Related
I tried to downgrade to 1.6 and now my phone wont turn on.
It will vibrate and the led will flash green? once during this vibrate but nothing more...
I cant get the thing into boot mode
Any help?
Z3X said:
I tried to downgrade to 1.6 and now my phone wont turn on.
It will vibrate and the led will flash red once during this vibrate but nothing more...
I cant get the thing into boot mode
Any help?
Click to expand...
Click to collapse
Try repairing using PC companion.
Welcome to this side of flashing issue. I just recovered from it this morning after hours of search and flashing. Jerpelea said that Kernel has gotten mixed up and try to take the battery our for a while and then put it in and try to go to boot, Flash earlier 1.6 ROM I did the R16 and it worked, I had a hardtime flashing with R26.
Nimche said:
Welcome to this side of flashing issue. I just recovered from it this morning after hours of search and flashing. Jerpelea said that Kernel has gotten mixed up and try to take the battery our for a while and then put it in and try to go to boot, Flash earlier 1.6 ROM I did the R16 and it worked, I had a hardtime flashing with R26.
Click to expand...
Click to collapse
Could you get into flash mode? I currently can not... I am bricking myself at the thought of my phone being bricked!!
I had the same problem a while ago and the only thing that worked was a firmware uploaded by jerpelea. Have a look at what I posted here http://forum.xda-developers.com/showpost.php?p=9206194&postcount=11
I had about the same problem with my phone a while back, I could still get it into flash mode if I was quick though. If you can get it into flash mode try and follow this tutorial on Youtube, it's a working way for downgrading from 2.1 to 1.6
ht tp:// w w w. youtube .c o m/watch?annotation_id=annotation_468774&v=K9qB8z6EjtY&feature=iv
If it bricks it will prolly brick after a few seconds, just pull out the battery and try again getting it into Flash Mode. Good luck
As stated on one of your other threads, until you've repaired your usb port posts like this are pointless.
I can angle it to get a connection. That's why I am continuing with this thread
But thanks
tie your x10 to a brick and throw it at a SE service centre.
Waste of a brick.
Hi there.... a similar thing happened to me. I have a UK T-mobile X10 which I had upgraded to nordic 2.1 and needed to downgrade back to 1.6 because I was getting a warranty exchange the next day.
I used the CDA method to change my phone cda back to uk t-mobile and the damn thing wouldnt downgrade via seus. Then I tried flashing to R2BA26 which bricked my fone...green light would come on and the damn thng would just vibrate!!!
I then flashed it with 2.1 Global generic from jeprelea's thread and everything is ok now!
XperiaX10iUser said:
As stated on one of your other threads, until you've repaired your usb port posts like this are pointless.
Click to expand...
Click to collapse
@Z3X, you've started 3 threads on this same topic, here, here and here.
Not
Hey guys.. i have a big problem with my X10
I wanted to flash back to the newest generic 2.1 (I had the newest rooted 2.1) .. turns out it wasnt such a smooth ride..
I used the "X10 Flash Tool" and the newest generic 2.1 rom from this thread
Everything went fine, no error messages but now my X10 will not boot.
When I turn it on I feel the phone vibrate for a split second as usual and then the phone's backlight keeps turning on and off and nothing happens.
I tried reflashing it with SEUS; Also no error messages and the update completed but still the same.
Is my phone bricked or is it worse?
Thanks in advance for any help!
Try reflash with THIS
Thank you for the reply.
Unfortunately it didn't work.. Flashing completed without any errors again but still I have the same problem..
Any other suggestions?
TimMun said:
Thank you for the reply.
Unfortunately it didn't work.. Flashing completed without any errors again but still I have the same problem..
Any other suggestions?
Click to expand...
Click to collapse
Try the repair function in PC Companion
delbuenno said:
Try the repair function in PC Companion
Click to expand...
Click to collapse
I will try that, thank you.
But, isnt the repair function in PC Companion practically the the same as reflashing with SEUS?
Fixed it!
Before I started this topic I had searched the forum for my problem but did not find anything. Just a moment ago i ended up at a thread here at xda (via google) with someone who had the same problem (XperiaX10User, you tried to help him to) and "Vazelos" posted a reply with a link to the "ROOT_F3v3.rar" by jerpelea.
I only did step 1 and got it working again.
1.6
R1FA014
(1.6 feels smoother then 2.1 )
did you update it to 2.1 again or steel using 1.6?
you've could also use davincyteam website, there you can buy the original rom. it's cost me about 15 dollars to have the old useless android 1.6. this is when you are really desperate.... hope it helped. : )
He guys. I've been trying to sort my friends X10i that's stuck on the boot screen displaying either the Sony Ericsson logo or a camera icon with an arrow pointing down towards an image of the phone,
He told me he tried to update the phone with SEUS and it switched off half way though. Since then it just hangs at boot as described above.
I have tried using SEUS. The phone is recognized and the process goes all the way to 100% but when I try and reboot after completion it just hangs again. Interestingly every time I connect it to SEUS it tells me there is new software available.
I have also tried using FlashTool 0.9.8.0 and these ROMS:
Sony Ericsson X10i_2.1.A.435_GLOBAL-GGL GENERIC 1232-9897
X10i_3.0.1.G.0.75_GLOBAL-GGL_GENERIC_1232-9897
X10_1.0_SE_StockRom_MultiTouch
Like SEUS, FlashTool reports that ROM flashing was successful and ask me to reboot but the same thing happens. It hangs.
My friend bought the phone second hand and so has no idea if it was running a stock or custom ROM or had a locked or unlock bootloader.
I've searched high and low on the forums for an answer and can't find one.
Can anyone help?
try flashing the doom kernel from flashtool
Hey finalbillybong dont despair, all is not lost.....yet
First be sure the phone is fully charged - like overnight....
Try playing around with flashtool... its quite powerful... go to 'help/ check drivers' and see what happens.
Just be sure to flash the right kernel (its easier to .ftf files) for the right rom. Some work really well together and some are just o.k. If unsure search the forums - i know its painful but read all the noob stuff.
Here are some links - some are fairly old but the principle is the same - just search the forums for updated versions/software.
http://forum.xda-developers.com/showthread.php?t=928210
http://forum.xda-developers.com/showthread.php?t=1305945
http://forum.xda-developers.com/showthread.php?p=24711910#post24711910
http://forum.xda-developers.com/showthread.php?t=928343
If all this fails I have had some luck using wotansever...
http://www.wotanserver.com/en/account/login
You gotta register but its free and it saved me from a potential brick a while ago.
I hope this helps - happy unbricking, and enjoy the journey of XDA
I have been visiting this site ever since I first read about X10 & was fascinated by it (I have always loved SE phones). Anyway, I have since gotten an X10i (AT&T) & have de-branded it as well as unlocking & rooting it. Here goes:
I installed Champs' Rom (x10sV9-addon) but didn't want all the clutter he had pre-installed. To make a long story short, I went back to Wolf's ROM via Xrecovery but something went wrong. I can no longer boot into Xrecovery & after SonyEricsson logo, screen goes blank, not black/blue just blank. The other problem is, since I can't see the screen, I can't turn on the USB connection so my PC/Flashtool/SEUS can recognize my device so I can fix it. This happened while trying to re-install Wolf's ROM & installing the following zip files via Xrecovery: Bravia_Xloud engine, Xperia S Player, Champ + Bar, x10_gb_stock_wifi_modules. Then I rebooted & I get the blank screen. I know it is on because I can turn the volume all the way down to vibrate. The "home" button still lights up. PLEASE, I need someone's help with this one as I am no expert, just a moderate tinkerer. ANY help/incite would be appreciated. Sorry, I can't even give you any screenshots. Can anyone out there help me out? Thanx in advance.
daRican! said:
I have been visiting this site ever since I first read about X10 & was fascinated by it (I have always loved SE phones). Anyway, I have since gotten an X10i (AT&T) & have de-branded it as well as unlocking & rooting it. Here goes:
I installed Champs' Rom (x10sV9-addon) but didn't want all the clutter he had pre-installed. To make a long story short, I went back to Wolf's ROM via Xrecovery but something went wrong. I can no longer boot into Xrecovery & after SonyEricsson logo, screen goes blank, not black/blue just blank. The other problem is, since I can't see the screen, I can't turn on the USB connection so my PC/Flashtool/SEUS can recognize my device so I can fix it. This happened while trying to re-install Wolf's ROM & installing the following zip files via Xrecovery: Bravia_Xloud engine, Xperia S Player, Champ + Bar, x10_gb_stock_wifi_modules. Then I rebooted & I get the blank screen. I know it is on because I can turn the volume all the way down to vibrate. The "home" button still lights up. PLEASE, I need someone's help with this one as I am no expert, just a moderate tinkerer. ANY help/incite would be appreciated. Sorry, I can't even give you any screenshots. Can anyone out there help me out? Thanx in advance.
Click to expand...
Click to collapse
You said the button still lights up? can you get into recovery? if so just wipe system and install a rom! and try flashing a kernel with flashtool!!!!
RE: Blank Screen After Flashing Custom ROM
Thanx for getting back to me so fast. As I said, the screen is blank. That is, the backlit display works but I can see nothing else. The "Home" button lights up when i press it but the display does nothing. If/When I reboot to try to enter XRecovery, I see the SonyEricsson logo followed by the backlit screen & nothing else. The Volume up/down buttons work as I am able to silence the phone by turning volume all the way down to vibrate. Because I cannot see what's on the display, I cannot turn USB on/off to connect to PC to run SEUS/Flashtool, etc. I.E. I cannot fix the device. Usually I just boot into XRecovery to fix a problem like this but that doesn't work.
x10
hy, install sony update service and repair your phone, then install again custom rom, the indications how to repair your phone software is in the program.
Best regards
Does USB need to be On or Off on the device for Update Service to run?
daRican! said:
Does USB need to be On or Off on the device for Update Service to run?
Click to expand...
Click to collapse
Update says I already have the latest Update installed.
Flash 2.3 off line update
Sent from my Xperia X10 using xda premium
daRican! said:
I have been visiting this site ever since I first read about X10 & was fascinated by it (I have always loved SE phones). Anyway, I have since gotten an X10i (AT&T) & have de-branded it as well as unlocking & rooting it. Here goes:
I installed Champs' Rom (x10sV9-addon) but didn't want all the clutter he had pre-installed. To make a long story short, I went back to Wolf's ROM via Xrecovery but something went wrong. I can no longer boot into Xrecovery & after SonyEricsson logo, screen goes blank, not black/blue just blank. The other problem is, since I can't see the screen, I can't turn on the USB connection so my PC/Flashtool/SEUS can recognize my device so I can fix it. This happened while trying to re-install Wolf's ROM & installing the following zip files via Xrecovery: Bravia_Xloud engine, Xperia S Player, Champ + Bar, x10_gb_stock_wifi_modules. Then I rebooted & I get the blank screen. I know it is on because I can turn the volume all the way down to vibrate. The "home" button still lights up. PLEASE, I need someone's help with this one as I am no expert, just a moderate tinkerer. ANY help/incite would be appreciated. Sorry, I can't even give you any screenshots. Can anyone out there help me out? Thanx in advance.
Click to expand...
Click to collapse
seem like u dont have a launcher...install launcher throuh flashtool
lilinbakar said:
seem like u dont have a launcher...install launcher throuh flashtool
Click to expand...
Click to collapse
I wish I had gotten this solution sooner. Not sure if it would have mattered. When trying to use Flashtool I kept getting an error saying my phone was not in "flash mode".
I solved my problem by flashing using Omnius & flashing firmware 'X10i_generic_SE_24_MultiTouch.rar'. This got my phone back but it was only 2.1 so I used 'DooMLoRD_v4_ROOT-zergRush-busybox-su' to get me back to 2.3, but this is where I'm at. I had Wolf's firmware before but right now I have no xRecovery installed. I thought I had rooted my phone but xRecovery isn't installed nor is Busybox.. Any ideas? Thanx in advance...EVERYONE @ XDA-DEVELOPERS rox!
I haven't replied to this post because I'm at my wit's end. I still can't get XRecovery installed & I think I've tried all the methods out there. Maybe my problem is that I restored my phone using Omnius. Flashtool works OK but I can't do anything but Flash on it. My phone is a headache now. It freezes up, crashes & sometimes won't read the SD card. Please help...
Sent from My X10a using XDA Premium
daRican! said:
I haven't replied to this post because I'm at my wit's end. I still can't get XRecovery installed & I think I've tried all the methods out there. Maybe my problem is that I restored my phone using Omnius. Flashtool works OK but I can't do anything but Flash on it. My phone is a headache now. It freezes up, crashes & sometimes won't read the SD card. Please help...
Sent from My X10a using XDA Premium
Click to expand...
Click to collapse
C if u can repair phone using SEUS now. Open the software without connecting phone. N then go to the update part. It should give u a repair option. Then follow those steps. Or else just connect ur phone n then start software. When it tells u ur phone is up to date click on that n then click on "repair". Then use the latest flashtool to root. Recoveries come with kernels so just flash a custom kernel.
Sent from my Xperia X10 using xda app-developers app
Many Thanks, I was finally able to use SEUS; before I could not. I used Flashtool to upgrade/downgrade kernel. However, I still don't have XRecovery installed & I'm not sure how to do this. I can't install XRecovery using Flashtool. Any help would be greatly appreciated. I would really like to install a custom Rom again.
I don't think u need to upgrade or downgrade.. just look for a link to download xrecovery here and follow instructions
Sent from my Xperia X10 using xda app-developers app
I'm Back, Baby!
AdX9170 said:
I don't think u need to upgrade or downgrade.. just look for a link to download xrecovery here and follow instructions
Sent from my Xperia X10 using xda app-developers app
Click to expand...
Click to collapse
I'm not sure how it went down but prior to this, I was unable to use SEUS. No matter what I did, I couldn't repair it. However, since your post, I was able to use SEUS & Flashtool to get back to where I was before I screwed up my X10a. I'm currently running Wolf's Rom (many thanx!!!) & am very satisfied w/all your help homey! You da man!
I noticed you are running ICS on your X10i. Any help so that I may partake of that deliciousness?
daRican! said:
I'm not sure how it went down but prior to this, I was unable to use SEUS. No matter what I did, I couldn't repair it. However, since your post, I was able to use SEUS & Flashtool to get back to where I was before I screwed up my X10a. I'm currently running Wolf's Rom (many thanx!!!) & am very satisfied w/all your help homey! You da man!
I noticed you are running ICS on your X10i. Any help so that I may partake of that deliciousness?
Click to expand...
Click to collapse
Ur welcome i don't think u need help you just flashed a custom ROM.. the procedure for installing ICS is the same. Although it'd be better if you are on stock before installing it.. just look for an ICS ROM that u like (I'm using feralab n it works like a charm).
Get the kernel n ROM.. as usual, put the ROM zip on ur SD card, flash the kernel, install ROM from recovery
Although before installing:
1. In recovery go to mounts n storage
2. Format system data n cache
3. Mount system, data n cache (note that if the mounting is successful the options should change to unmount system, unmount data, unmount cache respectively)
4. Then install ROM
5. The installer is GUI based so it'll guide u really well through the installation
Sent from my Xperia X10 using xda app-developers app
daRican! said:
I have been visiting this site ever since I first read about X10 & was fascinated by it (I have always loved SE phones). Anyway, I have since gotten an X10i (AT&T) & have de-branded it as well as unlocking & rooting it. Here goes:
I installed Champs' Rom (x10sV9-addon) but didn't want all the clutter he had pre-installed. To make a long story short, I went back to Wolf's ROM via Xrecovery but something went wrong. I can no longer boot into Xrecovery & after SonyEricsson logo, screen goes blank, not black/blue just blank. The other problem is, since I can't see the screen, I can't turn on the USB connection so my PC/Flashtool/SEUS can recognize my device so I can fix it. This happened while trying to re-install Wolf's ROM & installing the following zip files via Xrecovery: Bravia_Xloud engine, Xperia S Player, Champ + Bar, x10_gb_stock_wifi_modules. Then I rebooted & I get the blank screen. I know it is on because I can turn the volume all the way down to vibrate. The "home" button still lights up. PLEASE, I need someone's help with this one as I am no expert, just a moderate tinkerer. ANY help/incite would be appreciated. Sorry, I can't even give you any screenshots. Can anyone out there help me out? Thanx in advance.
Click to expand...
Click to collapse
your LCD flexibel not improperly installed or detached, just open your x10 with screwdriver, and plug it in again your LCD flexible socket.
Iam sory if my english bad
Since I flashed my rom.My phone comes on but I can see anything, even when starting I can't see anything...
I really need help..
I will appreciate if you help me sort it out.
First of all, I wanted to say hello since this is my first post here :victory: and also please if I am posting wrong or if this question has been answered before forgive me, but I have already searched on google and on this forum and found no related posts Ok now about my problem:
I have a "Sony Ericsson Xperia X10mini Pro" with MiniCM10-4.1.0-20130416(mimmi) and 2.6.32.60-nAa-jb-05 kernel installed. Yesterday I decided to go back to U20_nAa-14_2.6.29.6-nAa-14 kernel and MiniCM7-2.2.1-mimmi-UNOFFICIAL because of wifi problems. I have done the flashing process with flashtool a lot of times in the past and I can't be wrong with it this time.
The problem started after flashing my kernel. Flashtool flashed the U20_nAa-14_2.6.29.6-nAa-14 kernel fine and phone was OK ready to reboot, so I unplugged the USB cable to start it on recovery so I could install Minicm from SD, but since I unplugged the cable the phone is DEAD! No led and no charging! :crying: When I try to reflash it, flashtool doesn't recognize it, I am pressing the back button and plugging it in but the phone is not recognized. It is not charging when I am plugging it on the charger and its not even trying to boot. I tried different cables, different battery (from a friend with the same phone) and nothing. Is there a way to force flash it back? Please any help will be appreciated since I have tried everything I know...
This has happend to other users too reasently.
I'm not sure if it only happens when going from JB to GB or it also happens when going from GB to JB.
We need to investigate why/how it happens and how to prevent it.
I always recomend to do a battery stat whipe just before a planed kernel-flash. I had simular problem once (no charge, no boot, no nothing) after a kernel-flash. I solved it by putting in a battery from another Mimmi (my wife has the same model). For some reason everything worked fine doing so. After battery stat whipe, the phone worked with my own battery again.
Best advise for others is for now: When you want to flash new kernel, first do a SEUS/PC Companion repair
This should be written into all install-instructions and mentioned again and again to avoid same problem for others.
I'm not sure how the other users solved this. Was it only by JTAG?
Thank you for your answer! :good:
First of all, there was no battery wipe option on this release of the kernel As I said before I have done it a couple of times in the past and every time with battery wipe, except this one and besides, I already tried your solution with my friends battery with no luck... So probably I am looking for another solution.
And one last thing about your post, what is "JTAG"?? I have seen it on other posts before but without explanation as to what it is, the only JTAG I know of is on the xbox360 And if its a possible solution how can I possibly do it? Is there a post with instructions?? (I will search on my own too now, but a recommended guide from someone who knows better is much appreciated!)
Emperor.dk said:
This has happend to other users too reasently.
I'm not sure if it only happens when going from JB to GB or it also happens when going from GB to JB.
We need to investigate why/how it happens and how to prevent it.
I always recomend to do a battery stat whipe just before a planed kernel-flash. I had simular problem once (no charge, no boot, no nothing) after a kernel-flash. I solved it by putting in a battery from another Mimmi (my wife has the same model). For some reason everything worked fine doing so. After battery stat whipe, the phone worked with my own battery again.
Best advise for others is for now: When you want to flash new kernel, first do a SEUS/PC Companion repair
This should be written into all install-instructions and mentioned again and again to avoid same problem for others.
I'm not sure how the other users solved this. Was it only by JTAG?
Click to expand...
Click to collapse
zero2048 said:
Thank you for your answer! :good:
First of all, there was no battery wipe option on this release of the kernel As I said before I have done it a couple of times in the past and every time with battery wipe, except this one and besides, I already tried your solution with my friends battery with no luck... So probably I am looking for another solution.
And one last thing about your post, what is "JTAG"?? I have seen it on other posts before but without explanation as to what it is, the only JTAG I know of is on the xbox360 And if its a possible solution how can I possibly do it? Is there a post with instructions?? (I will search on my own too now, but a recommended guide from someone who knows better is much appreciated!)
Click to expand...
Click to collapse
I'm pretty sure he flashed the x10blrelock.ftf instead of the u20 kernel and that is why his phone went dead.
A JTAG for our phone will do basically the same thing as a JTAG for the xbox, it restores original phone-state, but you need special equipment to do it, which is quite expensive. Most repair-shops will have one.
SmG67 said:
I'm pretty sure he flashed the x10blrelock.ftf instead of the u20 kernel and that is why his phone went dead.
A JTAG for our phone will do basically the same thing as a JTAG for the xbox, it restores original phone-state, but you need special equipment to do it, which is quite expensive. Most repair-shops will have one.
Click to expand...
Click to collapse
Thank you for the answer about jtag, I also checked for myself and found about the expensive equipment and propably its not the way for me
But about the kernel I am pretty sure it was the right file...
I know that a dead phone means bad kernel but its a process that I have done before a lot of times with success on mine and other phones My best guess is that something interrupted the process (bad usb cable?) or corrupted downloaded kernel file If that's the case is there an alternative solution? :crying:
zero2048 said:
Thank you for the answer about jtag, I also checked for myself and found about the expensive equipment and propably its not the way for me
But about the kernel I am pretty sure it was the right file...
I know that a dead phone means bad kernel but its a process that I have done before a lot of times with success on mine and other phones My best guess is that something interrupted the process (bad usb cable?) or corrupted downloaded kernel file If that's the case is there an alternative solution? :crying:
Click to expand...
Click to collapse
Usually, whatever you flash, even if it goes bad, flashmode is still available because that doesn't get tampered with, the only true hardbrick i've ever seen is when flashing that x10blrelock.ftf, which happens quite a lot lately.
Just for fun i even formatted my entire phone once, no kernel, no rom, completely empty, and flashmode was still there so it could be recovered.
I noticed that in some older versions of flashtool you sometimes had to click the kernel you wanted twice in order to get it to pick up the right one. Normally there's not much difference you can spot (most .ftf's just contain a loader and a kernel), but i had full SE firmware in .ftf format, which contained other sections too, and that's where i noticed it didn't always pick it up right at the first time of clicking.
SmG67 said:
Usually, whatever you flash, even if it goes bad, flashmode is still available because that doesn't get tampered with, the only true hardbrick i've ever seen is when flashing that x10blrelock.ftf, which happens quite a lot lately.
Just for fun i even formatted my entire phone once, no kernel, no rom, completely empty, and flashmode was still there so it could be recovered.
I noticed that in some older versions of flashtool you sometimes had to click the kernel you wanted twice in order to get it to pick up the right one. Normally there's not much difference you can spot (most .ftf's just contain a loader and a kernel), but i had full SE firmware in .ftf format, which contained other sections too, and that's where i noticed it didn't always pick it up right at the first time of clicking.
Click to expand...
Click to collapse
I understand what you mean and its really easy to make the mistake!! But well, still I don't think I made it but I guess there is nothing more to do anyway Thank you both for your help and I hope soon to return the favor on this forum :victory:
Can you tell me an average cost about the recovery process according to your experiance in your country?? Is is expensive in general?
zero2048 said:
I understand what you mean and its really easy to make the mistake!! But well, still I don't think I made it but I guess there is nothing more to do anyway Thank you both for your help and I hope soon to return the favor on this forum :victory:
Can you tell me an average cost about the recovery process according to your experiance in your country?? Is is expensive in general?
Click to expand...
Click to collapse
Someone in this forum had it done in Latvia for next to nothing.
In the USA it will cost you, your right arm.
zero2048 said:
I understand what you mean and its really easy to make the mistake!! But well, still I don't think I made it but I guess there is nothing more to do anyway Thank you both for your help and I hope soon to return the favor on this forum :victory:
Can you tell me an average cost about the recovery process according to your experiance in your country?? Is is expensive in general?
Click to expand...
Click to collapse
I just had a look online for prices in my country, it seems to be around €25.
SmG67 said:
I just had a look online for prices in my country, it seems to be around €25.
Click to expand...
Click to collapse
Emperor.dk said:
Someone in this forum had it done in Latvia for next to nothing.
In the USA it will cost you, your right arm.
Click to expand...
Click to collapse
Emperor.dk how old are you?
SmG67 thank you again and I will delete x10blrelock.ftf just in case....
hi guys, i have the same problem too, when my rom is minicm10 and my kernel is jb-naa-05, i want to go back to MiniCM7 because of green screen camera in MiniCM10 so i go back to MiniCM7, I flashed the right kernel e10-2.6.29.6-naa-14 for my x10 mini via flashtool and after i flash the kernel, my phone does not booting up(5 mins no booting up) so i decided to use seus but seus does not recognize my x10 mini, i try flashtool, but flashtool is not recognize my x10 mini so i tried to flash my created stock 2.1.ftf(thanks to leajian) and selected x10 mini from device selection(my x10 mini is not recognize in flashtool), then i wait until it finish, when i tried to open my phone, it boots up and show sony ericsson logo and it boots up(sucess!!!)...
sorry for my english...
so for all MiniCM10 Users, Dont try to go back to MiniCM7 If your Rom is MiniCM10 because it will cause your phone to not booting up like my problem.
Renz29 said:
hi guys, i have the same problem too, when my rom is minicm10 and my kernel is jb-naa-05, i want to go back to MiniCM7 because of green screen camera in MiniCM10 so i go back to MiniCM7, I flashed the right kernel e10-2.6.29.6-naa-14 for my x10 mini via flashtool and after i flash the kernel, my phone does not booting up(5 mins no booting up) so i decided to use seus but seus does not recognize my x10 mini, i try flashtool, but flashtool is not recognize my x10 mini so i tried to flash my created stock 2.1.ftf(thanks to leajian) and selected x10 mini from device selection(my x10 mini is not recognize in flashtool), then i wait until it finish, when i tried to open my phone, it boots up and show sony ericsson logo and it boots up(sucess!!!)...
sorry for my english...
so for all MiniCM10 Users, Dont try to go back to MiniCM7 If your Rom is MiniCM10 because it will cause your phone to not booting up like my problem.
Click to expand...
Click to collapse
If you follow nAa's instructions properly, there is no problem.
What you have to do:
Wipe data/factory reset in CWM on the JB-kernel
Flash the GB-kernel
Format /system, /data en /cache, so they get back to the original sizes
Flash the GB-ROM, or restore a previous GB-backup you may have had
No problems at all...
And your phone still had flashmode available, unlike the OP of this thread, so you don't have the 'same' problem
zero2048 said:
Emperor.dk how old are you?
Click to expand...
Click to collapse
Why?
If you are asking me on a date? LOL, the answer is no :laugh: