Hi, I have install mini CM and my phone is blocked on the boot logo cyanogenmod
Help me please !!!
If you have xrecovery installed and a backup, you can use xrecovery to restore your phone.
If not you can use SEUS or PC-Companion to repair your phone, but you will loose your data.
If your phone doesn't restart open the phone and disconnect your batterie-connector for a short time.
theandroidlover said:
Hi, I have install mini CM and my phone is blocked on the boot logo cyanogenmod
Help me please !!!
Click to expand...
Click to collapse
Boot to xrecovery, do a full wipe, then reboot. Shut down the phone by pulling the battery if you're still in the boot. When that failed, go http://xperiaminicyanogen.wordpress.com/help/bricked/
Divr said:
Boot to xrecovery, do a full wipe, then reboot. Shut down the phone by pulling the battery if you're still in the boot. When that failed, go http://xperiaminicyanogen.wordpress.com/help/bricked/
Click to expand...
Click to collapse
Hello Divr,
You cannot pull off the battery on X10 mini.
In order to restore a bricked mini:
-Launch SEUS (NOT Pc Companion)
-When asked to plug the phone, press Home+On/Off+Back (and keep them pressed) and then plug the phone on usb.
-Release Home+On/Off and only keep the "back" button pressed.
If you followed the sequence properly, you will see the green led on and flashing process will start. If not, try it again.
Remember, it is all about the sequence of press/release the buttons.
Regards, D_d
DaRk_dOg said:
Hello Divr,
You cannot pull off the battery on X10 mini.
In order to restore a bricked mini:
-Launch SEUS (NOT Pc Companion)
-When asked to plug the phone, press Home+On/Off+Back (and keep them pressed) and then plug the phone on usb.
-Release Home+On/Off and only keep the "back" button pressed.
If you followed the sequence properly, you will see the green led on and flashing process will start. If not, try it again.
Remember, it is all about the sequence of press/release the buttons.
Regards, D_d
Click to expand...
Click to collapse
PC Companion also can detect the phone, I have tried it
theandroidlover said:
Hi, I have install mini CM and my phone is blocked on the boot logo cyanogenmod
Help me please !!!
Click to expand...
Click to collapse
If you wanna turn Off your phone....to get out from Boot-Loop...then i got an hardware Trick to Switch Off......just tell me if you need or not(After this you can never Brick your phone)
twins.7 said:
PC Companion also can detect the phone, I have tried it
Click to expand...
Click to collapse
Hello twins.7,
Pc Companion is more vulnerable in errors, whereas SEUS is more successful in restoring and flashing our phones. I had many failures, restoring a phone with PcCompanion and not a single one with SEUS. It's reported by others too.
Regards, D_d
DaRk_dOg said:
Hello Divr,
You cannot pull off the battery on X10 mini.
In order to restore a bricked mini:
-Launch SEUS (NOT Pc Companion)
-When asked to plug the phone, press Home+On/Off+Back (and keep them pressed) and then plug the phone on usb.
-Release Home+On/Off and only keep the "back" button pressed.
If you followed the sequence properly, you will see the green led on and flashing process will start. If not, try it again.
Remember, it is all about the sequence of press/release the buttons.
Regards, D_d
Click to expand...
Click to collapse
What if the battery is empty?
Dissasemble your phone.
You must disconnect the mini's batt before put the phone in flash mode.
Remove the plastic cap (the small one) cover of the battery plug. With a plastic object unplug the battery and plug it again.
Then start SEUS and try again.
cluster2a said:
What if the battery is empty?
Click to expand...
Click to collapse
Hello cluster2a.
Plug it on the AC Charger (NOT the usb) and leave it there for a couple of hours. You should then, have sufficient power to flash it.
Never let your phone, totally drain its battery.
Regards, D_d
DaRk_dOg said:
Hello Divr,
You cannot pull off the battery on X10 mini.
In order to restore a bricked mini:
-Launch SEUS (NOT Pc Companion)
-When asked to plug the phone, press Home+On/Off+Back (and keep them pressed) and then plug the phone on usb.
-Release Home+On/Off and only keep the "back" button pressed.
If you followed the sequence properly, you will see the green led on and flashing process will start. If not, try it again.
Remember, it is all about the sequence of press/release the buttons.
Regards, D_d
Click to expand...
Click to collapse
i also tried this. pressing home/button/back the light blink red. plug in release home/power light turn green. still show...no software for phone / latest software, no repair option.
i also tried pc comp., run it without plug phone, then got repair option and then plug phone. after checking still ...no software for phone / latest software....
DaRk_dOg said:
Hello Divr,
You cannot pull off the battery on X10 mini.
In order to restore a bricked mini:
-Launch SEUS (NOT Pc Companion)
-When asked to plug the phone, press Home+On/Off+Back (and keep them pressed) and then plug the phone on usb.
-Release Home+On/Off and only keep the "back" button pressed.
If you followed the sequence properly, you will see the green led on and flashing process will start. If not, try it again.
Remember, it is all about the sequence of press/release the buttons.
Regards, D_d
Click to expand...
Click to collapse
this is the only method that worked on my bricked x10 mini.. many big thanks
you're a star, that worked perfectly (i also uninstalled pc companion, which seemed to interfere)
javierarenas said:
You must disconnect the mini's batt before put the phone in flash mode.
Remove the plastic cap (the small one) cover of the battery plug. With a plastic object unplug the battery and plug it again.
Then start SEUS and try again.
Click to expand...
Click to collapse
more details please
where is this plastic cap exactly
please
You can also search the web for Omnius Server, and flash your phone again. I had my U20i bricked. SEUS only said that I had latest software and didn't let me flash it. I had to pay I think 16 euros to re-flash it with Omnius server, but it really worked. There's also in the forum a flash tool, and links to several files, but I don't know how to do it...
DaRk_dOg said:
Hello Divr,
You cannot pull off the battery on X10 mini.
In order to restore a bricked mini:
-Launch SEUS (NOT Pc Companion)
-When asked to plug the phone, press Home+On/Off+Back (and keep them pressed) and then plug the phone on usb.
-Release Home+On/Off and only keep the "back" button pressed.
If you followed the sequence properly, you will see the green led on and flashing process will start. If not, try it again.
Remember, it is all about the sequence of press/release the buttons.
Regards, D_d
Click to expand...
Click to collapse
I try thank youuuu
thanks dood, worked like charm!
DaRk_dOg said:
Hello Divr,
You cannot pull off the battery on X10 mini.
In order to restore a bricked mini:
-Launch SEUS (NOT Pc Companion)
-When asked to plug the phone, press Home+On/Off+Back (and keep them pressed) and then plug the phone on usb.
-Release Home+On/Off and only keep the "back" button pressed.
If you followed the sequence properly, you will see the green led on and flashing process will start. If not, try it again.
Remember, it is all about the sequence of press/release the buttons.
Regards, D_d
Click to expand...
Click to collapse
will it work for hard bricked device
DaRk_dOg said:
Hello Divr,
You cannot pull off the battery on X10 mini.
In order to restore a bricked mini:
-Launch SEUS (NOT Pc Companion)
-When asked to plug the phone, press Home+On/Off+Back (and keep them pressed) and then plug the phone on usb.
-Release Home+On/Off and only keep the "back" button pressed.
If you followed the sequence properly, you will see the green led on and flashing process will start. If not, try it again.
Remember, it is all about the sequence of press/release the buttons.
Regards, D_d
Click to expand...
Click to collapse
Hi D_d
I have bricked my phone by flashing the relock.ftf file..now it does not responds to flashtool. Will your above instruction work in my case.
Regards,
Related
Hello everyone, i'm sorry for my bad English, I accidentally moved the "app" folder from the system to the sd card using root explorer, and I have lost almost all applications (market, root explorer, astro, ecc...), then I try to resolve this problem doing a hard reset , but now the phone goes on and after about 1 minutes goes off again again and again, and I can not stop it. also does not connect to pc .. anyone knows a way to fix it? I think I'll take it in assistance, the phone is still under warranty but it was rooted
Thank you guys
maicolboss said:
Hello everyone, i'm sorry for my bad English, I accidentally moved the "app" folder from the system to the sd card using root explorer, and I have lost almost all applications (market, root explorer, astro, ecc...), then I try to resolve this problem doing a hard reset , but now the phone goes on and after about 1 minutes goes off again again and again, and I can not stop it. also does not connect to pc .. anyone knows a way to fix it? I think I'll take it in assistance, the phone is still under warranty but it was rooted
Thank you guys
Click to expand...
Click to collapse
flash using binarys guide or repair from seus
Unfortunately i can't connect my phone in flash mode...
maicolboss said:
Unfortunately i can't connect my phone in flash mode...
Click to expand...
Click to collapse
they should stick this solution lol
to connect the phone use this:
put the seus ready to repair
connect the cable to phone and pc
press both midle and right button at the same time and press the power button
when phone goes down keep pressing only the right button
reconpt said:
they should stick this solution lol
to connect the phone use this:
put the seus ready to repair
connect the cable to phone and pc
press both midle and right button at the same time and press the power button
when phone goes down keep pressing only the right button
Click to expand...
Click to collapse
You're a genius!!!!.... I thought my phone was dead.... but now is resurrected ... thank you so much!!
reconpt said:
they should stick this solution lol
to connect the phone use this:
put the seus ready to repair
connect the cable to phone and pc
press both midle and right button at the same time and press the power button
when phone goes down keep pressing only the right button
Click to expand...
Click to collapse
Dude, you're a machine - my phone wouldn't power off so i was waiting for it to run flat lol... your post helped a ****load to get my phone repaired.
Thanks!
reconpt said:
they should stick this solution lol
to connect the phone use this:
put the seus ready to repair
connect the cable to phone and pc
press both midle and right button at the same time and press the power button
when phone goes down keep pressing only the right button
Click to expand...
Click to collapse
had the same issue of not being able to connect my phone to pc to repair with seus. thanks loads the "press both midle and right button at the same time and press the power button" trick!!!
I tried your solution but seus just tell me my mini it's up-to-date and there's no more the button for installing anyway android.
The phone just reboots over and over
I seem to have a slightly different problem. I tried the process and right after it said that the phone is connected, the green light on the phone goes out and it looses connection to the phone and prompts me to reconnect. My phone is stuck on the sony ericsson logo, will not shut off and will not boot, can not be detected by the computer. I think I have little more than a very expensive hockey puck.
reconpt said:
they should stick this solution lol
to connect the phone use this:
put the seus ready to repair
connect the cable to phone and pc
press both midle and right button at the same time and press the power button
when phone goes down keep pressing only the right button
Click to expand...
Click to collapse
THANKYOU THANKYOU THANKYOU THANKYOU THANKYOU
Could never live without my phone, thankyou your the best
lije87 said:
I tried your solution but seus just tell me my mini it's up-to-date and there's no more the button for installing anyway android.
The phone just reboots over and over
Click to expand...
Click to collapse
try this mate
http://forum.xda-developers.com/archive/index.php/t-981935.html
I have the same problem SEUS says my phone is "up-to-date" what can we do?
Hey yhis helped me too thanks !
something similiar too...
Hi,
Here is my problem.
I have Xperia x10 mini/ yesterday , but mistake, I installed the firmware of the X10 mini PRO !!!
Now, once I understood the mistake, I want to flash with x10 mini firmware.
In order to flash I need to have FLASHTOOLS and need to press the BACK button - the problem is that since the phone is using now the wrong firmware, the BACK button (needed for the flushing ) doesn’t do anything and thus, I cannot install the correct firmware. I tried pushing all other buttons without any luck.
Any idea how I can overcome this problem ? I can’t use my phone now.
ramimos said:
Hi,
Here is my problem.
I have Xperia x10 mini/ yesterday , but mistake, I installed the firmware of the X10 mini PRO !!!
Now, once I understood the mistake, I want to flash with x10 mini firmware.
In order to flash I need to have FLASHTOOLS and need to press the BACK button - the problem is that since the phone is using now the wrong firmware, the BACK button (needed for the flushing ) doesn’t do anything and thus, I cannot install the correct firmware. I tried pushing all other buttons without any luck.
Any idea how I can overcome this problem ? I can’t use my phone now.
Click to expand...
Click to collapse
The flashmode is initialized before any firmware is loaded, so that isn't your problem
It should always work when your phone is turned off, you press the back-button and attach it to your usb-cable, it should enter flashmode.
If you can't turn it off, connect your phone to your pc, press home and power together till the screen goes black, and then press the back-button.
Well,
I managed to turn the phone off ( using the home+power button), then release the two of them, pressing the BACK button and connecting the USB cable .
nothing hapenns till i release the BACK button and then the phone starts to load with the previous problem.
before installing the the wrong firmware, using the BACK button was OK.
any idea?
update
I managed to hold together the HOME+BACK button and then pushed the POWER button and flashed the E10i 2.1.1 A.0.6 firmware!!!!
while doing it, i noticed for a meesage that the phone is not rooted.
upon finishing the flashing, the phone doesnt boot up, i managed to see the green light and thats all.
i also downloaded the S1 tool in order to root the phone but it says that it can not detect the phone....
what should i do now?
---------- Post added at 01:11 PM ---------- Previous post was at 12:15 PM ----------
update #2
phone doesnt boot up.
when i connect the flashtool i get the message "Device connected in flash mode".
how to continue from that point ?
Hi all. I have multiple problems in my x10i.it has 2.1 It was rooted and worked fine..few days ago I tried to wipe the phone and did the master reset via xrecovery ..after the restart it just hanged at the boot logo and xrecovery is not working from then....I wanted to update with SEUS via USB... but the phone is not connecting as well...What should I do? PLZ HELP ME GUYZ........
Hi,
Seus doesn't recognize your x10 even if you hold back button while plugging usb (flash mode) ?
This week my x10 2.1 crashed (I suppose it was because of rooting with superoneclick without rebooting immediatly), and wasn't recognized by windows. It was in a loop turnig on/off and only putting off battery could turn it off really. Big Problem.
The only solution I found : putting off battery, pluggin usb cable, holding back button and putting on battery. Back button still hold (like flash mode) until seus recognize x10. Then it runs alone and install rom (after I rooted with flashtools and launched jit optimisation, witch increase truely x10 performances!).
Probably seus not recognize your phone because you have a rooted and custom firmware in your x10 and xrecovery is not working because you did a reset and then you delete some files from your phone, you can reinstall it with the x10flashtool or to make a complete restore firmware whit the same x10flashtool
If SEUS/PCC doesn`t recognize your phone, remove them from PC and reinstall them.
You have an USB driver problem
ohm74 said:
Hi,
Seus doesn't recognize your x10 even if you hold back button while plugging usb (flash mode) ?
This week my x10 2.1 crashed (I suppose it was because of rooting with superoneclick without rebooting immediatly), and wasn't recognized by windows. It was in a loop turnig on/off and only putting off battery could turn it off really. Big Problem.
The only solution I found : putting off battery, pluggin usb cable, holding back button and putting on battery. Back button still hold (like flash mode) until seus recognize x10. Then it runs alone and install rom (after I rooted with flashtools and launched jit optimisation, witch increase truely x10 performances!).
Click to expand...
Click to collapse
nope, phone is not connecting in flash mood..i pulled of the battery and did as u said,,nothings working ......
Take the phone with the warranty for repairing.
mistake_man said:
Probably seus not recognize your phone because you have a rooted and custom firmware in your x10 and xrecovery is not working because you did a reset and then you delete some files from your phone, you can reinstall it with the x10flashtool or to make a complete restore firmware whit the same x10flashtool
Click to expand...
Click to collapse
one more thing....i checked the device manager se drivers r working f9.....when i connect phone via usb cable the green light automatically turns on....even b4 i press back key
iMatth3w said:
Take the phone with the warranty for repairing.
Click to expand...
Click to collapse
I bought it from ebay ...no warrenty... think thats stupid :/
rumanbsl said:
nope, phone is not connecting in flash mood..i pulled of the battery and did as u said,,nothings working ......
Click to expand...
Click to collapse
Did you wait for at least 30 seconds before putting battery inside phone (to make sure clearing all memories? And sure you hold back button before, during and after?
Otherwise, what does happen if you press and hold volume button before turning on the phone (and keep volume button hold)?
rumanbsl said:
one more thing....i checked the device manager se drivers r working f9.....when i connect phone via usb cable the green light automatically turns on....even b4 i press back key
Click to expand...
Click to collapse
Well your usb is definitly working then as its glowin green?..
Are you sure you are doing it all right? It happened the same to me, and it ended I was pressing the wrong buttom (I knew which one was the correct one, but was blind cause I was scared that Ive broke it totally), a day later I noticed it and I was able to flash my phone.
However, read a guide and follow it step by step, reinstall everything and start from beginning maybe?
Or use the repair function with PC Companion
Hi! I had the same problem!
1. Search and download from this forum Flashtool 0.2.6
2. Install it.
3. Download from this forum one generic ROM (for exemple X10i_2.1.A.435_GLOBAL-GGL GENERIC 1232-9897 )
4. Put the file in directory Flashtool/firmware
5. Launch X10flashtool.exe
6. DO NOT PUT THE USB CABLE IN THE PHONE
7.From option "flash select the desired ROM
8. Wait the program to begin(a picture will appear)
9. Pressing the back button, insert the usb cable.
10. Wait the flashing to begin and release the back button.
Follow instructions and WAIT around 5 minutes until flashing will complete
11. Send me two words if it helps you! Success!
ohm74 said:
Did you wait for at least 30 seconds before putting battery inside phone (to make sure clearing all memories? And sure you hold back button before, during and after?
Otherwise, what does happen if you press and hold volume button before turning on the phone (and keep volume button hold)?
Click to expand...
Click to collapse
I've did everything as u told.....no luck ! guess its the time to go to repair center...btw a guy from help center told me about software tampered,,!!out of luck
if your x10i brick (SE Logo) and can't reboot can't access xrec and can't access flash mode (for flash generic rom)
i have a solution..
1. connect the phone to PC (USB)
2. open superOneClick v1.55 and click shell root icon
3. open FlashTool 0.2.9.1 and click Ask Root Perms
4. click menu advanced --> clean --> clear cache
5. click xrecovery icon
6. click menu advanced --> Xrecovery--> Reboot into Recovery
7. look you phone.. bingo.. u can access Xrecovery and then just install u favorit custom rom n reboot..
8. now u phone normaly n u can access flash mode to flash generic rom..
and.. sory my english is bad hehe...
jakadewantara said:
if your x10i brick (SE Logo) and can't reboot can't access xrec and can't access flash mode (for flash generic rom)
i have a solution..
1. connect the phone to PC (USB)
2. open superOneClick v1.55 and click shell root icon
3. open FlashTool 0.2.9.1 and click Ask Root Perms
4. click menu advanced --> clean --> clear cache
5. click xrecovery icon
6. click menu advanced --> Xrecovery--> Reboot into Recovery
7. look you phone.. bingo.. u can access Xrecovery and then just install u favorit custom rom n reboot..
8. now u phone normaly n u can access flash mode to flash generic rom..
and.. sory my english is bad hehe...
Click to expand...
Click to collapse
sorry i`m spanish and my english is very bad.
My problem: my x10 cant acces flash mode because pc dont detect the phone. Dont charge, etc... the brick block charge dock, mini usb...any solution please.
try thread from DoomLORD : [DEV][How-To] Get Back to Stock Even With Broken / Damaged USB Port in http://forum.xda-developers.com/showthread.php?t=1054818
tarzerixx said:
sorry i`m spanish and my english is very bad.
My problem: my x10 cant acces flash mode because pc dont detect the phone. Dont charge, etc... the brick block charge dock, mini usb...any solution please.
Click to expand...
Click to collapse
Likely the USB port is dead and you have to send it in for repair.
I used flashtool 3.0, pretended I was gonna flash 2.1 onto it and wella it worked. Your idea fixed my phone Dude. Thanks for the help.
pccobra said:
I used flashtool 3.0, pretended I was gonna flash 2.1 onto it and wella it worked. Your idea fixed my phone Dude. Thanks for the help.
Click to expand...
Click to collapse
Please mention the steps, or link, when i press on shell root(in superone click) it keeps on waiting for device. (flashtool never enables ask for root).
NOTE: It happened when I was trying update my ROM Wolfbreak , I did factory rest and all other resets available on xRec . (xcluding sd card format) then i thought i should try reboot before installing new ROM. but it stucks on SE logo screen. please give me some thoughts to make it in working mode again
Thanks
RedAxe said:
Please mention the steps, or link, when i press on shell root(in superone click) it keeps on waiting for device. (flashtool never enables ask for root).
NOTE: It happened when I was trying update my ROM Wolfbreak , I did factory rest and all other resets available on xRec . (xcluding sd card format) then i thought i should try reboot before installing new ROM. but it stucks on SE logo screen. please give me some thoughts to make it in working mode again
Thanks
Click to expand...
Click to collapse
Hapenned the same to me...
I try to follow the steps, but i can't pass step 4 (it's unavaiable the "clean cache" bottom...)
Please help...
Restore original firmware with SEUS
RedAxe said:
...then i thought i should try reboot before installing new ROM. but it stucks on SE logo screen...
Click to expand...
Click to collapse
My X10 mini was a brick (or I thought it was) because it was behaving like you described: the phone was stuck on the SE logo and it wasn't entering Flash Mode although I pressed the back key when the Sony Ericsson white letters were displayed.
Here is my solution
Open SEUS and select your phone. Click Next.
SEUS will wait for the device.
Connect your bricked phone via the USB cable.
Then you must access Flash Mode, at all costs.
SEUS, PC Companion and FlashTool can detect this phone only in Flash Mode.
Note: If your phone is resetting correctly (pressing and holding Power+Center) and the phone is being detected as an unmounted removable drive on the computer as mine did, it should be able to enter Flash Mode, no matter it has been already stuck for ages on the first screen with the white letters. My phone had enough battery charge to go through the whole process.
To enter Flash Mode with the Xperia X10 Mini I had to:
1. Perform a hard reset of the phone (Press and hold Power+Center)
2. As soon as the phone vibrates, release both keys. Phone will restart.
3. The white Sony Ericsson logo will be displayed.
4. Press and hold Power+Center and immediatly the Back key (the three keys at the same time)
5. Keep the keys pressed until the LED turns green.
After doing the correct sequence and entering Flash Mode, the LED turns green and the screen turns completely black. SEUS detected my phone at this point, downloaded the original firmware and installed it automatically.
do u have trick for my problem here forum.xda-developers.com/showthread.php?t=1388476
my x10 just vibrate once and stack on blank screen.
Sent from my X10i using Tapatalk
When I use SEUS It keep saying "You have the newest software available"
I tried the hard reset and all. The phone now just won't start at all
Hi,
i got the same problem what you describe ive stuck at the SE logo and cant get into recovery and i cant use flashtool. i tried to do what you say in the first post, but when i press the shell root button, it says "wait for device" then its not responding, and i cant moce on to the next step... what should i do now?
Ketoth said:
My X10 mini was a brick (or I thought it was) because it was behaving like you described: the phone was stuck on the SE logo and it wasn't entering Flash Mode although I pressed the back key when the Sony Ericsson white letters were displayed.
Here is my solution
Open SEUS and select your phone. Click Next.
SEUS will wait for the device.
Connect your bricked phone via the USB cable.
Then you must access Flash Mode, at all costs.
SEUS, PC Companion and FlashTool can detect this phone only in Flash Mode.
Note: If your phone is resetting correctly (pressing and holding Power+Center) and the phone is being detected as an unmounted removable drive on the computer as mine did, it should be able to enter Flash Mode, no matter it has been already stuck for ages on the first screen with the white letters. My phone had enough battery charge to go through the whole process.
To enter Flash Mode with the Xperia X10 Mini I had to:
1. Perform a hard reset of the phone (Press and hold Power+Center)
2. As soon as the phone vibrates, release both keys. Phone will restart.
3. The white Sony Ericsson logo will be displayed.
4. Press and hold Power+Center and immediatly the Back key (the three keys at the same time)
5. Keep the keys pressed until the LED turns green.
After doing the correct sequence and entering Flash Mode, the LED turns green and the screen turns completely black. SEUS detected my phone at this point, downloaded the original firmware and installed it automatically.
Click to expand...
Click to collapse
u totally saved me =D
X10 mini revived!
Hi,
The procedure described above works fine until you've the phone recognized by the computer.
Here's how It has finally been recognized:
1) Completely switch off the phone (Do not leave it with SE logo).
-You can do the either by removing the battery connector (be cautious) under a rubber on the left(not above) of the camera lens.
-OR when the USB is plugged in,
(1.1) press center + back + power button until power off,
(1.2) then release center and power button AND KEEP back button down(about 2-5 seconds) until green led lights on. remark:LED will stay green until you unplug USB or phone switches on.
(1.3) Unplug USB.
Your phone should be OFF now. SE logo doesn't appear anymore (Wait 30s to be sure)
2) Unplug the USB cable from computer and plug it in another USB port of the PC.
3) At this time, if you plug USB on your X10 mini, it should be recognized as a SEMC device (It has worked for me).
-Success? Go step 4
-Failure, retry (from step 2 should be enough) with another USB port. If you've tryied all ports already, I've no idea.
4) If step 3 is successful, unplug USB.
5) Start SEUS (update service program from SE), choose you phone, follow the instructions on screen. Remark: Even if it says that you've got the last version, there is an "Install" button available on the bottom right corner. Click it!
Hope it'll help.
deBelch.
PS: Many thanks the whole forum for the help provided.
hello guys..my se xperia x10 mini pro stuck on the SE logo..and i tried to press power+ home button but it din't change anything.It also give 0.3sec led green flash while pressing the power and the menu button.can anyone plz help me with this..???
cruzstar said:
hello guys..my se xperia x10 mini pro stuck on the SE logo..and i tried to press power+ home button but it din't change anything.It also give 0.3sec led green flash while pressing the power and the menu button.can anyone plz help me with this..???
Click to expand...
Click to collapse
Update phone using SEUS....
Just google SUES
Definitely it will work....
Sent from my X10i using xda premium
yea i have use the SEUS..by pressing the back button..but it dont work..plz help me
Dear sir i already done that procedures but no use in seus shown u already updater software. plz help me
Cannot unbrick xperia mini E10i
Ketoth said:
My X10 mini was a brick (or I thought it was) because it was behaving like you described: the phone was stuck on the SE logo and it wasn't entering Flash Mode although I pressed the back key when the Sony Ericsson white letters were displayed.
Here is my solution
Open SEUS and select your phone. Click Next.
SEUS will wait for the device.
Connect your bricked phone via the USB cable.
Then you must access Flash Mode, at all costs.
SEUS, PC Companion and FlashTool can detect this phone only in Flash Mode.
Note: If your phone is resetting correctly (pressing and holding Power+Center) and the phone is being detected as an unmounted removable drive on the computer as mine did, it should be able to enter Flash Mode, no matter it has been already stuck for ages on the first screen with the white letters. My phone had enough battery charge to go through the whole process.
To enter Flash Mode with the Xperia X10 Mini I had to:
1. Perform a hard reset of the phone (Press and hold Power+Center)
2. As soon as the phone vibrates, release both keys. Phone will restart.
3. The white Sony Ericsson logo will be displayed.
4. Press and hold Power+Center and immediatly the Back key (the three keys at the same time)
5. Keep the keys pressed until the LED turns green.
After doing the correct sequence and entering Flash Mode, the LED turns green and the screen turns completely black. SEUS detected my phone at this point, downloaded the original firmware and installed it automatically.
Click to expand...
Click to collapse
Hello Guys,
I need your urgent help.
I cannot restore phone with SEUS or Companion. It says I already have the soft.
Getting fatal errors in Flashtool, I am stuck with SE logo and bootloader relocked.
I have the stock kernel but CM7 ROM.
Do you have any other ideas?
Tanks a lot!
deBelch said:
Hi,
The procedure described above works fine until you've the phone recognized by the computer.
Here's how It has finally been recognized:
1) Completely switch off the phone (Do not leave it with SE logo).
-You can do the either by removing the battery connector (be cautious) under a rubber on the left(not above) of the camera lens.
-OR when the USB is plugged in,
(1.1) press center + back + power button until power off,
(1.2) then release center and power button AND KEEP back button down(about 2-5 seconds) until green led lights on. remark:LED will stay green until you unplug USB or phone switches on.
(1.3) Unplug USB.
Your phone should be OFF now. SE logo doesn't appear anymore (Wait 30s to be sure)
2) Unplug the USB cable from computer and plug it in another USB port of the PC.
3) At this time, if you plug USB on your X10 mini, it should be recognized as a SEMC device (It has worked for me).
-Success? Go step 4
-Failure, retry (from step 2 should be enough) with another USB port. If you've tryied all ports already, I've no idea.
4) If step 3 is successful, unplug USB.
5) Start SEUS (update service program from SE), choose you phone, follow the instructions on screen. Remark: Even if it says that you've got the last version, there is an "Install" button available on the bottom right corner. Click it!
Hope it'll help.
deBelch.
PS: Many thanks the whole forum for the help provided.
Click to expand...
Click to collapse
nope...didnt work...there is NO Install beneath...wonder why? is it i am using the latest SEUS?
greetings. please i followed your steps to unbricked my device but my x10 cant boot into flash-mode. whenever i try to connect it via flash-tool. the green light comes on but in some few seconds it boot automatically. and when i try to flash anything it boot automatically. please help me
---------- Post added at 12:21 AM ---------- Previous post was at 12:16 AM ----------
greetings. please i followed your steps to unbricked my device but my x10 cant boot into flash-mode. whenever i try to connect it via flash-tool. the green light comes on but in some few minutes it boot automatically. and when i try to flash anything it boot automatically. please help me
Hi,
I would like to ask you for advice before throwing my X10 mini away and buying something else.
I have had MiniCM7 installed for a very long time (more than a year), and upgraded to all versions without any problem. Today I installed MiniCM9 3.0.2, but I decided to reinstall MiniCM7 because of some problems detected with this version, so I went to SEUS, downgraded to 2.1.1.A.0.6, installed BusyBox, xMiniRecovery, root and flashed MiniCM7 2.2.0 and gapps. I have done it quite a lot of times before.
But, when I tried to reboot onto MiniCM7 2.2.0, my phone was stuck onto Sony Ericsson logo. Here's what I did:
1) Ok, Home+Power and reenter into recovery by pressing back key. No, no luck, it doesn't enter into any recovery.
2) B plan, I'll go to SEUS again. Home+Power, connect USB and keep back key pressed. Nothing, SEUS doesn't recognize anything, but Companion does activate a little popup on my Windows, as if it detects my phone plugged into my computer. No red, yellow, or green lights in the phone.
3) C plan. Flash kernel directly. I downloaded kernel from http://forum.xda-developers.com/showthread.php?p=17674938#post17674938 and used FlashTool. But, again, when I press Home+Power, connect the USB cable and press back key, it doesn't recognize anything, FlashTool is waiting for me to connect something. Antivirus is disabled.
If I keep back key pressed, no SE logo appears; black screen. If I release back key for a little while, SE logo appears and it gets stuck.
Both if I connect it to the computer or to the power socket, no green/yellow/red led appears.
Does anybody have any idea? Everything (cable and phone) were working wonderfully before flashing 2.1.1.A.0.6 for the last time.
Kind regards,
Jordi
Ok,before u try this u should know it will delete everything of phone memory:apps,contacts,etc.
And it removes root and recovery and phone will be like the day u bought it except that bootloader is not touched if unlocked stays unlocked
TRY AT UR OWN RISK
Steps:
1-download sony erricsson pc companion
2-click support zone and choose software update
3-before clicking continue click on repair phone
4-wait till loads and choose phone type
5-concentrate on this one cuz it has 2 methods
5a:if ur phone doesent restart automaticlly just plug usb in computer first then with phone powered off hold the back button and connect the usb cable only let hold when it says u can
5b:if ur phone DOES restart automaticlly remove battery till u reach this step and put back cover bedside till ur done with this method what were gonna do is when we reach this step we quickly plug battery and before it restarts just hold back and insert usb cable.
6-wait to install
7-congratulations unbricking
8-(optional):click the thanks button :xD
Sent from my U20i using XDA
Hi,
Thank you very much for your quick answer. I had never realized the procedure shown in steps 2-4.
But Companion refuses to install it! "It's impossible to install or setup update components of phone sotfware" grrrrrrrrrrrrr Tomorrow I'll try to get another computer and follow your procedure.
Thank you very much
Always happy to help as ive been in such issues alot
Sent from my U20i using XDA
You say you have an X10 Mini, and not an X1O Mini-Pro.
The X10 Mini requires you to run the nAa-kernel in order to run the latest verstion of MiniCM7.
You say you downgraded back to stock firmware and installed MiniCM7 again, did you forget about the kernel?
SmG67 said:
You say you have an X10 Mini, and not an X1O Mini-Pro.
The X10 Mini requires you to run the nAa-kernel in order to run the latest verstion of MiniCM7.
You say you downgraded back to stock firmware and installed MiniCM7 again, did you forget about the kernel?
Click to expand...
Click to collapse
Aaaaaaaaaaaaaaaaarghhhhhh you are right!!!!!!! I have installed kernels and versions a lot of times on my device, and I was so confident of myself that this time I didn't realize I was missing one of the most important steps!!!!!!!!!!!!!!! So stupid of me.......!!!!!!!
I've tried PC Companion as suggested before, but no way: it doesn't detect the "flash mode" at boot time. I keep pressing Back key and I only get a black screen; when I release Back key, SE logo appears and gets stuck forever. It doesn't matter if I try SEUS, PCCompanion or FlashTool, it's always the same. I can't shut it down, just restart over and over again via Home+Power.
Does anybody know what can I do?
Kind regards,
Jordi
jordisegurapla said:
Aaaaaaaaaaaaaaaaarghhhhhh you are right!!!!!!! I have installed kernels and versions a lot of times on my device, and I was so confident of myself that this time I didn't realize I was missing one of the most important steps!!!!!!!!!!!!!!! So stupid of me.......!!!!!!!
I've tried PC Companion as suggested before, but no way: it doesn't detect the "flash mode" at boot time. I keep pressing Back key and I only get a black screen; when I release Back key, SE logo appears and gets stuck forever. It doesn't matter if I try SEUS, PCCompanion or FlashTool, it's always the same. I can't shut it down, just restart over and over again via Home+Power.
Does anybody know what can I do?
Kind regards,
Jordi
Click to expand...
Click to collapse
Only thing i can think off is to press home-power-back at the same time and release home and power when the screen goes black, all this with the phone connected to the pc via usb, but i'm not sure if that will work.
SmG67 said:
Only thing i can think off is to press home-power-back at the same time and release home and power when the screen goes black, all this with the phone connected to the pc via usb, but i'm not sure if that will work.
Click to expand...
Click to collapse
I've tried that already, doesn't work...
Looks bad, huh???
SmG67 said:
Only thing i can think off is to press home-power-back at the same time and release home and power when the screen goes black, all this with the phone connected to the pc via usb, but i'm not sure if that will work.
Click to expand...
Click to collapse
I do not know what did I do, but by trying for the 1000th time to do the Home+Power+Back key combination with USB connected and keeping Back key pressed, and pressing and releasing it madly afterwards, while FlashTool was waiting for me to flash MiniCM7, FlashTool has reacted!!!!!! It allowed me to install MiniCM7 again!!!
What happened? I do not know, perhaps I pressed Back key just the microsecond that the hardware needed it.
Thank you very much!!!!
hahaha, cool And here i was thinking you were trying to flash the kernel, lol
But good luck
SmG67 said:
hahaha, cool And here i was thinking you were trying to flash the kernel, lol
But good luck
Click to expand...
Click to collapse
Ok, you are right again; FlashTool allowed me to install the kernel ;-) and then, everything else.
Thank you very much, really!!!
Hello comrades,
I have xperia x10 mini pro. I rooted phone with Flashtool and installed CWM. I tried to boot it in flash mode (turned off phone, back button held and plugged in USB into the phone), but what I get is that my phone turned on always, like that I pressed Power button.
Earlier I couldn't boot it into the flash mode and I got that I charging battery, but after I installed CWM, phone always turns on.
Due to, I can't re-flash it because it always turns on. I tried with flashtool, PC companion, SEUS but all software need that I turn off phone and then hold back button and plug in usb and what I get is turned on phone. Please help me how to fix this problem.
I would like to re-flash it to stock 2.1.1.A.0.6 (2.1-update1).
Phone turns on even if I just plug in usb to phone (one end is in the PC and when I plug in other end into the phone, phone turns on). What is wrong guys?
bokivaol said:
Phone turns on even if I just plug in usb to phone (one end is in the PC and when I plug in other end into the phone, phone turns on). What is wrong guys?
Click to expand...
Click to collapse
Happened to me b4 if u want to repair with pc comp just remove the battery till u reach connection step then quickly connect battery and cable (nvm the cover) and hold back button when connecting if u do fast enough will work
sent from my u20i xperia x10 mini pro running mini cm9 3.0.2 on nAa ics 3
THX nAa. VERY MUCH!!!
Leave your phone plugged in and press POWER-HOME and BACK all together, as soon as the screen turns completelly black (backlight off too) releast POWER and HOME, and leave the back-button pressed, that will probably work too.
LukBoy99 said:
if u want to repair with pc comp just remove the battery till u reach connection step then quickly connect battery and cable (nvm the cover) and hold back button when connecting if u do fast enough will work
Click to expand...
Click to collapse
Can you explain me a little more detailed, i didn't get you very well. I am noob
How do you mean until I reach connection step, where should I reach connection step?
You take out the battery, then you go into PC Companion and follow the steps to repair your phone, until it asks to connect your phone in flash-mode.
Then do as he said (put the battery in etc.)
SmG67 said:
You take out the battery, then you go into PC Companion and follow the steps to repair your phone, until it asks to connect your phone in flash-mode.
Then do as he said (put the battery in etc.)
Click to expand...
Click to collapse
It doesn't work.
I tried and POWER-BACK-HOME buttons while the phone is plugged in (turned off and turned on), same sh..t. Phone starts like that I powered it on
stitypta had
What do you think, what will happened if I wipe it using CWM? Can I brick it on that way?
If you mean formatting your phone, so you don't have a system on there anymore... that probably will give you a brick. Flashmode is a hardware feature, implemented to install firmware and enable reparations to your phone's software.
Deleting everything you can will not magically solve your problem, as far as i know.
It might help if you get mad at the phone and abuse the back-button by repeatedly pressing it when connecting the phone.
SmG67 said:
If you mean formatting your phone, so you don't have a system on there anymore... that probably will give you a brick. Flashmode is a hardware feature, implemented to install firmware and enable reparations to your phone's software.
Deleting everything you can will not magically solve your problem, as far as i know.
It might help if you get mad at the phone and abuse the back-button by repeatedly pressing it when connecting the phone.
Click to expand...
Click to collapse
Does this mean that I have hardware problem. Phone works without any problem.
Somehow it doesn't detect you pressing the back-button, maybe there is some dust or dirt inbetween the contacts or something, since you flashed sucessfully before i don't think it's a serious hardware-problem.
SmG67 said:
Somehow it doesn't detect you pressing the back-button, maybe there is some dust or dirt inbetween the contacts or something, since you flashed sucessfully before i don't think it's a serious hardware-problem.
Click to expand...
Click to collapse
I didn't flashed it before, I couldn't do that. I couldn't unlock bootloader, because I couldn't boot it in flash mode (phone just show that battery charging), after installing CWM now phone even don't show that battery is charging (it turns on when I plug in USB in the phone without holding any button). This is nightmare!
You are still on the original firmware then?
I mean, your phone still works?
SmG67 said:
You are still on the original firmware then?
I mean, your phone still works?
Click to expand...
Click to collapse
Yes, I am on original firmware and phone still works, but I have problem to boot it in flash mode. When I plug in USB cable in the phone it turns on, like that I pressed POWER button. I don't press any button, but when I plug in usb cable 10-20 seconds and phone is on.
Yes, because your phone detects the usb-cable getting plugged in, even when it's off, it thinks you want to charge it, so (normally) it loads the kernel in order to start the charging-process, that is normal behaviour. I have been on a kernel that didn't support that feature, and it booted into the full rom before it started charging.
In short: the usb-port also functions as a power-button, sort off
Does the back-button work normally when you're on the firmware? (Like, open the app-drawer, pressing back-button should close it?)
SmG67 said:
Does the back-button work normally when you're on the firmware? (Like, open the app-drawer, pressing back-button should close it?)
Click to expand...
Click to collapse
Yes, the back button works perfect, closing apps (not close apps, but back to the phones "desktop"), back to previous pages in browser...
I am concerned because, before I installed CWM , when it was OFF and plugged in on USB, phone just showed black screen and when I clicked on some button I could see that battery is charging, that was all. Now, when I plug in USB it turns on like I pressed POWER button.
And off course never booted in flash mode because it turns on
SmG67 said:
Does the back-button work normally when you're on the firmware? (Like, open the app-drawer, pressing back-button should close it?)
Click to expand...
Click to collapse
What is app-drawer, I don't know what is that.
oh, that's the bit where you find all your installed apps, the grid you see when you press on the little triangle on the bottom of your desktop, or swipe up on the desktop.
I honestly don't know why your phone won't go into flash-mode though. Maybe try to take out your battery for about 10 minutes so your phone gets rid of all charge and static, and then try again.
SmG67 said:
I honestly don't know why your phone won't go into flash-mode though. Maybe try to take out your battery for about 10 minutes so your phone gets rid of all charge and static, and then try again.
Click to expand...
Click to collapse
I solved problem about POWER-ing on when I plug in USB. I installed new ROM "MiniCM7Pro_V21_Paul_XXX" via CWM because I didn't need to boot it in flash mode and now when I plug in USB I got that it charging battery and orange led diode.
But I can't boot it in flash mode even with new ROM, all the time orange led diode when I hold back button and plug in USB. I wiped out all date except something about "battery" from Advanced CWM options.
bokivaol said:
Hello comrades,
I have xperia x10 mini pro. I rooted phone with Flashtool and installed CWM. I tried to boot it in flash mode (turned off phone, back button held and plugged in USB into the phone), but what I get is that my phone turned on always, like that I pressed Power button.
Earlier I couldn't boot it into the flash mode and I got that I charging battery, but after I installed CWM, phone always turns on.
Due to, I can't re-flash it because it always turns on. I tried with flashtool, PC companion, SEUS but all software need that I turn off phone and then hold back button and plug in usb and what I get is turned on phone. Please help me how to fix this problem.
I would like to re-flash it to stock 2.1.1.A.0.6 (2.1-update1).
Click to expand...
Click to collapse
i dont have time to read if this was resolved but you need to leave your phone of for about 2 min the little bugger holds a charge for quit a bit you got one of the newer ones like mine i got this info from sony website at least 30sec power off before attempting to do the above steps also i do know how to get the phone out of this refer to the this thread http://forum.xda-developers.com/showthread.php?t=1635286&page=2 i only know this cause iam you !! lol as soon as i find a stock rom boom i am
http://minus.com/lbg0XZRW728Kwu ling for stock rom bro
follow step for step with the referance link above to reflash stock rom thanks that dude that told me
and it works cause i rebricked it lol i reflashed the same rom that did this to my phone and so far all above steps in referance link seem to be working"
http://forum.xda-developers.com/showthread.php?t=1636504 follow to the t you hav i.c.s 4.0 i guess works like a charm ! between both guides 25 min !!! yesterday i put 7hrs !! enjoy bro and thank thank the guys that root me they are the true credit iam just passing the info on too you that i got from both guides. look at my post and you will see i had this problem follow these steps and you will be fine remeber firs boot is the longest
best thing that ever happened to me was i bricked my my xperia mini pro u20 haha got ics out it lol