im running the extreme1.92x kernel oc'd at 1.4 but not sure about the best setup to save battery. i made one profile for charging i put in on max. not sure what to do with the advanced tab settings.
Profiles are really dependent on the user and their needs. The one piece of advice I can give you is to make sure you have a profile set up in case your phone starts to over heat. An OC'ed phone maxed during a charge may get quite toasty.
any suggestions?
Imo dont o/c. Let the kernel operate the way it is setup. O/c cause reboots, phone heating up, and freezes.
Sent from my ADR6400L using XDA App
I'm running Adrynalyne's 4.4.7 kernel and use the following and get really good battery life with no overheating and no lag. I don't do a screen of profile because the governor seems to handle that pretty well.
Normal 1024 max 245 min-Smartass governor
Profiles:
Battery < 25% 768 max 245 min-On demand Governor
Charging 1280 Max 245 min-Smartass governor
itsDollar said:
Profiles:
Battery < 25% 768 max 245 min-On demand Governor
Charging 1280 Max 245 min-Smartass governor
Click to expand...
Click to collapse
Does that actually work?
I thought you had to choose a default governor and setup profiles accordingly.
I didn't know you could setup profiles with a governor that wasn't active or chosen on boot.
the thunderbolt is so fast already theres really no need to over clock. i left it at stock for normal, toned down to 768 when <30% battery and down to 368 when screen off. its a little slow for about half a second when waking up but the battery life is amazing. i can make it through a whole day without charging with moderate use. also running ziggys bfs kernel on virusrom and that added a ton of speed. way better than overclocking that drains your battery
im not asking about overclocking or profiles, just want to know about advanced settings. everything is set to default -1.
qman66 said:
im running the extreme1.92x kernel oc'd at 1.4 but not sure about the best setup to save battery. i made one profile for charging i put in on max. not sure what to do with the advanced tab settings.
Click to expand...
Click to collapse
What Rom are you using?
Go to settings, menu, wireless networks, mobile networks and uncheck the third box. No need to have mobile data always on for most peeps . You'll still have 4G n everything, but gain a good 1-2 maybe more hrs (depending on use, kernels, governor settings, and I/O scheduling. I personally am running BAMF 1.6.2 with adryns 4.4.7 kernel, no set CPU, using tool box for that at 245mhz min - 1.024GHz max with ondemand governor and most importantly SIO Scheduler. Try these n you will have amazing performance and better battery life. Let me know you opinions
Sent from my ADR6400L using XDA Premium App
No matter how precise I click, I can't get SetCPU to set 1024mhz. Closest I can get is 1036. What gives? lol
sprodigy said:
No matter how precise I click, I can't get SetCPU to set 1024mhz. Closest I can get is 1036. What gives? lol
Click to expand...
Click to collapse
Haha, I couldn't tell if you were being serious or not but each kernel has speeds at different increments. 1036 will probably be as close as you can get to 1024.
dopediculous said:
What Rom are you using?
I personally am running BAMF 1.6.2 with adryns 4.4.7 kernel, no set CPU, using tool box for that at 245mhz min - 1.024GHz max with ondemand governor and most importantly SIO Scheduler. Try these n you will have amazing performance and better battery life. Let me know you opinions
Sent from my ADR6400L using XDA Premium App
Click to expand...
Click to collapse
My settings are identical except running 1.6.3, what does the SIO scheduler do or any of the schedulers for that matter?
mrsmith35sg said:
My settings are identical except running 1.6.3, what does the SIO scheduler do or any of the schedulers for that matter?
Click to expand...
Click to collapse
You can use Wikipedia for the scheduler info. Once you look into it you'll know why I didn't wanna type all those details in here from my phone. Lol, but yeah set that to SIO, Take off ENABLE data always on. N you should be better let me know.
Sent from my ADR6400L using XDA Premium App
rdompor said:
Haha, I couldn't tell if you were being serious or not but each kernel has speeds at different increments. 1036 will probably be as close as you can get to 1024.
Click to expand...
Click to collapse
Go to manage applications and clear data from set CPU and when u go back in to set CPU you will have to hit auto detect n if ur kernel has that frequency you'll be able to click it.
Sent from my ADR6400L using XDA Premium App
Related
So, I was wondering which would be the better to run on an OC kernal, SetCpu or Voltage Control. I'm using SetCpu (cause I paid for it lol) but notice that a lot of people talk about using Voltage Control instead of the later. Is this due to options, or is it simply because it's free? Any help is appreciated, and anybody that gives me a non-flaming serious response will get a thanks lol!
Running:
Trigger v2.7.2
Tigersblood v2 OC Kernal
(all statistics may change without notice lol!)
TXLunchbox said:
So, I was wondering which would be the better to run on an OC kernal, SetCpu or Voltage Control. I'm using SetCpu (cause I paid for it lol) but notice that a lot of people talk about using Voltage Control instead of the later. Is this due to options, or is it simply because it's free? Any help is appreciated, and anybody that gives me a non-flaming serious response will get a thanks lol!
Running:
Trigger v2.7.2
Tigersblood v2 OC Kernal
(all statistics may change without notice lol!)
Click to expand...
Click to collapse
I just installed Voltage Control 1 hour ago. So far I like it better than SetCpu which I also paid for it. Voltage Control has options to lower the votage in various steps. The voltages can be lowered without needing to overclock the CPU.
Installed it after installing Tigers Blood V2 kernel. But now I want to see how my battery life is undervolted and not overclocked.
I prefer voltage control but I also have the paid set cpu from before when I didn't know about voltage. Voltage let's you uv (undervolt) your frequencies to conserve some battery life.
Trigger + Tigerblood = Winning
Well it just depends on what your trying to do, in example, if you want to set profiles and Oc, I would use Setcpu, if your trying to undervolt your clock speed, and have Oc, I would use Voltage Control. I use both because I'm trying to Overclock, and have lower voltages
Wow guys! Thanks so much! This is really helpful info.
Bambam, what settings are you using with Tigers blood and Trigger?
Sent from my SGH-T959 using XDA Premium App
TXLunchbox said:
Wow guys! Thanks so much! This is really helpful info.
Bambam, what settings are you using with Tigers blood and Trigger?
Sent from my SGH-T959 using XDA Premium App
Click to expand...
Click to collapse
My settings, this might not work for your phone, every phone is different. Battery life seems great so far.
100mhz -50 = 900mv
200mhz -50 = 900mv
400mhz -50 = 1000mv
800mhz -50 = 1150mv
1000mhz -50 = 1225mv
1200mhz -25 = 1275mv
Good luck.
I personally use SetCpu for OC because i've been using it since the Nexus One and i think its just the better app b/c of ease of use
Again guys (or gals), I really appreciate all the feedback. Thanks have been given appropriately as promised. Sorry about the delay. This has been the first day that I could get to my laptop lol!
One thing I have noticed is that when SetCpu is set to "performance" the phone has difficulty pulling up the multi-tasker when long pressing the home button. This is how I get to Task Manager to clear things up before running benchmarks, so it's somewhat of a big deal to me. I'm sure there are other ways around it. I know on the stock OS that there is a Task Manager widget, but that has seemed to have disappeared with the ROMs that I've ran.
GTOJim said:
My settings, this might not work for your phone, every phone is different. Battery life seems great so far.
100mhz -50 = 900mv
200mhz -50 = 900mv
400mhz -50 = 1000mv
800mhz -50 = 1150mv
1000mhz -50 = 1225mv
1200mhz -25 = 1275mv
Good luck.
Click to expand...
Click to collapse
Thanks for the info Jim, I'm really trying out different UV settings. I'm running just the standard right now cause other settings I've tried have caused me the SOD lol!
I don't know if this applies anymore but TW used to suggest the following setting when using SetCPU.
Conservative, do not set on boot-up. Minimum clock speed of 200mhz. Some phones would not wake up using the default of 100mz minimum. As I remember they advised against setting up any profiles.
Yeah, I've known about the no profiles thing. I think I've stuck to using Voltage Control as I haven't had nearly as much issues with it.
The latest jt kernels and people's derivatives of them have not been playing well with SetCPU on my phone. It has been freezing up. Any advice on a certain version I should use or maybe settings issue?
Check to make sure profiles is not enabled. Using them will make your phone freeze and or not come back awake.
Also make sure your on conservative and not ondemand. I hear the ondemand is still being a little buggy.
Currently I'm running jt's oc kernel at 1.3ghz stable. Setcpu is on conservative and I have zero problems, only when I change to another setting does it have problems.
At this time what could I use setcpu for besides overclocking?
theres no point in using setcpu with jts kernels as theyre not overclocked...unless u need to UNDERclock for some reason
tonu42 said:
Check to make sure profiles is not enabled. Using them will make your phone freeze and or not come back awake.
Click to expand...
Click to collapse
I'm using setcpu to underclock my phone (for bettery battery life), and I set up a few profiles to drop the speed down when the screen is off (100 min, 200 max), and when the battery is below a certain amount (100 min, 400 max), and it seems to be running fine. No freezes, no problem waking up.
gkirby11 said:
Also make sure your on conservative and not ondemand. I hear the ondemand is still being a little buggy.
Currently I'm running jt's oc kernel at 1.3ghz stable. Setcpu is on conservative and I have zero problems, only when I change to another setting does it have problems.
Click to expand...
Click to collapse
JT doesn't have an OC kernel out. If you're using nemesis's OTB OC kernel then you shouldn't be using SetCPU, you should be using Voltage Control from market. SetCPU has caused some issues. This will give you orange CWM but you can always Odin the red one.
Undervolting and profiles.
I have tried a crap ton of different undervolting setting, but none work
Also the profiles in set cpu don't seem to work for me. I have a few of them set and it always sits on the top one I need some guidence with both please!
Another thing my xda premium app isn't pushing my notafications yes its set
Sent from my MB860 using xda premium
Undervolting is a delicate process. It takes time to find the max undervolt that is stable. With that being said, try undervolting everything by the lowest amount which is -25mv. Check to see if that is stable. If so proceed to go further. Remember lower freq will typically undervolt farther than higher frequencies.
As far as profiles go your probably not using the priority values right. The higher priority is what determines which profile setcpu uses. So for instance if you want a safeguard against overheating, you could set the profile for when the cpu goes above 55C to throttle the processor way down. If you set this profile to 100(max) it will overide all other profiles at 98, 99, 75, 50...etc. Also this may be obvious to some but be sure to tick(enable) the profiles button. If thats not ticked then it doesnt matter how many profiles you have set up. It simply wont use them.
jack_slapped said:
Undervolting is a delicate process. It takes time to find the max undervolt that is stable. With that being said, try undervolting everything by the lowest amount which is -25mv. Check to see if that is stable. If so proceed to go further. Remember lower freq will typically undervolt farther than higher frequencies.
As far as profiles go your probably not using the priority values right. The higher priority is what determines which profile setcpu uses. So for instance if you want a safeguard against overheating, you could set the profile for when the cpu goes above 55C to throttle the processor way down. If you set this profile to 100(max) it will overide all other profiles at 98, 99, 75, 50...etc. Also this may be obvious to some but be sure to tick(enable) the profiles button. If thats not ticked then it doesnt matter how many profiles you have set up. It simply wont use them.
Click to expand...
Click to collapse
When I was on alien rom, I tried 25 on all and it restarted after like a minute. What worked for me was 25 25,50,50,75,75,100 fromm bottom to top. I tried it with cm7 and total no go lol
Lemme tryi 25 on all and see what I get and I didn't know that. They all werent working, so I set them all to 100 lmao, I understand that now
Sent from my MB860 using xda premium
Aparently its been running 125,125,50,75,75,75,75bottom to top cm7 with 1.3 kernel.
It did restart a couple min ago randomly. Will keep posted
Sent from my MB860 using xda premium
Glad your getting some results. If it restarts even once it means at least one of your undervolted freq isn't stable. With your settings I would wager its in the uper freq considering your undervolt in the lower freq isn't too extreme. You might try decreasing the undervolt for your upper freq to -50 -50 -50 starting at the top. Might help to stabilize bc higher freq just require more voltage. If that proves to be stable continue trying to reduce the lower freq as much as possible. Mainly bc if you set your profiles right(screen off is the most important really) your phone will spend the majority of its time on the 200mhz freq. Thus the more undervolt on that freq should theoretically give the most benefit from undervolting. This is just all from personal experience. I'm no guru. Just spent way too much time adjusting voltages on phones . And of course having the upper freq undervolted as much as possible cant hurt either.
jack_slapped said:
Glad your getting some results. If it restarts even once it means at least one of your undervolted freq isn't stable. With your settings I would wager its in the uper freq considering your undervolt in the lower freq isn't too extreme. You might try decreasing the undervolt for your upper freq to -50 -50 -50 starting at the top. Might help to stabilize bc higher freq just require more voltage. If that proves to be stable continue trying to reduce the lower freq as much as possible. Mainly bc if you set your profiles right(screen off is the most important really) your phone will spend the majority of its time on the 200mhz freq. Thus the more undervolt on that freq should theoretically give the most benefit from undervolting. This is just all from personal experience. I'm no guru. Just spent way too much time adjusting voltages on phones . And of course having the upper freq undervolted as much as possible cant hurt either.
Click to expand...
Click to collapse
25,50,50,50,50,75,75
Still getting a reboot:'(
Only good thing about the reboot is it turns on instantly
PROFILES CONFIRMED WORKING trying to indwrvolt this thing
I think I'm gonna order another battery too bc this one isn't getting the 16 hours it was, I cant say much bc I'm screwing with the settings hardcore xD I will show.all settings in a sec
Sent from my MB860 using xda premium
Sent from my MB860 using xda premium
Blahhh
Put blah there so it would post lol. Also going to download a stress test or quadrent thing to test the stress and find maximum uv
Sent from my MB860 using xda premium
Undervolting COMPLETE=D
QUAD SCORE! OCED 1.3 CM7
Right now I'm thinking my battery life is going to be amazig and if I turned the data off when not using it... omg I would last like 2 straight days prolly=D
So pumped to test everything morrow!!
Side note:800mhz or above wont go past 75 >:/
Had really important question to ask you but forgot
Also tried putting 215 to 275 that was a no go lol. My question was is there a battery manager and info like the stock one for cm7?!!!
Sent from my MB860 using xda premium
Smittyzz said:
Undervolting COMPLETE=D
QUAD SCORE! OCED 1.3 CM7
Right now I'm thinking my battery life is going to be amazig and if I turned the data off when not using it... omg I would last like 2 straight days prolly=D
So pumped to test everything morrow!!
Side note:800mhz or above wont go past 75 >:/
Had really important question to ask you but forgot
Also tried putting 215 to 275 that was a no go lol. My question was is there a battery manager and info like the stock one for cm7?!!!
Sent from my MB860 using xda premium
Click to expand...
Click to collapse
well my battery was draining mad quick so I am not overclocking It anymore unless I want to show off or play games lol, lost 20% in one hour. Now its stable and undervolted
Sent from my MB860 using xda premium
First off, regarding SetCpu and over / undercloking, dev has said it'll only underclock/overclock ONE core at a time. It's a bug and he's working on it from what I understand. If both cores are needed to be in use at the same time, no over / underclocking will be applied. Secondly, profiles work as they should in SetCpu, so that's a problem on your end. Third, the undervolting can't be more than 100mv differnce between jumps. See screen shot.
http://www.multiupload.com/YUK0KPXZLJ
Phalanx7621 said:
First off, regarding SetCpu and over / undercloking, dev has said it'll only underclock/overclock ONE core at a time. It's a bug and he's working on it from what I understand. If both cores are needed to be in use at the same time, no over / underclocking will be applied. Secondly, profiles work as they should in SetCpu, so that's a problem on your end. Third, the undervolting can't be more than 100mv differnce between jumps. See screen shot.
http://www.multiupload.com/YUK0KPXZLJ
Click to expand...
Click to collapse
I understand the 100 thing and I got the undervolting and profiles done. I hope he gets both cores supported soon and thank you dmfor the reply
Sent from my MB860 using xda premium
Yea Im skeptical about not setcpu not having support for dual cores... Did some searching on the net and couldnt find anything to support that. As far as not the tegra 2 not being able to do over 100mv jumps. That's not true. My lowest frequency is 600mv (-150) and my next frequency is at 750mv. That's a 150mv difference right there... And I'm completely stable. Its entirely dependent on your processor. They are all different and respond differently to undervolting. You just have to find what works for you. Generally though the lesser the jumps in voltage will give you more stability.
a good kernal helps too im useing faux123 v2.0 0C1.3 its undervolts quite well
us/alienv4UL/OC1.3{webtop2sd{fixed}
Hi, i have just flashed the new HyperDroid v5.2.21 (Full wipe) and i wanted to know if i can overclock my SGS2 from 1.2ghz to 1.5ghz, if so how do i go about it?
Do i need to change the current kernel (XWL1)?
P.S ive heard its stable, but does it drain the battery?
Thanks XDA Community
Hello there. Yep you can overclock but you need a kernel that supports it. [url="http://gokhanmoral.com]SiyahKernel[/url] is a good choice. With that, use the Voltage Control app from the market.
However I know nothing about battery draining or stability... dualcore 1.2GHz mobile processor is more than enough for me, and the phone can get pretty hot under maximum load, same with the MALI GPU which can be overclocked to 400MHz (but since it has 4 cores and the phone has no active heatsinks it could get risky...)
AJ.Rockwell said:
Hello there. Yep you can overclock but you need a kernel that supports it. [url="http://gokhanmoral.com]SiyahKernel[/url] is a good choice. With that, use the Voltage Control app from the market.
However I know nothing about battery draining or stability... dualcore 1.2GHz mobile processor is more than enough for me, and the phone can get pretty hot under maximum load, same with the MALI GPU which can be overclocked to 400MHz (but since it has 4 cores and the phone has no active heatsinks it could get risky...)
Click to expand...
Click to collapse
I think AndroidMeda kernel already supports OverClocking...using this ROM for a quite long time...
Harvinder09 said:
Hi, i have just flashed the new HyperDroid v5.2.21 (Full wipe) and i wanted to know if i can overclock my SGS2 from 1.2ghz to 1.5ghz, if so how do i go about it?
Do i need to change the current kernel (XWL1)?
P.S ive heard its stable, but does it drain the battery?
Thanks XDA Community
Click to expand...
Click to collapse
Yes you can overclock and you can stick with the kernel that comes with Hyperdroid. I am currently Overclocking 1.6ghz max and 200 min. Not touching voltages though. Use No-Frills app to set it up. My advice though to you no point in overclocking as 1.2ghz is good enough as it is..And the kernel you are on is good enough...It is stable depending what voltage frequencies you use..I say leave it as they are. And like i said download No-Frills from the market..Set your clock speeds and that should be it..Choose a governor and off you go
Neo3000 said:
Yes you can overclock and you can stick with the kernel that comes with Hyperdroid. I am currently Overclocking 1.6ghz max and 200 min. Not touching voltages though. Use No-Frills app to set it up. My advice though to you no point in overclocking as 1.2ghz is good enough as it is..And the kernel you are on is good enough...It is stable depending what voltage frequencies you use..I say leave it as they are. And like i said download No-Frills from the market..Set your clock speeds and that should be it..Choose a governor and off you go
Click to expand...
Click to collapse
No-Frills ? AndroidMeda Developers recommend Voltage Control (and I personally like it much more than No-Frills, too) with their kernel.
+ Here is a small guide : http://forum.xda-developers.com/showthread.php?t=1036020 how to test your OC Settings, I use it when I am testing new voltages.
Thanks for the replies i will try out the no-frills app and see what happens. What would you say is the best governor to use? and wouldnt you recommend going over 200min?
DomButcher said:
No-Frills ? AndroidMeda Developers recommend Voltage Control (and I personally like it much more than No-Frills, too) with their kernel.
+ Here is small guide : http://forum.xda-developers.com/showthread.php?t=1036020 how to test your OC Settings, I use it when I am testing new voltages.
Click to expand...
Click to collapse
Pongster uses No-Frills. The rest of the team uses Voltage Control. And to avoid any freezes or random reboots leave the voltage settings as they are till you get to grips with the overclocking. Hence why i suggested No-Frills as currently Voltage Control for me kept on reverting back to stock frequencies..And yes there is a way round it but it is to much of an effort
Harvinder09 said:
Thanks for the replies i will try out the no-frills app and see what happens. What would you say is the best governor to use? and wouldnt you recommend going over 200min?
Click to expand...
Click to collapse
I am currently using ondemand and Sio as scheduler. You can not go wrong with that. Like i said..choose a governor choose a scheduler and let them do the work...I also do recommend Voltage control but No-frills is simple and does the job for you. And no i would recommend either go to 100min or stick with 200...I am currently on 1.6max and 200 min
Harvinder09 said:
Thanks for the replies i will try out the no-frills app and see what happens. What would you say is the best governor to use? and wouldnt you recommend going over 200min?
Click to expand...
Click to collapse
I personally use Sleepy governor and noop scheduler, but everyone uses different governors and schedulers...
I think 200 min is OK...100 MHz is too low and 500 is too high...
Neo3000 said:
Pongster uses No-Frills. The rest of the team uses Voltage Control. And to avoid any freezes or random reboots leave the voltage settings as they are till you get to grips with the overclocking. Hence why i suggested No-Frills as currently Voltage Control for me kept on reverting back to stock frequencies..And yes there is a way round it but it is to much of an effort
Click to expand...
Click to collapse
I have -75mV (previously had -50mV) and I haven't ever had any freeze or random reboot...
DomButcher said:
I personally use Sleepy governor and noop scheduler, but everyone uses different governors and schedulers...
I think 200 min is OK...100 MHz is too low and 500 is too high...
I have -75mV (previously had -50mV) and I haven't ever had any freeze or random reboot...
Click to expand...
Click to collapse
Dude..he is just learning...let him take baby steps first before he jumps right up and wants to walk.... Let him follow what i suggested and then he can come back and ask for more help once he tries his new settings out...I remember you use to ask a lot of questions before..And i said the same thing..baby steps first before you start walking
Neo3000 said:
Dude..he is just learning...let him take baby steps first before he jumps right up and wants to walk.... Let him follow what i suggested and then he can come back and ask for more help once he tries his new settings out...I remember you use to ask a lot of questions before..And i said the same thing..baby steps first before you start walking
Click to expand...
Click to collapse
Oh...he has just 6 posts...I didn't notice it...sorry. Then I will suggest No-Frills, too.
DomButcher said:
Oh...he has just 6 posts...I didn't notice it...sorry. Then I will suggest No-Frills, too.
Click to expand...
Click to collapse
Good..Now thanks wont hurt
Thanks for the support guys, and yeah i am new to this whole android/rooting scene so no-frills looks like a nice simple and easy option for now until i get to grips with things. i will try out the differen governors and schedulers and see whats best for me.
P.S Neo is yours running stable at the maximum 1.6ghz?
Harvinder09 said:
Thanks for the support guys, and yeah i am new to this whole android/rooting scene so no-frills looks like a nice simple and easy option for now until i get to grips with things. i will try out the differen governors and schedulers and see whats best for me.
P.S Neo is yours running stable at the maximum 1.6ghz?
Click to expand...
Click to collapse
Yes my friend pretty stable. Listen go here http://forum.xda-developers.com/showthread.php?t=1369817 and read regarding governors and schedulers..Pretty straight forward and good explanations...And i am running the latest hyperdroid version but i am using Siyah kernel with thunderbolt tweaks...For you i would use the kernel that comes with the rom and use the default governor that comes with the rom...When i was on previous kernel version i always use to use Kenobi...Not sure if they have it there or if Pongs removed it but either that or solo...
Neo3000 said:
Yes my friend pretty stable. Listen go here http://forum.xda-developers.com/showthread.php?t=1369817 and read regarding governors and schedulers..Pretty straight forward and good explanations...And i am running the latest hyperdroid version but i am using Siyah kernel with thunderbolt tweaks...For you i would use the kernel that comes with the rom and use the default governor that comes with the rom...When i was on previous kernel version i always use to use Kenobi...Not sure if they have it there or if Pongs removed it but either that or solo...
Click to expand...
Click to collapse
Kenobi was removed and solo was renamed to sleepy.
which governer is best with overclocking 1.6ghz
mzeshanhakeem said:
which governer is best with overclocking 1.6ghz
Click to expand...
Click to collapse
i am using ondemand
Neo3000 said:
i am using ondemand
Click to expand...
Click to collapse
Neo when i overclock to 1.6ghz with 200min using the lulzactive governer and SIO scheduler my phone freezes i have to reboot it?
whats the best setup to run 1.6ghz so its stable for everyday use?
P.S anyone know if it drains the battery by overclocking?
Harvinder09 said:
Neo when i overclock to 1.6ghz with 200min using the lulzactive governer and SIO scheduler my phone freezes i have to reboot it?
whats the best setup to run 1.6ghz so its stable for everyday use?
P.S anyone know if it drains the battery by overclocking?
Click to expand...
Click to collapse
change to ondemand governor when overclocking
Neo3000 said:
change to ondemand governor when overclocking
Click to expand...
Click to collapse
And what scheduler?
Thanks
Harvinder09 said:
And what scheduler?
Thanks
Click to expand...
Click to collapse
stick with SIO
Some of you may recall my similar thread for SetCPU...
http://forum.xda-developers.com/showthread.php?t=1321136&page=8
Well I recently switched over from SetCPU to VC and am quite happy with it... figured I'd make a thread for users to share their experiences with the app...
First a few ground rules...
You must share the following info...
Kernel, Rom, Paid of Free version of the app, Screen on time, and all your settings in the fields in the app. Also include your average battery life on a full charge and if you're on the stock battery/charger or not. *Pics are encourages and appreciated.*
my config is in my sig...
I'm also using the paid version of VC which is awesome and I have undervolted quite a bit.
*The following voltages are being tested for stability*
Noop + Ondemand
100mhz-1200mhz
1200mhz: 1200 mV
1000mhz: 1050 mV
800mhz: 950 mV
500mhz: 850 mV
200mhz: 850 mV
100mhz: 825 mV
GPU 114-267mhz
114 @ 800
267 @ 950
I average about 24hrs - 26hrs of battery pending my use with about 3hrs of screen on time.
Purpose of this thread is to exchange information on how to get a better performing and more battery efficient phone using some tweaks.
P.S. Remember all phones are different and you should NEVER expect someone else's config to work for you. The purpose in this is to get a base line for tweaking and help out users with little or no knowledge about getting good battery life and also how to make their phone faster/more efficient.
Thanks
Nice to see a similar thread for the i777 model running Entropy's kernel as well. As I always say, caring is sharing lol
Crack on mate. This kind of info makes it so much easier for new users to get started with undervolting without having too many trial and error headaches.
If anyone wants to know my settings for Siyah and VC, then click the MagicConfig link in my sig.
Communicated using an SGS2 droid with XDA premium neurotransmitter while DJ'ing on the Enterprise.
geko95gek said:
Nice to see a similar thread for the i777 model running Entropy's kernel as well.
Crack on mate. This kind of info makes it so much easier for new users to get started with undervolting without having too many trial and error headaches.
If anyone wants to know my settings for Siyah and VC, then click the MagicConfig link in my sig.
Communicated using an SGS2 droid with XDA premium neurotransmitter while DJ'ing on the Enterprise.
Click to expand...
Click to collapse
Thanks for the support bud. Much appreciated.
vc-
1600mhz-1425mV
1400mhz-1275mV
1200mhz-1175mV
1000mhz-1075mV
800mhz-975mV
500mhz-875mV
200mhz-850mV
Lasts more than 24 hours almoust all the time.
Najuto9tail said:
vc-
1600mhz-1425mV
1400mhz-1275mV
1200mhz-1175mV
1000mhz-1075mV
800mhz-975mV
500mhz-875mV
200mhz-850mV
Lasts more than 24 hours almoust all the time.
Click to expand...
Click to collapse
great voltages... Thanks for sharing.
Is there anything you guys are doing to test each individual frequency? Or just setting it at that frequency?
Sent from my SGH-I777 using Tapatalk
K Rich said:
Is there anything you guys are doing to test each individual frequency? Or just setting it at that frequency?
Sent from my SGH-I777 using Tapatalk
Click to expand...
Click to collapse
Well personally I set a voltage then assign my min and Max to the frequency that corresponds to the newly set voltage and then run a benchmark to see if any issues occur.
Sent from my kick ass Galaxy S II
Alucardis666 said:
Well personally I set a voltage then assign my min and Max to the frequency that corresponds to the newly set voltage and then run a benchmark to see if any issues occur.
Sent from my kick ass Galaxy S II
Click to expand...
Click to collapse
Exactly what I've been doing. If anyone has any input, please do tell.
Cpu
200mhz-850mv
500mhz-875mv
800mhz-950mv
1000Mhz-1050mv
1200mhz-1150mv
Gpu
100Mhz-800mv
267Mhz-950mV
Not getting the battery life i would like, i still drop a few percent per hour when not doing anything, but im pretty sure thats because im on 2.3.6! ive been trying to do that gpu 3 step thing i keep hearing about via scripts but it seems to mess up my voltage settings!
anyway here they are! i cant wait to see what others have!
A question: Do you use both VC and SetCPU? Won't the governor setting in VC clash with the governor settings/advance settings and profiles set in SetCPU?
Fearing that, just today morning I switched to VC Lite from SetCPU (and froze SetCPU) as I wanted scheduler control.
VC Lite settings:
Scheduler: noop
Governor: conservative
Frequencies: 200-1000
Voltages:
1600 - 1400mV
1400 - 1250mV
1200 - 1200mV
1000 - 1100mV
800 - 1000mV
500 - 900mV
200 - 850mV
---------- Post added at 10:16 PM ---------- Previous post was at 10:13 PM ----------
Alucardis666 said:
Well personally I set a voltage then assign my min and Max to the frequency that corresponds to the newly set voltage and then run a benchmark to see if any issues occur.
Sent from my kick ass Galaxy S II
Click to expand...
Click to collapse
Do you simply run something like Antutu Benchmark? Or does VC Pro have stress testing?
K Rich said:
Exactly what I've been doing. If anyone has any input, please do tell.
Click to expand...
Click to collapse
You'll find that you can run lower voltage on a forced single stepping than you can when the CPU has several steppings to choose from. For some reason the CPUs don't play well if you go to low or if it has to make to big of a jump between certain steppings.
\/icious said:
You'll find that you can run lower voltage on a forced single stepping than you can when the CPU has several steppings to choose from. For some reason the CPUs don't play well if you go to low or if it has to make to big of a jump between certain steppings.
Click to expand...
Click to collapse
running Antutu to test each step?
jazzboyrules said:
A question: Do you use both VC and SetCPU? Won't the governor setting in VC clash with the governor settings/advance settings and profiles set in SetCPU?
Fearing that, just today morning I switched to VC Lite from SetCPU (and froze SetCPU) as I wanted scheduler control.
VC Lite settings:
Scheduler: noop
Governor: conservative
Frequencies: 200-1000
Voltages:
1600 - 1400mV
1400 - 1250mV
1200 - 1200mV
1000 - 1100mV
800 - 1000mV
500 - 900mV
200 - 850mV
---------- Post added at 10:16 PM ---------- Previous post was at 10:13 PM ----------
Do you simply run something like Antutu Benchmark? Or does VC Pro have stress testing?
Click to expand...
Click to collapse
I no longer use setcpu and I do run quadranrt or antutu usually. pro version has no such stress test, but if you ask me... one should be implemented in a future update.
What amazes me is the difference a rom can make. Running Siyah 2.6.11 with the exact same VC settings (the ones in the OP of this thread) on CM7 nightly and ShoStock 1.9.1 and running Quadrant the results are about 1000-1500 points higher on cm7 nightly. From a user feel perspective they are both smooth as butter but I wonder what makes CM7 so much faster on the synthetic benchmark. Has to be a storage I/O thing or something. Battery life seems to be better for me on ShoStock though.
kennonk said:
What amazes me is the difference a rom can make. Running Siyah 2.6.11 with the exact same VC settings (the ones in the OP of this thread) on CM7 nightly and ShoStock 1.9.1 and running Quadrant the results are about 1000-1500 points higher on cm7 nightly. From a user feel perspective they are both smooth as butter but I wonder what makes CM7 so much faster on the synthetic benchmark. Has to be a storage I/O thing or something. Battery life seems to be better for me on ShoStock though.
Click to expand...
Click to collapse
Yea, I too have noticed slight variations on different roms as well.
CM7 nightly 01/24/12
I/O Scheduler : SIO
Governor : ondemand
200Mhz-1200Mhz
1200Mhz : 1200mV
1000Mhz : 1100mV
800Mhz : 1000mV
500Mhz : 900mV
200Mhz : 875mV
Phone has been on for 6hr with 1hr 5mins screen on time and I'm sitting at 80%
Got 6520 in Antutu at 1200Mhz with this setup
K Rich said:
running Antutu to test each step?
Click to expand...
Click to collapse
I used to test steps individually but again what's stable individually might not be stable with all the other steps included. I usually will quickly run through apps like mms, email, video, web, and also run a few BMs like antutu
A useful app with all the bells and whistles, with the capabilities of almost every utility app available is ROM Toolbox. I use it to edit voltage, CPU frequency, build.props, etc. Look into it if you're tired of trying hundreds of different programs for different features.
Sent from my SAMSUNG-SGH-I777 using xda premium
geko95gek said:
Nice to see a similar thread for the i777 model running Entropy's kernel as well. As I always say, caring is sharing lol
Crack on mate. This kind of info makes it so much easier for new users to get started with undervolting without having too many trial and error headaches.
If anyone wants to know my settings for Siyah and VC, then click the MagicConfig link in my sig.
Communicated using an SGS2 droid with XDA premium neurotransmitter while DJ'ing on the Enterprise.
Click to expand...
Click to collapse
I've been using those settings with shostock rom and I have to say it has been working wonderfully
Sent from my SAMSUNG-SGH-I777 using xda premium
vc and set cpu
How do they get alone? Im afraid they might not like each other.