[Q] Phone not detected in Odin - Fascinate Q&A, Help & Troubleshooting

I have CWM 3.0.8, and want to get back to the red recovery, so that I can flash a new rom on my fascinate. The problem is, that I can not for the life of me get my phone to show up on Odin. I have tried on two different computers. I have used Odin on both computers for this phone, so the drivers are all installed. Any ideas? The rom I have now is a force close nightmare. I would like to get back to something that is stable.
Thanks for any help,
Brad

bradbradbrad said:
I have CWM 3.0.8, and want to get back to the red recovery, so that I can flash a new rom on my fascinate. The problem is, that I can not for the life of me get my phone to show up on Odin. I have tried on two different computers. I have used Odin on both computers for this phone, so the drivers are all installed. Any ideas? The rom I have now is a force close nightmare. I would like to get back to something that is stable.
Thanks for any help,
Brad
Click to expand...
Click to collapse
Follow this guide.
http://forum.xda-developers.com/showthread.php?t=1001064
Sent from my SCH-I500 using XDA Premium App

Ive used odin before, I just cant get the fascinate to be detected by the computer. It wont even mount the sd card via the usb cable to transfer files. I got the phone in download mode, connected to the computer through the usb cable, but can not get the yellow "added" dialog in odin so that I can flash the .tar file...
Thanks for the help so far,
Brad

Maybe a stupid question but do you have Odin open before you plug the phone in.
Sent from my SCH-I500 using XDA Premium App

You can also try to reinstall drivers or even odin check to see that you have odin 3 1.3 and maybe reinstall odin it can be found here in one of the forums.

I have tried it both ways, going into download mode, then opening odin, and first opening odin, then going into download mode.
Now, I have another problem. I was able to do a data wipe, which stopped the force close loop. I was then able to get my phone workable at least. Then, while resetting everything, I dropped it on my coffee table and the touch screen will not respond. The phone's soft keys work fine and i can turn it on, but have to do a battery pull to turn it off. I have tried turning off/rebooting, and again doing a data wipe. I don't know what else to do other than take it in, but I don't think that is possible since it is rooted

Related

Phone stuck on Phone-!-Computer screen.

So, I just got my phone back from Samsung for this issue. Start my newly returned phone up, it's running 2.2. I turn it off, hold volume buttons and plug in my USB cable - I get download mode instantly. I start up Odin 1.7, select the files and click start.
Nothing happens. Hangs up SetupConnection. I unplug the battery, then the USB cable, plug everything back in and I'm back at square one with this ****ing screen.
Last time I tried every single ****ing button combination posted on this website. I know my phone isn't hardware locked because I've never had a problem getting in to Download Mode before. Hell, I'd never had a problem with Odin not working properly before. What the hell is wrong? I have all the proper drivers installed. Why is this happening?
Now, Odin still sees my phone when I plug it in. If I click Start, sometimes it hangs on SetupConnection, sometimes it hangs on Initialization. I've read that you should still be able to flash while on this screen? Is this true? Either way, I think I'm ****ed again. Any help?
Also, I've read that maybe a jig will help get me in to download mode? Where can I buy a jig from?
you can go to stock jfd from that screen, it acts like download mode.
Once on jfd, download mode will work fine.
try the files in my going back to stock... also make sure to remove any other usb components (they can cause odin to hang).
I love you.
Something must be wrong with the files on my desktop, or perhaps the other USB cable I'm using is ****ed.
This is a bit embarrassing. For some reason I can't get root. I can get in to recovery and select reinstall packages, but every time it boots right back in to the OS. Any hints? Never had this issue before.
EDIT: So it looks like I have Superuser installed but since I can't get into Clockwork I can't flash any roms. What's going on? I can't find any other links where people couldn't get in to Clockwork.
EDIT2: Well, I installed ROM Manager and used it to "flash" CWM. Reinstall Packages worked this time it seems. Weird. Anyway, thanks for the help!
Cool, glad you were able to get it all sorted.

[Q] Galaxy I9100 bricked - Request help

Hi Everyone,
Need help with my I9100 which doesn't boot. I got this phone yesterday and was using it fine. Today i installed Kies and it prompted to upgrade firmware. I researched and found that it had improvements in battery life and decided to go for it. It downloaded the firmware and everything went fine until it prompted saying firmware upgrade failed and asked me to do firmware emergency recovery.
I googled to see more info regarding this error and couldnt get much information. Decided to go ahead with recovery as instructed. Again i got error " Firmware emergency recovery stopped due to GT-I9199 error". If the problem persistes please contact samsung service center.
Please suggest if this is recoverable error and any links to proceed and have a working phone.
Currently when i power on, i get a logo of phone connected to PC with yellow bang in middle. Any pointers much appreciated....
Thanks.
Don't worry, I think you can fix this yourself using ODIN. I mean, flash a custom rom through Download mode. (Turn the phone off, hold Volume Down + Home + Power for 4 seconds)
In this mode you can flash any kind of rom without doing your phone any harm. Just go to the Rom Development forum and choose your rom. I suggest Lightning Rom, because it uses ODIN, and has a very well-explained tutorial.
You can also flash a stock rom, you can get it from the Stock Rom thread, and flash that through ODIN.
Or get it fixed by Samsung and wait two weeks. (where they use exactly the same program, ODIN, to reflash the stock rom)
Look here
And here
And finally here
If all that doesn't work, take it back to samsung.
Also, KIES is a PoS, use Odin in future
Yep, KIES may look all official and reliable, but it actually seems to brick some SGS2's.
Thanks for the info's. Will try them and update soon.
No luck. I tried multiple times to update ROM using ODIN in download mode. Everytime it says NAND write operation failed and comes out. I am searching to see if any other option left before i take it back to samsung
Don't forget to try it with a different computer. Sometimes it's not the phone, it's the PC or the USB port.
Also, you can try flashing with Heimdall instead of Odin.
First of all;
Yellow triangle means you are running custom kernel/rom.
Press home+volume down and then power, to get into download mode , on your phone. If that works, take battery out, to stop it.
Go to:
Samfirmware.com
Download firmware from there. It is a rar file, I think. Open rar file to see what is in. 5 files? The biggest file has all of the other files in it.
Install via Odin. Select pda in Odin and select the biggest file from the rar.
Put your phone into download mode, connect usb and run Odin.
Adrian.
SGS2 I9100
Lite'nin rom 3.2
Make sure that all kies processes are closed or odin will fail.
Sent from my GT-I9100 using XDA Premium App
Keis? Hmm.
Adrian.
SGS2 I9100
Lite'nin rom 3.2
it gets worse...
my brother let the battery fall out of his S 2 while flashing with odin, now it wont power on in any mode, the PC wont recognise it at all, when i plug in the charger the phone gets hot, but does nothing.... whats the recovery method? or is it dead well and truly...
mightygoose said:
my brother let the battery fall out of his S 2 while flashing with odin, now it wont power on in any mode, the PC wont recognise it at all, when i plug in the charger the phone gets hot, but does nothing.... whats the recovery method? or is it dead well and truly...
Click to expand...
Click to collapse
You can buy a usb jig, specially designed to put you phone into download mode. Search for it on ebay. Take the battery out, plug in usb jig, replace battery and it should boot into download mode. If it does not, then the phone is dead.
Sent from my GT-I9100 using xda premium

[Q] Stuck in Bootloop, no recovery, odin wont recognize phone

I was running AOKP 38 when the battery died. The phone got stuck in bootloop and when i tried restoring from cwm I lost the ability to boot into ANY RECOVERY!!!
When i try odin, it wont recognize the phone and both my pc's give me the message that the usb device isnt working.
Please helppppppp
Sounds like you don't have the right USB drivers installed on your computers.
Sent from my SCH-I500 using Tapatalk
i've already unistalled and reinstalled the samsung drivers. when i plug the phone into pc, i get the windows error message that the usb device is malfunctioning and windows has stopped it.
You are in download mode, right? It's just that it's better to rule these things out and you didn't specifically say that it was.
I cant even 3 finger into recovery!!! The phone just continuously runs the samsung screen.
Remove the battery, then hold volume down and plug in the USB cable. Do you see a yellow triangle?
yes, the yellow triangle comes on
Let me explain a little further. Ive been running AOKP 38 and on thursday I let my battery fully die. The phone never came on again. I have done a nandroid backup and everything is also backed up in Titanium. The phone will not boot into recovery nor will phone boot at all. ODIN wont pick up my phone and I've bought a new Samsung chord and reinstalled the Samsung drivers. Still nada.
Try a different USB port. Also, give Heimdall Suite a try.
ok so i went out and scored a sweet fassy. Brought it home, hooked up to pc and it picks up!!!!! Go figure. Im sooooo lost
Shelby is probably right. You need to install the Google USB driver from SDK Manager.
Sent from my SCH-I500 using xda premium
mikey71 said:
ok so i went out and scored a sweet fassy. Brought it home, hooked up to pc and it picks up!!!!! Go figure. Im sooooo lost
Click to expand...
Click to collapse
My laptop totally recognizes my sister's stock fascinate, but stopped recognizing my fascinate after a similar low battery / bootloop situation.
I had much success using a totally different computer to flash with odin or heimdall. I had to try 3 diff pcs until i hit paydirt.
To this day, the two laptops I used all the time for my fascinate no longer recognize it, yet other pcs recognize & odin fine. Likely other programs interfering with USB. Either way, way easier to borrow someone's pc, than to try & troubleshoot what is up with the usb connection.
At least you can get into download mode. That's half the battle right there.
Try another pc or possibly heimdall & good luck
You are not alone, others have come back from this. http://forum.xda-developers.com/showthread.php?p=28326672
Sent from my SCH-I500 using xda premium

[Q] So what kind of brick do I have here?

I was in the process of flashing back to GB in ODIN when it froze on flashing the Modem. Now the phone does nothing. Black screen. Plug USB in and computer doesn't know its there, Download mode will not work, nothing works.
Will a usb jig get it back into download mode so I can try flashing again or is this thing straight gone?
Thanks.
Yes, a USB jig will work.
MultipleMonomials said:
Yes, a USB jig will work.
Click to expand...
Click to collapse
Well I built one and tried it... No go. Nothing happened. Blank screen.
BTW the battery was fully charged right before it bricked so I know the battery isnt dead.
Was the phone on when you plugged it in?
I fixed it. Had to do the Unbrickable Mod. Was a pain in the butt getting the contact pads jumped. Once I got it I was able to get into download mode with the supplied programs and flash back to stock.
Nicely done.
Well I jinxed myself. I went to flash a new ROM and now im stuck on the Samsung Logo. Using the previous method does no good. Just stuck on Sammy logo. I found a different Heimdall One-Click now but it fails to flash Modem and now it vibrates 3 times when the sammy logo is shown.. over and over... so its in a boot loop I take it? If I 3 finger it it shows the stock recovery but I am unable to move up or down in recovery. It just stays on the reboot device selection.. im able to select that with the menu softkey thats it. The vol up and down and power buttons do not respond in recover. Updating the Modem is what started this whole mess for me. When I originally was flashing this the other day ODIN froze on flashing Modem, that put me in a hard brick state requiring me to do the Unbrickable Mod. I got it out of that with ED05 Heimdall Once-Click but since then I have not been able to get it out of this soft brick. My galaxy just wont let me win. :-(
Have you tried using One-Click Resurrector?
MultipleMonomials said:
Have you tried using One-Click Resurrector?
Click to expand...
Click to collapse
Ya, thats how I get it into Download Mode... its the Only way I can get it into download mode actually.
Both Odin and Heimdall are having trouble flashing the phone in windows. Both recognize the phone and connect but will not flash anything. They just sit at uploading PIT/Setting Partitions.
The ED05 Heimdall One-Click in linux flashes the phone with success's accross the board but the phone just sits there on the samsung logo... no vibrating, no recovery, and unable to charge the battery. If I use the EH03 Heimdall One-Click in linux it will flash all the way til it gets to flashing Modem but then fails and the phone is stuck in bootloop on the samsung logo vibrating 3 times over and over. It can also get into the stock recovery but im unable to move up or down the menu. Volume buttons have no effect. The phone will now charge though. Full battery as of right now.
I tried using Odin and Heimdall on another windows computer and they will not move past setting Partitons/uploading PIT either. SO I know there isnt a conflict with my computer.
I would like to try a manual flash in Heimdall Front-End in linux but I have no clue how to install it in Linux. I hate that command line stuff. I guess I have to figure it out though if Im going to try it.
OK, success!
I am now back to stock. I was able to run Heimdall in linux and flash CWM recovery. I was able to get into the recovery and make selections in recovery with the volume buttons. I selected reboot in download. I went to Odin and tried flashing a stock EH03 rom and it worked.... I think the reason I couldnt do that before was because i was holding the power button down to keep it in download mode since that is what is required when in download mode via the unbrickable mod.
The windows based programs must not have liked me holding that power button. Weird. Anyways its working.. now on to getting this thing updated.
im having a similar issue, i can get into cwm, can use download, but when i try using Odin for the stock eh03 it instantly says all threads completed succeeded 0 failed 0. when i reboot in cwm it just takes me to samsung logo wont go any further
Try heimdall.
Ya Heimdall in linux will surely give you a win.

[Q] Stuck in ODIN mode and can't get out

Hello
My situation goes as follows: I'm on a Cyanogenmod 11 nightly, as I flash a new ROM from time to time. So I know how to get into recovery and that kind of things. I've installed TWRP recovery, instead of the CWM one. I'm on a mac by the way.
As I was a little bit fast, I accidentally rebooted into download mode instead of recovery. Now my phone remains that way, only without the info in the top left (normally it says ODIN Mode and four other lines of information).
I tried to get the battery out and to drain the battery, both gave the same result: it booted in "downloading... do not turn off target !!"
I tried ODIN, Kies, Heimdall and adb trough terminal, and even the CM installer; none of these things seemed to recognize my phone.
I've been googling for over two hours now and I'm getting desperate. Is my phone ready for the bricks? I can't go to a shop tomorrow as it is the national holiday in Belgium. So still 32 hours of trying ahead of me...
Any ideas? If you guys have any additional questions, please ask.
Thanks in advance
R.
erdeebee said:
Hello
My situation goes as follows: I'm on a Cyanogenmod 11 nightly, as I flash a new ROM from time to time. So I know how to get into recovery and that kind of things. I've installed TWRP recovery, instead of the CWM one. I'm on a mac by the way.
As I was a little bit fast, I accidentally rebooted into download mode instead of recovery. Now my phone remains that way, only without the info in the top left (normally it says ODIN Mode and four other lines of information).
I tried to get the battery out and to drain the battery, both gave the same result: it booted in "downloading... do not turn off target !!"
I tried ODIN, Kies, Heimdall and adb trough terminal, and even the CM installer; none of these things seemed to recognize my phone.
I've been googling for over two hours now and I'm getting desperate. Is my phone ready for the bricks? I can't go to a shop tomorrow as it is the national holiday in Belgium. So still 32 hours of trying ahead of me...
Any ideas? If you guys have any additional questions, please ask.
Thanks in advance
R.
Click to expand...
Click to collapse
Try removing the external memory card, if you have one.. and try the hard reset method.. sometimes it may work...search in forum for hard reset methods... or you can connect the phone and continue with odin again to see anything happens...:good:
cooljay5 said:
Try removing the external memory card, if you have one.. and try the hard reset method.. sometimes it may work...search in forum for hard reset methods... or you can connect the phone and continue with odin again to see anything happens...:good:
Click to expand...
Click to collapse
Removing simcard and external storage didn't work, as well as putting another card in my phone. I'll try the hard reset and come back to you.
Thanks!
cooljay5 said:
Try removing the external memory card, if you have one.. and try the hard reset method.. sometimes it may work...search in forum for hard reset methods... or you can connect the phone and continue with odin again to see anything happens...:good:
Click to expand...
Click to collapse
Odin does nothing, I tried Kies methode, but it stopped after the download.
erdeebee said:
Odin does nothing
Click to expand...
Click to collapse
Have you tried the hard rester method?
Whilst in download mode hold power button for about 1 minute until it vibrates? Maybe your buttons are stuck.
Sent from S3 Mini
Using XDA App
LiamAtkins90 said:
Have you tried the hard rester method?
Whilst in download mode hold power button for about 1 minute until it vibrates? Maybe your buttons are stuck.
Sent from S3 Mini
Using XDA App
Click to expand...
Click to collapse
Hard reset as in tried to flash trough Kies, I can't do anything else, right?
I tried the pwoer button, but it just loops in download mode, without the information on the top left.
I do get it into download mode WITH the information, but than Kies simply says there's no phone attached.
erdeebee said:
Hard reset as in tried to flash trough Kies, I can't do anything else, right?
Click to expand...
Click to collapse
Are you familiar with the PC flashing tool Odin? It's specifically for Samsung devices.
http://forum.xda-developers.com/gal...08-2013-odin-3-09-odin-1-85-versions-t2189539
Download and install Odin onto your PC it will flash a stock image onto your device (No root, Stock recovery)
http://www.sammobile.com
Head to Sammobile and download your ROM firmware specific to your device.
Run ODIN on your computer and connect your phone.
When it recognizes it, check "Auto Reboot" and "F.Reset Time".
Everything else should be left unchecked.
On your computer, unzip the ROM file you downloaded. It should give you something with the extension of
.tar.md5
Press "PDA" on ODIN and select this file.
Everything should be as shown here: http://gyazo.com/fea7a1c8b7a7b5bb287fb0a0c70056dc
Click Start and wait for it to do it's thing. It'll take quite a few minutes.
When it's finished, you're done.
If it hangs on boot ones it flashed, reboot to Stock Recovery and do a factory reset it should boot up fine now, (also 1st boot takes about 3 minutes.)
Let me know how it goes
EDIT: http://forum.xda-developers.com/galaxy-s3/help/guide-odin-flash-guide-t1671969
Stock Firmware is on this page
Sent from S3 Mini
Using XDA App
LiamAtkins90 said:
Are you familiar with the PC flashing tool Odin? It's specifically for Samsung devices.
http://forum.xda-developers.com/gal...08-2013-odin-3-09-odin-1-85-versions-t2189539
Download and install Odin onto your PC it will flash a stock image onto your device (No root, Stock recovery)
http://www.sammobile.com
Head to Sammobile and download your ROM firmware specific to your device.
Run ODIN on your computer and connect your phone.
When it recognizes it, check "Auto Reboot" and "F.Reset Time".
Everything else should be left unchecked.
On your computer, unzip the ROM file you downloaded. It should give you something with the extension of
.tar.md5
Press "PDA" on ODIN and select this file.
Everything should be as shown here: http://gyazo.com/fea7a1c8b7a7b5bb287fb0a0c70056dc
Click Start and wait for it to do it's thing. It'll take quite a few minutes.
When it's finished, you're done.
If it hangs on boot ones it flashed, reboot to Stock Recovery and do a factory reset it should boot up fine now, (also 1st boot takes about 3 minutes.)
Let me know how it goes
EDIT: http://forum.xda-developers.com/galaxy-s3/help/guide-odin-flash-guide-t1671969
Stock Firmware is on this page
Sent from S3 Mini
Using XDA App
Click to expand...
Click to collapse
As I'm on a mac, I tried jodin, but it doesn't seem to recognize my phone.
Sorry
Sent from S3 Mini
Using XDA App
So, my phone is bricked?
Last try: A windows computer and it worked. Don't know why it didn't work on my mac.
Awesome. I'm happy for you mate. Glad you got it fixed
Sent from S3 Mini
Using XDA App
No not at all.your phone not brickd.only one option is to flash your phone via odin on 4.3 available on sammobile.
Hot thanks?
Sent from my GT-I9300 using XDA Free mobile app

Categories

Resources