Hi All!
So, Im having problems starting my wifi
Device: x10a
Baseband: tried a bunch, 52, 54, 55, 58, all of them with different results.
Firmware: Wolfbreak CM 6.1.3, TripnMIUI 1.0.0, Official 2.1
Behavior:
Upon starting WiFi, I get a "Unable to start wi-fi" message.
Bluetooth works
Things I've tried:
Set wifi sleep policy to Never
Installed BladeWifiFix
Tried Static IP settings
Installed Wifi Manager app
Deleted /data/misc/wifi/wpa_supplicant.conf
Sometimes I can get wifi to enable, scan and associate, but the connection stalls after a while I am still connected but no traffic moves.
MAC Address always says "Unavailable"
Upon firing up logcat, here is what I see when I try to enable wifi:
Code:
D/dalvikvm( 1692): GC_EXTERNAL_ALLOC freed 1771 objects / 125904 bytes in 28ms
[B]I/WifiService( 1158): PLMN = 33403
I/WifiService( 1158): MCC = 334
I/WifiService( 1158): Number off channels stayed the same
D/SettingsWifiEnabler( 1284): Received wifi state changed from Unknown to Enabling[/B]
D/dalvikvm( 1158): GC_EXTERNAL_ALLOC freed 8310 objects / 451384 bytes in 120ms
I/WidgetPrefs( 1750): Loaded widget prefs for 11
I/ApStateWidget( 1750): updateAllWidgets, length = 0
D/dalvikvm( 1331): GC_EXPLICIT freed 1303 objects / 70256 bytes in 79ms
D/dalvikvm( 1368): GC_EXPLICIT freed 755 objects / 32480 bytes in 83ms
[B]E/wlan_tool( 3206): Fail to get OK status from AR6000[/B]
D/dalvikvm( 1549): GC_EXPLICIT freed 2389 objects / 110696 bytes in 110ms
[B]E/WifiService( 1158): Failed to load Wi-Fi driver.
D/SettingsWifiEnabler( 1284): Received wifi state changed from Enabling to Unkno
wn[/B]
I/WidgetPrefs( 1750): Loaded widget prefs for 11
I/ApStateWidget( 1750): updateAllWidgets, length = 0
D/dalvikvm( 1614): GC_EXPLICIT freed 581 objects / 36968 bytes in 81ms
I've searched like crazy for a solution, any tips are appreciated, please tell me how can I look at what is working when the wifi is ok, so I can try to work my way to have that config permanently.
Unfortunately, returning the phone is not a viable option
Update:
After leaving the phone charging overnight after flashing 2.1.A.0.435 via flashtool, wifi just works again, I had to reflash baseband 54 before flash tool could recognize my phone.
Phone Companion forced me to update and the repair option started working... only to say "there is no software available for your phone" after that, I couldnt get flashtool to flash firmware directly, I had to flash bb 54 package first, then firmware, not sure if this has something to do with the new "detection of rooted phones" changelog at EMMA.
Anyway, I'll track this issue and post here any info I found, in the meantime, im not that good of an android power user, where are the kernel modules located? Can I take a look at there and preserve that stuff before moving on to some custom rom, then plug them back in ala insmod (I have some linux background).
Does your phone work with other networks? Do other devices (not computers) work with your network? Wireless-N routers are known to have dodgy issues when shharing connection. Hav you tried resetting your password? Hav you checked ISP l's modem settings so that it allows devoces other than computers to access the network?
Good luck. I've been asking peeps with the same issues the same questions.
Sent from my X10i using XDA Premium App
Hi!
Yep, I've covered those basics, intentionally left them out.
I have a linksys AP 802.11G its as high as it goes, its hooked up to a cablemodem, sharing wifi with 3 laptops, 1 HTC Magic and 1 PSP, all the devices work perfectly. I just spent some time yesterday evening toying with settings (I have some Cisco training.... )
I have managed to get wifi working but its rather unstable, I get the "unable to start Wi-fi" randomly (works in the morning, broken on afternoon, no reboot!). I've settled on a slightly customized SEMC 2.1 firmware, Im waiting for devs to get a new wifi stack done to test drive it on my phone.
Seems like poking around on wifi sleep policy and manual IP configuration has something to do here, maybe wpa_supplicant is messing up something ?
It is odd as its the driver the one who crashes and burns badly
Thanks for the reply!
ztryfe said:
Hi!
Yep, I've covered those basics, intentionally left them out.
I have a linksys AP 802.11G its as high as it goes, its hooked up to a cablemodem, sharing wifi with 3 laptops, 1 HTC Magic and 1 PSP, all the devices work perfectly. I just spent some time yesterday evening toying with settings (I have some Cisco training.... )
I have managed to get wifi working but its rather unstable, I get the "unable to start Wi-fi" randomly (works in the morning, broken on afternoon, no reboot!). I've settled on a slightly customized SEMC 2.1 firmware, Im waiting for devs to get a new wifi stack done to test drive it on my phone.
Seems like poking around on wifi sleep policy and manual IP configuration has something to do here, maybe wpa_supplicant is messing up something ?
It is odd as its the driver the one who crashes and burns badly
Thanks for the reply!
Click to expand...
Click to collapse
Hmm, lots of people including myself have issues with the x10's connection.
My x10 disconnects when left idle. That was since the freex10 rom update...
Hopefully you can sort this out, or we'll all have to survive in the 2.3 gingerbread update.
I've found more info about the wifi interface, see the attached dmesg file, here are some interesting entries:
<4>[ 294.747420] Normal WIFI mode.
<4>[ 294.747566] ar6000_pwr_on --enter
<4>[ 294.747673] wow_irq 158, ret 0
<4>[ 294.749026] ar6000_readwrite_file: file /sys/devices/platform/msm_sdcc.2/detect_change filp_open error -2
<7>[ 295.942745] mmc1: queuing CIS tuple 0x01 length 3
<7>[ 295.961800] mmc1: queuing CIS tuple 0x1a length 5
<7>[ 295.970188] mmc1: queuing CIS tuple 0x1b length 8
<7>[ 295.972015] mmc1: queuing CIS tuple 0x14 length 0
<7>[ 295.975779] mmc1: queuing CIS tuple 0x80 length 1
<7>[ 295.976052] mmc1: queuing CIS tuple 0x81 length 1
<7>[ 295.976320] mmc1: queuing CIS tuple 0x82 length 1
<6>[ 295.976535] mmc1: new SDIO card at address 0001
<4>[ 295.986202] ar6000_available
<4>[ 295.986429] ar6000_readwrite_file: file /sys/devices/platform/msm_sdcc.2/detect_change filp_open error -2
<1>[ 295.988916] AR6000: Unsupported configuration opcode: 3
<4>[ 295.990304] Firmware mode set
<1>[ 295.990865] AR6000: Unsupported configuration opcode: 3
<1>[ 295.991055] AR6000: Unsupported configuration opcode: 5
<4>[ 295.991477] BMI enabled
<4>[ 295.995609] ar6000_avail: name=wlan0 hifdevice=0xc9db7000, dev=0xca744000 (0), ar=0xca744360
<4>[ 295.997440] old options [0] old sleep [13]
<4>[ 296.000062] Set hi_refclk_hz : Ref Clock=19200000
<4>[ 296.005482] ar6000_readwrite_file: file /data/misc/wifi/reg_code filp_open error -2
<4>[ 296.012448] get_reg_code_from_file: file read error, length=[0xfffffffe]
<4>[ 296.019008] AR6000: eeprom transfer by HOST
<4>[ 296.023159] eeprom_ar6000_transfer: Enter
<4>[ 296.026993] enable_SI
<4>[ 296.253144] read_mac_addr_from_file try to open file /data/misc/wifi/mac_address
<4>[ 296.253434] read_mac_addr_from_file file offset opsition: 0h
<4>[ 296.253637] read_mac_addr_from_file: length=17
<4>[ 296.254781] update_regCode : 0x60
<4>[ 296.254913] AR6K: Original Region Code= 0x4067
<4>[ 296.258566] disable_SI
<4>[ 296.259551] AR6000: BMISetAppStart
<4>[ 296.259850] AR6000: enable HI_OPTION_TIMER_WAR
<4>[ 296.260489] AR6000: firmware_transfer
<4>[ 296.260986] firmware_transfer: /system/lib/modules/athwlan.bin.z77 size 95352 bufsize 98304
<4>[ 296.282470] firmware_transfer: BMILZData: len=8192, remaining=90112
<4>[ 296.331338] firmware_transfer: BMILZData: len=8192, remaining=81920
<4>[ 296.376487] firmware_transfer: BMILZData: len=8192, remaining=73728
<4>[ 296.421931] firmware_transfer: BMILZData: len=8192, remaining=65536
<4>[ 296.466976] firmware_transfer: BMILZData: len=8192, remaining=57344
<4>[ 296.513780] firmware_transfer: BMILZData: len=8192, remaining=49152
<4>[ 296.558652] firmware_transfer: BMILZData: len=8192, remaining=40960
<4>[ 296.603967] firmware_transfer: BMILZData: len=8192, remaining=32768
<4>[ 296.649095] firmware_transfer: BMILZData: len=8192, remaining=24576
<4>[ 296.693829] firmware_transfer: BMILZData: len=8192, remaining=16384
<4>[ 296.736985] firmware_transfer: BMILZData: len=8192, remaining=8192
<4>[ 296.780152] firmware_transfer: BMILZData: len=8192, remaining=0
<4>[ 296.823353] firmware_transfer: /system/lib/modules/data.patch.hw2_0.bin size 1328 bufsize 4096
<4>[ 296.839499] ar6000_init() Got WMI @ 0xca95ba00.
<4>[ 297.047847] mac address = my:ma:ca:dd:re:ss
<4>[ 297.048192] ar6000_init() WMI is ready
<4>[ 297.048360] wmi_control_rx() : Unknown id 0x101e
<4>[ 297.048660] AR6000 Reg Code = 0x60
<4>[ 297.049142] AR6K: set txpwr : 14 successfully
<6>[ 297.220578] ADDRCONF(NETDEV_UP): wlan0: link is not ready
<4>[ 297.271533] AR6000 scan complete: 16
<4>[ 297.345889] AR6000 scan complete: 16
<4>[ 297.399869] AR6000: configure to the same channel number [0xb]
<4>[ 297.423791] AR6000: configure to the same channel number [0xb]
<4>[ 298.143360] select 1354 (tion.simpaytype), adj 15, size 4280, to kill
<4>[ 298.143504] select 1486 (lservicesetting), adj 15, size 4352, to kill
<4>[ 298.143643] select 3857 (man.WifiManager), adj 15, size 4542, to kill
<4>[ 298.143774] send sigkill to 3857 (man.WifiManager), adj 15, size 4542
<4>[ 298.574081] select 1354 (tion.simpaytype), adj 15, size 4229, to kill
<4>[ 298.574226] select 1486 (lservicesetting), adj 15, size 4301, to kill
<4>[ 298.574368] select 3932 (csson.idd.agent), adj 15, size 4324, to kill
<4>[ 298.574497] send sigkill to 3932 (csson.idd.agent), adj 15, size 4324
<4>[ 299.475873] AR6K: ar6000_cleanup_module ar6000_destroy [0]
<4>[ 299.475996] +ar6000_destroy
<4>[ 299.480605] debug_hdr_ptr: 0x5018f0
<4>[ 299.532510] select 1354 (tion.simpaytype), adj 15, size 4212, to kill
<4>[ 299.532654] select 1486 (lservicesetting), adj 15, size 4284, to kill
<4>[ 299.532794] send sigkill to 1486 (lservicesetting), adj 15, size 4284
<4>[ 299.597168] Length: 0 (Total size: 1500)
<4>[ 299.598258] ar6000_stop_endpoint -- enter
<4>[ 299.598353] ar6000_stop_endpoint(): WMI stopped
<4>[ 299.598444] Shuting down HTC ....
<4>[ 299.613138] Attempting to reset target on instance destroy....
<4>[ 299.767475] Reset target ret 0
<4>[ 300.021381] -ar6000_destroy
<4>[ 300.024235] Free irq 158
<4>[ 300.024311] ar6000_pwr_down --enter
<4>[ 300.029941] ar6000_readwrite_file: file /sys/devices/platform/msm_sdcc.2/detect_change filp_open error -2
<4>[ 300.030205] ar6000_cleanup: success
<6>[ 300.052561] mmc1: card 0001 removed
Related
Hi,
I have a HK version Streak 5, wanna to upgrade it to stock 360.
The upgrade process is successful, but the wifi shows "error" after boot.
Then I revert it to stock 318, the wifi works again.
Here is one part of the bootlog with 360
==from 360 bootlog==
<4>[ 196.603672] dhd_module_init: sdio_register_driver failed
<4>[ 198.190332] dhd_bus_start failed bus is not ready
I guess that is reason, but I don get how to overcome it.
Code:
<4>[ 193.240389] BootLog, +dhd_module_init
<4>[ 193.240407] HW rev:#22
<4>[ 193.395788] WLAN init: bt pulse start **************
<4>[ 193.507750] WLAN init: bt pulse done ***************
<4>[ 193.610019]
<4>[ 193.610026] Dongle Host Driver, version 4.217.63.0
<4>[ 193.610045]
<4>[ 193.610048] Dongle Host Driver, version 4.217.63.0
<4>[ 193.610061] BootLog, -dhd_module_init, ret=0
<7>[ 193.672594] mmc1: queuing CIS tuple 0x80 length 7
<7>[ 193.675755] mmc1: queuing CIS tuple 0x80 length 2
<7>[ 193.684456] mmc1: queuing CIS tuple 0x80 length 9
<7>[ 193.702528] mmc1: queuing CIS tuple 0x80 length 21
<6>[ 193.714406] mmc1: new SDIO card at address 0001
<4>[ 193.726534] DHD: dongle ram size is set to 393216(orig 393216)
<4>[ 196.603672] dhd_module_init: sdio_register_driver failed
<4>[ 196.603749] module dhd is loaded by WifiService(240)
<4>[ 198.190332] dhd_bus_start failed bus is not ready
<4>[ 198.196259] eth0: Broadcom Dongle Host Driver mac=00:00:00:00:00:00
<4>[ 198.451144] Binder Thread #(296) sends SIGKILL to id.partnersetup(594)
<4>[ 205.735104] oid.setupwizard(313) sends SIGKILL to oid.setupwizard(313)
<6>[ 205.743517] binder: 155:155 transaction failed 29189, size 52-0
<4>[ 206.909914] ActivityManager(171) sends SIGKILL to enetworksetting(575)
<4>[ 208.031582] Binder Thread #(296) sends SIGKILL to com.android.mms(536)
<4>[ 208.042856] Binder Thread #(297) sends SIGKILL to d.apps.uploader(617)
<4>[ 211.839349] Binder Thread #(159) sends SIGKILL to oid.voicedialer(588)
<4>[ 211.850506] Binder Thread #(297) sends SIGKILL to com.svox.pico(627)
<4>[ 216.520099] Binder Thread #(295) sends SIGKILL to .cooliris.media(608)
<4>[ 217.033596] Binder Thread #(295) sends SIGKILL to d.process.media(405)
<6>[ 219.436029] mmc1: card 0001 removed
<4>[ 219.440976] module dhd is unloaded by WifiService(240)
I have two question
1. Should I upgrade other mbns with stock 360 ?? (I already flash dps1 & amss)
2. How to disable the auto upgrade system check ?? (At least I don want the upgrade information if I need to use it with stock 318)
Please use the Q&A Forum for questions Thanks
Moving to Q&A
My aria Wifi stopped working with the original HTC rom,
not aware of having done anything to cause this.
Bluetooth and FM radio are still working so the BCM4329 chip is probably OK?
To get closer to the problem I
unlocked the bootloader: using HTC's unlock mechanism
rooted the device: using Unrevoked on Ubuntu
installed ClockworkMod
to backup the HTC rom
install cm-7.2.0-liberty.zip
Using Terminal Emulator or adb I see
netcfg => shows no eth0 nor wlan0
#> ./adb.sh
List of devices attached
HT0A1RJ01423 device
# service check wifi
Service wifi: found
# service check network_management
Service network_management: found
# svc wifi enable
gives the error "E/WifiService( 173): Failed to load Wi-Fi driver."
I also tried the app FXR Wi-Fi fix and rescue
which hangs "Connecting to supplicant
================================================================
D/FXR ( 603): [AsyncTask #1] WiFi returned to non enabled state, renabled=true
D/SettingsAppWidgetProvider( 335): Widget is from a previous version... Let's update
D/SettingsAppWidgetProvider( 335): No instances yet... Wait for at least one instance to exist before adding global settings
I/ActivityManager( 173): No longer want com.android.mms (pid 434): hidden #16
E/WifiService( 173): Failed to load Wi-Fi driver.
D/SettingsAppWidgetProvider( 335): Widget is from a previous version... Let's update
D/SettingsAppWidgetProvider( 335): No instances yet... Wait for at least one instance to exist before adding global settings
D/FXR ( 603): [main] onProgressUpdate Progress: Connecting to supplicant
D/SettingsAppWidgetProvider( 335): Widget is from a previous version... Let's update
D/SettingsAppWidgetProvider( 335): No instances yet... Wait for at least one instance to exist before adding global settings
================================================================
# cat /proc/kmsg
<6>[ 290.172882] [LS][CM3602] ALS value: 0x0, level: 1 #
<6>[ 292.078765] [LS][CM3602] ALS value: 0x3, level: 1 #
<4>[ 292.870056] wifi_set_power = 1
<6>[ 292.870269] liberty_wifi_power: 1
<6>[ 293.030029] [LS][CM3602] ALS value: 0x0, level: 1 #
<4>[ 293.156066] wifi_set_carddetect = 1
<6>[ 293.156280] liberty_wifi_set_carddetect: 1
<7>[ 293.156677] mmc0: card_present 1
<6>[ 293.156921] mmc0: Slot status change detected (0 -> 1)
<4>[ 293.160736]
<4>[ 293.160736] Dongle Host Driver, version 4.218.248.20
<3>[ 295.807342] mmc0: Command CRC error
<3>[ 295.808624] mmc0: Command CRC error
<3>[ 295.809875] mmc0: Command CRC error
<3>[ 295.812469] mmc0: Command CRC error
<3>[ 295.813690] mmc0: Command CRC error
<3>[ 295.814941] mmc0: Command CRC error
<3>[ 295.816558] mmc0: Command CRC error
<3>[ 295.817199] mmc0: error -84 whilst initialising SDIO card
<4>[ 305.155731] dhd_module_init: sdio_register_driver timeout
<4>[ 305.156921] wifi_set_power = 0
<6>[ 305.157409] liberty_wifi_power: 0
<4>[ 305.365081] wifi_set_carddetect = 0
<6>[ 305.365447] liberty_wifi_set_carddetect: 0
<7>[ 305.365783] mmc0: card_present 0
<6>[ 305.365997] mmc0: Slot status change detected (1 -> 0)
================================================================
What does the CRC error imply?
So I am looking for some advice on a way to prove whether the hardware is alive.
Is there a command like "lshw" that I could run to see the network device?
Thanks!
Hello
SKotreboval by som apoň originál firmware z vašich tabletov kto má tento. Na stránkach MyAudio
EN: I need original Firmware(ROM) from this tablet. On product website
Code:
ht tp:// slovensky. myaudioworld. com/mysupport/firmware/series-1016-dcc/
SK:som nasiel nejake "firmware" ktoré sú vo forme 5001.img a 5002.img avšak zverejnený oficiálny návod nefunguje (vám fungoval? ako ste postupovali?)
EN: i find some Firmware, but they are as 5001.img - but official instructions for use is bad ( was good for you? sa me how to pls)
SK:nejakým spôsobom som moj odpalil a nepomaha ani recovery.(trochu som sa hral a nemal som zalohu)
EN: I damaged original fimware(ROM), and recovery is not functional (I have no backup)
SKrípadne ak sa niekto hral s firmware a má nejaký funkčný inštalovateľný z SD a pod.....
EN: If someone has good firmware(ROM) fully functional, instalable from SD an so on. send me please.
SK:Možno by mi pomohol jednoduchý príkaz cez terminál
EN: Maybe will help command from terminal
Code:
ht tps:// docs .google. com/file/d/0BxgPttaVjg4gdklzN0tINlRCZWs/edit?usp=sharing
SK: a poslat mi komplet čo vypísal
EN: send me please what it show
Code:
dmesg
SK: Neni treba root.
EN: Root is not needed
SK: Ak chete root :
EN: If you want root:
Code:
ht tps:// docs. google. com/file/d/0BxgPttaVjg4gdl83TFdCb0h4WWc/edit?usp=sharing
SK: Ak ho máte rootnutý tak skusiť
EN: If you have it rooted please try
ROM DUMP
Code:
htt ps:// docs. google. com/file/d/0BxgPttaVjg4gVV9nLUNnWmtDMVk/edit?usp=sharing
SK: a poslať mi vzniknutý priečinok.
EN: and send me created output folder
SK: A teraz dôvod prečo to potrebujem
Vadil mi na tablete gtalk tak som ho zmazal a spôsobilo to že už som na nom nenaštartoval system.
tak som hladal nejaku možnosť preinštalovania nakolko mi ani recovery nepomohol.
Vyskúšal som tieto Firmware alebo ROm či jak to nazvať
EN: Why i need it?
I delete Gtalk and android crashed
I try those Firmawares(ROMs) :
Code:
ht tps:// docs. google. com/file/d/0BxgPttaVjg4gSnBsNjBScnZ5X0k/edit?usp=sharing
https://docs. google. com/file/d/0BxgPttaVjg4gZEdjTjJYQUJTT1k/edit?usp=sharing
SK:systém nabehol
dokonca aj android jelly bean
ale nefunguje dotykovka... nejak zlý ovládač alebo zle zdetekovanie.
EN: System is going, (jelly bean too) , BUT touch screen is not functional, bad driver or bad detected.
SK:Z mojho dmesg je zjavne že dotykovka proste nenabehne.. preto by možno stačil aj dmesg výpis a skúsil by som nastaviť tu inštalačku ROm tak aby nainštaloval správny ovládač.. ale neviem sa pohnúť. ak je niekto viac znalý v problematike tak prosím help.
moj dmesg vypíše:
EN: From my dmesg we see that touch screen has problems. Is there someone who can help what to do? maybe edit tryed ROMs will help.
My dmesg:
<1>[ 5.492059] wmt.sd2.param = 0:0
<1>[ 5.495873] Default wmt.sd3.param = 0:0
<1>[ 5.500390] do not have set uboot enviroment: wmt.init.rc
<7>[ 5.505914] Registered led device: lcd-backlight
<6>[ 5.510061] usbcore: registered new interface driver usbhid
<6>[ 5.515545] usbhid: USB HID core driver
<6>[ 5.520424] log enable:FF, setting:FF
<6>[ 5.524161] logger: created 256K log 'log_main'
<6>[ 5.528718] logger: created 256K log 'log_events'
<6>[ 5.533440] logger: created 64K log 'log_radio'
<6>[ 5.538052] GPS: mt3326_gps_power: Switching GPS device on
<6>[ 5.543461] GPS: mt3326_gps_power: ignore power control: 1
<6>[ 5.548913] GPS: mt3326_gps_probe: Registering chardev
<6>[ 5.554118] GPS: mt3326_gps_probe: major: 246, minor: 0
<6>[ 5.559465] GPS: mt3326_gps_probe: Done
<6>[ 5.563251] BTHWCTL: alloc bthwctl: 245:0
<6>[ 5.567733] BTHWCTL: Bluetooth hardware control driver initialized
<6>[ 5.574718] usbcore: registered new interface driver snd-usb-audio
<6>[ 5.588430] WMT_SOC: dai_name=i2s, codec_name=vt1603
<4>[ 5.596553] wmt_pdm_init: pcm_clk_src=73500
<4>[ 5.596559]
<6>[ 5.602926] VT1602: vt1602 string not found
<6>[ 5.607548] wmt.audio.i2s = vt1603:0
<6>[ 5.615507] WMT_SOC: create WMT-HWDEP 0 success
<6>[ 5.619993] mount_thread
<6>[ 5.625106] asoc: VT1603 <-> wmt-i2s.0 mapping ok
<4>[ 5.690401] buf_area = ffde0000, buf_addr = 32810000buf_area = ffd3c000, b
uf_addr = 32814000
<6>[ 5.698569] asoc: HWDAC <-> wmt-pdm.0 mapping ok
<6>[ 5.705486] ALSA device list:
<6>[ 5.708381] #0: WMT_SOC
<4>[ 5.711731] default disable oprofile
<6>[ 5.715477] nf_conntrack version 0.5.0 (12987 buckets, 51948 max)
<6>[ 5.723649] NF_TPROXY: Transparent proxy support initialized, version 4.1.
0
<6>[ 5.730528] NF_TPROXY: Copyright (c) 2006-2007 BalaBit IT Ltd.
<6>[ 5.737621] ip_tables: (C) 2000-2006 Netfilter Core Team
<6>[ 5.742955] TCP cubic registered
<6>[ 5.746714] NET: Registered protocol family 10
<6>[ 5.751925] ip6_tables: (C) 2000-2006 Netfilter Core Team
<6>[ 5.757353] IPv6 over IPv4 tunneling driver
<6>[ 5.761834] NET: Registered protocol family 17
<6>[ 5.766607] NET: Registered protocol family 15
<6>[ 5.771622] Bluetooth: RFCOMM TTY layer initialized
<6>[ 5.778068] Bluetooth: RFCOMM socket layer initialized
<6>[ 5.783324] Bluetooth: RFCOMM ver 1.11
<6>[ 5.786987] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
<6>[ 5.792273] Bluetooth: BNEP filters: protocol multicast
<6>[ 5.797472] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
<6>[ 5.805831] L2TP core driver, V2.0
<6>[ 5.809370] PPPoL2TP kernel driver, V2.0
<6>[ 5.813204] L2TP IP encapsulation support (L2TPv3)
<6>[ 5.818205] L2TP netlink interface
<6>[ 5.821558] L2TP ethernet pseudowire support (L2TPv3)
<6>[ 5.828702] L2TP debugfs support
<6>[ 5.832419] lib80211: common routines for IEEE802.11 drivers
<7>[ 5.838542] lib80211_crypt: registered algorithm 'NULL'
<6>[ 5.838552] VFP support v0.3: implementor 41 architecture 3 part 30 varian
t 9 rev 3
<6>[ 5.847145] ThumbEE CPU extension supported.
<5>[ 5.851866] Registering SWP/SWPB emulation handler
<6>[ 5.858031] input: kpadPower as /devices/virtual/input/input0
<4>[ 5.865118] [wmt_pm_init] id = 0x0, act = 0x1, bitmap = 0x6, ctl = 0xfe110
042, oc = 0xfe110082, od = 0xfe1100c2
<4>[ 5.875889] [wmt_pm_init] var define var_wake_en=1 var_wake_param=408001
<4>[ 5.882677] [wmt_pm_init] battery_used = 3
<6>[ 5.887464] PMC: WonderMedia Power Management driver
<4>[ 5.892537] PMC: Power button is configured as soft power
<4>[ 5.898238] [wmt_pm_init] power_on = 100 resume = 100 power_up = 100
<6>[ 5.905367] Can not find uboot env wmt.misc.param
<4>[ 5.910110] SD0 Host Clock 382812Hz
<6>[ 5.914246] Mali DRM initialize, driver name: mali_drm, version 2.1
<6>[ 5.920710] [drm] Initialized mali_drm 2.1.1 20101111 on minor 0
<4>[ 5.927980] Vt1609 touchscreen driver disabled.
<6>[ 5.934359] wmt-rtc wmt-rtc.0: setting system clock to 2013-03-06 13:51:31
UTC (1362577891)
<6>[ 5.943968] Freeing init memory: 180K
<4>[ 5.951254] init (1): /proc/1/oom_adj is deprecated, please use /proc/1/oo
m_score_adj instead.
<6>[ 6.043877] yaffs: dev is 32505866 name is "mtdblock10" rw
<6>[ 6.049288] yaffs: passed flags ""
<7>[ 6.052655] yaffs: yaffs: Attempting MTD mount of 31.10,"mtdblock10"
<7>[ 6.120439] yaffs: yaffs_read_super: is_checkpointed 1
<6>[ 6.120743] yaffs: dev is 32505868 name is "mtdblock12" rw
<6>[ 6.126153] yaffs: passed flags ""
<7>[ 6.129521] yaffs: yaffs: Attempting MTD mount of 31.12,"mtdblock12"
<7>[ 6.213933] yaffs: block 191 is bad
<7>[ 6.763771] yaffs: yaffs_read_super: is_checkpointed 0
<6>[ 6.763954] yaffs: dev is 32505867 name is "mtdblock11" rw
<6>[ 6.769369] yaffs: passed flags ""
<7>[ 6.772737] yaffs: yaffs: Attempting MTD mount of 31.11,"mtdblock11"
<7>[ 6.776632] yaffs: yaffs_read_super: is_checkpointed 1
<4>[ 6.801544] Uncor Ecc Err 0_th, on page 0x13828 fail., cur_try_time=-1
<4>[ 6.809506] Uncor Ecc Err 1_th, on page 0x13828 fail., cur_try_time=0
<4>[ 6.817395] read retry PASS cur_try_times=1
<4>[ 6.825528] Uncor Ecc Err 0_th, on page 0x13827 fail., cur_try_time=1
<4>[ 6.833413] read retry PASS cur_try_times=2
<4>[ 6.841893] Uncor Ecc Err 0_th, on page 0x1382a fail., cur_try_time=2
<4>[ 6.849840] Uncor Ecc Err 1_th, on page 0x1382a fail., cur_try_time=3
<4>[ 6.856956] read retry PASS cur_try_times=4
<4>[ 6.890837] UMP: UMP device driver loaded
<4>[ 6.934001] Mali: Mali device driver loaded
<6>[ 7.075362] [wmt-vd] WonderMedia HW decoder driver inited
<6>[ 7.084773] [wmt-lock] init ok, major=242, minor=1
<6>[ 7.097948] [wmt-vd] jdec Request IRQ 64 Ok.
<6>[ 7.102145] [wmt-vd] jdec registered major 236 minor 1
<6>[ 7.111142] [wmt-vd] mpeg2 registered major 236 minor 2
<6>[ 7.120189] [wmt-vd] mpeg4 registered major 236 minor 3
<6>[ 7.129287] [wmt-vd] divx registered major 236 minor 4
<6>[ 7.138294] [wmt-vd] h263 registered major 236 minor 8
<6>[ 7.167623] [wmt-vd] h264 registered major 236 minor 5
<6>[ 7.175695] [wmt-vd] vc1 registered major 236 minor 7
<6>[ 7.183105] [wmt-vd] rv registered major 236 minor 6
<6>[ 7.206193] [wmt-vd] vpx Request IRQ 88 Ok.
<6>[ 7.210310] [wmt-vd] vpx registered major 236 minor 9
<7>[ 7.221249] [wmt-ve] videoencoder_init: create video encoder proc
<4>[ 7.221261] start register videoencoder_driver
<4>[ 7.225967] *****NOW start videoencoder probe function!!*****
<6>[ 7.231852] [wmt-ve] veinfo.prdt_virt =0xffd00000,veinfo.prdt_phys =0x32a6
0000
<6>[ 7.238998] [wmt-ve] prob /dev/wmt-ve major 236, minor 0, prdt ffd00000/32
a60000, size 100 KB
<4>[ 7.247486] register videoencoder_driver done
<6>[ 7.251805] [wmt-ve] WonderMedia HW encoder driver inited
<6>[ 7.264022] [wmt-ve] encoder->irq_num = 87,encoder->isr = 0xbf0a62a8
<6>[ 7.270413] [wmt-ve] wmt-h264enc Request IRQ 87 Ok.
<6>[ 7.275237] [wmt-ve] wmt-h264enc registered major 236 minor 18
<4>[ 7.318073] wmt_vid_i2c_probe()
<3>[ 7.325354] WonderMedia CMOS camera register OK
<4>[ 7.657136] Uncor Ecc Err 0_th, on page 0x27ff0 fail., cur_try_time=4
<4>[ 7.665092] read retry PASS cur_try_times=5
<4>[ 7.689184] Uncor Ecc Err 0_th, on page 0x27fee fail., cur_try_time=5
<4>[ 7.697484] Uncor Ecc Err 1_th, on page 0x27fee fail., cur_try_time=6
<4>[ 7.705109] read retry PASS cur_try_times=-1
<3>[ 7.717347] init: try to config ril modem type...
<3>[ 7.721823] init: ril is not enable...Uncor Ecc Err 0_th, on page 0x2573c
fail., cur_try_time=-1
<4>[ 7.769700] Uncor Ecc Err 1_th, on page 0x2573c fail., cur_try_time=0
<4>[ 7.777596] read retry PASS cur_try_times=1
<3>[ 7.989003] init: cannot find '/system/etc/install-recovery.sh', disabling
'flash_recovery'
<3>[ 8.233007] init: cannot find '/system/etc/init.sh', disabling 'system_ini
t'
<3>[ 8.350094] android_usb: already disabled
<6>[ 8.354709] adb_bind_config
<6>[ 8.357444] usb_ep_autoconfig try to find ep1in-bulk
<6>[ 8.362447] usb_ep_autoconfig found ep1in-bulk
<6>[ 8.366953] usb_ep_autoconfig try to find ep2out-bulk
<6>[ 8.372070] usb_ep_autoconfig found ep2out-bulk
<6>[ 8.376846] udc: gri wmt_pullup()
<6>[ 8.380088] udc: gri pullup_enable()
<6>[ 8.385135] warning: `adbd' uses 32-bit capabilities (legacy support in us
e)
<6>[ 8.392382] adb_open
<6>[ 8.555107] android_work: sent uevent USB_STATE=CONNECTED
<6>[ 8.638176] android_usb gadget: high speed config #1: android
<6>[ 8.643884] rndis ooooo 24
<6>[ 8.646556] android_work: sent uevent USB_STATE=CONFIGURED
<6>[ 8.906307] rndis xxxxx 24
<6>[ 9.350776] usbcore: registered new interface driver cdc_acm
<6>[ 9.356380] cdc_acm: USB Abstract Control Model driver for USB modems and
ISDN adapters
<6>[ 9.469677] USB Serial support registered for GSM modem (1-port)
<6>[ 9.475907] usbcore: registered new interface driver option
<6>[ 9.481418] option: v0.7.2:USB Driver for GSM modems
<1>[ 9.535094] [is_mc32x0]: Find mc3230(mCube g-sensor).
<6>[ 9.542536] input: g-sensor as /devices/virtual/input/input1
<4>[ 9.567353] offser gain = 482 474 418 528 256 688======================
<4>[ 9.567361]
<4>[ 9.567364] ft5406-touch reslx=600, resly=1024, Interrupt GP1, bit1, Rese
t GP0, bit4
<6>[ 9.768922] input: ft5406-touch as /devices/virtual/input/input2
<4>[ 9.793322] ERR:ft5x0x_i2c_rxdata_67:msg i2c read error: -5
<4>[ 9.798824] ERR:ft5x0x_read_data_157:read_data i2c_rxdata failed: -5
<1>[ 9.986959] [dump_kpad_devinfo]: =========================================
==========
<1>[ 9.994639] [dump_kpad_devinfo]: kpad id:baseboard devnum:1
<1>[ 10.000172] [dump_kpad_devinfo]: dev[0] type:rc_1
<1>[ 10.005104] [dump_kpad_devinfo]:
<1>[ 10.008390] [dump_kpad_devinfo]: key number:5
<1>[ 10.012810] [dump_kpad_devinfo]: key0:9e(158),
<1>[ 10.017152] [dump_kpad_devinfo]: key1:8b(139),
<1>[ 10.021655] [dump_kpad_devinfo]: key2:73(115),
<1>[ 10.026157] [dump_kpad_devinfo]: key3:72(114),
<1>[ 10.030666] [dump_kpad_devinfo]: key4:66(102),
<1>[ 10.035167] [dump_kpad_devinfo]:
<1>[ 10.038638] [dump_kpad_devinfo]: longkey num:0
<1>[ 10.043142] [dump_kpad_devinfo]: =========================================
==========
<6>[ 10.053519] input: keypad as /devices/virtual/input/input3
<4>[ 10.430673] fan GEIO_STOP_LOGO
<6>[ 10.433659] [Boot Animation] animation_stop
<4>[ 10.776949] [VPP] rx user pid 0x55
<4>[ 12.439302] mc_write:3--0
<4>[ 12.442012] mc_write:3--0
<4>[ 12.520929] [INFO] {wmt_vid_open}: vid_i2c_gpio_en 0x00000000
<4>[ 12.527775] cmos_init_gc0308 2560 1936
<4>[ 12.626609] cmos_release()
<4>[ 12.629423] [INFO] {wmt_vid_open}: vid_i2c_gpio_en 0x00000000
<4>[ 12.659689] cmos_init_yacd511 2560 1936
<4>[ 12.663553] cmos_release()
<6>[ 12.932817] [INFO] VPU Firmware Version =>
<6>[ 12.932823] product : | version : 0002.0000.00000008
<6>[ 12.932829]
<6>[ 12.947243] [INFO] msvd_dec_open(h264) bf057d54 (index 0 inUse 1)
<6>[ 12.954723] [INFO] Profile 0x4d Level 0x15 Interlace AspectRateio 0x0
<4>[ 13.060117] mc_write:3--5
<6>[ 13.064871] [INFO] VPU Firmware Version =>
<6>[ 13.064877] product : | version : 0002.0000.00000008
<6>[ 13.064883]
<6>[ 13.079297] [INFO] msvd_dec_open(h264) bf057d54 (index 0 inUse 1)
<6>[ 13.086704] [INFO] Profile 0x4d Level 0x15 Interlace AspectRateio 0x0
<4>[ 22.439434] Uncor Ecc Err 0_th, on page 0x2567e fail., cur_try_time=1
<4>[ 22.447430] Uncor Ecc Err 1_th, on page 0x2567e fail., cur_try_time=2
<4>[ 22.455322] read retry PASS cur_try_times=3
<1>[ 33.393832] [lcd_brightness]pwm_no = 0 pwm_period = 1000 b= 0
<4>[ 33.399504] skip adjust backlight at the first time
<4>[ 33.404539] mc_write:1--0
<6>[ 33.419512] request_suspend_state: wakeup (3->0) at 33849036002 (2013-03-0
6 13:51:58.986161334 UTC)
<1>[ 33.430339] [lcd_brightness]pwm_no = 0 pwm_period = 1000 b= 154
<4>[ 33.440196] mc_write:1--60
<6>[ 34.008832] acc_open
<6>[ 34.011157] acc_release
<4>[ 34.303820] Uncor Ecc Err 0_th, on page 0x25800 fail., cur_try_time=3
<4>[ 34.310838] read retry PASS cur_try_times=4
<4>[ 40.754027] mc_write:3--0
<3>[ 40.778421] binder: release proc 162, transaction 90, not freed
<3>[ 40.784294] binder: release proc 162, transaction 5047, not freed
<6>[ 40.884850] yaffs: dev is 32505869 name is "mtdblock13" rw
<6>[ 40.890290] yaffs: passed flags ""
<7>[ 40.893639] yaffs: yaffs: Attempting MTD mount of 31.13,"mtdblock13"
<7>[ 41.008158] yaffs: yaffs_read_super: is_checkpointed 1
<4>[ 44.126783] Uncor Ecc Err 0_th, on page 0x27fbc fail., cur_try_time=4
<4>[ 44.275513] read retry PASS cur_try_times=5
<4>[ 44.493885] Uncor Ecc Err 0_th, on page 0x27fbe fail., cur_try_time=5
<4>[ 44.524878] Uncor Ecc Err 1_th, on page 0x27fbe fail., cur_try_time=6
<4>[ 44.533376] read retry PASS cur_try_times=-1
<4>[ 46.592229] Uncor Ecc Err 0_th, on page 0x43944 fail., cur_try_time=-1
<4>[ 46.610250] Uncor Ecc Err 1_th, on page 0x43944 fail., cur_try_time=0
<4>[ 46.630067] read retry PASS cur_try_times=1
<4>[ 46.910741] Uncor Ecc Err 0_th, on page 0x43946 fail., cur_try_time=1
<4>[ 46.918700] Uncor Ecc Err 1_th, on page 0x43946 fail., cur_try_time=2
<4>[ 46.926723] read retry PASS cur_try_times=3
<4>[ 48.368608] Uncor Ecc Err 0_th, on page 0x25900 fail., cur_try_time=3
<4>[ 48.376529] read retry PASS cur_try_times=4
<4>[ 333.801387] Uncor Ecc Err 0_th, on page 0x25b00 fail., cur_try_time=4
<4>[ 333.809262] Uncor Ecc Err 1_th, on page 0x25b00 fail., cur_try_time=5
<4>[ 333.817127] Uncor Ecc Err 2_th, on page 0x25b00 fail., cur_try_time=6
<4>[ 333.824996] Uncor Ecc Err 3_th, on page 0x25b00 fail., cur_try_time=-1
<4>[ 333.832908] read retry PASS cur_try_times=0
<4>[ 333.840808] Uncor Ecc Err 0_th, on page 0x25b00 fail., cur_try_time=0
<4>[ 333.848720] Uncor Ecc Err 1_th, on page 0x25b00 fail., cur_try_time=1
<4>[ 333.856625] Uncor Ecc Err 2_th, on page 0x25b00 fail., cur_try_time=2
<4>[ 333.864500] Uncor Ecc Err 3_th, on page 0x25b00 fail., cur_try_time=3
<4>[ 333.871615] read retry PASS cur_try_times=4
<1>[ 633.830513] [lcd_brightness]pwm_no = 0 pwm_period = 1000 b= 150
<4>[ 633.836406] mc_write:1--58
<1>[ 633.846984] [lcd_brightness]pwm_no = 0 pwm_period = 1000 b= 147
<4>[ 633.852891] mc_write:1--57
<1>[ 633.866863] [lcd_brightness]pwm_no = 0 pwm_period = 1000 b= 144
<4>[ 633.872757] mc_write:1--56
<1>[ 633.886870] [lcd_brightness]pwm_no = 0 pwm_period = 1000 b= 141
<4>[ 633.894230] mc_write:1--55
<1>[ 633.903615] [lcd_brightness]pwm_no = 0 pwm_period = 1000 b= 138
<4>[ 633.909819] mc_write:1--54
<1>[ 633.920203] [lcd_brightness]pwm_no = 0 pwm_period = 1000 b= 135
<4>[ 633.926096] mc_write:1--52
<1>[ 633.936835] [lcd_brightness]pwm_no = 0 pwm_period = 1000 b= 132
<4>[ 633.942719] mc_write:1--51
<1>[ 633.953646] [lcd_brightness]pwm_no = 0 pwm_period = 1000 b= 129
<4>[ 633.959562] mc_write:1--50
<1>[ 633.970201] [lcd_brightness]pwm_no = 0 pwm_period = 1000 b= 126
<4>[ 633.976094] mc_write:1--49
<1>[ 633.986882] [lcd_brightness]pwm_no = 0 pwm_period = 1000 b= 123
<4>[ 633.992769] mc_write:1--48
<1>[ 634.006991] [lcd_brightness]pwm_no = 0 pwm_period = 1000 b= 120
<4>[ 634.013487] mc_write:1--47
<1>[ 634.026882] [lcd_brightness]pwm_no = 0 pwm_period = 1000 b= 117
<4>[ 634.032772] mc_write:1--45
<1>[ 634.046842] [lcd_brightness]pwm_no = 0 pwm_period = 1000 b= 114
<4>[ 634.054196] mc_write:1--44
<1>[ 634.063611] [lcd_brightness]pwm_no = 0 pwm_period = 1000 b= 111
<4>[ 634.069806] mc_write:1--43
<1>[ 634.080537] [lcd_brightness]pwm_no = 0 pwm_period = 1000 b= 108
<4>[ 634.086431] mc_write:1--42
<1>[ 634.096848] [lcd_brightness]pwm_no = 0 pwm_period = 1000 b= 105
<4>[ 634.102729] mc_write:1--41
<1>[ 634.113656] [lcd_brightness]pwm_no = 0 pwm_period = 1000 b= 102
<4>[ 634.119662] mc_write:1--40
<1>[ 634.130198] [lcd_brightness]pwm_no = 0 pwm_period = 1000 b= 100
<4>[ 634.136083] mc_write:1--39
<1>[ 641.271927] [lcd_brightness]pwm_no = 0 pwm_period = 1000 b= 0
<1>[ 641.277631] [lcd_brightness]lcd turn off <--
<4>[ 641.283652] mc_write:1--0
<6>[ 641.292736] request_suspend_state: sleep (0->3) at 641722369336 (2013-03-0
6 14:02:06.859382668 UTC)
<4>[ 641.405636] -------------> do auto suspend
<3>[ 2132.167123] init: untracked pid 1061 exited
[email protected]:/ $
Click to expand...
Click to collapse
SK:dikes
ENG:thank you
ROM
SK:
Dnes som nasiel origo ROM
Ale nepodarilo sa mi to nahodit ani podla instrukcii
ENG: Today I find original shipped ROM. But, I have problem with upgrade it by the instructions.
Anyone knowns how to make jelly bean working?
Any one?..
Q&A for [ROM] RK3188 Tab V88 by Oma rocks !
Some developers prefer that questions remain separate from their main development thread to help keep things organized. Placing your question within this thread will increase its chances of being answered by a member of the community or by the developer. Thanks for understanding and for helping to keep XDA neat and tidy! :smile:
the display orientation is wrong.
Click to expand...
Click to collapse
Download fix for Vido mini one zz from RK3188: V88 by Oma – KitKat 4.4.4 Edition (Sry this is my first post. I can't use links)
I have one problem. In Vido N80RK (rom: RK3188: V88 by Oma – KitKat 4.4.4 Edition ) WIFI not working. Why. I have Fix for Vido n80rk from Omnirom 4.4.4 and fix for Vido mini one zz.
Chuwi V88
You'll do android 5.0 on Chuwi V88 and if so, when. Thank you
Maybe chuwi itself provide 5.0 update
chuwi v88 quad
Hello. Can you tell me where I can install on my root Chuwi V88 quad? Thanks
Any chance of running the WiFi Chuwi 1st edition v88?
Hi oma.
in the woxter nimbus 98q does not work the wiffi and rotation in CM11, omnirom and lollipop. Can you help.
Thank you.
dmesg: https://mega.co.nz/#!fBA23TrK!VKQ9VEBYJP2ZZNunXSuv0nbyHUk5xRYXWcmbwuPsUT4
unknown clone RK3188 firmware selection
Please help me decide which firmware should I flash to clone that matches V88HD i guess.
The tablet has only two buttons, BACK and POWER. I already rooted and install CWM recovery following instruction in the head post.
CWM recovery is working great with gestures. I haven't seen that before.
Now I'm selecting ROM to FLASH for the first time on this device and a little nervous about it.
I need to change ROM, because of huge instability of WLAN. I hope it is ROM issue.
Tablet is sold in Bulgaria under with manufacturer AKKRON. Model is called qr10a16bt
Technical/Marketing SPECS
Touch Screen Size 9.7'' (4:3) Multi touch Retina panel
Density 320dpi
Resolution 2548 X 1536
Multi-touch support 10 finger multi-touch support
Casing Material Metal rear panel
Dimensions 242 x 189 x 9.9mm
Weight 0.64 Kgs
Chipset, CPU
chipset solution Rockchip 3188, cortex A9 Quad Core
processor speed 1.8 GHz
Memory
RAM 2 GB DDR3
NAND Flash 16 GB
Micro SD Card slot Support up to 32GB Micro SD
Camera
Front and Rear cameras 0.3 Mpix Front and 5.0 Mpix Rear
Interfaces
WIFI 802.11 b/g/n
Bluetooth Bluetooth v2.1
USB 1x USB
Micro SD card 1x Micro SD card slot (up to 32GB)
HDMI (Full HD) 1x HDMI, HD Video decoder support 1080p and 2160p
OTG Yes
supports external keyboard Yes
Earphone Out 1x Stereo Earphone Out
Audio output Speaker 1W
System
Operating system Android 4.2
Menu Language Bulgarian/English/Russian/German/Spanish/French ...
Support Flash player Flash 11
Support Office software Word, Excel, PDF, TXT ect.
Messenger MSN, Skype, Facebook, Twitter, Google talk, E-mail, ect.
E-Book Yes
Game support Yes
Video AVI, MKV, RM, RMVB, MPEG1/2/4, ect.
Audio MP3, WMA, AC3, WAV ect.
Audio / Video Recording Yes
3D by internal Hardware Yes
G Sensor Yes, 4 sides G-sensor
Power
power supply Aadaptor: 100v~240v, 50hz-60hz, 5V 1.5A
Battery 8000 mAh Rechargeable Lithium Polymer
Battery workimg time 8-16 Hours
Accessory
USB Cable for computer 1x
USB cable for USB disk 1x
User Manaul 1x
Adaptor 1x
Packaging
Box Dimensions (H?W?D)mm 302 x 200 x 76
Box Weight (Net/ Gross)
0.72 / 1.36 Kgs
this is device dmesg. Strangely it begins from 9.4 sec?
<6>[ 9.449500] Bluetooth: RFCOMM socket layer initialized
<6>[ 9.449530] Bluetooth: RFCOMM ver 1.11
<6>[ 9.449552] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
<6>[ 9.449585] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
<6>[ 9.449713] NET: Registered protocol family 35
<6>[ 9.449861] [BT_RFKILL]: Enter rfkill_rk_init
<6>[ 9.449959] [BT_RFKILL]: Failed to get bt_default_reset gpio.
<4>[ 9.449998] rfkill_rk: probe of rfkill_rk failed with error -1
<6>[ 9.696096] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
<3>[ 9.696264] rk_cam_cif(3093):rk3066b-camera version: v0.3.9 Zoom by ipp
<5>[ 9.696293] Registering SWP/SWPB emulation handler
<6>[ 9.697534] ddrfreq: verion 2.4 20130427
<6>[ 9.697610] ddrfreq: normal 528MHz video 0MHz dualview 0MHz idle 0MHz suspend 198MHz reboot 300MHz
<6>[ 9.699432] ddrfreq: change freq to 528 MHz when normal
<6>[ 9.700842] i2c i2c-0: sensor_probe: gs_mma8452,0xde60ca00
<4>[ 9.701212] sensor_chip_init:gs_mma8452:devid=0x2a,ops=0xc0e48dc8
<6>[ 9.703501] input: gsensor as /devices/platform/rk30_i2c.0/i2c-0/0-001d/input/input2
<4>[ 9.704043] sensor_irq_init:use irq=175
<4>[ 9.704341] sensor_misc_device_register:miscdevice: mma8452_daemon
<4>[ 9.704424] sensor_probe:initialized ok,sensor name:mma8452,type:1,id=14
<4>[ 9.704447]
<6>[ 9.704565] i2c i2c-0: sensor_probe: gs_lis3dh,0xde60cc00
<3>[ 9.704919] i2c i2c-0: No ack, Maybe slave(addr: 0x19) not exist or abnormal power-on, retry 2...
<3>[ 9.705317] i2c i2c-0: No ack, Maybe slave(addr: 0x19) not exist or abnormal power-on, retry 1...
<3>[ 9.705681] i2c i2c-0: No ack, Maybe slave(addr: 0x19) not exist or abnormal power-on, retry 0...
<3>[ 9.706044] i2c i2c-0: No ack, Maybe slave(addr: 0x19) not exist or abnormal power-on, retry 2...
<3>[ 9.706410] i2c i2c-0: No ack, Maybe slave(addr: 0x19) not exist or abnormal power-on, retry 1...
<3>[ 9.706775] i2c i2c-0: No ack, Maybe slave(addr: 0x19) not exist or abnormal power-on, retry 0...
<3>[ 9.707145] i2c i2c-0: No ack, Maybe slave(addr: 0x19) not exist or abnormal power-on, retry 2...
<3>[ 9.707510] i2c i2c-0: No ack, Maybe slave(addr: 0x19) not exist or abnormal power-on, retry 1...
<3>[ 9.707875] i2c i2c-0: No ack, Maybe slave(addr: 0x19) not exist or abnormal power-on, retry 0...
<4>[ 9.707982] sensor_chip_init:fail to read gs_lis3dh devid:0xff
<3>[ 9.708058] i2c i2c-0: sensor_probe failed -11
<3>[ 9.708075]
<4>[ 9.708150] sensors: probe of 0-0019 failed with error -11
<6>[ 9.708331] sensor_init: Probe name sensors
<4>[ 9.708415] sensor-dev.c v1.3 add sensor debug support 2013-3-15
<6>[ 9.709575] rtc_hym8563 1-0051: setting system clock to 2014-11-20 13:40:30 UTC (1416490830)
<6>[ 9.714097] asoc: rk-hdmi-i2s-hifi <-> rk29_i2s.1 mapping ok
<6>[ 9.716488] Freeing init memory: 3240K
<4>[ 9.744345] init (1): /proc/1/oom_adj is deprecated, please use /proc/1/oom_score_adj instead.
<6>[ 9.937499] keychord: using input dev rk29-keypad for fevent
<3>[ 9.937689] init: cannot open '/initlogo.rle'
<4>[ 10.285675] min_w = 800,min_h = 600 ,max_real_w = 2592,max_real_h = 1944,max_w = 2592,max_h =1944
<4>[ 10.298449] gp_rknand_info = : 0xdd48d000
<4>[ 10.298516] rk30_chip_set:1
<4>[ 10.298565] request IRQ_NANDC irq , ret=0.........
<4>[ 10.298596] FTL INFO:Version = 438,Date = 20130620
<4>[ 10.298658] FlashCopyProgBuf1=0xc17ca000
<4>[ 10.298697] ATime: 40 ns AHB: 140 timming: 1081
<4>[ 10.298721] No.1 FLASH INFO:ad de 94 da 74
<4>[ 10.298746] No.3 FLASH INFO:ad de 94 da 74
<4>[ 10.299143] ATime: 32 ns AHB: 140 timming: 1061
<4>[ 10.299353] ATime: 32 ns AHB: 140 timming: 1061
<4>[ 10.299373] randomizer = 2 , EccBits = 28 pSpec->pReadRetrial = bf00a9a8
<4>[ 10.402590] totalLogicBlkRaw = 3946
<4>[ 10.402617] gBootMedia = 1 gSdmmcFwPartOffset =0!
<4>[ 10.402645] rknand_buffer.c version: 4.38 20121130!
<5>[ 10.402744] 10 cmdlinepart partitions found on MTD device rk29xxnand
<5>[ 10.402773] Creating 10 MTD partitions on "rk29xxnand":
<5>[ 10.402803] 0x000000400000-0x000000800000 : "misc"
<5>[ 10.403530] 0x000000800000-0x000001800000 : "kernel"
<5>[ 10.404162] 0x000001800000-0x000002800000 : "boot"
<5>[ 10.404758] 0x000002800000-0x000004800000 : "recovery"
<5>[ 10.405422] 0x000004800000-0x000008800000 : "backup"
<5>[ 10.406091] 0x000008800000-0x000010800000 : "cache"
<5>[ 10.406792] 0x000010800000-0x000050800000 : "userdata"
<5>[ 10.407962] 0x000050800000-0x000050c00000 : "kpanic"
<6>[ 10.409439] apanic: Bound to mtd partition 'kpanic'
<6>[ 10.409462] apanic: No panic data available
<5>[ 10.409590] 0x000050c00000-0x000070c00000 : "system"
<5>[ 10.410501] 0x000070c00000-0x0003da800000 : "user"
<4>[ 10.418466] startBlk = 44 sysProtAddr = 43
<6>[ 10.523689] EXT4-fs (mtdblock8): mounted filesystem with ordered data mode. Opts: noauto_da_alloc
<6>[ 10.588011] EXT4-fs (mtdblock6): mounted filesystem with ordered data mode. Opts: noauto_da_alloc
<6>[ 10.701857] EXT4-fs (mtdblock5): mounted filesystem with ordered data mode. Opts: noauto_da_alloc
<4>[ 10.875180] Probe ov5640_back_3 success
<3>[ 12.015221] camera 33-1-nt99340_back_4: Probe nt99340_back_4 failed
<3>[ 13.155202] camera 33-2-gc0328_front_5: Probe gc0328_front_5 failed
<4>[ 13.745940] min_w = 640,min_h = 480 ,max_real_w = 640,max_real_h = 480,max_w = 640,max_h =480
<4>[ 14.315213] Probe gc0308_front_6 success
<3>[ 14.905641] i2c i2c-3: 1 i2c clients have been registered at 0x3cmin_w = 800,min_h = 600 ,max_real_w = 1600,max_real_h = 1200,max_w = 1600,max_h =1200
<3>[ 14.946197] gc2035_front_7(rk_cam_sensor:677): error: mismatched pid = 0x0
<3>[ 14.946223]
<6>[ 15.265195] DWC_OTG: dwc_otg_hcd_enable, disable host controller
<3>[ 15.495228] camera 33-4-gc2035_front_7: Probe gc2035_front_7 failed
<4>[ 15.495588] UMP: Using dedicated memory backend
<4>[ 15.495653] UMP: Requesting dedicated memory: 0x86800000, size: 268435456
<4>[ 15.495852] UMP: UMP device driver loaded
<4>[ 15.528458] Mali: Mali400 inside of rk3188!
<4>[ 15.528491] Mali: mali freq table num : 6
<4>[ 15.528514] Mali: mali freq table :Mali: 128,Mali: 198,Mali: 256,Mali: 297,Mali: 384,Mali: 594,Mali:
<4>[ 15.528573] Mali: init mali clock success
<4>[ 15.534174] Mali: [MENTION=5839521 [MENTION=1065870 [user=1879310]@@@@[/user][/MENTION][/MENTION]@Mali device driver loaded success [MENTION=5839521 [MENTION=1065870 [user=1879310]@@@@[/user][/MENTION][/MENTION]@
<4>[ 15.539838] mirroring: Unknown symbol video_data_to_mirroring (err 0)
<4>[ 15.539895] mirroring: Unknown symbol audio_data_to_mirroring (err 0)
<4>[ 15.542228] rk29_ipp: module is from the staging directory, the quality is unknown, you have been warned.
<4>[ 15.543039] ipp irq 47
<4>[ 15.543308] IPP init, version rk30-ipp 1.003
<3>[ 15.605465] init: cannot find '/system/vendor/bin/pvrsrvctl', disabling 'pvrsrvctl'
<3>[ 15.706706] init: cannot find '/system/etc/install-recovery.sh', disabling 'flash_recovery'
<3>[ 15.726673] init: cannot find '/system/bin/jellyservice', disabling 'jelly'
<3>[ 15.726750] init: cannot find '/system/bin/mtvmfservice', disabling 'mtvmf'
<3>[ 15.728971] init: cannot find '/system/bin/bplus_helper', disabling 'bplus_helper'
<3>[ 15.734750] VPU_SERVICE: failed on clk_get pd_video
<4>[ 15.734794] vpu: power on
<6>[ 15.734843] VPU_SERVICE: checking hw id 4831
<4>[ 15.735579] vpu: power off...done
<6>[ 15.735616] VPU_SERVICE: init success
<3>[ 15.799970] init: property 'ro.serialno' doesn't exist while expanding '${ro.serialno}'
<3>[ 15.800037] init: cannot expand '${ro.serialno}' while writing to '/sys/class/android_usb/android0/iSerial'
<3>[ 15.800332] init: using deprecated syntax for specifying property 'ro.product.usbfactory', use ${name} instead
<3>[ 16.046970] android_usb: already disabled
<3>[ 16.047154] android_usb: already disabled
<6>[ 16.055763] adb_open
<4>[ 16.193743] [rknand_sys_storage_ioctl:90] rknand_sys_storage_ioctl in
<4>[ 16.193790] [rknand_sys_storage_ioctl:103] RKNAND_GET_DRM_KEY
<4>[ 16.193831] [rknand_sys_storage_ioctl:365] return ret = 0
<6>[ 16.276041] .428.. MMC0 receive the message sd-No-Media from VOLD.[sd_mmc]
<6>[ 16.276077] .459.. MMC0 receive the message No-Media from VOLD. waitTimes=0 [sd_mmc]
<4>[ 16.777532] rk fb use 3 buffers
<6>[ 16.813409] lcdc0 win1 open,atv layer:2
<6>[ 16.815193] lcdc0 win1 closed,atv layer:1
<6>[ 16.957703] rk30-lcdc rk30-lcdc.0: blank mode:0
<3>[ 17.092382] ov5640_back_3(rk_cam_sensor:1140): generic_sensor_ioctl cmd(0x3) is unknown !
<3>[ 17.092391]
<3>[ 17.092671] gc0308_front_6(rk_cam_sensor:1140): generic_sensor_ioctl cmd(0x3) is unknown !
<3>[ 17.092679]
<6>[ 23.095170] DWC_OTG: ********vbus detect*********************************************
<6>[ 23.321140] DWC_OTG: ********soft connect!!!*****************************************
<6>[ 23.327139] DWC_OTG: USB SUSPEND
<6>[ 23.450279] DWC_OTG: USB RESET
<6>[ 23.538606] android_work: sent uevent USB_STATE=CONNECTED
<6>[ 23.542829] DWC_OTG: USB RESET
<6>[ 23.659870] android_usb gadget: high speed config #1: android
<6>[ 23.660030] android_work: sent uevent USB_STATE=CONFIGURED
<6>[ 25.460147] warning: `zygote' uses 32-bit capabilities (legacy support in use)
<6>[ 40.576548] request_suspend_state: wakeup (3->0) at 40521400256 (2014-11-20 13:41:01.358672629 UTC)
<4>[ 41.125827] initRssiHistory.
<4>[ 41.125861] =======================================================
<4>[ 41.125911] ==== Launching Wi-Fi driver! (Powered by Rockchip) ====
<4>[ 41.125949] =======================================================
<4>[ 41.125989] MT5931 SDIO WiFi driver (Powered by Rockchip,Ver 3.12) init.
<4>[ 41.126029] ## Calling platform_driver_register
<4>[ 41.126121] ## wifi_probe
<4>[ 41.126245] wifi_set_power = 1
<6>[ 41.126270] rk29sdk_wifi_power: 1
<6>[ 41.239065] acc_open
<6>[ 41.239113] acc_release
<6>[ 41.423877] wifi turn on power
<4>[ 41.475210] wifi_set_carddetect = 1
<6>[ 41.475242] rk29sdk_wifi_set_carddetect:1
<6>[ 41.475291] mmc1: slot status change detected(0-1)
<4>[ 41.475828] wl_android_wifictrl_func_add success.
<6>[ 41.675227]
<6>[ 41.675234] drivers/mmc/core/core.c...1824.. ===== mmc_rescan Begin....[mmc1]
<6>[ 41.719148]
<6>[ 41.719157] mmc_attach_sdio..808.. ===== Begin to identify card as SDIO-card. [mmc1]
<6>[ 41.749674] rk29_sdmmc_change_clk_div..1961.. newDiv=0, newCLK=24000Khz [sdio]
<6>[ 41.752956] mmc1: new high speed SDIO card at address 0001
<6>[ 43.497995] mmc_rescan_try_freq..1675.. ===== Initialize SDIO successfully. [mmc1]
<4>[ 43.588606] Current WiFi chip is MT5931.
<4>[ 43.588759] p2p Launch
<4>[ 43.588781] glRegisterP2P
<4>[ 43.589077] Launch success, fgIsP2PRegistered TRUE.
<6>[ 45.785453] ADDRCONF(NETDEV_UP): wlan0: link is not ready
<4>[ 46.563847] initRssiHistory.
<6>[ 46.573200] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
<4>[ 49.511009] --> mtk_cfg80211_testmode_cmd()
<4>[ 49.515282] --> mtk_cfg80211_testmode_sw_cmd()
<4>[ 49.519261] --> mtk_cfg80211_testmode_cmd()
<4>[ 49.519295] --> mtk_cfg80211_testmode_sw_cmd()
<4>[ 49.519530] --> mtk_cfg80211_testmode_cmd()
<4>[ 49.519560] --> mtk_cfg80211_testmode_sw_cmd()
<4>[ 49.519835] --> mtk_cfg80211_testmode_cmd()
<4>[ 49.519880] --> mtk_cfg80211_testmode_sw_cmd()
<4>[ 49.520126] --> mtk_cfg80211_testmode_cmd()
<4>[ 49.520155] --> mtk_cfg80211_testmode_sw_cmd()
<4>[ 49.520365] --> mtk_cfg80211_testmode_cmd()
<4>[ 49.520418] --> mtk_cfg80211_testmode_sw_cmd()
<7>[ 56.955207] p2p0: no IPv6 routers present
<7>[ 57.335174] wlan0: no IPv6 routers present
<3>[ 64.074180] init: sys_prop: permission denied uid:1003 name:service.bootanim.exit
<6>[ 74.725928] rk30-lcdc rk30-lcdc.0: blank mode:4
<6>[ 74.726411] request_suspend_state: sleep (0->3) at 74671267635 (2014-11-20
13:41:35.508540758 UTC)
<6>[ 74.726823] *********wlanP2P_early_suspend************
<6>[ 74.726865] *********p2pEarlySuspend************
<6>[ 74.726907] ip is not avaliable.
<4>[ 74.774951] rk3188 lcdc0 clk disable...
<6>[ 74.875759] ddrfreq: change auto self refresh to 1 when suspend
<6>[ 74.877214] ddrfreq: change freq to 198 MHz when suspend
<6>[ 86.091258] EXT4-fs (mtdblock8): re-mounted. Opts: (null)
<6>[ 86.109331] EXT4-fs (mtdblock8): re-mounted. Opts: (null)
<6>[ 86.122414] EXT4-fs (mtdblock8): re-mounted. Opts: (null)
<6>[ 86.246748] EXT4-fs (mtdblock8): re-mounted. Opts: (null)
<6>[ 86.278212] EXT4-fs (mtdblock8): re-mounted. Opts: (null)
<6>[ 86.293196] EXT4-fs (mtdblock8): re-mounted. Opts: (null)
<6>[ 138.888253] binder: 996:1005 refcount change on invalid ref 20
<6>[ 141.867881] binder: 996:1976 refcount change on invalid ref 20
<6>[ 141.867999] binder: 996:1976 refcount change on invalid ref 20
<3>[ 141.868081] binder: transaction release 39126 bad handle 20
<6>[ 142.600188] binder: 996:1005 refcount change on invalid ref 34
<6>[ 142.660651] binder: 996:1976 refcount change on invalid ref 34
<6>[ 142.660727] binder: 996:1976 refcount change on invalid ref 34
<3>[ 142.660815] binder: transaction release 41115 bad handle 34
<6>[ 143.318846] binder: 996:1005 refcount change on invalid ref 49
<6>[ 143.392551] binder: 996:1976 refcount change on invalid ref 49
<6>[ 143.392621] binder: 996:1976 refcount change on invalid ref 49
<3>[ 143.392706] binder: transaction release 41474 bad handle 49
<6>[ 148.157154] binder: 996:1005 refcount change on invalid ref 52
<6>[ 148.168317] binder: 996:1976 refcount change on invalid ref 52
<6>[ 148.168420] binder: 996:1976 refcount change on invalid ref 52
<3>[ 148.168512] binder: transaction release 41590 bad handle 52
<6>[ 148.643682] binder: 996:1005 refcount change on invalid ref 56
<6>[ 148.723361] binder: 996:1976 refcount change on invalid ref 56
<6>[ 148.723432] binder: 996:1976 refcount change on invalid ref 56
<3>[ 148.723539] binder: transaction release 41842 bad handle 56
<6>[ 149.471020] binder: 996:1005 refcount change on invalid ref 61
<6>[ 149.549887] binder: 996:1976 refcount change on invalid ref 61
<6>[ 149.549954] binder: 996:1976 refcount change on invalid ref 61
<3>[ 149.550049] binder: transaction release 41985 bad handle 61
<6>[ 150.021855] binder: 996:1005 refcount change on invalid ref 71
<6>[ 150.168615] binder: 996:1976 refcount change on invalid ref 71
<6>[ 150.168698] binder: 996:1976 refcount change on invalid ref 71
<3>[ 150.168798] binder: transaction release 42218 bad handle 71
<6>[ 150.702339] binder: 996:1005 refcount change on invalid ref 19
<6>[ 150.860922] binder: 996:1976 refcount change on invalid ref 19
<6>[ 150.860997] binder: 996:1976 refcount change on invalid ref 19
<3>[ 150.861079] binder: transaction release 42458 bad handle 19
<6>[ 150.988430] binder: 996:1005 refcount change on invalid ref 25
<6>[ 151.085705] binder: 996:1976 refcount change on invalid ref 25
<6>[ 151.085796] binder: 996:1976 refcount change on invalid ref 25
<3>[ 151.085880] binder: transaction release 42645 bad handle 25
<6>[ 151.270773] binder: 996:1005 refcount change on invalid ref 32
<6>[ 151.292002] binder: 996:1976 refcount change on invalid ref 32
<6>[ 151.292104] binder: 996:1976 refcount change on invalid ref 32
<3>[ 151.292193] binder: transaction release 42764 bad handle 32
<6>[ 152.081414] binder: 996:1005 refcount change on invalid ref 48
<6>[ 152.085394] binder: 996:1976 refcount change on invalid ref 48
<6>[ 152.085454] binder: 996:1976 refcount change on invalid ref 48
<3>[ 152.085525] binder: transaction release 43122 bad handle 48
<6>[ 152.595570] binder: 996:1005 refcount change on invalid ref 51
<6>[ 152.689596] binder: 996:1976 refcount change on invalid ref 51
<6>[ 152.689679] binder: 996:1976 refcount change on invalid ref 51
<3>[ 152.689782] binder: transaction release 43373 bad handle 51
<6>[ 152.885724] binder: 996:1005 refcount change on invalid ref 61
<6>[ 152.972118] binder: 996:1976 refcount change on invalid ref 61
<6>[ 152.972187] binder: 996:1976 refcount change on invalid ref 61
<3>[ 152.972272] binder: transaction release 43514 bad handle 61
<6>[ 153.152154] binder: 996:1005 refcount change on invalid ref 66
<6>[ 153.159417] binder: 996:1976 refcount change on invalid ref 66
<6>[ 153.160579] binder: 996:1976 refcount change on invalid ref 66
<3>[ 153.160644] binder: transaction release 43630 bad handle 66
<4>[ 161.744214] standby rt5631
[email protected]:/ #
screenshot of About tab
I'm attaching screenshot of About tab
full dmesg
Last dmesg was cut from cmd.exe history buffer.
Here is full the dmesg
current best Rom
I just bought a xtreme x81 tab, and i would like to know what is the current best ROM.
I have installed the kitkat v2.4, and Antutu scores are lower than stock, and system sometimes freezes.
Many thanks in advance.
Hi oma.
in the woxter nimbus 98q does not work the wiffi and rotation in CM11, omnirom and lollipop. Can you help.
Thank you.
dmesg: https://mega.co.nz/#!fBA23TrK!VKQ9VEBYJP2ZZNunXSuv0nbyHUk5xRYXWcmbwuP sUT4
Request Rom for Qilive 9.7r
Goodmorning.
I am searching for a working Rom, stable as possible, for my Qilive 9.7r. 6 months ago you suggested this rom:
IRON by CrewRKTablets KK 4.4.2 v1.1 (from your website)
Can i use it or there is something new that can i use??
Thx a lots for your work!!!
chuwi v88s rom
hi,
im new in this procedure. I have bought the chuwi v88s tablet and it seems to stuck a lot. it really does.
I want to try a new rom and i want to ask if the procure u give in the video is still ok or have any updated ones i should follow.
Thanx a lot for your time
Rockchip Developers Please Help ME
I Have a Rockchip Tablet PCB V8_RK618_MV3.0_20130910
it named Gamma GA-TAB MINI
Screen : 7.9 inch
Internal : 16 GB
RAM : 2GB
Proccessor Type : RK3188-T
Processor Freq. : 1.6 Ghz Quad-Core
Touch IC : CT362
other info in the pics
the official site have no firmware download links.
i need a stock or custom firmware please i missed and flashed a boot.img with the recovery.img so the tablet now black screened
i have tried about 3 firmwares with no luck
Can Any One Help Me Please?
.:::Thanks:::.
Odys Ieos Quad
BT and Wifi still broken for the Ieos Quad?
Any way to fix that?
Does anyone know if Oma rom works for other Rockchip 3188 devices besides Chuwi v88? I have a fnf iFive x2 tablet with the same Rockchip chipset and quad core and want to install the "multi window edition" on it. If so, which version should I use? Thank you in advance for any help here!
bogarty said:
Does anyone know if Oma rom works for other Rockchip 3188 devices besides Chuwi v88? I have a fnf iFive x2 tablet with the same Rockchip chipset and quad core and want to install the "multi window edition" on it. If so, which version should I use? Thank you in advance for any help here!
Click to expand...
Click to collapse
It happened to me too. You forgot to choose your tablet kernel instead oma's kernel. Download it from kernel archive and try again. @Oma7144 I installed your OmniRom 1.4.1 in my pipo s1pro and it works very well, but i have some problems.
Rotation is not working, is there any fix?
HDMI is working only when i touch the screen and not at 1080p. If i play a movie i get a green screen.
Camera is rotated 90 degrees, but working.
I hope you can help me. Do you need a log? Thanks a lot.
djkail said:
It happened to me too. You forgot to choose your tablet kernel instead oma's kernel. Download it from kernel archive and try again. @Oma7144 I installed your OmniRom 1.4.1 in my pipo s1pro and it works very well, but i have some problems.
Rotation is not working, is there any fix?
HDMI is working only when i touch the screen and not at 1080p. If i play a movie i get a green screen.
Camera is rotated 90 degrees, but working.
I hope you can help me. Do you need a log? Thanks a lot.
Click to expand...
Click to collapse
I tried this fix for my S1Pro, and it worked a bit.
"CrewRKTablets KK Omni V1.4.1 Model Fix Pipo S3pro"
http://crewrktablets.arctablet.com/?wpfb_dl=2263
HDMI is now working perfectly!!
Rotation started to work, but its 90º turned to the right
Frontal camera is ok, but rear camera is 180º rotated
USB OTG is working too.
I hope you can help me. Thanks a lot.
Oma roms on Pipo M9 Max with 1x16Gb Nand flash
Can I use Oma rom on my Modecom freetab 1014 ips x4+ (PIPO M9 Max) ?
These roms are for Chuwi V88 with 2x 8Gb Nand chips. My tablet has only one chip. 1x16Gb (29f128g08cfaba)
Ok, I got an obscure Allwinner A31S based tablet by a company called "Tristan Auran" with model name Planet 3 from ebay for a few bucks. It's fairly nice for the price, and like with all the devices I get, I went about rooting and tuning it. While attempting to install a custom recovery, the recovery must have damaged something and the tablet refused to boot after starting it once.
I had a dump of the important partitions, but I couldn't read them back anymore and no matter how often I tried making a PhoenixSuite flashable image, they tablet would always lock up on the boot logo. Noone online seems to have a working stock rom, and the manufacturer didn't reply to my requests.
Seeing it as a lost cause, I downloaded firmware randomly of tablets that had the same or similar hardware configurations. I ended up finding one that actually booted fairly flawlessly and got most of everything working by editing the Allwinner SystemConfig and Build.prop to the right values. Touch, sound, graphics, all seems to work without major bugs.
The only thing that eludes me is Wlan at the moment. No matter what I tried it will not work on its own.
Interestingly, Wlan starts working when I boot with a plugged in USB Wlan stick. Not too surprising, but the onboard Wlan chip ALSO starts working when I unplug the USB Stick and insmod the proper driver quickly (the USB stick uses an RTL8188 chip, and the onboard chip is a RTL8723AS combined wlan/bluetooth chip).
Reading the logs has been a bit enigmatic to me, and all I could glean is that for some reason the drivers unload when the USB stick is NOT plugged in, but not why or how I could fix that.
When I boot without plugged in USB stick, the onboard wlan is not appearing on an lsusb printout, if I boot with it plugged in they BOTH appear with their proper IDs.
Any help is appreciated, and if you happen to have the same tablet I'll upload the image somwhere.
Here is a dmesg printout of the section with the 8188 driver loading with the USB stick NOT plugged in for starters.
I'm sure that there is some other weirdness in there, but everything else seems to work well, so I wouldn't worry too much about anything unrelated to wlan or USB.
Code:
<6>[ 36.404154] hub 4-0:1.0: USB hub found
<6>[ 36.404204] hub 4-0:1.0: 1 port detected
<7>[ 36.406089] SELinux: initialized (dev mmcblk0p1, type vfat), uses genfs_contexts
<6>[ 36.407880] usbcore: registered new interface driver rtl8188eu
<4>[ 36.407896] RTL871X: module init ret=0
<3>[ 36.411642] init: no such service 'fuse_extsd'
<6>[ 36.751853] usb 4-1: new full-speed USB device number 2 using sw-ohci
<6>[ 36.924743] usb 4-1: not running at top speed; connect to a high speed hub
<6>[ 36.942782] rtk_btusb: btusb_probe 1==========can_wakeup=1 flag2=0
<6>[ 36.942798] rtk_btusb: patch_add
<6>[ 36.942828] rtk_btusb: hci_register_dev e3e6e800 name bus 1
<6>[ 36.942840] rtk_btusb: id=0
<6>[ 36.942851] rtk_btusb: hdev->name=hci0
<3>[ 36.942859] rtk_btusb: ===================hci_register_dev success
<4>[ 38.123389] [ND]flush cache 1 1!
<7>[ 38.144630] SELinux: initialized (dev nandk, type vfat), uses genfs_contexts
<3>[ 38.147101] init: no such service 'fuse_sdcard'
<6>[ 38.958934] init: waitpid returned pid 2790, status = 00000000
<3>[ 38.958969] init: untracked pid 2790 exited
<4>[ 40.843108] RTL871X: module exit start
<6>[ 40.843133] usbcore: deregistering interface driver rtl8188eu
<4>[ 40.843927] [sw_hci_sun6i]: ERR: sw_ehci is null
<4>[ 40.843946] [sw_hci_sun6i]: [sw-ohci1]: sw_usb_disable_ohci
<4>[ 40.843965] [sw_hci_sun6i]: [sw-ohci1]: remove, pdev->name: sw-ohci, pdev->id: 1, sw_ohci: 0xc08e5fb4
<6>[ 40.843992] sw-ohci sw-ohci.1: remove, state 1
<6>[ 40.844029] usb usb4: USB disconnect, device number 1
<6>[ 40.844049] usb 4-1: USB disconnect, device number 2
<6>[ 40.844388] rtk_btusb: btusb_disconnect
<6>[ 40.844401] rtk_btusb: patch_remove
<6>[ 40.844419] rtk_btusb: hci_unregister_dev hdeve3e6e800 name hci0 bus 1
<6>[ 40.844437] rtk_btusb: btusb_flush add delay
<6>[ 40.866089] sw-ohci sw-ohci.1: USB bus 4 deregistered
<4>[ 40.866129] [sw_hci_sun6i]: [sw-ohci1]: Set USB Power OFF
<4>[ 40.866148] [sw_hci_sun6i]: [sw-ohci1]: close clock
<4>[ 40.866178] [RTL8723AS]: Set GPIO rtk_rtl8723as_wl_dis to 0 !
<4>[ 40.866192] [RTL8723AS]: RTL8723AS is powered down by wifi
<4>[ 40.866204] [RTL8723AS]: rtl8723as module power set by axp.
and WITH the USB stick.
Code:
<6>[ 35.781577] hub 4-0:1.0: USB hub found
<6>[ 35.781645] hub 4-0:1.0: 1 port detected
<7>[ 35.785044] SELinux: initialized (dev mmcblk0p1, type vfat), uses genfs_contexts
<3>[ 35.790935] init: no such service 'fuse_extsd'
<4>[ 35.794361] bFWReady == _FALSE call reset 8051...
<4>[ 35.823665] RTL871X: rtw_ndev_init(wlan0)
<4>[ 35.867817] RTL871X: rtw_ndev_init(p2p0)
<6>[ 35.879110] usbcore: registered new interface driver rtl8188eu
<4>[ 35.879129] RTL871X: module init ret=0
<6>[ 36.078727] init: computing context for service '/system/bin/logwrapper'
<5>[ 36.079073] init: starting 'p2p_supplicant'
<6>[ 36.080865] init: Created socket '/dev/socket/wpa_wlan0' with mode '660', user '1010', group '1010'
<6>[ 36.121142] usb 4-1: new full-speed USB device number 2 using sw-ohci
<6>[ 36.294094] usb 4-1: not running at top speed; connect to a high speed hub
<6>[ 36.320360] rtk_btusb: btusb_probe 1==========can_wakeup=1 flag2=0
<6>[ 36.320382] rtk_btusb: patch_add
<6>[ 36.320455] rtk_btusb: hci_register_dev e43cf800 name bus 1
<6>[ 36.320473] rtk_btusb: id=0
<6>[ 36.320498] rtk_btusb: hdev->name=hci0
<3>[ 36.320523] rtk_btusb: ===================hci_register_dev success
<4>[ 36.581279] ==> rtl8188e_iol_efuse_patch
<6>[ 36.848256] ADDRCONF(NETDEV_UP): p2p0: link is not ready
<6>[ 37.145264] ADDRCONF(NETDEV_UP): wlan0: link is not ready
<4>[ 37.569824] [ND]flush cache 1 1!
<7>[ 37.572658] SELinux: initialized (dev nandk, type vfat), uses genfs_contexts
<3>[ 37.574856] init: no such service 'fuse_sdcard'
<6>[ 38.318666] init: waitpid returned pid 2873, status = 00000000
<3>[ 38.318707] init: untracked pid 2873 exited
<4>[ 38.616284] RTL871X: rtw_set_802_11_connect(wlan0) fw_state=0x00000008
<4>[ 38.701415] RTL871X: start auth
<4>[ 38.705556] RTL871X: auth success, start assoc
<4>[ 38.709440] RTL871X: assoc success
<6>[ 38.709987] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
This happens after I disconnect the USB stick and insmod the 8723au.ko driver. (Although I'm confused by the mess of chip model names. Might not actually be the 8723au driver that talks to the onboard chip. as I said, can't make a sese of it.)
Code:
<4>[ 113.662806] [sun6i_usb]: ERR: sw_hcd_host_rx, end 2 RX proto error(0x204)
<4>[ 113.662841] [sun6i_usb]: ERR: sw_hcd_host_rx, end 2 RX proto error(0x4)
<4>[ 113.662885] [sun6i_usb]:
<4>[ 113.662889] ------------IRQ DISCONNECT-------------
<4>[ 113.662894]
<6>[ 113.662966] usb 3-1: USB disconnect, device number 2
<4>[ 113.710835] [sun6i_usb]: [sw_hcd]: sw_hcd_urb_dequeue, sw_hcd(e622b4d8, 0x0, 0x3f),urb(e3475140, 4000, 0), dev = 2, ep = 1, dir = in
<4>[ 113.710859] [sun6i_usb]: sw_hcd_cleanup_urb: qh(0xe0357e40,0x1,0x2), urb(0xe3475140,4000,0), ep(0xe622b5cc,2,0xe0357e40,0x (null))
<4>[ 113.710876] [sun6i_usb]: ERR: sw_hcd_advance_schedule, host is not active
<4>[ 113.710894] [sun6i_usb]: [sw_hcd]: sw_hcd_urb_dequeue, sw_hcd(e622b4d8, 0x0, 0x3f),urb(e34750c0, 4000, 0), dev = 2, ep = 1, dir = in
<4>[ 113.710915] [sun6i_usb]: sw_hcd_cleanup_urb: qh(0xe0357e40,0x1,0x2), urb(0xe34750c0,4000,0), ep(0xe622b5cc,2,0xe0357e40,0x (null))
<4>[ 113.710931] [sun6i_usb]: ERR: sw_hcd_advance_schedule, host is not active
<4>[ 113.710948] [sun6i_usb]: [sw_hcd]: sw_hcd_urb_dequeue, sw_hcd(e622b4d8, 0x0, 0x3f),urb(e3f09f40, 4000, 0), dev = 2, ep = 1, dir = in
<4>[ 113.710969] [sun6i_usb]: sw_hcd_cleanup_urb: qh(0xe0357e40,0x1,0x2), urb(0xe3f09f40,4000,0), ep(0xe622b5cc,2,0xe0357e40,0x (null))
<4>[ 113.710984] [sun6i_usb]: ERR: sw_hcd_advance_schedule, host is not active
<4>[ 113.711001] [sun6i_usb]: [sw_hcd]: sw_hcd_urb_dequeue, sw_hcd(e622b4d8, 0x0, 0x3f),urb(e3f09ec0, 4000, 0), dev = 2, ep = 1, dir = in
<4>[ 113.711021] [sun6i_usb]: sw_hcd_cleanup_urb: qh(0xe0357e40,0x1,0x2), urb(0xe3f09ec0,4000,0), ep(0xe622b5cc,2,0xe0357e40,0x (null))
<4>[ 113.711037] [sun6i_usb]: ERR: sw_hcd_advance_schedule, host is not active
<4>[ 113.711054] [sun6i_usb]: [sw_hcd]: sw_hcd_urb_dequeue, sw_hcd(e622b4d8, 0x0, 0x3f),urb(e3f09e40, 4000, 0), dev = 2, ep = 1, dir = in
<4>[ 113.711075] [sun6i_usb]: sw_hcd_cleanup_urb: qh(0xe0357e40,0x1,0x2), urb(0xe3f09e40,4000,0), ep(0xe622b5cc,2,0xe0357e40,0x (null))
<4>[ 113.711090] [sun6i_usb]: ERR: sw_hcd_advance_schedule, host is not active
<4>[ 113.711107] [sun6i_usb]: [sw_hcd]: sw_hcd_urb_dequeue, sw_hcd(e622b4d8, 0x0, 0x3f),urb(e34752c0, 4000, 0), dev = 2, ep = 1, dir = in
<4>[ 113.711128] [sun6i_usb]: sw_hcd_cleanup_urb: qh(0xe0357e40,0x1,0x2), urb(0xe34752c0,4000,0), ep(0xe622b5cc,2,0xe0357e40,0x (null))
<4>[ 113.711143] [sun6i_usb]: ERR: sw_hcd_advance_schedule, host is not active
<4>[ 113.711160] [sun6i_usb]: [sw_hcd]: sw_hcd_urb_dequeue, sw_hcd(e622b4d8, 0x0, 0x3f),urb(e3475240, 4000, 0), dev = 2, ep = 1, dir = in
<4>[ 113.711181] [sun6i_usb]: sw_hcd_cleanup_urb: qh(0xe0357e40,0x1,0x2), urb(0xe3475240,4000,0), ep(0xe622b5cc,2,0xe0357e40,0x (null))
<4>[ 113.711196] [sun6i_usb]: ERR: sw_hcd_advance_schedule, host is not active
<4>[ 113.711213] [sun6i_usb]: [sw_hcd]: sw_hcd_urb_dequeue, sw_hcd(e622b4d8, 0x0, 0x3f),urb(e34751c0, 4000, 0), dev = 2, ep = 1, dir = in
<4>[ 113.711233] [sun6i_usb]: sw_hcd_cleanup_urb: qh(0xe0357e40,0x1,0x2), urb(0xe34751c0,4000,0), ep(0xe622b5cc,2,0xe0357e40,0x (null))
<4>[ 113.711249] [sun6i_usb]: ERR: sw_hcd_advance_schedule, host is not active
<4>[ 113.711369] RTL871X: rtw_cmd_thread: DriverStopped(1) SurpriseRemoved(1) break at line 478
<6>[ 113.732930] cfg80211: Calling CRDA for country: DE
<4>[ 113.771502] RTL871X: rtw_ndev_uninit(wlan0)
<5>[ 113.835924] init: service 'dhcpcd_wlan0' is being killed
<6>[ 113.836827] init: waitpid returned pid 3172, status = 00000009
<5>[ 113.836855] init: process 'dhcpcd_wlan0', pid 3172 exited
<4>[ 113.930931] [sun6i_usb]:
<4>[ 113.930936]
<4>[ 113.930939] rmmod_host_driver
<4>[ 113.930943]
<4>[ 113.930957] [sw_hcd0]: sw_usb_host0_disable start
<4>[ 113.930970] [sw_hcd0]: sw_hcd_wait_for_disconnect cnt=0
<4>[ 113.930984] [sun6i_usb]: [sw_hcd_host0]: Set USB Power OFF
<4>[ 113.931172] [sun6i_usb]: -------sw_hcd0_soft_disconnect---------
<4>[ 113.931207] [sun6i_usb]: wrn: hcd is not enable, need not stop hcd
<4>[ 113.931245] [sw_hcd0]: close_usb_clock
<4>[ 113.931267] [sw_hcd0]: sw_usb_host0_disable end
<4>[ 113.991092] RTL871X: rtw_ndev_uninit(p2p0)
<6>[ 114.057791] healthd: battery l=100 v=4156 t=30.0 h=2 st=5 c=3 chg=au
<4>[ 114.211428] RTL871X: rtw_dev_unload: driver not in IPS
<4>[ 114.212611] [sun6i_usb]: [sw_hcd]: sw_hcd_h_disable, epnum = 0
<4>[ 114.212625] [sun6i_usb]: [sw_hcd]: sw_hcd_h_disable, epnum = 0
<4>[ 114.212636] [sun6i_usb]: [sw_hcd]: sw_hcd_h_disable, epnum = 81
<4>[ 114.212648] [sun6i_usb]: [sw_hcd]: sw_hcd_h_disable, epnum = 2
<4>[ 114.212658] [sun6i_usb]: [sw_hcd]: sw_hcd_h_disable, epnum = 3
<6>[ 114.232911] healthd: battery l=100 v=4156 t=30.0 h=2 st=5 c=3 chg=a
<4>[ 128.464964] [RTL8723AS]: Set GPIO rtk_rtl8723as_wl_dis to 1 !
<4>[ 128.464985] [RTL8723AS]: RTL8723AS is powered up by wifi
<4>[ 128.464997] [RTL8723AS]: rtl8723as module power set by axp.
<4>[ 128.465116] create_regulator: axp22_ldo5: Failed to create debugfs directory
<4>[ 128.465638] [RTL8723AS]: RTL8723AS power state change: wifi 1, bt 0 !!
<4>[ 128.465663] [RTL8723AS]: succeed to set gpio rtk_rtl8723as_wl_dis to 1 !
<4>[ 128.465677] [RTL8723AS]: sdio wifi power state: on
<6>[ 130.511390] usbcore: registered new interface driver rtl8723au
<6>[ 134.264995] ADDRCONF(NETDEV_UP): wlan0: link is not ready
<4>[ 136.498820] RTL871X: rtw_set_802_11_connect(wlan0) fw_state=0x00000008
<4>[ 136.680901] RTL871X: start auth
<4>[ 136.683811] RTL871X: auth success, start assoc
<4>[ 136.688876] RTL871X: assoc success
<6>[ 136.689288] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
<4>[ 136.711963] RTL871X: send eapol packet
<4>[ 136.722834] UpdateHalRAMask8192CUsb => mac_id:0, networkType:0x0b, mask:0x000fffff
<4>[ 136.722843] ==> rssi_level:0, rate_bitmap:0x000ff005
<4>[ 136.725356] RTL871X: send eapol packet
<4>[ 136.857833] RTL871X: set pairwise key to hw: alg:4(WEP40-1 WEP104-5 TKIP-2 AES-4) camid:4
<4>[ 136.881808] RTL871X: set group key to hw: alg:4(WEP40-1 WEP104-5 TKIP-2 AES-4) keyid:1
<6>[ 136.938034] init: computing context for service '/system/bin/dhcpcd'
<5>[ 136.938412] init: starting 'dhcpcd_wlan0'
<4>[ 138.349822] UpdateHalRAMask8192CUsb => mac_id:0, networkType:0x0b, mask:0x000fffff
<4>[ 138.349831] ==> rssi_level:2, rate_bitmap:0x000ff000
<6>[ 158.933711] cfg80211: Calling CRDA to update world regulatory domain
<4>[ 161.069767] RTL871X: rtw_set_802_11_connect(wlan0) fw_state=0x00000008
<4>[ 161.254903] RTL871X: start auth
<4>[ 161.257812] RTL871X: auth success, start assoc
<4>[ 161.261880] RTL871X: assoc success
<6>[ 161.262289] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
<4>[ 161.294824] UpdateHalRAMask8192CUsb => mac_id:0, networkType:0x0b, mask:0x000fffff
<4>[ 161.294833] ==> rssi_level:0, rate_bitmap:0x000ff005
<4>[ 162.347821] UpdateHalRAMask8192CUsb => mac_id:0, networkType:0x0b, mask:0x000fffff
<4>[ 162.347829] ==> rssi_level:2, rate_bitmap:0x000ff000
<5>[ 167.150502] init: service 'dhcpcd_wlan0' is being killed
<6>[ 167.151527] init: waitpid returned pid 5785, status = 00000009
<5>[ 167.151552] init: process 'dhcpcd_wlan0', pid 5785 exited
<6>[ 167.151652] init: waitpid returned pid 5988, status = 00000009
<3>[ 167.151676] init: untracked pid 5988 exited
<6>[ 167.488584] cfg80211: Calling CRDA to update world regulatory domain
<4>[ 169.619684] RTL871X: rtw_set_802_11_connect(wlan0) fw_state=0x00000008
<4>[ 169.754869] RTL871X: start auth
<4>[ 169.756810] RTL871X: auth success, start assoc
<4>[ 169.760866] RTL871X: assoc success
<4>[ 169.793814] UpdateHalRAMask8192CUsb => mac_id:0, networkType:0x0b, mask:0x000fffff
<4>[ 169.793822] ==> rssi_level:0, rate_bitmap:0x000ff005
<6>[ 169.974281] init: computing context for service '/system/bin/dhcpcd'
<5>[ 169.974537] init: starting 'dhcpcd_wlan0'
<4>[ 170.347837] UpdateHalRAMask8192CUsb => mac_id:0, networkType:0x0b, mask:0x000fffff
<4>[ 170.347845] ==> rssi_level:2, rate_bitmap:0x000ff000
<6>[ 176.033973] cfg80211: Calling CRDA for country: DE
<5>[ 176.042455] init: service 'dhcpcd_wlan0' is being killed
<6>[ 176.043355] init: waitpid returned pid 6052, status = 00000009
<5>[ 176.043381] init: process 'dhcpcd_wlan0', pid 6052 exited
<4>[ 176.752841] RTL871X: rtw_set_802_11_connect(wlan0) fw_state=0x00000008
<4>[ 176.920935] RTL871X: start auth
<4>[ 176.923854] RTL871X: auth success, start assoc
<4>[ 176.928948] RTL871X: assoc success
<6>[ 176.929450] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
<4>[ 176.952660] RTL871X: send eapol packet
<4>[ 176.961837] UpdateHalRAMask8192CUsb => mac_id:0, networkType:0x0b, mask:0x000fffff
<4>[ 176.961846] ==> rssi_level:0, rate_bitmap:0x000ff005
<4>[ 176.963241] RTL871X: send eapol packet
<4>[ 177.095848] RTL871X: set pairwise key to hw: alg:4(WEP40-1 WEP104-5 TKIP-2 AES-4) camid:4
<4>[ 177.119838] RTL871X: set group key to hw: alg:4(WEP40-1 WEP104-5 TKIP-2 AES-4) keyid:1
<6>[ 177.189899] init: computing context for service '/system/bin/dhcpcd'
<5>[ 177.190155] init: starting 'dhcpcd_wlan0'
<4>[ 178.347825] UpdateHalRAMask8192CUsb => mac_id:0, networkType:0x0b, mask:0x000fffff
<4>[ 178.347833] ==> rssi_level:2, rate_bitmap:0x000ff000
<6>[ 199.844666] cfg80211: Calling CRDA to update world regulatory domain
<4>[ 201.990451] RTL871X: rtw_set_802_11_connect(wlan0) fw_state=0x00000008
<4>[ 202.216893] RTL871X: start auth
<4>[ 202.219807] RTL871X: auth success, start assoc
<4>[ 202.223864] RTL871X: assoc success
<4>[ 202.256829] UpdateHalRAMask8192CUsb => mac_id:0, networkType:0x0b, mask:0x000fffff
<4>[ 202.256839] ==> rssi_level:0, rate_bitmap:0x000ff005
<4>[ 202.492815] UpdateHalRAMask8192CUsb => mac_id:0, networkType:0x0b, mask:0x000fffff
<4>[ 202.492822] ==> rssi_level:2, rate_bitmap:0x000ff000
<6>[ 207.262315] init: waitpid returned pid 6228, status = 00000100
<5>[ 207.262345] init: process 'dhcpcd_wlan0', pid 6228 exited
<6>[ 207.293697] cfg80211: Calling CRDA for country: DE
<4>[ 210.510748] RTL871X: nolinked power save enter
<4>[ 216.489797] RTL871X: nolinked power save leave
<4>[ 220.480740] RTL871X: nolinked power save enter
<6>[ 221.232645] healthd: battery l=100 v=4144 t=30.0 h=2 st=5 c=3 chg=a
<4>[ 224.291801] RTL871X: nolinked power save leave
<4>[ 224.295810] RTL871X: rtw_set_802_11_connect(wlan0) fw_state=0x00000008
<4>[ 224.435912] RTL871X: start auth
<4>[ 224.438824] RTL871X: auth success, start assoc
<4>[ 226.734820] RTL871X: rtw_set_802_11_connect(wlan0) fw_state=0x00000008
<4>[ 226.894886] RTL871X: start auth
<4>[ 226.897805] RTL871X: auth success, start assoc
<4>[ 226.902877] RTL871X: assoc success
<4>[ 226.927654] RTL871X: send eapol packet
<4>[ 226.936846] UpdateHalRAMask8192CUsb => mac_id:0, networkType:0x0b, mask:0x000fffff
<4>[ 226.936855] ==> rssi_level:0, rate_bitmap:0x000ff005
<4>[ 226.938306] RTL871X: send eapol packet
<4>[ 227.072854] RTL871X: set pairwise key to hw: alg:4(WEP40-1 WEP104-5 TKIP-2 AES-4) camid:4
<4>[ 227.096820] RTL871X: set group key to hw: alg:4(WEP40-1 WEP104-5 TKIP-2 AES-4) keyid:1
<6>[ 227.152065] init: computing context for service '/system/bin/dhcpcd'
<5>[ 227.152336] init: starting 'dhcpcd_wlan0'
<4>[ 229.403830] UpdateHalRAMask8192CUsb => mac_id:0, networkType:0x0b, mask:0x000fffff