10 (it wasn't brand new)
I turned it on and it asked me for settings (language, time, etc) (yeah it's not new but they changed the rom before sell it to me)
I worked with it for like 10-15min and I got a big vibrate and it turned off. I pluged it into the charger, there was an orange led for 5min and then nothing, when I tried to turn the phone on I saw SE logo and it restarted. I plugged it to the charger, nothing again, not even orange led
I took it to a store and they shocked the battery, i came back, turned it on, it booted ok everything was fine,I plugged it again to full charge. orange led for 1.5h and then green led.I worked with it a short time then turned it off to put the sim and sd card in
when I turned it on it booted till lock screen and rebooted. again SE logo then boot again
it sometimes boot till lock screen sometimes only se logo and reboot
when it goes to lock screen I see antena has red x on it, i thought maybe that's the problem, i removed sim and sd, still the same
Please please please help me
ps 1: I can't connect it to the pc, I tried but when pc wants to recognize it and install drivers, it stops and says "not successful"
Have a look in the dev section for flashtool (there's a tutorial in the q&a section), look in the firmwares sticky in the dev section and download the firmware for your region. I suggest you pick a generic firmware. Now use flashtool to flash the firmware to the phone.
This should solve the problem.
thank you Frosty for fast answer
but my problem is my pc dosen't recognize the phone
flashtool works even without drivers?
Flashtool works in flash mode. If you can't get your computer to recognise the phone when it is powered on, it should still recognise it in flash mode. If not, there is an option in flashtool to install the drivers.
Sent from my x10, rocking Wolf's 2.3.3 + DooMKernel, overclocked to 1.2 GHz...
good, so I think I still have a chance to fix it
btw, now I have stock 2.3.3 installed
which rom do you recommend? should I install 2.3.3 again or downgrade to 2.1?
I want it to support farsi
X10i_3.0.1.G.0.75_CUSTOMIZEDARO-ARO GENERIC 1241-1846
is right?
You could do 2.3.3 or 2.1. It shouldn't matter.
As for Farsi support, 2.1 supports more languages than 2.3.3 I think. I just checked the list of available languages on my 2.3.3 ROM and Farsi isn't listed. 2.1 might support it.
You could always try both to see which one better suits your needs.
That firmware you have is 2.3.3, by the way.
thank you so much frosty
I asked if i could install 2.3.3 because now have 2.3.3 and i have this problem. installing same version will fix it?
and one question about baseband
should i download one or it comes in firmware pack/zip
if I have to download it, how do I know which one?
Your're welcome.
Oh, in that case, you should be fine.
The baseband is included in the firmware file.
I'm facing a weird problem
I can't turn my phone on, I've been told to try flashtool and install a new rom
my old rom was 2.3.3
I downloaded flashtool and X10i_3.0.1.G.0.75_CUSTOMIZEDARO-ARO GENERIC 1241-1846
first time I tried instrudoction in second post in this topic. it seems flashtool recognized my device and startet flashing but after a few min it said flash aborted
I wanted to try again but this time even before i connect the device to usb cable, flashtool say flashing start and nothing happen
I also tried SE update service, it downloaded the rom and it seem it worked (second green bar went to the end and said disconnect phone and restart)
I restart the phone but it reset after SE logo, sometime it boot till lock screen and reset again
Please help me
Sorry to say this, but you might be out of luck.
If re-flashing stock couldn't fix it, your issue may be a hardware problem.
Do you have any sort of warranty? If it's second hand, you probably don't.
You could try taking it to a Sony Ericsson service center and see if they can do anything.
omg
I'm officially beeeeeep
thanks anyway Frosty
btw, pc campanion and se update service do something different
is it possible that pc companion can fix it?
Well you could try. Couldn't hurt.
Hi guys!
I have some problems with my X10i. First it all started with me wanted to go back to a previous backup with xRecovery. All this went wrong and got a message in xrecovery that it was not able to load sd-card. And then it was stuck on Sony Ericsson boot screen.
I got it flashed now, with Android 2.3, and wanted to root and install xRecovery, but when I start my phone and connect it to my comuter, it reboots. It wont stay on with USB connected to PC, so long till I can root.
I'm getting pretty irritated now.
What is wrong?
Hope you guys can help, and sorry for bad english.
Revert back to stock f/w pal u should be fine
Sent from my X10 using XDA
Thank you for your answer.
But do you mean to restore to 2.1? When I downloaded flashtool I got 2.1 with the program, do you mean to restore with this flash that came with flashtool program?
Flash
Try fix it with seus
Okay.. I updated my phone to newest, 2.3.3.
After I had updated the sony program said that I had to wait for my phone to reboot and not take out my battery for the first time, but my phone did not reboot. Nothing happend after I disconnected the phone. When I pressed the power button it only blinked green one time, so I took out my battery and rebooted.
Everything went fine in the beginning, couple of reboots that I expected after new software, but now my phone reboots and reboots. Sometimes I can't even get to the screen where I unlock my phone before it reboots. And even thou when charging, it reboots.
Omg.. so frustrating!!!
Please help! Should I restore to 2.3 or the 2.1 that came with flashtool program?
I have been visiting this site ever since I first read about X10 & was fascinated by it (I have always loved SE phones). Anyway, I have since gotten an X10i (AT&T) & have de-branded it as well as unlocking & rooting it. Here goes:
I installed Champs' Rom (x10sV9-addon) but didn't want all the clutter he had pre-installed. To make a long story short, I went back to Wolf's ROM via Xrecovery but something went wrong. I can no longer boot into Xrecovery & after SonyEricsson logo, screen goes blank, not black/blue just blank. The other problem is, since I can't see the screen, I can't turn on the USB connection so my PC/Flashtool/SEUS can recognize my device so I can fix it. This happened while trying to re-install Wolf's ROM & installing the following zip files via Xrecovery: Bravia_Xloud engine, Xperia S Player, Champ + Bar, x10_gb_stock_wifi_modules. Then I rebooted & I get the blank screen. I know it is on because I can turn the volume all the way down to vibrate. The "home" button still lights up. PLEASE, I need someone's help with this one as I am no expert, just a moderate tinkerer. ANY help/incite would be appreciated. Sorry, I can't even give you any screenshots. Can anyone out there help me out? Thanx in advance.
daRican! said:
I have been visiting this site ever since I first read about X10 & was fascinated by it (I have always loved SE phones). Anyway, I have since gotten an X10i (AT&T) & have de-branded it as well as unlocking & rooting it. Here goes:
I installed Champs' Rom (x10sV9-addon) but didn't want all the clutter he had pre-installed. To make a long story short, I went back to Wolf's ROM via Xrecovery but something went wrong. I can no longer boot into Xrecovery & after SonyEricsson logo, screen goes blank, not black/blue just blank. The other problem is, since I can't see the screen, I can't turn on the USB connection so my PC/Flashtool/SEUS can recognize my device so I can fix it. This happened while trying to re-install Wolf's ROM & installing the following zip files via Xrecovery: Bravia_Xloud engine, Xperia S Player, Champ + Bar, x10_gb_stock_wifi_modules. Then I rebooted & I get the blank screen. I know it is on because I can turn the volume all the way down to vibrate. The "home" button still lights up. PLEASE, I need someone's help with this one as I am no expert, just a moderate tinkerer. ANY help/incite would be appreciated. Sorry, I can't even give you any screenshots. Can anyone out there help me out? Thanx in advance.
Click to expand...
Click to collapse
You said the button still lights up? can you get into recovery? if so just wipe system and install a rom! and try flashing a kernel with flashtool!!!!
RE: Blank Screen After Flashing Custom ROM
Thanx for getting back to me so fast. As I said, the screen is blank. That is, the backlit display works but I can see nothing else. The "Home" button lights up when i press it but the display does nothing. If/When I reboot to try to enter XRecovery, I see the SonyEricsson logo followed by the backlit screen & nothing else. The Volume up/down buttons work as I am able to silence the phone by turning volume all the way down to vibrate. Because I cannot see what's on the display, I cannot turn USB on/off to connect to PC to run SEUS/Flashtool, etc. I.E. I cannot fix the device. Usually I just boot into XRecovery to fix a problem like this but that doesn't work.
x10
hy, install sony update service and repair your phone, then install again custom rom, the indications how to repair your phone software is in the program.
Best regards
Does USB need to be On or Off on the device for Update Service to run?
daRican! said:
Does USB need to be On or Off on the device for Update Service to run?
Click to expand...
Click to collapse
Update says I already have the latest Update installed.
Flash 2.3 off line update
Sent from my Xperia X10 using xda premium
daRican! said:
I have been visiting this site ever since I first read about X10 & was fascinated by it (I have always loved SE phones). Anyway, I have since gotten an X10i (AT&T) & have de-branded it as well as unlocking & rooting it. Here goes:
I installed Champs' Rom (x10sV9-addon) but didn't want all the clutter he had pre-installed. To make a long story short, I went back to Wolf's ROM via Xrecovery but something went wrong. I can no longer boot into Xrecovery & after SonyEricsson logo, screen goes blank, not black/blue just blank. The other problem is, since I can't see the screen, I can't turn on the USB connection so my PC/Flashtool/SEUS can recognize my device so I can fix it. This happened while trying to re-install Wolf's ROM & installing the following zip files via Xrecovery: Bravia_Xloud engine, Xperia S Player, Champ + Bar, x10_gb_stock_wifi_modules. Then I rebooted & I get the blank screen. I know it is on because I can turn the volume all the way down to vibrate. The "home" button still lights up. PLEASE, I need someone's help with this one as I am no expert, just a moderate tinkerer. ANY help/incite would be appreciated. Sorry, I can't even give you any screenshots. Can anyone out there help me out? Thanx in advance.
Click to expand...
Click to collapse
seem like u dont have a launcher...install launcher throuh flashtool
lilinbakar said:
seem like u dont have a launcher...install launcher throuh flashtool
Click to expand...
Click to collapse
I wish I had gotten this solution sooner. Not sure if it would have mattered. When trying to use Flashtool I kept getting an error saying my phone was not in "flash mode".
I solved my problem by flashing using Omnius & flashing firmware 'X10i_generic_SE_24_MultiTouch.rar'. This got my phone back but it was only 2.1 so I used 'DooMLoRD_v4_ROOT-zergRush-busybox-su' to get me back to 2.3, but this is where I'm at. I had Wolf's firmware before but right now I have no xRecovery installed. I thought I had rooted my phone but xRecovery isn't installed nor is Busybox.. Any ideas? Thanx in advance...EVERYONE @ XDA-DEVELOPERS rox!
I haven't replied to this post because I'm at my wit's end. I still can't get XRecovery installed & I think I've tried all the methods out there. Maybe my problem is that I restored my phone using Omnius. Flashtool works OK but I can't do anything but Flash on it. My phone is a headache now. It freezes up, crashes & sometimes won't read the SD card. Please help...
Sent from My X10a using XDA Premium
daRican! said:
I haven't replied to this post because I'm at my wit's end. I still can't get XRecovery installed & I think I've tried all the methods out there. Maybe my problem is that I restored my phone using Omnius. Flashtool works OK but I can't do anything but Flash on it. My phone is a headache now. It freezes up, crashes & sometimes won't read the SD card. Please help...
Sent from My X10a using XDA Premium
Click to expand...
Click to collapse
C if u can repair phone using SEUS now. Open the software without connecting phone. N then go to the update part. It should give u a repair option. Then follow those steps. Or else just connect ur phone n then start software. When it tells u ur phone is up to date click on that n then click on "repair". Then use the latest flashtool to root. Recoveries come with kernels so just flash a custom kernel.
Sent from my Xperia X10 using xda app-developers app
Many Thanks, I was finally able to use SEUS; before I could not. I used Flashtool to upgrade/downgrade kernel. However, I still don't have XRecovery installed & I'm not sure how to do this. I can't install XRecovery using Flashtool. Any help would be greatly appreciated. I would really like to install a custom Rom again.
I don't think u need to upgrade or downgrade.. just look for a link to download xrecovery here and follow instructions
Sent from my Xperia X10 using xda app-developers app
I'm Back, Baby!
AdX9170 said:
I don't think u need to upgrade or downgrade.. just look for a link to download xrecovery here and follow instructions
Sent from my Xperia X10 using xda app-developers app
Click to expand...
Click to collapse
I'm not sure how it went down but prior to this, I was unable to use SEUS. No matter what I did, I couldn't repair it. However, since your post, I was able to use SEUS & Flashtool to get back to where I was before I screwed up my X10a. I'm currently running Wolf's Rom (many thanx!!!) & am very satisfied w/all your help homey! You da man!
I noticed you are running ICS on your X10i. Any help so that I may partake of that deliciousness?
daRican! said:
I'm not sure how it went down but prior to this, I was unable to use SEUS. No matter what I did, I couldn't repair it. However, since your post, I was able to use SEUS & Flashtool to get back to where I was before I screwed up my X10a. I'm currently running Wolf's Rom (many thanx!!!) & am very satisfied w/all your help homey! You da man!
I noticed you are running ICS on your X10i. Any help so that I may partake of that deliciousness?
Click to expand...
Click to collapse
Ur welcome i don't think u need help you just flashed a custom ROM.. the procedure for installing ICS is the same. Although it'd be better if you are on stock before installing it.. just look for an ICS ROM that u like (I'm using feralab n it works like a charm).
Get the kernel n ROM.. as usual, put the ROM zip on ur SD card, flash the kernel, install ROM from recovery
Although before installing:
1. In recovery go to mounts n storage
2. Format system data n cache
3. Mount system, data n cache (note that if the mounting is successful the options should change to unmount system, unmount data, unmount cache respectively)
4. Then install ROM
5. The installer is GUI based so it'll guide u really well through the installation
Sent from my Xperia X10 using xda app-developers app
daRican! said:
I have been visiting this site ever since I first read about X10 & was fascinated by it (I have always loved SE phones). Anyway, I have since gotten an X10i (AT&T) & have de-branded it as well as unlocking & rooting it. Here goes:
I installed Champs' Rom (x10sV9-addon) but didn't want all the clutter he had pre-installed. To make a long story short, I went back to Wolf's ROM via Xrecovery but something went wrong. I can no longer boot into Xrecovery & after SonyEricsson logo, screen goes blank, not black/blue just blank. The other problem is, since I can't see the screen, I can't turn on the USB connection so my PC/Flashtool/SEUS can recognize my device so I can fix it. This happened while trying to re-install Wolf's ROM & installing the following zip files via Xrecovery: Bravia_Xloud engine, Xperia S Player, Champ + Bar, x10_gb_stock_wifi_modules. Then I rebooted & I get the blank screen. I know it is on because I can turn the volume all the way down to vibrate. The "home" button still lights up. PLEASE, I need someone's help with this one as I am no expert, just a moderate tinkerer. ANY help/incite would be appreciated. Sorry, I can't even give you any screenshots. Can anyone out there help me out? Thanx in advance.
Click to expand...
Click to collapse
your LCD flexibel not improperly installed or detached, just open your x10 with screwdriver, and plug it in again your LCD flexible socket.
Iam sory if my english bad
Since I flashed my rom.My phone comes on but I can see anything, even when starting I can't see anything...
I really need help..
I will appreciate if you help me sort it out.