[Q] Semi bricked, no buttons work, jig no go - Vibrant Q&A, Help & Troubleshooting

so I made an ultra bone head move. I orginally bricked my phone to hte point it said AST_STAT in red text I think learned of the vol up and down tick to put iit into download mode. I was able to flash and had a working device again although be it 2.1.
I should of really stopped at this point, I figured man that was easy I'll get the latest firmware and get back up to 2.2 well it bricked again I have the computer, phone and the ! I figured okay no problem its not as bad as last time right?
WRONG none of the button combos work and I bought a jig from mobiletechvideos.com and that just displays the same thing as above I can't get into download mode to save my life on my phone.
I've got a new one coming from T-Mobile as a swap but seriously the $450 axe they have hanging over my head doesn't feel so good I know there was a similar thread but it never went anywhere there was no resolution and I'm hoping one of you fine posters will have a trick to help me out of this jam.
I've tried every button combo nothing seems to do it I just couldn't leave well enough alone lesson learned but I'm hoping there is still a way out.
Thanks everyone!

...What did you try flashing that first time?
It wasn't per chance something that contained bootloader like one of the new Gingerbread ROMS was it? A few of them still have bootloader flashes which can brick you.
It would be helpful if you listed what you tried flashing and the steps you took.

When I brick like that, that's the only screen I get. If Odin sees your phone, you can flash it. The !--pc screen doesn't matter.
Sent from my GT-I9000 using XDA Premium App

Orginally flashed it with T959UVJFD.tar and 512.PIT using ODIN3 1.0 ODIN does see my phone I'll keep giving it a shot it kept freezing at Cache.rpf but persistence might pay off.
Thanks for the quick replies!

You should try using Odin 1.7. I found it works best.

Soo who wants the first handy J in the corner? J/K you guys are ****ing amazing you will be dumbfounded none the less.
So here is my situation.
MY Rig:
Dell XPS 420
Win 7
Wife's PC
Custom built Win 7 with ABIT Mobo
I D/L ODIN 7 it fails again at Cache.rfs so I pull the plug just like the first time around I turn it on and notice it isn't turning on quickly anymore so I use hte JIG BOOM DOWNLOAD MODE!!
My XPS will not flash my phone to save my life so once again I flashed on hers using ODIN 1.0 and same FW as mentioned above it failed on cache.rfs and I pulled the plug and put it in download mode again using two button (vol + -, USB + Battery) and it flashes it fine.
Seriously I'm in debt and I so want to move to CM 7 as my buddy runs it on his t-mobile 4G (the very first 4g phone can't remember name) but I think I'm just going to hold my horses on doing anything for awhile
I honestly think the XPS 420 chipset might not be good for flashing android phones I never ever could get it to go I even tried in a virtual environment running XP and same exact thing occurred every time.
sorry to repeat myself but thank you, thank you, thank you, thank you!

Related

[Q] First time rom user = now i have a brick

Hi XDA, firstly wow...great site, lots and lots and lots of info, seems like a great community.
My phone: SGH-T959 (Samsung S Vibrant)
My issue: After flashing Axura 2.2.7 my phone doesn't turn on...at all...ever!
History: I'll say up front that I'm a long time android user with a technical background (Windows, Cisco networking, light Linux, etc) but first time rom flash experience. I bought a used SGH-T959 off Ebay, came stock with android 2.1 stock, I used Samsung Kies (straight off the official site) to upgrade to android 2.2. Well the phone slowed down, a lot. I felt ready to try my hand at flashing a Rom.
I first did a lot of reading, got Odin and my 2.1 and 2.2 stock files, flashed to 2.2 just to get a little comfortable. Worked fine. I charged my battery to full and then started the process of rooting my phone, again worked fine. I then updated to E2 boot loader (if I remember correctly) so I could work in recovery mode. I rebooted for good measure after going to E2 and all was still well.
**Issues incoming***
Using Clockwork I rebooted into recovery, flashed Axura 2.2.7 and the phone froze. Almost in a panic I pulled the battery and the phone was fine, still in stock 2.2. I booted to recovery again via Clockwork and attempted to flash Axura again, completed this time so I rebooted. That's the last time my phone did anything but look like a shiny rock. Will not power on.
Things I have tried:
* Holding many, many different combos of buttons after reinserting the battery
* Bought a usb Jig off ebay, nothing happened when inserted (tried holding many different combos of buttons while inserting it and while inserting the battery)
* Holding many, many different combos of buttons after connecting the USB cable to my computer with known good USB drivers (from when I used Odin)
* Used a known good battery from another T959 phone (co-worker that has same phone)
* Just for kicks I registered the device with Samsung, had two days left on the one year manufactures warranty so shipped it back to them, they returned saying the phone had experienced water or corrosion damage and the warranty was void.
As to Samsung's response I would like some feedback as to the possibility (it was a used phone after all). Just seems very unlikely that the phone would die just as I flashed it...
I am at a loss, I would love to get some helpful hints, tricks or anything else I could possibly do to get my phone back into download mode. I feel confident that if I could get the phone to that state I could get the process right.
Tell me I didn't waste my money on a now dead phone, give me some hope.
your best option is taking it to repair shop
don't know the point of using kies. Don't think it's a necessary step.
try these instructions: http://rootzwiki.com/topic/605-guid...nja-apps-everything/page__p__11106#entry11106
You can probably start on step 2 since you have nothing to back up. This will bring you back to stock and try flashing again. I use these instructions all the time before i flash a new rom
Good luck and keep us posted
Thanks for the link, however as I said in my OP, I have used Odin before and am comfortable with it, the phone doesn't turn on, aka no download mode)
It seems Jtag repair is my last hope (unless anybody gets creative and surprises me), anybody recommend one?
I searched and found one for $40 - mobiletechvideos.mybigcommerce.com/samsung-vibrant-jtag-brick-repair
Anybody review or offer an alternative?
TRY THIS
1) pull the battery out
2) plug ur usb wire to ur pc and ur phone
3) hold volume up+ wolume down
4) insert the battery in
GOOD LUCK...
try to odin back to stock
1. Start Odin
2. Plug USB cable into pc
3. Power off the Phone.
3. Pull the Battery.
5. Plug USB cable into Phone.
6. Press and Hold: Volume UP + Volume DOWN + Power, all at the same time.
7. Re-insert the battery.
8. The phone will power now, when the screen starts a cycle of going to a BLACK screen, release ONLY the POWER button.
9. When you see the download icon release the volume buttons,
10. Odin back to stock by putting the PIT file into the appropriate area and the .tar in the PDA area.
Or try that same method without holding the power button, just the volume rocker (up and down) when plugging into usb that works for some ppl
The vibrant is tough to hard brick so keep trying
I'm not really aware of the "E2 Bootloader" link maybe.... The only bootloader that I'm aware of is the Gingerbread bootloader. Either way I just posted this maybe it will be of help to you as well.
http://forum.xda-developers.com/showthread.php?p=19481353#post19481353
Keep in mind to have ODIN up when trying to get into download mode, if the phone screen is dead the only way to know you are in download mode will be the yellow box in ODIN when your device connects.
Good luck!
did you try with the battery IN:
volume UP + HOME key + POWER......?
I don't really see many people mentioning that option for DL mode....
Want to say thanks to everybody for the sugestions.
At this point after trying all the above and many more, I'm still dead in the water, I'm deciding between the $40 unbrickable mod install + flash to stock and the $40 JTag fix repair from mobiletechvideos.com
Anybody have experience with either service?
No, but this could be throwing good money after bad, however scorpn on the tw web site has a 8.00 roughly jtag, on a blackscreened brick it may not work. But it might, probly shouldnt be pimping another website, but thats where it is.
mog44net said:
Want to say thanks to everybody for the sugestions.
At this point after trying all the above and many more, I'm still dead in the water, I'm deciding between the $40 unbrickable mod install + flash to stock and the $40 JTag fix repair from mobiletechvideos.com
Anybody have experience with either service?
Click to expand...
Click to collapse
The only experience I have is a JIG. Have you seen his youtube channel? He has a lot of good info. He really knows his stuff. I learned how use ODIN and the FFC Mod from his videos. I think he has a video showing how to fix your phone or if you ship to him, he will fix it for you.
Try send a PM to him...his username is "connexion2005"
Let me know what happens or if you were able to fix your phone....
Sugartibbs said:
No, but this could be throwing good money after bad, however scorpn on the tw web site has a 8.00 roughly jtag, on a blackscreened brick it may not work. But it might, probly shouldnt be pimping another website, but thats where it is.
Click to expand...
Click to collapse
Yeah, if it were a straight $40 I would just dump the phone, bite the bullet and purchase another device. However on the site it says if the phone ends up being non repairable there is only a $10 charge to cover return shipping.
If I can install the unbrickable mod for $40, flash it back to stock, ship it back to me then I can drop whatever rom I want on it, all the while being able to use unbrickable mod apps to one click restore it...sounds worth a $10 loss chance to me.
Closfig1 said:
The only experience I have is a JIG. Have you seen his youtube channel? He has a lot of good info. He really knows his stuff. I learned how use ODIN and the FFC Mod from his videos. I think he has a video showing how to fix your phone or if you ship to him, he will fix it for you.
Try send a PM to him...his username is "connexion2005"
Let me know what happens or if you were able to fix your phone....
Click to expand...
Click to collapse
I actually did buy a USB Jig (OP), still nada on the display and ODIN com check.

REALLY bricked!!!...

I was trying to Odin back to 2.2 eugene, and after about 30 secs...screen went red...and stayed there. I unplugged the battery, and tried to get back to DL mode...FAIL. I tried all methods , searched the forum and google for hours and can find no solution. The phone is flat out dead. Will not power on, cannot get to DL mode...nothing. I did notice before this happened, that when I was trying to transfer CWM files for a new ROM to flash, the SD card didn't seem to mount. Didn't realize it until I went into recovery, and I was looking at only the ex/sd. Any ideas short of using it for spare parts ( i have two, this one is my wifes) and buying a new one?
Please help!
2.2, are you on a 4g?
No...its the old 3G...was going to redo GB on it because it had been acting up as of late...ROMs I were using were switching back and for from #G to "H" though... This thing is super dead, no pwer nothing. Been flashing and dealing with brick problem for a while on these things, and I usually can get them going...I think this one is gone though...
I've tried every method i can think of or find to get back to DL mode...it's just not happening. Damn thing is TOTALLY unresponsive...no power up, no charging icon...no lights...I mean nothing...no matter what I have tried, unless there is some new way I am unaware of. I even contemplated the "Unbrickable Mod" but that seemed more trouble than its worth, plus I don't have small enough tips for my iron...any ideas?
Yeah i black screened one about 4 monthes ago, and I could tell it was getting hinky. Keep working odin, sometimes you can get the yellow recognition to blink on.
Are you saying that Odin may pick it up even if the phone doesn't show DL mode?
Yes, if odin shows the yellow comfirmation com port, Ive heard odin will run it.
Wow...never heard of that, but I will definately keep trying and see if will pop up...thanks
Yeah if it goes into screens like upload mode, or anything try to connect it and see if Odin notices the phone. If it does, you're good.
I think you may need a JIG
Sent from my SGH-T959 using xda premium
If the phone doesn't power on, there is absolutely no hope of a software fix (odin/adb/etc), common sense.
Your only possible solution is sending it into JTAG, but if they can't fix it, they'll still usually charge you a procesing fee + shipping. Unbrickable Mod merely switches the boot order (so you can force it into dl mode with a jig), it won't magically bring a dead phone back to life. Then again you have nothing to lose trying if it's dead to begin with.
I'm willing to buy it off you for spare parts if you want as well.
j tag service is the way to go....
Sent from my GT-N7000 using xda premium

Telus Fascinate Brick

-----------------
---This first post is outdated. My current question is one post below. I've left the content of this post for other noobs to see.
-----------------
Hey folks, sorry to bother you all but all input would be greatly appreciated. I'm rather unfamiliar with android flashing and kernels, and have spent the last 8 hours trying to figure this out to no avail.
Following this (http://forum.xda-developers.com/showthread.php?t=1238070) (section 5) guide on how to get back to stock gingerbread on my phone (after a few partially failed attempts flashing other roms), I was using Odin, had the .pit 2.2 as well as CI500_VZW_EH03_GB_CM.tar.md5 loaded into the program and left it running. About 20 mins in, the phone stopped progressing and I started to get concerned. After two hours, I powered down the phone and proceeded to reattempt the flash. This is when things got weird. My phone was unable to enter the Download Mode and instead showed Android system recovery when plugged in, or a black screen with a phone and a computer, with arrows between when not plugged in. The weirdest part is that the phone no longer recognized vol+ or the power button when in Android Recovery, and could only vol- to go down the menu, then was stuck at the bottom of the list.
I've searched everywhere on this site, and google to try and come up with a solution.
When pluggin into the computer, I hear a connection sound, but the device is not recognized by Odin. Pressing the running a blind vol+ and vol-, then a vol- to hope Odin recognizes the device, as pointed out in this (http://forum.xda-developers.com/showthread.php?t=1764022) thread, resulted in nothing. Holding vol- while pluggin in the usb cable, doesn't show the download mode. All of the steps in this (http://forum.xda-developers.com/showthread.php?t=1026746) thread proved futile, as most of them required download mode anyways.
I'm going to keep searching and keep you posted as things come. Your help as always will be greatly appreciated!
Edit: Things just got weirder... After a few more attempts at making this work, I'm now getting an "Unable to charge non-supported battery. See user manual." With this error, I'm not able to get into Android Recovery anymore. More searching...
Edit 2: AFAIK I'm gonna need a jig. Anyone confirm?
Edit 3: Got a jig, Download Mode working, all is well. Please remove this thread, or leave it for other noob flashers to see.
Hey Folks, its been a while since I last posted in this forum, but I ran into a pretty serious issue earlier this evening. I was attempting to flash CM9 to my T959D and was running into tonnes of trouble. Throughout my attempts I was restoring back to stock rom, kernel and bootloader. During one of these restores, Odin froze in Win 7. Since then I've been unable to detect any form of life from the phone. It simply sits in a black screen. Holding the vol down while booting, blind vol up and down cable inserting, using my Jig and inserting the cable/battery in various orders results in nothing. The most I hear is a device failure to connect sound in Windows with no sign of life in Odin.
What can I do?
Someone posted stating leaving the battery out for multiple days would reset something on the motherboard, allowing me to get into download mode. Though I was hoping to have this resolved tonight. I realize that there aren't many people left with these phones, but I hope someone has a solution to this.
I'm going to be installing ubuntu tonight on an older desktop in a effort to resolve this. Though my experience with it is very limited, and success is unknown.
NOT GOOD... You should wait and see if others have a better solution, but Unbrickable Mod may be your only option.
Posted from my Fascinate using XDA Premium
MultipleMonomials said:
NOT GOOD... You should wait and see if others have a better solution, but Unbrickable Mod may be your only option.
Posted from my Fascinate using XDA Premium
Click to expand...
Click to collapse
Thats not good to hear. Well, I was snooping around looking for someone who could solder this for me, to no avail. My soldering skills are non existent. The most I fixed was a door bell, and I did a terrible job. I won't be able to get my hands on a soldering iron until tomorrow, is it worth trying?
I have located someone who can do a jtag on this model but have a few questions in regards to this:
Since my bootloader was corrupted, would the jtag service put a new bootloader on?
Would it prevent the same thing from happening again?
Are jtags designed on a per-phone basis?
Since there is a telus fascinate T959D as well as a verizon fascinate, and both phones are completely different, would I need to make sure the jtag is meant for this phone?
Is there anything I need to be made aware of before doing this that I haven't mentioned?
I've haven't had any experience with JTAG, but I've heard Unbrickable Mod is preferable. If you're looking for someone who can solder, check out your local RC/hobby store. If that fails, check out an electronics store, though it may take some searching to find one.
Posted from my Galaxy Tab with CM10
TheMegosh said:
Thats not good to hear. Well, I was snooping around looking for someone who could solder this for me, to no avail. My soldering skills are non existent. The most I fixed was a door bell, and I did a terrible job. I won't be able to get my hands on a soldering iron until tomorrow, is it worth trying?
I have located someone who can do a jtag on this model but have a few questions in regards to this:
Since my bootloader was corrupted, would the jtag service put a new bootloader on?
Would it prevent the same thing from happening again?
Are jtags designed on a per-phone basis?
Since there is a telus fascinate T959D as well as a verizon fascinate, and both phones are completely different, would I need to make sure the jtag is meant for this phone?
Is there anything I need to be made aware of before doing this that I haven't mentioned?
Click to expand...
Click to collapse
Make sure you use the stock Samsung cable see if you can reinstall the drivers hook it into the computer and hold volume down if you can get any type of signal from the phone your good.
Sent from my SCH-I500 using Tapatalk 2
---------- Post added at 04:27 PM ---------- Previous post was at 04:24 PM ----------
MultipleMonomials said:
I've haven't had any experience with JTAG, but I've heard Unbrickable Mod is preferable. If you're looking for someone who can solder, check out your local RC/hobby store. If that fails, check out an electronics store, though it may take some searching to find one.
Posted from my Galaxy Tab with CM10
Click to expand...
Click to collapse
Hey no offence but stop telling everyone on the street they need too soljeir there phone with unbrickable mod before they can fix I'm tired of having too calm the person down after you said they have too open up the phone its utter bull****. 1 out of 10 soft bricks you may need it I've been without download mode and fixed mine just fine.
Sent from my SCH-I500 using Tapatalk 2
An update:
Took my phone in to get the jtag service... He said some of my partitions were corrupted, one of which was the boot layer. He put a new bootloader on, and showed it could be placed back into recovery and download mode, but when I got home the device was even more dead than when I left; no device failed to connect sound in windows, just nothing. I'm taking it back to him in a week after exams to get this resolved. Maybe the battery has reached the end of its life...? I checked it with a volt meter, and it had 3v+ so I really don't know.
Sent using Science!
As bbrad pointed out, there may be other solutions, and my answer could be totally wrong, but if even your bootloader is cooked, Unbrickable Mod may be your only hope. Since UM affects startup code literally hardwired into the chip, it should work as long as the JTAG doesn't interfere.
Posted from my Fascinate using XDA Premium
Another update. So apparently I flashed a bootloader from another phone, which royally screwed up the partition, kernel and mounted drives. The technician managed to get the original bootloader, kernel and rom on the phone and everything is working from stock again.
Why on earth is the 959d Telus version such a pain in the ass to customize?
Is there anyone on here that uses a 959d that can direct me to a proper method to leaving stock? Before this entire situation I had vodoo kernel on, with cwm, but every time I flashed a kernel it would hang on reboot and either sit on a black or white screen. In a lot of cases I would flash in cwm, reboot, then I would be brought back to cwm as if there was no rom on the phone at all, no matter what I formatted and wiped.
When I'm not on my phone I can link all of the guides I've tried that leave me back where I started. So I re flash back to stock using Odin.
At the end of the day, I have to ask, is it really worth it in the end? I've rooted and flashed many roms on other phones but have never run into as many problems as with this fascinate t959d
Sent using Science!

[REQ] Odin Stock 4.1.2 Kernel!

So, I decided to stick with stock and what do I get? A phone that randomly stops working like I flashed a custom rom on it :X
All jokes and the sad situation aside, when plugged in i can get the Download Mode to stay open (else it closes after 3sec when not plugged in), figured I would try and flash the Stock Kernel to try and recover some of my app data but can only get to download mode so cant use recovery!
Can someone throw together an Odin flash-able Stock 4.1.2 Galaxy Note i717 Kernel together for me? Id like to try that before I outright flash over the entire rom through Odin!
Thanks!
Hammerfest said:
So, I decided to stick with stock and what do I get? A phone that randomly stops working like I flashed a custom rom on it :X
All jokes and the sad situation aside, when plugged in i can get the Download Mode to stay open (else it closes after 3sec when not plugged in), figured I would try and flash the Stock Kernel to try and recover some of my app data but can only get to download mode so cant use recovery!
Can someone throw together an Odin flash-able Stock 4.1.2 Galaxy Note i717 Kernel together for me? Id like to try that before I outright flash over the entire rom through Odin!
Thanks!
Click to expand...
Click to collapse
ok, I read that you have seemingly more than ample experience here o XDA, so I want to give you the respect that is due, however you post is a wee bit confusing. maybe that's due to a lack of some other information.
let me ask a few questions.
is this phone new to you?
can you get to about phone info? what does it say?
I don't understand you download mode information..........
if you were trying t flash stock kernel, then your not on stock?
if you are on stock, then you HAVE stock kernel?
what recovery are you supposed to have?
no offense meant, but you HAVE pressed VOL UP & DOWN and POWER until vibe and logo then releasing POWER for download mode right?
again no offense, but sometimes the simplest things right.......
captemo said:
ok, I read that you have seemingly more than ample experience here o XDA, so I want to give you the respect that is due, however you post is a wee bit confusing. maybe that's due to a lack of some other information.
let me ask a few questions.
is this phone new to you?
can you get to about phone info? what does it say?
I don't understand you download mode information..........
if you were trying t flash stock kernel, then your not on stock?
if you are on stock, then you HAVE stock kernel?
what recovery are you supposed to have?
no offense meant, but you HAVE pressed VOL UP & DOWN and POWER until vibe and logo then releasing POWER for download mode right?
again no offense, but sometimes the simplest things right.......
Click to expand...
Click to collapse
None taken been around the block a few times...
As for the phone, its basically in need of replacement by my thoughts, but I wanted to try and salvage some of my app data files:
WITHOUT the power plugged in, the unit does nothing but vibrate when I press the VOL Down, and any other key combos do not make the unit respond either.
When I remove the battery, then hold the VOL Down button... down... then put the battery back in, the unit will start in "Download mode" but even if I leave it on the screen or hit the up arrow to continue, after a few seconds it just shuts off and wont stay on.
However when I remove the battery, then hold the VOL Down, then plug in the adapter, it boots into download mode and doesnt shut off after a few moment's (however it wont start normally when I plug it in, just eternally vibrate).
The unit is an AT&T Variant of the Samsung Galaxy Note, specifically just the SGH-i717
The unit was/is running STOCK ROM+Kernel
I was making the request for the Stock Kernel for an Odin flash because when I had the Stock 4.0.4 I had a very identical situation occur (the difference being back then I could get and stay in download mode without using the power adapter) and used the Stock Odin Kernel from here:
http://forum.xda-developers.com/showthread.php?t=1506330
To get back into the unit and continue on without issue.
So the core of my post remains the same I need an Odin flash-able Stock AT&T 4.1.2 i717 kernel
*Your right, been here a while, I have tried again and again to grasp doing my own builds and all that other stuff when it comes to development and "do it yourself" and while I can fix a computer, build one, troubleshoot one, when it comes to Code... I am SO lost without a cause its not funny, so making the kernel file for myself is like asking me to walk on water when I am perfectly able to swim laps around someone who is ...
Sounds like you more than likely have a bad battery or a stuck power button. Mine had stuck on two separate occasions and just sits there vibrating and can't get it to boot or anything. Since I'm pretty sure you are out of warranty you can take a small screw driver and guitar pick to take it apart and use a little rubbing alcohol to clean the button.
Sent from my SAMSUNG-SGH-I717 using XDA Premium 4 mobile app
kind of with RQUIETT............
after reading more detailed post, the first thing that came to my head was the stuck power button issue which has plagued many.
the battery, I have seen many have that too.
I am definitely not he brainpan to just whip up a kernel like it were a batch of cookies or something, I am still just curious as to why you keep going on about just the kernel, but to each there own.
good luck and keep us posted
captemo said:
kind of with RQUIETT............
after reading more detailed post, the first thing that came to my head was the stuck power button issue which has plagued many.
the battery, I have seen many have that too.
I am definitely not he brainpan to just whip up a kernel like it were a batch of cookies or something, I am still just curious as to why you keep going on about just the kernel, but to each there own.
good luck and keep us posted
Click to expand...
Click to collapse
if you are still curious then you failed to read my last post... reading not required I guess
Ill check the power button, but it definitely doesn't feel stuck, gives the wonderfully audible click still (been in an otterbox the whole time), I also had the local AT&T store order me a replacement battery, if not Insurance claim it will be.
Random thought, the thing that doesnt add up is that if its a stuck power button, then it would STILL turn off when plugged in to the AC/PC, which it doesnt... but Im willing to give it a try because If fear they will try and replace my wonderful 16:10 screen with a ****ty 16:9 one... (sorry, for all the wow of the GN2, its to NARROW for my use)
Hammerfest said:
if you are still curious then you failed to read my last post... reading not required I guess
Click to expand...
Click to collapse
if anyone reads around here it is me, and I think its ok for me not to understand what needing a kernel alone is going to do for you. you came cross to me as a little harsh at someone who is trying to help and little demanding to expect someone to drop what they are doing just whip up a file for you flash in Odin.
I never claim to know everything here, and again, many times what I have to say (right or wrong) will spark someone else to chime in with a more educated answer.
but hey glad to try and help you anyway
My power button never felt stuck when it was. It did a lot of what you described when it did. Sometimes you can take it out of the case and tap on the back and it will free it up
Sent from my SAMSUNG-SGH-I717 using XDA Premium 4 mobile app
captemo said:
if anyone reads around here it is me, and I think its ok for me not to understand what needing a kernel alone is going to do for you. you came cross to me as a little harsh at someone who is trying to help and little demanding to expect someone to drop what they are doing just whip up a file for you flash in Odin.
I never claim to know everything here, and again, many times what I have to say (right or wrong) will spark someone else to chime in with a more educated answer.
but hey glad to try and help you anyway
Click to expand...
Click to collapse
Ill go ahead and post again what I posted before (again):
"""The unit is an AT&T Variant of the Samsung Galaxy Note, specifically just the SGH-i717
The unit was/is running STOCK ROM+Kernel
I was making the request for the Stock Kernel for an Odin flash because when I had the Stock 4.0.4 I had a very identical situation occur (the difference being back then I could get and stay in download mode without using the power adapter) and used the Stock Odin Kernel from here:
http://forum.xda-developers.com/show....php?t=1506330
To get back into the unit and continue on without issue."""
I have also made bold and increased the size of the "confusing" subject matter answer for you.
Also pretty sure I never asked anyone to drop what they where doing either.
@rquiett: thanks, I will go ahead and try and disassemble it and see if thats the case, they wont be processing any claims requests until Tuesday anyway, weird stuff as its the first time I have left the Phone Stock since FJ's rom's.(the irony of a phone having an issue while on stock when I normally flash everything with a custom rom does NOT escape me)
your welcome
I blame Samsung then since you are on stock
Sent from my SAMSUNG-SGH-I717 using XDA Premium 4 mobile app

[Q] Samsung Galaxy S Vibrant SGH-T959 stuck at PC-exclamationMark-MobilePhone icon

Alright. let us get this straight. I have searched in countless number of forums for solving my issue but I'm NOT able to fix it.
I have a Samsung Galaxy S Vibrant T959. It currently seems to be "soft-bricked" (I always see a mobile connected to a computer and an exclamation icon in between). So to reset it, I have left almost not stone unturned. But no luck so far
As far as I remember, I happened to land it in trouble while I was trying to flash some secondary bootloader using ODIN.
I also tried the micro-USB JIG method by building a 300k-Ohm USB JIG on my own (using three 100k-Ohm resistors), but even that is not working for me. Whenever I connect my phone to my computer, it starts up and shows those three icons. The same happens when I remove the battery, insert it back and start the phone up again. The same happens for each of the numerous key sequences mentioned online for download/recovery mode. So literally NOTHING is working for me. I also tried OneClick.jar, Heimdall. None of them are making me lucky as the phone is not getting detected.
I believe there has to be a way to reset it somehow (although I seem to have screwed something seriously) but nothing seems to work for me. What can I possibly do now?
Attached images show the micro-USB jig that I made and the icon on my phone I see.
From my experience if you can get that far you don't need a jtag. But you did say that you flash bootloader. So you ether need to get the right combo to get to download mode or you are done with out working bootloader. The only other thing that I can think of would be to do the unbrickable mod.
Sent from my Nexus 4
Thanks jrongi1 for the reply.
>> So you ether need to get the right combo to get to download mode or you are done with out working bootloader.
I have tried many, many combos for getting the download mode but no luck so far Can you suggest some if you are aware of one?
The only other thing that I can think of would be to do the unbrickable mod.
>> I tried to know about this but I did not understand what this exactly means? I believe this involves some sort of hardware rework. Can you please point me to steps to do this? Are you referring to this procedure? If yes, I don't believe it's a solution since that procedure is just a preventive measure and not a solution (that's what I understand after reading that whole thing out).
Try that.
reboot computer, turn off phone, take out battery, put the battery back, hold volume up and down buttons and then plug in usb.
Sent from my SGH-T959 using xda app-developers app
This is from N00B_IN_N33D's MIUI guide stickied at the top.
"SOFT" BRICKED WHILE USING ODIN?
If you are getting a "Phone.. ! ..Computer" image (seen above) when booting phone, yes, you are bricked but it is reversible! Just follow these steps...
Make sure you have ODIN OPEN with admin privileges!
1.) Take off your back cover, remove your sim & mirco sd card.
2.) Remove your battery.
Make sure you have the USB plugged into your PC but NOT your phone!
3.) Hold the volume buttons.
4.) Put the battery in.
5.) Put the USB in.
You don't necessarily need the download mode image to be present. As long as you are getting the COM ID to light up yellow in ODIN, just flash back to stock like normal.
Click to expand...
Click to collapse
Sometimes the key combo can be a bit precarious and the timing needs to be precise. I know that when I have taken my Vibes back to stock, it takes me more than a few tries to get it right. You've said you have tried the key combos several time, I think you should keep trying them and get your timing right. I would hate for you to screw up your phone when doing the Unbrickable hardware mod, when it could be something as simple as a timing thing.
As the other guys said work with the buttons and only try the unbrickable mod as a last resort.
Sent from my Nexus 4
Thanks guys for responses.
testomat/Woody, I tried as per your steps almost 8-10 times, but that does not work either
jrongi1,
I do not wish to go for Unbrickable mod either. Anyway, I have contacted a local repairs guy for this issue. He said he can fix this issue using JTAG interface. That costs me 1500INR. That's the only solution I have I guess.
Good luck with the repair I hope that you can get going soon.
Sent from my Nexus 4
Thank you so much again!
Woody said:
This is from N00B_IN_N33D's MIUI guide stickied at the top.
Sometimes the key combo can be a bit precarious and the timing needs to be precise. I know that when I have taken my Vibes back to stock, it takes me more than a few tries to get it right. You've said you have tried the key combos several time, I think you should keep trying them and get your timing right. I would hate for you to screw up your phone when doing the Unbrickable hardware mod, when it could be something as simple as a timing thing.
Click to expand...
Click to collapse
This worked for me.....Many thanks

Categories

Resources