Hi.
Just tryed to inst. Android in my HD2 and now it stuck with a white screen with the HTC logo.
Is it any way to fix this or do i just trach it?
I am not an expert but this happened to me once while installing SD android.
I reinstalled the original ROM from the HTC site and restored my phone to factory settings.
I tried another version of android and it worked well (since last September).
Only observation is that lately (last two month) my phone hangs a lot on both systems (droid & win) and overheats a lot and when this happens I need to wait for it to cool down (at least 20 minutes) then it accepts rebooting (I am stating this although I am not sure is it from the droid or just my HW is faulty for other reasons).
I hope this helps
I tryed a NAND install. Now I cant get conection with usb and computer
Maybe you can perform a hard reset with buttons
1. With the phone turned off, press and hold the VOLUME UP and VOLUME DOWN buttons, then press the END/POWER button shortly and release it.
2. Release the VOLUME UP and VOLUME DOWN buttons.
3. Press the VOLUME UP button to perform the hard reset, or press any other button to cancel the reset.
I hope it works
3mo said:
Maybe you can perform a hard reset with buttons
1. With the phone turned off, press and hold the VOLUME UP and VOLUME DOWN buttons, then press the END/POWER button shortly and release it.
2. Release the VOLUME UP and VOLUME DOWN buttons.
3. Press the VOLUME UP button to perform the hard reset, or press any other button to cancel the reset.
I hope it works
Click to expand...
Click to collapse
didnt work hehe still at the white htc logo screen. I migth installed the files the wrong way round?
Can you get to bootloader (3 coloured screen) by turning on the phone whilst holding vol down?
conantroutman said:
Can you get to bootloader (3 coloured screen) by turning on the phone whilst holding vol down?
Click to expand...
Click to collapse
Yes that's about the only thing i can do
Go-Fast said:
Yes that's about the only thing i can do
Click to expand...
Click to collapse
As long as you can get to bootloader its ok
I would start over from the begining.....
Does it still show that you have HSPL installed on bootloader?
If so, reflash the windows 6.5 ROM that you were using before the android flash.
Then follow the steps in this thread.
Hope that helps....
conantroutman said:
As long as you can get to bootloader its ok
I would start over from the begining.....
Does it still show that you have HSPL installed on bootloader?
If so, reflash the windows 6.5 ROM that you were using before the android flash.
Then follow the steps in this thread.
Hope that helps....
Click to expand...
Click to collapse
Thnx I'll try it later and report back
Still cant get my coputer to connect to the phone.
I get to the "red green and blue" screen, and it says
PB01100 HX-BC
SPL-2.00.HSPL 8G XE
0x85
CotullaHSPL 0x40
I'm on win7 SP1
Ok when you enter bootloader (red green blue screen) you should see "Serial" at the bottom..
When you connect to the computer it should change to "USB"
You might not see anything happen on your computer but the word at the bottom of the bootloader should change.
I might be mistaken here but Im pretty sure you need "2.08 HSPL" although your bootloader shows you have HSPL installed its not 2.08. This might be the cause of your original problem.
Once it says "USB" your ready to flash a ROM via USB as usual...
If it stays on "Serial" after a few minutes then try another USB port or computer if possible.
Enter bootloader and run the HSPL tool and choose 2.08HSPL......
Then start the process from the beggining.
Hope that helps.
conantroutman said:
Ok when you enter bootloader (red green blue screen) you should see "Serial" at the bottom..
When you connect to the computer it should change to "USB"
You might not see anything happen on your computer but the word at the bottom of the bootloader should change.
I might be mistaken here but Im pretty sure you need "2.08 HSPL" although your bootloader shows you have HSPL installed its not 2.08. This might be the cause of your original problem.
Once it says "USB" your ready to flash a ROM via USB as usual...
If it stays on "Serial" after a few minutes then try another USB port or computer if possible.
Enter bootloader and run the HSPL tool and choose 2.08HSPL......
Then start the process from the beggining.
Hope that helps.
Click to expand...
Click to collapse
Hah your a babe conantroutman lol thnx
Is this the rigth SPL ?
Not to intrude on conantroutman here but yes you have to have HSPL 2.08 and a 2.15.50.14 or 2.10.50.02 radio for MAGLDR to work. Without the HSPL 2.08 you can not flash MAGLDR and without the proper radio version MAGLDR will not even boot up.
So to answer your question yes the HSPL you have in the picture you posted is the correct HSPL.
Yep as T said, hspl is good, radio is good. Your all set.
That guide for installing android at the top of the thread is pretty damn good and will have you up and running in no time. Let us know how you get on
Sent From My Fingers To Your Face.....
thnx to both of you. I'll post here when done
Crap my call button dont work when I'm in bootloader
When your in the MAGLDR menu?
You may have to flash WM again to test the call button. Or try reflashing MAGLDR, that may help...
Sent From My Fingers To Your Face.....
I guesse it's a lost case so I just installed winmo and runing android from SD card
thnx for the help.
btw!
is there a way to get htc sense to work on a huawei u8800 or x5?
Hmmm its very weird because if your call button works in WM then it should work in MAGLDR....
Related
hey guys,, I did a foolish thing and now i'm stuck!!!
I did the HardSPL thing(apparently wrong!!)
and then i started using RUU flashig the new rom
so now from my SPL on the boot screen i get that the hardSPL didn’t function, and its stuck in boot loader with old SPL
and now that i've flashed the new rom, i cant hardSPL again,,,,
I'm so stuck,
i guess i can flash AKU 2.2 and then hardSPL again,
does it gonna work?
is there anyyyything i can do?
plzzzzzzz
IPL 2.20.0001
SPL 2.20.0001
thom_yorke said:
hey guys,, I did a foolish thing and now i'm stuck!!!
I did the HardSPL thing(apparently wrong!!)
and then i started using RUU flashig the new rom
so now from my SPL on the boot screen i get that the hardSPL didn’t function, and its stuck in boot loader with old SPL
and now that i've flashed the new rom, i cant hardSPL again,,,,
I'm so stuck,
i guess i can flash AKU 2.2 and then hardSPL again,
does it gonna work?
is there anyyyything i can do?
plzzzzzzz
IPL 2.20.0001
SPL 2.20.0001
Click to expand...
Click to collapse
try the ................................
ok, let me know about this ( i've found at WIKI )
Prophet Hard Reset Procedures
How to make a PROPER Hard Reset?
Method 1:
1. Press Camm & Comm button simultaniously. Keep them pressed.
2. Punch the little hole at the bottom with the stylus for a second or two.
3. Release the stylus (keep the buttons pressed!)
4. A white text-message appears on a black screen, telling you to press the send button
5. press the green button(the one you press to make a call).
6. Now, release the Camm & Comm buttons
7. The message on the screen tells you some more about formatting.
8. Release every button, you are done!
Done.... I had done untill number 3.
But a strange at number 4 and 5 !
I stand push Cam and Comm button while pressing green button, but nothing happen !!
Did I do wrong thing ? When I release Cam and Comm THEN I press green button, there is a massage that format FAILED !!!
plz give me a hint for this one ...
cheers,
ermen
ermenzegna said:
ok, let me know about this ( i've found at WIKI )
Prophet Hard Reset Procedures
How to make a PROPER Hard Reset?
Method 1:
1. Press Camm & Comm button simultaniously. Keep them pressed.
2. Punch the little hole at the bottom with the stylus for a second or two.
3. Release the stylus (keep the buttons pressed!)
4. A white text-message appears on a black screen, telling you to press the send button
5. press the green button(the one you press to make a call).
6. Now, release the Camm & Comm buttons
7. The message on the screen tells you some more about formatting.
8. Release every button, you are done!
Done.... I had done untill number 3.
But a strange at number 4 and 5 !
I stand push Cam and Comm button while pressing green button, but nothing happen !!
Did I do wrong thing ? When I release Cam and Comm THEN I press green button, there is a massage that format FAILED !!!
plz give me a hint for this one ...
cheers,
ermen
Click to expand...
Click to collapse
4.1 release all buttons now,
( cancel step 6.)
OK???
dioxda2 said:
4.1 release all buttons now,
( cancel step 6.)
OK???
Click to expand...
Click to collapse
YES !!! I got message FAILED !.
ermenzegna said:
YES !!! I got message FAILED !.
Click to expand...
Click to collapse
what failed??????
1. insert stylus into the little hole (or press power button if your pda turned off) then release
2. immediately press both camera + comm buttons at the same time, wait..
3. on the black screen when you see that question (are u sure u want to format bla bla.. yes or no..), release your fingers.
4. press green button used for dialing..
i understand that you reached up to the format phase, but format is failed.
the image on your pda's rom is corrupted or it coudn't be successfully flashed, so i think you must flash again.
before trying to flash wm6.1, remember to hardSPL your device..
good luck!
thom_yorke said:
hey guys,, I did a foolish thing and now i'm stuck!!!
I did the HardSPL thing(apparently wrong!!)
and then i started using RUU flashig the new rom
so now from my SPL on the boot screen i get that the hardSPL didn’t function, and its stuck in boot loader with old SPL
and now that i've flashed the new rom, i cant hardSPL again,,,,
I'm so stuck,
i guess i can flash AKU 2.2 and then hardSPL again,
does it gonna work?
is there anyyyything i can do?
plzzzzzzz
IPL 2.20.0001
SPL 2.20.0001
Click to expand...
Click to collapse
There is this thing called the "wiki" that contains the answer to your problem. It's link includes the words "stuck in bootloader". Take a look, and you should be fine!
dioxda2 said:
try the Lazy_Tool................................... http://forum.xda-developers.com/showthread.php?t=353547
Click to expand...
Click to collapse
Your lazy tool needs an active sync connection! It's use here is wholly inappropriate.
l3v5y said:
Your lazy tool needs an active sync connection! It's use here is wholly inappropriate.
Click to expand...
Click to collapse
My intention is to help. Even not helpful, not harmful at all......
Sry for bad english, but here is my problem:
After I did the downgrade to stock ROM with SPL, the bootloader wouldn't accept any connection from the USB at all. When I install HSPL again, the phone goes into bootloader, but no USB is found in the bootloader. The USB disconnects from the computer, so the HSPL installation isn't really able to connect after being brought into bootloader. The same happends when I try a stock ROM upgrade from HTC.
After the phones hits the bootloader, after a second or so, a new screen comes up. It says "Loading..." and it just stays there, no contact. Doing a reboot with the small red button works, and brings me back into booting up Windows.
Any idea on how I may install HSPL again?
anno65120 said:
After I did the downgrade to stock ROM with SPL, the bootloader wouldn't accept any connection from the USB at all. When I install HSPL again, the phone goes into bootloader, but no USB is found in the bootloader.
Click to expand...
Click to collapse
are you sure? does the word 'serial' not change to 'USB'?
ignore the pc, doesnt matter that the pc doesnt connect activesync.
The USB disconnects from the computer, so the HSPL installation isn't really able to connect after being brought into bootloader. The same happends when I try a stock ROM upgrade from HTC.
After the phones hits the bootloader, after a second or so, a new screen comes up. It says "Loading..." and it just stays there, no contact. Doing a reboot with the small red button works, and brings me back into booting up Windows.
Any idea on how I may install HSPL again?
Click to expand...
Click to collapse
dont forget that you cant just use ANY stock rom, it must be your phones original stock rom.
Go into bootloader, if 'serial' DOES change to 'USB' run hspl.exe (right click and run as administrator)
The white area doesn't show anything. No serial, no USB, nothing at all.
anno65120 said:
The white area doesn't show anything. No serial, no USB, nothing at all.
Click to expand...
Click to collapse
are you manually entering bootloader? if not, then try entering manually.
(Power off, press and hold vol down, tap and release power)
Is that any different?
When I use the method posted above, I get to the bootloader screen, and then to a white screen showing only "loading...". It¨s the same result as when I am trying to install HSPL, or an official ROM upgrade from HTC There's nothing in the white area of the tricolor bootloader screen, no serial or USB. If there had been something there, the case would have been solved easily, but it's nothing at all, The tricolor screen only shows for a split-second and then it goes further to the loading screen (the screen that shows only "loading").
It seems for me to be impossible to solve this
I've just had the same problem but managed to fix it tonight. I'm so happy, thought I'd bricked it.
1. Remove any SD card. Possibly you have a "LEOIMG.nbh" file on it that the bootloader is trying to load and getting stuck.
2. Now try manually loading the bootloader. (Disconnect the battery. Connect the battery. Hold volume down & press power.)
3. Hopefully you now have the bootloader on. Plug into the USB on the motherboard of your computer at the back.
4. You should see USB on bootloader. Run HSPL in admin mode (right click the HSPL.exe to run as admin).
Hopefully that works for you.
anno65120 said:
When I use the method posted above, I get to the bootloader screen, and then to a white screen showing only "loading...".
Click to expand...
Click to collapse
as red above said, , , you probably have an image on your sd card.
I am having the same problem as above. However, when I connect the USB to my PC, it doesn't change from "Serial" to "USB". I am unable to install HSPL. What do I do?
Zythyr said:
I am having the same problem as above. However, when I connect the USB to my PC, it doesn't change from "Serial" to "USB". I am unable to install HSPL. What do I do?
Click to expand...
Click to collapse
i am having the same problem. please help!!
kunsam said:
i am having the same problem. please help!!
Click to expand...
Click to collapse
And me too as well,,,still no luck after all the suggestions
PLease can anyone let me know the process to load a rom onto a HD2 that will not boot up....? Windows mobile device center will not detect it either. Bootlogger screen says I have SPL-2.08.HSPL 8G XE, and underneath it says CotullaHSPL if that is any help. I would really appreciate any help!
lisah456 said:
PLease can anyone let me know the process to load a rom onto a HD2 that will not boot up....? Windows mobile device center will not detect it either. Bootlogger screen says I have SPL-2.08.HSPL 8G XE, and underneath it says CotullaHSPL if that is any help. I would really appreciate any help!
Click to expand...
Click to collapse
After task 29 you have to flash a ROM. Task 29 wipes your device so if you don't hold down the volume down key at the end of task 29 it will not have any operating system. Just remove the battery and hold down the volume down key till you see the bootloader screen. Then flash your ROM and all is ok.
after task29,when your device reboot
press botton "volume down" and will go in bootloader mode
now if you have your device stuck in white screen,remove battery cover
press red botton for softrest and press "Volume down" botton
bobsbbq said:
After task 29 you have to flash a ROM. Task 29 wipes your device so if you don't hold down the volume down key at the end of task 29 it will not have any operating system. Just remove the battery and hold down the volume down key till you see the bootloader screen. Then flash your ROM and all is ok.
Click to expand...
Click to collapse
opsss..sorry bob
i have look now your post
My problem is that the windows mobile says that the phone is not connected?
What do I do now?
Thanking you in advanced,
Henry
kikimax said:
My problem is that the windows mobile says that the phone is not connected?
What do I do now?
Thanking you in advanced,
Henry
Click to expand...
Click to collapse
It won't because you're in the bootloader. Does it say USB at the bottom of the bootloader screen? As long as it says USB when the phone is plugged into your computer, flash a ROM and be happy
Hello!
And what if my hd2 not entering into the boot loader?
Thanx in advance
There is only one way to get into the bootloader.
Hold down volume and keep it down....
After that press the start button and your phone will boot up.
Now you will see the tree colored screen and you're in the bootloader.
Goodluck.
same problem..connected to pc but wmdc doesn't discover it so i can't flash anything.and sd card flash doesn't help.what can i do now?
wopin80 said:
same problem..connected to pc but wmdc doesn't discover it so i can't flash anything.and sd card flash doesn't help.what can i do now?
Click to expand...
Click to collapse
When you are in the bootloader screen, connect the phone to the computer /with the usb cable/ on the same bootloader screen it will change to USB - look at the bottom of the screen:
Open the folder - on your computer - where the ROM you want to flash is:
find the "RomUpdate*.exe" or "Install.exe" /if Android it will most likely say "DAF.exe" - run it as Administrator/ file and run it. Do as it says on the screen.
Do not disconnect the cable, do not touch the device. When it is finnished it will restart the device, disconnect the cable and enjoy your new OS.
wopin80 said:
same problem..connected to pc but wmdc doesn't discover it so i can't flash anything.and sd card flash doesn't help.what can i do now?
Click to expand...
Click to collapse
use a <4gb or preferably <2gb sd card - class 4 or 2 with LEOIMG.nbh.
HSPL3_pkg after that - make sure .nbh (as above on sd root) is your stock and you CLEAN-reinstall bootloader.
ps:
Then hspl, then radio, then magldr, then windows 7, the hacks, then call M$= LIVE!
Hi guys i have a similar problem. After task 29 i went into the bootloader but can't install any rom whatsoever. I have SPL 3.03 on my devide, mind no not hard spl but SPL. Can anyone please help me solve this issue? I also tried to flash using sd card but it doesn't work. Please help me save my hd2. Thanks in advance.
tmo-hd2 wont go into bootloader after task29
Hi guys, i am facing exact same thing which dannytgt faced (http://forum.xda-developers.com/show...count=1)...but with no luck what so ever.....was running a stock rom in my hd2 3.14....wanted to try wp7 and did a task29....after that...hd2 doesnt go into bootloader screen....tried all possible combinations with/without sd,sim, holding vol down, vol up, both with power tapped...power holded etc etc...hd2 always goes into stick together screen and doesnt progress as there is os to load....opened up the mobile and tried with a pin to push the vol down switch directly also....all hardware keys were working gr8 (including vol down and up and power keys) whn win 6.5/android was running.
i know for the fact that this is reversable....if only my hd2 can get to bootloader...i will hv os running in a jiffy....
any ideas ppl? my hd2 is 3 months old ...no warrenty cos i bought it in US and using it in india..
bootloader dont load
some more details...tried to task29 (doloop) with 100% success and then my tmo hd2 wont go into bootscreen what ever i do...its stuck for ever in "stick together"...i know there is no os to load...but i dont understand y cant my hd2 go intobootloader
so far i tried
with holding volume down and power key with a single tap
with holding volume down and holding power key
with holding volume down, volume up and power key with a single tap
with holding volume down and reset button
with/without sim
with/without SD
with/without plug in wall charger
with/without plug to pc via usb cable
observations...when i pull out the battery and put it back in and then connect to computer when the phone is still off....the charging indicator LED glows in orange.
when in this mode if i switch the phone on with power/end key....it doent start...i have to pull the usb out, the orange LED still glows...and if i tap the power/end key nothing happenes...i have to pullout the battery to get it to start and eventually get stuck in "stick together"..
would really appriciate if any1 can help me get my hd2 into bootloader screen...
gdsbalaji said:
some more details...tried to task29 (doloop) with 100% success and then my tmo hd2 wont go into bootscreen what ever i do...its stuck for ever in "stick together"...i know there is no os to load...but i dont understand y cant my hd2 go intobootloader
so far i tried
with holding volume down and power key with a single tap
with holding volume down and holding power key
with holding volume down, volume up and power key with a single tap
with holding volume down and reset button
with/without sim
with/without SD
with/without plug in wall charger
with/without plug to pc via usb cable
observations...when i pull out the battery and put it back in and then connect to computer when the phone is still off....the charging indicator LED glows in orange.
when in this mode if i switch the phone on with power/end key....it doent start...i have to pull the usb out, the orange LED still glows...and if i tap the power/end key nothing happenes...i have to pullout the battery to get it to start and eventually get stuck in "stick together"..
would really appriciate if any1 can help me get my hd2 into bootloader screen...
Click to expand...
Click to collapse
Isn't it ironic: Stick together!...
There is a guide on How to get back from WP7 here on the forum.
First i would sugest to reformat the card from WP7 bul...
If i understand correctly, you can't get into bootloader or magldr!?
So you can't do nothing?
You can try this sollution and if it doesn't work, go to the service center to reset it totaly.
There was a guy with the same problem here:
Originally Posted by splinters69 View Post
This (or something similar) happened to me. I powered down my phone but did not take out the battery and it restarted the part that loads the win 7 rom while I still got the screen with the coloured bands on.
Try, taking out the battery for 10 seconds or so then put it in while holding the volume down key and powering up.
Got stock ROM back in first time but kiss goodbye to the data on your SD card. I had to use a Canon camera to reformat the card to get back the 14GB it was hiding.
This WORKED. Thanks a TON splinters69.
For future uses, this is what I did.
1. Took out the battery for about 30 seconds.
2. Put one of the LEOIMG.NBH on storage card
3. After putting the battery held the volume down button and pressed power button.
4. It went into HSPL mode straight away and started loading the win 6.5 OS.
You saved the day Splinters69. Thanks to Clydeb1 too for that modelIDcheckbypass.
http://forum.xda-developers.com/showthread.php?t=913081
lms1407 said:
Isn't it ironic: Stick together!...
There is a guide on How to get back from WP7 here on the forum.
First i would sugest to reformat the card from WP7 bul...
If i understand correctly, you can't get into bootloader or magldr!?
So you can't do nothing?
You can try this sollution and if it doesn't work, go to the service center to reset it totaly.
There was a guy with the same problem here:
Originally Posted by splinters69 View Post
This (or something similar) happened to me. I powered down my phone but did not take out the battery and it restarted the part that loads the win 7 rom while I still got the screen with the coloured bands on.
Try, taking out the battery for 10 seconds or so then put it in while holding the volume down key and powering up.
Got stock ROM back in first time but kiss goodbye to the data on your SD card. I had to use a Canon camera to reformat the card to get back the 14GB it was hiding.
This WORKED. Thanks a TON splinters69.
For future uses, this is what I did.
1. Took out the battery for about 30 seconds.
2. Put one of the LEOIMG.NBH on storage card
3. After putting the battery held the volume down button and pressed power button.
4. It went into HSPL mode straight away and started loading the win 6.5 OS.
You saved the day Splinters69. Thanks to Clydeb1 too for that modelIDcheckbypass.
http://forum.xda-developers.com/showthread.php?t=913081
Click to expand...
Click to collapse
I hvnt even instaled MGALDR yet....task29 and hd2 went into trouble...need to get to bootloader to save it now
Tried this as well before posting....hv a 2gb sd card>formatted to fat 32> stock rrunbh to leoimg.nbh > moved to root of sd card....but this can only work if bootloader can be initiated right? i cant get to boot loader
resolved the problem myself.....hd2 is working like a charm....thanks for all your support.
SOLVED {bootloader dont load}
checkout the solution for my problem here....might help u as well.
http://forum.xda-developers.com/showpost.php?p=10644926&postcount=4
______________________________
if you feel this helped...thank me
hi there i have realy big problem i have done that task 29 trick with the blackstone advangeruu and there was something wrong after restart so i pulled the battery out.
now my phone wont do any thing when i hold nowd the start button en volume down i know it has no os. but is there any way to get in the bootloader screen hope some one can help me beceasue i need my phone.
DeAdMaNwa said:
hi there i have realy big problem i have done that task 29 trick with the blackstone advangeruu and there was something wrong after restart so i pulled the battery out.
now my phone wont do any thing when i hold nowd the start button en volume down i know it has no os. but is there any way to get in the bootloader screen hope some one can help me beceasue i need my phone.
Click to expand...
Click to collapse
Man, did you say blackstone? You should go into Blackstone forum
To go into bootloader, turn off the phone. Press volume down button and the POWER ON button (not start button) at the same time until the screen appear. It works on both Leo and Black Stone
Goodluck
I flashed hardspl and ran an android rom for about 2 hours. then the phone freaked out, and now it will not boot past the pink tmobile splash screen. so i try reflashing hspl as well as normal 2.08 spl and nothing, now the phone wont leave the 3 color screen saying rom error. what gives and how can i get back to stock? thanks for the help
Try installing an original rom from sd card.
Try this
Take batt out reinsert
Hold vol down and keep pressing it now press and release power button
In rgb screen bootloader connect usb to pc ( should change from serial to usb as u connect the cable)
Flash hspl again
Download task 29 and run it progress bar at 99% hold vol down button as phone reboots to rgb bootloader screen
Flash stock HTC Rom 3.14
This should get ur winmo back
vlx600d said:
I flashed hardspl and ran an android rom for about 2 hours. then the phone freaked out, and now it will not boot past the pink tmobile splash screen. so i try reflashing hspl as well as normal 2.08 spl and nothing, now the phone wont leave the 3 color screen saying rom error. what gives and how can i get back to stock? thanks for the help
Click to expand...
Click to collapse
Sent from my HTC HD2 using XDA App
Take a pic, your description is a bit confusing.
Take a pic of whatever screen(s) u get and maybe we can help.
sounds like the OP didn't flash a new radio when tried to run android, can we get some more info on what you did?
Hey i have the t mobile htc hd2, and i had it for quite a while. for the past year i had a windows 6.5 energy rom installed and from the last month a had battery issues. the phone whould be locked and die in 4-5 hours. i thought it was the energy rom and i decided to install magldr so i can install android on my htc phone. i have no idea whats the hspl or radio because i haven't flashed my htc in a long time.... i just installed magldr from the energy rom.... once i did that my htc would get stuck on ad recovery go go go and now i am only able to launch windows 7. when i try to nand android it gets stuck at boot. i want to change my phone back to its original state but i cant get to the tri color screen. i tried vol down then pressing power and i tried turning phone off and hold vol down and pressing the reset button, but my phone doesn't turn on when i press the yellow reset button.
mrflasha said:
Hey i have the t mobile htc hd2, and i had it for quite a while. for the past year i had a windows 6.5 energy rom installed and from the last month a had battery issues. the phone whould be locked and die in 4-5 hours. i thought it was the energy rom and i decided to install magldr so i can install android on my htc phone. i have no idea whats the hspl or radio because i haven't flashed my htc in a long time.... i just installed magldr from the energy rom.... once i did that my htc would get stuck on ad recovery go go go and now i am only able to launch windows 7. when i try to nand android it gets stuck at boot. i want to change my phone back to its original state but i cant get to the tri color screen. i tried vol down then pressing power and i tried turning phone off and hold vol down and pressing the reset button, but my phone doesn't turn on when i press the yellow reset button.[
1.First,download a stock t-mobile rom
2.Hold down volume down key while pressing the power key.
3.Connect cable to the phone and wait for usb to connect.
4.Run your rom and wait for it to finish, done.
Click to expand...
Click to collapse
First boot into magldr menu by pressing and holding the power key and scroll to usb flasher( 5 )
Connect the usb cable and wait for drivers to install,now flash your RUU,that's it. Good luck.
Click to expand...
Click to collapse
Sorry, wrong, thats for flashing android / wp7, it doesnt work for ruu's.
samsamuel said:
Sorry, wrong, thats for flashing android / wp7, it doesnt work for ruu's.
Click to expand...
Click to collapse
Thank you very much for pointing it out to me,really appreciate it boss.