Related
Since I haven't seen many people here mentioning it, I thought it'd be useful to talk about my experience with Brando anti glare protector for Touch HD.
Few months ago, when I stockpiled on the protectors, I ordered one, just for the testing purposes. They were cheap, so I figured why not.
Now that my previously used ultra-clear protector got badly scratched and even deformed after a situation in which my Touch HD fell face down directly onto a neck of a beer bottle (don't ask) I realized I had to change it. The screen magically survived without any trace of contact, and I was very lucky for having the protector on - without it, I'm sure the screen would've had to be replaced.
Applying the protector
So, I pulled out the anti glare protector and applied it. First of all, the application procedure was slightly easier then with ultra-clear. The anti glare protector seems to be a bit stiffer and requires only one side of the protector to be peeled off before application, whereas the ultra needs 2 protective layers removed. It could also be simply the fact that I got some practice with these things now... But it felt easier in any case.
Fit
As with other Brando protectors, this one is also a bit too short on the bottom. If you start directly at the top of the device screen, leaving absolutely no space between the protector and the screen edge, at the bottom side you'll end up about 1.2 mm too short. For me it's not a big problem, and I certainly don't notice this, since the bottom part is usually covered by hand or fingers, but people who insist on perfection may find this annoying. The cut out for the speaker seems to sit well in it's place, and also be aware that there is a U-shaped cut out for the front camera. The ultra clear covers the camera, but obviously because of the grain-effect I'll get to in a moment, this was not possible here.
Brightness
After applying it I was very happy with the overall look. The screen brightness was the same - I did not notice any reduction in this regard, so I can say that this is very good in terms of transparency.
Sharpness and visibility
As for the sharpness / visibility, I'm hesitant to even say it, but there is a small difference when compared to ultra clear, or no protector of course. But it's a small difference. The effect is sort of like a very, very fine grain pattern across the screen, but I can't stress this enough - it's really no big deal. I'm a photographer and I work with graphic editing software, so my eyes are trained to notice every damn detail. For most people, I would assume that they would hardly notice any difference. So, to cut the long story short - the sharpness stays the same, but you get a gentle grain effect which is usually noticeable only on white background.
To sort of get a feeling of what you can expect, I can recommend you open up a bitmap in Photoshop and add 1 percent uniform noise filter. This is about the same amount of grain you'll see on the screen when using this protector.
Resistance to smudging
One very cool thing I noticed is that anti glare protector also seems to be MUCH, MUCH better when it comes to smudges. With ultra clear, I would usually feel a need to wipe the phone after each conversation or a typed SMS. Basically, any contact with skin would cause a mess on the screen. With anti glare, this is still present, but to much lesser extent. I feel that this is a big advantage when compared to ultra clear protector.
Touch sensation and sensitivity
Well, first of all, it does feel slightly different under your finger. Right after applying it, the finger movement across the screen felt rather stiff. There was definitively more friction going on then with ultra clear, but after one or two days of usage, this effect seems to wear off, or you simply get used to it and don't notice it anymore. I can say I have come to actually like this. Oh, and there is no degradation of screen sensitivity that I noticed. I did not feel that I had to push the screen any harder then before, so this is another strong point.
Anti-glare feature
And finally, what would be an anti glare protector review, without comment on the anti glaring From my non scientific tests, the feature works very well. The glaring is indeed much reduced. I would say about 50-60% less, if not even more. Also, when you do get some glare, for example from the direct light above your head, it's much less obtrusive then with ultra-clear or without protector. The effect is subtle, and will not interrupt you from reading things on the device.
Conclusion
All in all, if you can accept the slight grain effect, this is a great thing for people who use Touch HD in bright light or simply feel annoyed with the fact that the default screen protector is so polished you can sometimes see more of your face on it than the screen itself.
So, by sacrificing 5% of visual quality, you can get about 50% more on the usability. I don't regret buy it at all - in fact I only regret not ordering more on my last purchase.
p.s. I have absolutely no connection with Brando, nor I will get anything out of writing this review. I also have to say I have been ordering stuff from them for a while now, and have been very satisfied with their services so far.
That's a very in depth review which I am sure many will find useful.
I have a Brando Ultra Clear and have recently been using my HD in the garden as the weather in the UK has been so hot and sunny recently. I thought it would never work outside because of the bright light but with screen brightness setting on full I could not believe how good it was. No strain on the eye at all with the sun behind or in front. Not sure if this is because of the HTC screen or the Brando Ultra Clear protector - I've not tried it without.
Sounds like Anti Glare is even better from your review but I would say that Ultra Clear is still very useable in bright light.
Hi, been looking for a proper screen protector but haven't really gotten to it yet..
After reading this I'm convinced, I'm gonna get myself one!
...just can seem to locate one in the Netherlands...all shops sell the ultra clear (with anti glare in the descriptive text), but not just an anti glare one.
Anyone?
Thanks
*ordered through shop.brando etc..*
are you going to post some images?
Psygnosis84 said:
are you going to post some images?
Click to expand...
Click to collapse
Not gonna make any promises, but being a photographer, I guess I should
great review...I hate glare! So, I'm ordering one of these Brando anti-glare screen protectors.
Has anyone compared this Brando anti-glare to the Boxwave anti-glare?
As you say above "The effect is sort of like a very, very fine grain pattern across the screen".
The Boxwave has this and it is almost unacceptable (to me) and was wondering if this Brando was any better (clearer) in this department.
Thanks.
zozz said:
Has anyone compared this Brando anti-glare to the Boxwave anti-glare?
As you say above "The effect is sort of like a very, very fine grain pattern across the screen".
The Boxwave has this and it is almost unacceptable (to me) and was wondering if this Brando was any better (clearer) in this department.
Thanks.
Click to expand...
Click to collapse
Hi, I haven't used any Boxwave protectors, so I can't really say, but I am interested to hear from users that tried them.
Personally, I really got used to Brando anti-glare, and I find the device much more comfortable to use in everyday situations. And I really like the fact that the smudging is MUCH less of a problem.
Anyone know where these can be got in the UK?
**EDIT** Nevermind, I got it here - http://shop.brando.com
$3 shipping worldwide, $12 in total = just under £8...
AndyCr15 said:
Anyone know where these can be got in the UK?
**EDIT** Nevermind, I got it here - http://shop.brando.com
$3 shipping worldwide, $12 in total = just under £8...
Click to expand...
Click to collapse
http://www.inkino.co.uk/zen/index.php?main_page=index&cPath=69&zenid=ebdc7d2530edpgsgpjp2v0qbb1 in Tottenham Court Road fit them for you in case you've got a shaky hand
Not sure if they will have anti glare though.
zozz said:
Has anyone compared this Brando anti-glare to the Boxwave anti-glare?
As you say above "The effect is sort of like a very, very fine grain pattern across the screen".
The Boxwave has this and it is almost unacceptable (to me) and was wondering if this Brando was any better (clearer) in this department.
Thanks.
Click to expand...
Click to collapse
Hmm, I actually prefer Boxwave's grain pattern because it gives "texture" to the screen. Yeah it does lower the screen's image quality but overall it's quite nice I reckon
I got mine today, I really like it. It has a matt finish rather than a gloss finish which I prefer the feel of.
Unfortunately it took about 8 attempts to get it on without the edges slightly overlapping and causing the long bubble along the edge and now I think I have some dust under it
Still, it's a great fit, feels great but I have yet to see how well it's anti-glare properties hold up.
Brando, not so good
I have to disagree. At first I was very excited it about it but then... I find it horrible! I was not able to use it. Could not get rid of the bubbles. I think its cut too big! Wash it and nothing but dust gets caught on the backing that sticks to the screen which has some kind of glue like surface. After washing it gets marks all over and dust. I wasted my money. Expensive, not worth it, needs work. I have installed many screen protectors on my touch hd.
Nope, nope, nope... had none of those problems here...
I've had good luck with Brando compared to other protectors.
c6638746 said:
I have to disagree. At first I was very excited it about it but then... I find it horrible! I was not able to use it. Could not get rid of the bubbles. I think its cut too big! Wash it and nothing but dust gets caught on the backing that sticks to the screen which has some kind of glue like surface. After washing it gets marks all over and dust. I wasted my money. Expensive, not worth it, needs work. I have installed many screen protectors on my touch hd.
Click to expand...
Click to collapse
All you need is a steamy bathroom.
Has anybody every used this brand of screen protector's before? They just sent me an email saying that they have in stock screen protectors specific for the T-mobile TP2 and I am debating whether or not to buy them.
http://www.boxwave.com/products/cle...screen-protector-t-mobile-touch-pro2_3668.htm
I originally had a Martin Fields on my Touch Cruise that I loved, but they don't make the screen protectors for the T-mobile TP2
I used one on my MDA (prior to getting the TP2). I loved it (make sure to get the crystal clear, not the non-glare, if they have a choice). 3 years and looks like new, nice slick surface for using the stylus, extremely durable. But I don't have experience with any others (except the one that came in the TP2 box which I also like a lot).
Thanks for sharing!
I´ll go for one of those
The crystal clear is one of the best I've used before!
I have used the Anti-Glare version for my 6700 and 6800/Mogul and love it. I used my phone in my car alot so the Anti-Glare is a must. It also finger print resistant, I'm using the screen protector that came with the phone now and the finger print smudges are just driving me nuts! I've order one and is waiting for shipment notice.
the Anti-Glare version is a semi reigid piece of plastic that make it very easy to apply, similar to the included protector, I hate those soft floppy protector that's next to impossible to put on correctly
bitslizer said:
I have used the Anti-Glare version for my 6700 and 6800/Mogul and love it. I used my phone in my car alot so the Anti-Glare is a must. It also finger print resistant, I'm using the screen protector that came with the phone now and the finger print smudges are just driving me nuts! I've order one and is waiting for shipment notice.
the Anti-Glare version is a semi reigid piece of plastic that make it very easy to apply, similar to the included protector, I hate those soft floppy protector that's next to impossible to put on correctly
Click to expand...
Click to collapse
is the anti glare version kinda gritty to the touch ive never used one?
osrix25 said:
is the anti glare version kinda gritty to the touch ive never used one?
Click to expand...
Click to collapse
Was wondering this as well. I ordered a Clear Touch while my co-worker opted for the anti-glare. I'll try to do a side by side comparison when they arrive.
bitslizer said:
I have used the Anti-Glare version for my 6700 and 6800/Mogul and love it. I used my phone in my car alot so the Anti-Glare is a must. It also finger print resistant, I'm using the screen protector that came with the phone now and the finger print smudges are just driving me nuts! I've order one and is waiting for shipment notice.
the Anti-Glare version is a semi reigid piece of plastic that make it very easy to apply, similar to the included protector, I hate those soft floppy protector that's next to impossible to put on correctly
Click to expand...
Click to collapse
Speaking of anti-glare... im using one on my Iphone 3G..got it back from Manila,Philippines on my last holiday, some chinese brand screen that i thought will be just a piece of crap screen protector.
to my surprise it was 98% perfectly fit on my iphone...and it was a great anti-glare screen protector. my wife likes it now she wants 1 for the htc touch pro2. ive seen some on ebay i might order it this week.
for those who's using one... where did you guys buys the anti-glare screen protector?? -thanks
Arcarsenal said:
Was wondering this as well. I ordered a Clear Touch while my co-worker opted for the anti-glare. I'll try to do a side by side comparison when they arrive.
Click to expand...
Click to collapse
Nice one thanks
I've raved about it before many times, just search my posts on here and PPC geeks, but the BoxWave AntiGlare is the best screen protector for any device hands down period end of story etc!
osrix25 said:
is the anti glare version kinda gritty to the touch ive never used one?
Click to expand...
Click to collapse
I wouldn't say gritty, but its definitely neither frictionless or sticky and doesn't impede your fingers or stylus movement in anyway... its got a matted texture, and I really like using my stylus with that texture! more of a paper feel, offering just the right amount of feedback and friction.
You do lose a tiny bit of clarity compare to the Crystal version, but for the anti-glare, anti-finger print benefit, I love it!
finger prints and face oil on the stock screen protector have been driving me nuts!
I'm supposed to get it today but heading out of town for a wedding this weekend so may not have a chance to report or upload pix until monday
Thanks for the report, i can imagine a paper texture! i think i may order one. cheers
What do you all think of these dedicated screen protectors, as compared to using the screen cover provided by invisibleSHIELD or Bodyguardz? Are the ones you all mentioned, or from "BoxWave" better because they are made specifically for the purpose of screen protection? Or are the I.S. or Bodyguardz ones comparable, since they are built to offer all around protection?
venomshot629 said:
What do you all think of these dedicated screen protectors, as compared to using the screen cover provided by invisibleSHIELD or Bodyguardz? Are the ones you all mentioned, or from "BoxWave" better because they are made specifically for the purpose of screen protection? Or are the I.S. or Bodyguardz ones comparable, since they are built to offer all around protection?
Click to expand...
Click to collapse
Personally, the 3M crowd is better because then you don't have to worry about the screen protector getting scratched.
I had purchased a Boxwave Anti-Glare before and it worked decently, but the amount of glare it reduced was negated by the amount of brightness that needed to be increased.
Boxwave, in my opinion, works if you have a case protecting it. But trying doing this with a Boxwave.
osrix25 said:
is the anti glare version kinda gritty to the touch ive never used one?
Click to expand...
Click to collapse
NOT gritty.
I have used Boxwave screen protectors for years and have NEVER been disappointed. Excellent longlasting product that your stylus simply glides across; I have settled on the Anti-Glare. One post says that Boxwave isn't TOTALLY scratch-free like some other 'full-body' clear protectors. Correct. However, personally I do not like the idea of spraying a liquid all over my device in the application process. 'Full-body' protectors are applied just like installing tinting on you car's windows.
Suggested application procedure.
Before beginning I have two clean microfiber cloths; one is included. Clean your phone's screen well; preferably w/one of those microfiber cloths. Close windows in bathroom, run shower on hot a bit & turn off. Moisture will pull all the dust outta the air and drag it to the floor. Vent heat (u don't want it to be uncomfortable in there).
Now that all the floating dust is negated, clean your screen again w/the the other microfiber cloth and apply protector. It is helpul to have some tape applied to a corner or two of the protector. Utilizing the tape, lift and reapply as needed using the supplied squeegee or a credit card to clear out bubbles; you may need to lift protector and use the microfiber cloth to pick up some lint/debris to ensure a clean install.
You should have a lint- and bubble-free application if you were careful.
Good luck from Lincoln!
I just got the new Boxwave ClearTouch Crystal screen protector for my T-Mobile TP2: http://www.boxwave.com/products/cle...screen-protector-t-mobile-touch-pro2_3668.htm
I had previously had a Boxwave on my MDA. That has lasted 3 years with no signs of wear, and I was extremely pleased with the fit and feel, so was hoping to do the same for my TP2. I researched all of the competition and read many forum posts on the subject. My main criteria were:
1) quality
2) exact fit
3) feel with finger and stylus
4) longevity
Price was less of a concern as I am hoping I will only ever need just the one for my TP2 (if my previous experience with the MDA is anything to go by), and so the lower priced ones, or the ones that came with 2 or 3 in the pack, were not a strong selling point for me.
The other main one I narrowed it down to was the Bodyguardz, and I probably would have got that if the Boxwave hadn't been coming out soon.
Boxwave advertised pre-orders were available for October 9th shipping. I searched high and low but couldn't google a single coupon code, so ended up paying full price of $12.95 + $2.50 shipping. They shipped a day or so late, and because of the long holiday weekend it arrived a little later than it probably could have, but as far as shipping, packaging, tracking go, I give Boxwave an A-
I had actually been perfectly happy with the screen protector supplied by HTC, but as others have noted, in some cases it may have been a tiny bit too large, causing bubbles along one edge. I think I had put it on pretty perfectly, but then, in my obsessive need for perfection, had pulled it off a little and proceeded to snip away too much screen in an attempt to get it to fit just right, making for an install that now looked a bit messy and with a bit of glass exposed along a jaggedy edge of protector. But the Boxwave fit perfectly, and very easily, just using the instructions on the package (i.e. I just put it on dry, no sprays or water). I did steam up the kitchen a bit first to try to remove dust, and obsessively cleaned the screen for 10 minutes before attempting the install. On my first attempt I started from the short top edge and that caused a problem as the protector was now not aligned correctly down the right side, so I pulled it up and laid it down again from the long left edge, making for a much easier alignment. However, when I had pulled up the protector from the first attempt, I had used the little plastic card to ease up the protector; I think I caused some very minor damage to the protector at the point of contact, as there is now a tiny minor bubble there that is probably caused by a kink I may have made in the plastic. I'll work on smoothing that out, but it's off the screen and very minor (however, let that be a warning to others to be extremely careful if you need to lift the plastic off. I tried using sticky tape but the suction was too strong for it to get a grip, and using something like a pin seemed like potential to damage the screen.) For fit and finish and ease of installation, I give Boxwave an A (and me a B- )
The surface of the 'Crystal' clear screen (I don't know how different the 'anti-glare' version would be) is very slick. In fact looking at it, touching it, sliding my finger across it, and using the stylus on it, seems exactly the same as the actual glass screen on the phone. I went into notepad and made a new note so I could doodle with the stylus. With almost no pressure I could draw lines about 90% of the time, the rest it would skip a little. But with just a tiny amount of pressure, about what you would probably use in normal use, it was at 100% coverage, with practically no drag feeling, just a nice slippery but not too slippery feel. Sliding with my finger is fantastic, I can now scroll through the programs screen much easier than I did with the original HTC. For sensitivity and surface texture I give it an A+
Overall I give Boxwave and the Cleartouch an A+. I am reminded of that old Memorex commercial 'Is it real, or is it Memorex', because looking at the phone right now, I can't tell it has a screen protector, it looks just like glass. I am sure there are others out there as good, although I doubt there are any much better. There are certainly other quality ones that are much cheaper, $15 seems like a crazy price to pay for a piece of plastic. Others come with 2 or 3 protectors, and many have coupon codes you can find on Google. And others, like Bodyguardz, come with a solution for complete protection, not just the screen. Of course time will tell, but based on my A+ experience with Boxwave on my MDA, I really am quite confident of the same longevity and performance on the TP2.
One happy customer.
I've used Boxwave screen protectors and accessories for the past several years, and I can honestly say I've been always 100% pleased. I've used both the antiglare and clear protectors, and prefer the clear ones - but it's all a matter or preference, but overall a good purchase.
First, Boxwave screen protectors have always been my standard. I've tried a couple other types (mostly what's been included with devices or what I can find in retail stores) and won't likely be messing around with that again. I personally prefer the "crystal" models over the anti-glare because I didn't like the affect of the anti-glare pattern on the display. It kind of gave it a fuzzy moire pattern. The crystal basically looks like those super glossy laptop screens - looks great in low/medium lighting but could be a problem in certain direct light situations. Still, the trade-off is worth it to me.
Second, does anyone know if any of the existing TP2 protectors will fit the AT&T Tilt 2? The European/UK model looks not ideal because of the front camera hole and the T-mobile version appears to have a slightly different button layout on the bottom. Both the Verizon and Sprint models look right to me on the web page, but Boxwave support just says to submit a request and wait. I would prefer to get a protector on mine ASAP but am reluctant to order if the fit isn't right.
Daniel
bought one for my Sprint Touch Pro 2, it applied perfectly and not noticeable at all. I prefer it way over the invisibleshield I had on my Vogue which was too rubbery and reflective.
Am I correct to think the Boxwave screen protector for the Sprint TP2, Verizon TP2, and the ATT Tilt 2 are the exact same thing? I have been looking at pictures and the screen shapes look identical. The only different ones are the T-mobile and the front facing camera versions.
Thanks!
Has anyone bought an anti glare protector for the screen? I know there is a screen protector topic but they were more focus on just protecting the screen and not about anti glare.
acuralegendz said NuShield anti glare protector was only ok. I rather not pay 25 dollars for an average product.
I also saw link to Lexerd - Viewsonic G Tablet TrueVue Anti-Glare but I havnt heard any reviews on it yet.
I just ordered it yesterday from Amazon, as soon as it's in I'll be happy to let you know.
andygee said:
I just ordered it yesterday from Amazon, as soon as it's in I'll be happy to let you know.
Click to expand...
Click to collapse
I am going to assume that you are talking about the Lexerd - Viewsonic G Tablet TrueVue Anti-Glare. Can you test it in sunlight and indoor light? Thanks a lot
Yes I am, and yes I will be happy to. I don't think it will be here until the end of the week though so will be a few days.
i just installed this screen protector and I must say that the price is ridiculous for the quality.
It makes the screen quality completely grainy. Maybe I have to let it sit for a few hours.
Nice to the touch, has a mat feel. doesn't seem like it effects the touch sensitivity.
the edges are horrible. I can see it lifted all the way around the entire screen and i have no bubbles or dust around the edges but that will change soon. I just hope that as more dust gets trapped under the lifted edges, it doesn't make it worse over time but we will see.
I'm use to the screen protectors where you apply them on like window tints (Body Guardz brand). Had them on my ZuneHD, Droid1, Doid2. All perfect..Lexerd, not even close.
My opinion is that this screen protector should have been 10 dollars. sucks I got the double pack. sigh.
Adding pictures below
pics attached.
stigmax said:
i just installed this screen protector and I must say that the price is ridiculous for the quality.
It makes the screen quality completely grainy. Maybe I have to let it sit for a few hours.
Nice to the touch, has a mat feel. doesn't seem like it effects the touch sensitivity.
the edges are horrible. I can see it lifted all the way around the entire screen and i have no bubbles or dust around the edges but that will change soon. I just hope that as more dust gets trapped under the lifted edges, it doesn't make it worse over time but we will see.
I'm use to the screen protectors where you apply them on like window tints (Body Guardz brand). Had them on my ZuneHD, Droid1, Doid2. All perfect..Lexerd, not even close.
My opinion is that this screen protector should have been 10 dollars. sucks I got the double pack. sigh.
Adding pictures below
Click to expand...
Click to collapse
Thanks for the review stigmax. That sounds horrible even at 10 dollars. FYI there was a one pack of those protectors but little late to tell you that now.
Yea, I knew about the single pack but thought I could save a few bux with the double. After a few hours of use, my eyes got use to the grainy screen
Temp protector I guess, at least I dont have to worry about scratches: )
What I haven't seen elsewhere is that on the "Thank you for purchasing..." sheet that came with the G Tab, it states: "1. The device may come equipped with two anti glare screen protectors over the screen; which should be removed". Huh? Why two? Why remove them. It doesn't make sense. I assume because there is glare, that mine didn't come with them.
murdockr said:
What I haven't seen elsewhere is that on the "Thank you for purchasing..." sheet that came with the G Tab, it states: "1. The device may come equipped with two anti glare screen protectors over the screen; which should be removed". Huh? Why two? Why remove them. It doesn't make sense. I assume because there is glare, that mine didn't come with them.
Click to expand...
Click to collapse
Because at some point there were so many returns (at sears and staples) because of claims of a defective screen which later turn to be some air bubbles trapped under the second layer of the screen protector
I really like my nushield dayvue anti-glare protector. Puts my gtab on par with my xoom visibility wise.
Sent from my Xoom using Tapatalk
Anti-Glare
So has anyone found any good Anti-Glare that are not $30? just trying to find a good screen protector and case so I can stand it up and watch movies if need be.
Ever try Photodon?
http://www.photodon.com/p/MXH-5250-01.html seems nice based on their description but wondering if anyone ever tried one.
I ordered this set a couple weeks ago. One is clear and one is anti-glare:
http://cgi.ebay.com/ws/eBayISAPI.dll?ViewItem&item=290551331136&ssPageName=STRK:MEWNX:IT#ht_570wt_1140
They fit the screen perfectly. A little too perfectly actually. It's somewhat difficult to get the protector perfectly straight so that one side or the other doesn't run into the edge of the screen where the edge slightly goes up. I rendered the clear protector relatively useless after attempting to line it up perfectly several times.
Neither of the screen protectors have cut outs for the camera or the light sensor. It doesn't seem to really affect the light sensor, but the anti-glare protector makes the camera pretty much unusable. The camera is fine with the clear protector on.
The reason it makes it unusable is because of how grainy it makes the screen look, and that grain is also visible through the camera. It makes everything blurry. That said, it does a good job of reducing glare as well as a pretty darn good job of cutting down on visible finger prints. I've found that the graininess isn't extremely intrusive for most things. Maybe I've just gotten used to it.
One of the main reasons for purchasing my gTablet was to use it as an eReader for the hundreds of .pdfs I'm required to go through. This is where the grain really becomes troublesome. If it wasn't for the fact that somehow I managed to get the protector on perfectly straight on the first try, I would have already removed it. I'm thinking about ordering another set, cutting out a hole for the camera, and going with the clear protector. I'll make due with some glare here and there and some fingerprints.
bsweetness said:
I ordered this set a couple weeks ago. One is clear and one is anti-glare:
http://cgi.ebay.com/ws/eBayISAPI.dll?ViewItem&item=290551331136&ssPageName=STRK:MEWNX:IT#ht_570wt_1140
They fit the screen perfectly. A little too perfectly actually. It's somewhat difficult to get the protector perfectly straight so that one side or the other doesn't run into the edge of the screen where the edge slightly goes up. I rendered the clear protector relatively useless after attempting to line it up perfectly several times.
Neither of the screen protectors have cut outs for the camera or the light sensor. It doesn't seem to really affect the light sensor, but the anti-glare protector makes the camera pretty much unusable. The camera is fine with the clear protector on.
The reason it makes it unusable is because of how grainy it makes the screen look, and that grain is also visible through the camera. It makes everything blurry. That said, it does a good job of reducing glare as well as a pretty darn good job of cutting down on visible finger prints. I've found that the graininess isn't extremely intrusive for most things. Maybe I've just gotten used to it.
One of the main reasons for purchasing my gTablet was to use it as an eReader for the hundreds of .pdfs I'm required to go through. This is where the grain really becomes troublesome. If it wasn't for the fact that somehow I managed to get the protector on perfectly straight on the first try, I would have already removed it. I'm thinking about ordering another set, cutting out a hole for the camera, and going with the clear protector. I'll make due with some glare here and there and some fingerprints.
Click to expand...
Click to collapse
I'm curious if you could use a hole puncher to make a hole for the camera? I have not seen this product so I have no idea what it is like or how thick it is but seems like it could be modded with a hole punch if you do the measurements precisely. Anyways, just a thought I had while reading. Thanks for the review.
jetguy35 said:
I'm curious if you could use a hole puncher to make a hole for the camera? I have not seen this product so I have no idea what it is like or how thick it is but seems like it could be modded with a hole punch if you do the measurements precisely. Anyways, just a thought I had while reading. Thanks for the review.
Click to expand...
Click to collapse
You know, right before I put mine on, I thought to myself - "Should I run out and get a hole puncher for the camera before I do this? No, it should be fine."
I should have went to get a hole puncher. It would work perfectly.
Happy with my Protector
mernst2 said:
So has anyone found any good Anti-Glare that are not $30? just trying to find a good screen protector and case so I can stand it up and watch movies if need be.
Click to expand...
Click to collapse
I bought a matte one and a clear one from Aurum, but fit really well, I think you get get both for under $20. The matte reduces glare and the clear one does not distort the screen. Overall was very happy with the product. The Lexard one and those other "wet" applications ones are a pain in the ass, they also prevent your finger from gliding smoothly on the after application. I got them at Amazon here is the link http://www.amazon.com/s/ref=nb_sb_s...rum+viewsonic&x=0&y=0&sprefix=aurum+viewsonic
NuShield antiglare sheet or DayVue?
Synman said:
I really like my nushield dayvue anti-glare protector. Puts my gtab on par with my xoom visibility wise.
Sent from my Xoom using Tapatalk
Click to expand...
Click to collapse
Just called NuShield, as their site does not work well with IE9 when placing orders, and was told they are currently NOT selling an "antiglare" sheet for the gTablet. They only have their "DayVue" product, which does not have anti-glare feature.
However, if you contact them, they very likely would consider making an anti-glare version as they already have a template for the gTablet.
[email protected]
I was just looking at their website and it describes the DayVue as anti-reflective. Straight from the website under Viewsonic GTablet.
NuShield DayVue™ antireflective film is the best choice for displays that are being used outdoors. It has good scratch resistance combined with greatly improved daylight readable optics over our antiglare film.
I don't know if they consider anti-glare and anti-reflective to be different, but it seems like the same to me.
ive got an antiglair, it works well and was only 10$ off amazon but if you like using it for videos it kills them, thinking about removing mine but i have a hard time throwing 10$ away
I've been looking at some reviews including a very lengthy one from a couple of years back on Youtube where he tried about NINE different brands (Including anti-glare or crystal from the same manufacturers) and he tried pretty much most of the known brands including Zagg. He did miss out Martin Fields and a few others though.
I've seen the XO skins are pretty easy to apply wet. Much easier than the Zagg.
XO aplication.
http://www.youtube.com/watch?v=-Td0vTcKMME&feature=related
Brief thumbs up from someone.
http://www.youtube.com/watch?v=VJGJKH8BGz0
XO skin for TF
http://xoskins.com/laptops-tablet-r...ors/asus-eee-pad-transformer-screen-protector
Large shooutout of various screen protectors. But it's a couple of years old and for a tablet PC rather than pads.
http://www.youtube.com/user/tonkabui#p/u/0/9XdVHL1M7vM
I am going to continue looking. But if anyone finds the perfect screen protector let me know. That XO looks easy to apply. But I want anti-glare and anti-reflectin as well as anti-smudge and 0 bubbles (in other words eacy to apply). Protection from scratches is actually pretty low down my list of wants.
If anyone can post their experiences (good or bad) of various screen protectors please do so here. I noticed there is a reasonably priced TF1010 anti-glare protector made by Posr.us and has two five star reviews on Amazon. Also someone called MFX is making one as well as Martin Fields and SGP Steinheil.
Thanks I needed one still and this looked decent and easy to apply (I prefer the wet application) I bought it and used coupon code "retailmenotxo" for 15% off ... it covered more than the shipping so that was cool.
I put on Skinomi on my beloved transformer. yeah it's a wet app, and I'm not yet skilled in it's application yet, but certainly feel much safer with it on than not - even despite the alleged "scratch resisteance of Gorilla Glass"
well my screen has a scratch only had it a week
rgalarza75 said:
I put on Skinomi on my beloved transformer. yeah it's a wet app, and I'm not yet skilled in it's application yet, but certainly feel much safer with it on than not - even despite the alleged "scratch resisteance of Gorilla Glass"
Click to expand...
Click to collapse
Well, scratch resistant =/= scratch proof, so all those people who say Gorilla Glass is the reason why you shouldn't need a screen protector are fooling themselves. I personally have a clearfreak protector on my transformer. It definitely makes me feel more at ease when I use it.
I bought two of the (as far as I can tell) unbranded screen protectors from ElectronicCrap.com. Other than the non-existent directions, I'm quite happy. Not terrible with the fingerprints, reduces the glare, feels and appears quite durable. Price seems a tad steep (given that you can get whole packages of universal ones for like $10) but these fit perfectly edge-to-edge with the cutout for both the light sensor and the camera. It didn't come with directions of any kind but it's a screen protector - it isn't rocket science. I'd say overall it's a keeper.
I picked up a dcmugen antiglare from ebay and I love it. Damp or dry install, the type with the two peel off layers, and repositionable to boot. It ships from Asia, and mine came with a slight crease causing bubbles that cant be flattened. I've requested a replacement, waiting to see if they follow through. So much easy to use indoor and out, and far fewer fingerprints to clean off.
Sent from my Transformer TF101 using XDA Premium App
Got a zagg at bestbuy today because I was bored more or less. Installation went well even though the thing stuck to itself. But a few hours later and I'm bubble and wrinkle free nd protected. Now to decide if I want a spg crytal or not....
mybikegoes200 said:
I bought two of the (as far as I can tell) unbranded screen protectors from ElectronicCrap.com. Other than the non-existent directions, I'm quite happy. Not terrible with the fingerprints, reduces the glare, feels and appears quite durable. Price seems a tad steep (given that you can get whole packages of universal ones for like $10) but these fit perfectly edge-to-edge with the cutout for both the light sensor and the camera. It didn't come with directions of any kind but it's a screen protector - it isn't rocket science. I'd say overall it's a keeper.
Click to expand...
Click to collapse
I bought one as well, but it looked like crap on mine. Hen again im terrible at applying these things. I usually let Verizon put screen protectors on my phone.
Has anyone tried the skin protector from PhantomSkinz? I have their carbon fiber back skin and it looks great and is durable
Sent from my DROID X2 using XDA App
My experience with Zagg has been mixed with all my devices but their customer support is good. If you get a bad protector(line down middle, or little imperfections) they will send you another.
The XO skin looked very promising, and for $10 cheaper I thought I would give it a shot. Just placed an order for the XO skin.
Use discount code retailmenotxo for $3 off(free shipping pretty much)
Pulled the trigger on an XO
after watching all the youtube reviews, i decided that the XO looked best.
ordered one this morning.
just a thanks to all the folks responsible for putting the links and testing together in one place for time-challenged guys like me.
btw, i think the transformer is one of the smartest purchases i've made in the last few years. i'm thoroughly enjoying it.
marvin
Following up on my earlier post. Installed the XO skin in my university's clean room(0 dust, yes I wore the cleanroom suit) and it has streaks. The protector quality is very good but once you put it on there are visible streaks all over. I kept the applicator wet so there would not be "burn marks" as specified by the instructions.
Going to ask for a refund... maybe I'll give Zagg another try. My first ZuneHD protector was wonderful but the 2nd one I got had a big line down it(bad QC).
The perfect screen protector
I always have problems applying the screen protectors to any of my devices, so I did some research and decided to go with one made by a company called Aurum. The deciding factor was that it had a large cut out for my camera so its easier to apply. Overall, I am very happy. I got the two pack in case I messed up the first one.
http://www.amazon.com/Asus-Eee-Pad-...4?ie=UTF8&s=electronics&qid=1308242480&sr=1-4
I dont think I will ever buy the wet applicator types again, the dry is just simpler and gives me choices in whether I want a clear or the anti-glare. Hope this helps
Here is the link to the anti-glare offered by Aurum in case anyone is interested: http://www.amazon.com/Transformer-M...1?s=electronics&ie=UTF8&qid=1311083745&sr=1-1
I usually get Bodyguardz for all my gadgets (mostly phones). It just feels better than Zagg's invisible shield and other screen protectors.
Anyone tried using Bodyguardz? I'm thinking about getting either the full body protector or just the screen protector. Hmmm this is tough.
Following up... after 24 hours drying/curing it looks much more acceptable. The funny part is there is a tiny black spec under the protector. I don't know how it got there since I was in a cleanroom!
Found this one in Amazon, similar to the Aurum with anti-glare.
Anyone has used this ? Is this any good ?
HandHelditems - Anti-Fingerprint, Anti-Glare, Matte Finishing Screen Protector (3 Pack) (Free HandHelditems Sketch Universal Stylus Pen)
http://www.amazon.com/gp/product/B0056K5D0G/ref=ox_sc_act_title_2?ie=UTF8&m=A1NOY9EOR8TXD6
Hmmm... I have previously considered to buy it too, but I've seen the Gorilla Glas Test with the Transformer in a YouTube video... you dont need a screen protector
I just got a screen protector from Photodon. Their MXA film is great. It was a bit of work to put it on with no dust and correctly aligned. But once it's on it looks pretty good. It's got a glossy finish, so it looks just like the original screen. You can hardly tell that there is a screen protector on the transformer. It is pricey at almost $20.00 each, ut the screen is still sharp and crystal clear with none of the haze that a lot of cheap screen protectors have.
xxx.photodon.com/p/MXA-5445-01.html
I used to have Bodyguards for my HTC Touch Pro and it peeled after three months both times that I used them. Now I use Phantom Skinz and I get no orange peel effect and I've had one on my HTC Evo 4G for almost 1 1/2 years with no peeling and no orange peel effect. Smooth as glass and you can't even tell it's on there.
Now I have Phantom Skinz screen protector on my TF and Phantom Skinz Chromatics white carbon skin for the back side. Very nice to say the least.
I would highly recommend a screen protector for the TF because although it has Cornings Gorilla glass, it sux for finger prints and fingerprints are easier to wipe off of a sceen protector than the Gorilla glass.
im using the steinheil Ultra Crystal. also use it on my phone.
Reserved.
Previous thread was closed due to not being able to to accept any more requests.
Please post reviews here instead, thanks!
Now Taking Orders! PM me for details. Only post in this thread if you can't PM yet.
Saved for video review
I got the cover today, went on the first time without airbubbles, but unfortunately I got a a hair stuck under the cover. I got it on right the second time, and I'm really loving tthe cover. Its great for reducing the finger prints and glare. It is very smooth and doesn't have the orange peel texture of a lot of other screen protectors, I wouldn't mind getting one for my Droid Charge.
I got mine last night. Brought it to work this morning and slapped it on.
All I can say is I hate air bubbles and this went on the first time without issue.
It is smooth, cut down on the glare, fingerprints less noticeable, and it looks fantastic...
I am absolutely impressed by this. I may have to find out how to get a spare.
Nice can't wait to receive mine and write up a review. Hopefully my stylus will be in at the same time so I can let you know how it works with the stylus.
Recieved mine this morning. The install went smoothly, very few air bubbles that were easy to work out. The tip for removing dirt/hair trapped under the cover was great. Cover does really reduce glare and fingerprints nicely. I like the texture of the cover, it is not as smooth as the TF glass, just right to let fingers glide without grabbing.
All in all I would buy this cover.
Thanks
Just received mine today, install was easy and air bubble was easier to get out compare to what i have used before. Pretty good cover i'd say.
Just got mine as well today, install went reasonably smooth. There are a couple imperfections, but those were my fault and not the products fault. It definitely reduces the glare, and I don't notice fingerprints at all. The camera hole lines up perfect and doesn't affect it at all. Definitely one of the better screen protectors out there. The tip for getting rid of dust worked great.
I will try and get a better picture later; camera didn't want to auto focus properly.
Thanks all for the reviews. I will be posting a BUY thread in the Marketplace section once I get a few more reviews. These will be retail units with complete packaging. So keep those reviews coming!
PS Anyone recommend a cheaper/faster shipping alternative? I'm shipping them via USPS First Class ~$1 to $2 depending on location.
PPS Looking forward to the video reviews
Just got mine. Went on as easy as any screen protector I have tried. No problem with bubbles, reduces prints and glare, also the fit is spot on, only negative comments would have to be that it's not as smooth as glass. I would recommend this product.
Got mine today. Slapped it on, luckily no hair\dust. Minor bubbles which im slowly seeing go away. Glare is minimal as well as the fingerprints. By far much better than the one i received with my case from amazon. Putting an affordable price on it should make you and lots of users happy. Id buy another if need be. Thanks
Thanks to cheinb once again for the free sceen protector your generousity is greatly appreciated.
Received my Screen protector this morning in the mail and was dissapointed to see that customs or the mailman (not sure who was to blame) had decided to fold the package in half.
Despite the crease i still managed to get it to flatten out enough to be useable so I proceeded to line up the edges and found it to be a perfect fit, nice!
The finish on the screen protector adds a matte effect to the display helping to reduce glare in a sunny/brightly lighted environment, welcomed as another added bonus no doubt. The smooth surfaced finish also seems to attract significantly less fingerprints and makes the scrolling and swiping flow better.
In summary i am more than pleased with the build quality and perfect fit of cheinb's asus transformer custom screen protector, now to see how it will stand the test of time and close encounters with my monsters i mean children.
thanks again cheinb good looking out!
I received mine at the beginning of the week, and had absolutely zero problems installing it. I've installed many screen protectors in the past, and this had to be the easiest one I've ever done. The instructions were simple, and I had barely any bubbles that were slowly dissipating.
The feel of the screen protector is great, just the right amount of slide and it really cuts down on the glare.
All in all, one of the better screen protectors I've used, in all categories (Installation, protection, glare reduction, surface feel).
The TF is uses corning gorilla glass, really no need for screen protectors, unless you plan on throwing your devices around. Check youtube for gorilla glass reviews.
Sent from my Transformer TF101 using xda premium
still waiting on mine
fliparsenal said:
still waiting on mine
Click to expand...
Click to collapse
hey Fliparsenal,
You were one of the first batch. Let me know if you still haven't received it in a few days.
chienb
Good!
I got mine yesterday and also applied it yesterda.
The protector is quite thick and sturdy. There was a small paper with sintructions as well.By design it allows for less air bubbles and I have only a few minor ones on the sides because of my in experience.
It has reduced the glare and made the screen less slippery. Fairly thick and I am sure it will last for a long time. The adhesive is also pretty strong. Would have been even greater with a slight blackish tint.
In short I recommend it.
fliparsenal said:
still waiting on mine
Click to expand...
Click to collapse
Same here nothing yet.
Excellent
Received mine the other day, and have had a few days to use the protector.
The following is my opinion. Screen protectors aren't for everyone, but personally I'd rather make a $20 'oops' than have to live with scratches. I don't see the harm in a protector, and in my experience they reduce fingerprints and glare like mad... so, do what you want.
Anyway, here's what I think of this protector:
Installation:
Handy set of instructions. Protector went on without any problems. I used a credit card as suggested to get rid of the air bubbles, which worked out very very well. This installation method is much much easier (and safer?) than Zagg, and similar to other adhesive-type protectors.
Fit:
The protector is cut slightly smaller than the size of the glass. My alignment was spot on, so I don't have any air bubbles around the edges, but there is probably a 1mm (or less) gap around the outside of the protector, which in my opinion is the perfect fit. The cutout for the front camera also is perfect.
Feel:
The protector offers minor friction for fingers. Initially my hands were very clean from the application process, and therefore were not leaving any finger prints. I have since used the TF for a few days, and even let a baby with greasy hands play with it, and the fingerprints/smudges were a minimum. In summary: the protector feels VERY GOOD and appears to cut down fingerprints like crazy. For me, this protector is better than just the glass, and much much better than the protector I had before (I had some 3 for $10 ebay style protector.. it was garbage). This protector is on par with Zagg protectors and their lack of fingerprints (for those who have used them).
Look:
Its hard to tell that there's even a protector on except for a few pieces of dust. Glare is reduced, colors don't seem to be affected. The protector I had before this one was much worse for letting the true colors through. Everything was faded and coarsened (dunno how to best describe that, but it looked bad). All in all, this one looks as good as no protector, with added benefit of reduced glare and minimal fingerprints.
Overall:
Most of my protector experience is with Zagg protectors; on a Nook Color, galaxy s and iPhone. I didn't want to have to fight with putting a Zagg on for a screen the size of the TF, so I have been looking for alternatives. If this protector is competitively priced then imo its one of the better ones for the TF. I once tried a skinomi for a G-tablet, and that thing was a complete waste of money.
Pending price, would get another one of these.
Thanks OP for the protector.
Keep us updated on their availability (I'll probably get another one).
Another question: would it be difficult to make one to fit a G-Tablet?
Cheers.
Ok I've finally received mine. Unfortunately the the package must have gotten folded during transit and it now has creases. I'll make do and will post a tutorial next upcoming weekend. Hopefully the crease is not permanent.