Related
Hello all.
While I was taking my HD2 apart to replace a cracked screen (glass digitizer) I accidentally broke the connector off one of the wires. The wire is black and a few inches long with a silver and round press on connector on each end. It attaches to the board that houses the vibrator motor and runs down the right side of the phone (if you were looking at it face down and partially disassembled).
Unfortunately, I lost the metal piece that broke off the wire (the thing is tiny!), so I can't just solder it back on. Any idea on where I can buy a replacement? I've spent about 6 hours today on ebay and google to no avail. Searching for "HD2 black wire" and anything similar is hardly efficient, but that's all I know about it.
Any help appreciated.
Thanks,
Chris
Good question, I think I damaged the cable to the volume buttons so it would be cool if someone has an adress where we can get spare parts except LCD and Digitizer..
this guy on ebay seems to be selling an HD2 in parts. you might find what you need here:
http://stores.ebay.co.uk/Right-Click-Enterprises/_i.html?_nkw=hd2&submit=Search&_sid=131407386
Thanks, I sent that guy a message and hopefully it'll work out.
Anyone else have a source?
connector of my hd2 is also broken HTC says that the mainboard must be change and I have to pay € 230 because that is my responsibility
I think you have damaged your coaxial cable connector for wifi and bluetooth. Google will help you perhaps.
I believe that my wifi/bluetooth cable is broken, as I have no wifi or bluetooth signal since dropping my phone as reported in a previous post of mine. Can anybody advise me on the difficulty of undertaking this repair myself, does it involve complete disassembly of phone, any soldering etc. If this is the case I don't feel confident enough to do this so does anybody know of someone who does this sort of repair, I have found the cable on e bay for £7 and it looks like it has push on connectors ?
if the connectors on the boards are not broken then all you need is the coaxial cable with connectors on the two end. you need not disassemble the whole set, just open the back cover, connect one end of the cable to mother board and other end to the rigid flex board and that's it.
WiFi and Bluetooth not working
raincybercafe said:
if the connectors on the boards are not broken then all you need is the coaxial cable with connectors on the two end. you need not disassemble the whole set, just open the back cover, connect one end of the cable to mother board and other end to the rigid flex board and that's it.
Click to expand...
Click to collapse
Do you think that this is my problem as since I dropped my HD2 I have no wifi (unless sat ontop of router) or bluetooth or fm radio, is it easy to get to the coax cable by removing back cover, whereabouts is it ?
raincybercafe said:
if the connectors on the boards are not broken then all you need is the coaxial cable with connectors on the two end. you need not disassemble the whole set, just open the back cover, connect one end of the cable to mother board and other end to the rigid flex board and that's it.[/QUOTE
Fixed it, opened up phone and spotted that at one end of the black wire the connector was not pushed onto the motherboard securely, I pushed it home and hey presto, wifi and Bluetooth now working, phew, Thanks for your help !
Click to expand...
Click to collapse
Thread for hardware mods
POSTING INTERNAL tf101 pictures
like 3g dongle ? internal sd cards? ssd?
removing the battery for 2 HDD 500go?
finding sd cards hubs? usb to sata cables?
? there is a place in the tablet for a 3g dongle?
there are 2 screws under the upper rubbers and the dock open easy
there is a lot of spaces avaible
My MIFI might actually fit in there, all I would need to do is supply it power somehow.
I'm no hardware engineer though, but if thats possible it would save you from the driver issues with a 3g dongle.
I wonder if it would be possible to check which pins from the adapter connect to USB - so we can make DIY USB adapter for those without a dock.
hmm adding an hdd would be very interesting, sata won't be very hard, powersupply will be.
Sent from my O2x with CM7
This is what I was looking for, looking to do some mods to the dock.
Thanks Markolino72.
Internally mount and wire a 32gb memory stick to the USB port so you get a 32gb hard drive added whenever you dock It might even have enough room for a portable USB hub so you don't lose use of the external usb port?
does anybody think it will be easy to make a DIY dock fix for those with battery draining issues like me?
It seems like it would be relatively easy - just make a switch to either connect or disconnect the cords coming from the docking point.
Or even better, maybe if you put the correct microcontroller in there you can have it switch the pins to floating, if it senses that there is no tablet connected (not sure about the details though)...
ydnality said:
does anybody think it will be easy to make a DIY dock fix for those with battery draining issues like me?
It seems like it would be relatively easy - just make a switch to either connect or disconnect the cords coming from the docking point.
Or even better, maybe if you put the correct microcontroller in there you can have it switch the pins to floating, if it senses that there is no tablet connected (not sure about the details though)...
Click to expand...
Click to collapse
Have you seen the post in the General forum (2nd page now I think)? Posted by Asus_USA themselves, if you prove the 6 steps that your dock has the issue you can get a new one! I really do hope that I can get mine exchanged, waiting on a reply from my local service center..
Regards.
In regards to the hardware mods, that really looks amazing. Would love to put in my mifi there as well, attach it via USB to charge = your own 3g model Maybe a little modding you could get the mifi to power on only when the dock is connected (remove the battery of the mifi?) so that when it powers on it'll power on the mifi as well. Only a few thoughts.
Maybe a little modding you could get the mifi to power on only when the dock is connected (remove the battery of the mifi?) so that when it powers on it'll power on the mifi as well.
Click to expand...
Click to collapse
it's a good thought but the mifi I have (novatel 2200) wont work without the battery, for some reason if the battery is bad or removed you cannot run usb, it must be the way they have the power run through the battery or charging. Not sure if all are like this or not.
andrewklau said:
Have you seen the post in the General forum (2nd page now I think)? Posted by Asus_USA themselves, if you prove the 6 steps that your dock has the issue you can get a new one! I really do hope that I can get mine exchanged, waiting on a reply from my local service center..
Click to expand...
Click to collapse
I talked to the Asus service rep about it. They currently won't give you a new one since they have a hardware upgrade to fix it. If you wanted a new one you needed to do before they solved the problem. I'm waiting on the upgrade part to be delivered for for mine. Should in a few days.
A switch should theoretically work. The guy at the service center said the replace something that goes into the hinge of the dock. Looking at the teardown pics, you can see a wire goes into each side of the hinge, so I think they replace the wires and maybe make a new connection somewhere on the dock.
Surprising how much wasted space there seems to be in the dock -- it's nowhere near as tightly packaged as the tablet itself. Looks like Asus can optimize the size or fit some more features in future versions, if they want...
Let me see if I am thinking correctly...Your saying using something like mifi installed via USB wires (will it be always on?) then connect via WiFi on your transformer? So basically your putting the mifi in a case that can never be opened without a screwdriver? I guess one would always have access for your other devices as well as long as the TF is in the vicinity.
P.S. I think I think this is a good idea, not decided though. I like to think of it in a real world application.
there is another post with a guy putting in an SSD, but it bulges at the keyboard. A 32g SD card would be nice.
Sent from my Transformer TF101 using XDA Premium App
typci said:
I talked to the Asus service rep about it. They currently won't give you a new one since they have a hardware upgrade to fix it. If you wanted a new one you needed to do before they solved the problem. I'm waiting on the upgrade part to be delivered for for mine. Should in a few days.
A switch should theoretically work. The guy at the service center said the replace something that goes into the hinge of the dock. Looking at the teardown pics, you can see a wire goes into each side of the hinge, so I think they replace the wires and maybe make a new connection somewhere on the dock.
Click to expand...
Click to collapse
You are getting the replacement part? bought mine on the US, but live in chile... would really like to somehow get the part that needs to be replaced and do it myself
tanguita said:
You are getting the replacement part? bought mine on the US, but live in chile... would really like to somehow get the part that needs to be replaced and do it myself
Click to expand...
Click to collapse
There's very little chance they'll give anybody the part, and nothing in the previous person's post suggested they're doing so for him.
Talk to Asus Chile and get it serviced by them:
http://www.asuschile.cl/
http://latin.asus.com/Static_WebPage/Service_center_chile/
knoxploration said:
There's very little chance they'll give anybody the part, and nothing in the previous person's post suggested they're doing so for him.
Talk to Asus Chile and get it serviced by them:
http://www.asuschile.cl/
http://latin.asus.com/Static_WebPage/Service_center_chile/
Click to expand...
Click to collapse
Well I ended up calling them. I would have to ship the dock to "someone" in the US, have them ship it to the repair center, fix it, ship it back and then ask that "someone" to ship it back to me... sooo, I'm basically screwed... I ended up with a nice 150US paperweight (not even considering the horrible light bleed on the transformer).
tanguita said:
Well I ended up calling them. I would have to ship the dock to "someone" in the US, have them ship it to the repair center, fix it, ship it back and then ask that "someone" to ship it back to me... sooo, I'm basically screwed... I ended up with a nice 150US paperweight (not even considering the horrible light bleed on the transformer).
Click to expand...
Click to collapse
Yeah, actually, I hadn't realized that but it does say it clearly on the product warranty page:
"Brazil and South American countries don’t support global service"
http://support.asus.com/warranty.aspx?SLanguage=en&p=20&s=16&m=Eee Pad Transformer TF101
took mine apart also and there is quite a bit of room.
i plan on putting a 128gb usb flash drive inside the dock and soldering onto the usb connections once i get all the bits in.
Any bigger pictures? Are the screws under the rubber feet?
just two screws under the rubber feet near the hinge then it just pulls apart from the top
had to take mine apart as the spring/clip mechanism for the sd card wouldnt lock the card in.
now the card is stuck in with no nails haha a simple fix.
This is good news. I hacked a Crystal HD decoder card (pcie), USB wifi dongle, a logitech nano receiver, and a 4 port micro usb hub (from a touch screen setup) into a Dell mini 9 and there was absolutely no room compared to this.
They even have covers for the USB ports, so if you remove a header and solder wires up you just have to hot glue / epoxy that cover from the back and you are money. Looks clean and stock.
I have an old 64 GB thumbdrive that might find a new home. Maybe a 1.8" usb HDD would fit in there with the battery, without the battery who knows.
Hello All,
All of a sudden, the plug wasnt connecting into the port like it always did and after i looked online, I seen that it happened quite a few times to others. It simply will not charge now. its been dead for a week and iv been contemplating what to do so i figured is take it here before i make the final decision. If anyone could give me some advice I greatly appreciate it.
It seems there are a few options, call viewsonic and try to get them to semd me a new one since I got it in Feb but im rooted so thats out, plus I dont want the hassle. Take it apart and try to re-soder(sp) it back on to the mother board- although I hear it is somewhat easy, but I could never do it.
SO my last possible option from what iv read online, is to buy the Malata Zpad/Gtab dock. From how I understand it, I will set my gtab in the dock and it will charge, but I have a few questions/issues with that.
1) I heard it doesnt come with a power cord. Is this true? Do i need to use the cord that my gtab came with and will it work to power this dock?
2) If this dock will indeed charge my gtab, and fully fix my issue, where is the best place to buy it/fastest shipping? The only ones Ive found are around $50 with free shipping(which im good with), are shipping from China and take up to a month to finally receive.
Again I have not been able to charge my gtab for a week, and need to find an alternative way, due to a faulty Ac port, which iv found many others online have the same issues.
please community, any would be a huge help. thank you all for taking the time.
bump
Any replies would be very helpful, thanks
The charger that comes with your gTablet works with the dock. The dock doesn't come with a charging cable. Just switch the cable to the dock and you're good to go. It'll start charging as soon as you dock it.
About two weeks ago, electroniccrap.com had them in stock. Yes, it's around $50. I actually got mine through them (ordered via Amazon). It was sent priority mail, so it arrived in less than a week.
I had the same problem and I open the tablet and soldered the AC port again back to the board. And it has been working fine for the last couple of months.
Re-soldering the connector shouldn't be a problem for an experienced person with decent tools. Ask around among your friends, neighbors, acquaintances -- surely someone can do it.
You might stop in at some local computer stores that do in-store repairs -- look for a technician with gray (or very little) hair, he'll probably be excited about the prospect of actually using his old soldering iron again, just like 'back in the day'!
Right after I got my G Tab, it fell off the desk and broke the charge socket in the unit. I figured out how to open the unit up and found the metal strap had been pulled lose and also the solder connections [I think there were four (4) had been pulled lose. The metal strap wouldn't hold the socket down on the board so I bought a tube of the new Locktie GEL Super Glue. I carefully added some drops of that to hold it to the board while I did the solder job. It has worked fine now for over a year thanks to the super gel glue.
We have tile floors in our home and shortly after fixing the socket, I again dropped it from about waist high, the thing bounced back up and I caught it in mid air. Other than a little scratch where it hit the tile the tablet has worked just fine. TRY THAT WITH AN IPAD AND SEE WHAT HAPPENS. These G Tabs are really rugged as the above demonstrates. It was also interesting to see the inside of the unit. Looks pretty simple. Hope this helps you repair yours.
Oh! another imprtant thing to remember. Before you start to pop the back off, on each corner there are little plug covers, when you pop those out there are Four (4) screws at each corner. Make that your first step to remove them first.
Please help, I miss my tablet.I had the common problem with the power thingy inside the tablet going out so i opened it to solder but did not fix.So i ordered the charging dock and waited for a month and a half.I get it today and was so excited to only plug it it and got power and charging everything is perfect,i go to swipe over on my arrow to unlock the screen and nothing!I have no touch controls on screen what so ever.But the soft keys work,they do not do me any good but they work.The home key takes me to my home page and mag glass goes to the internet.Does any body have any ideas of what could have happened or what i can do to fix this,please????
alcapone1130 said:
Does any body have any ideas of what could have happened or what i can do to fix this,please????
Click to expand...
Click to collapse
First, check for disconnected or loose cables inside the gTab.
Next, if it isn't a HW fault like loose cables, then connect the USB cable to the gTab and run this ADB command (you will have to install and set up ADB if you haven't already done so):
Code:
C:\SOME\PATH> [B]adb shell "echo -n 1 > /sys/devices/platform/tegra_touch/calibration"[/B]
Digitizer Cable/Connection
alcapone1130 said:
Please help, I miss my tablet.I had the common problem with the power thingy inside the tablet going out so i opened it to solder but did not fix.So i ordered the charging dock and waited for a month and a half.I get it today and was so excited to only plug it it and got power and charging everything is perfect,i go to swipe over on my arrow to unlock the screen and nothing!I have no touch controls on screen what so ever.But the soft keys work,they do not do me any good but they work.The home key takes me to my home page and mag glass goes to the internet.Does any body have any ideas of what could have happened or what i can do to fix this,please????
Click to expand...
Click to collapse
The attached pdf contains photos of the digitizer/cables and their connections inside the gtab. Check for loose connection and/or broken wires on both ends.
Al
aabbondanza said:
The attached pdf contains photos of the digitizer/cables and their connections inside the gtab. Check for loose connection and/or broken wires on both ends.
Al
Click to expand...
Click to collapse
Ok,First thank you so much for helping.Ok,One of the cables you shown does have two broken wires,it is the kind of short wire with black cloth like material over it that runs unde the shiny brown plastic piece.Is there a way to fix that or rig it to get me back up and touching again?Thank you again for helping me out,and you already pinpointed my problem,now i am hoping you can fix it,lol.
Where is the break?
alcapone1130 said:
Ok,First thank you so much for helping.Ok,One of the cables you shown does have two broken wires,it is the kind of short wire with black cloth like material over it that runs unde the shiny brown plastic piece.Is there a way to fix that or rig it to get me back up and touching again?Thank you again for helping me out,and you already pinpointed my problem,now i am hoping you can fix it,lol.
Click to expand...
Click to collapse
I assume since you didn't send in under warranty for the power connector that it's no longer under warrantly!
Exactly where is the break? Close to (or at) one of the connectors? Which end (motherboard end or digitizer end) of the cable? Obviously closness to the connector makes it more difficult. I have seen a post where another use had the break pretty close to the connector & fixed it though.
Al
I totally forgot that i made a youtube video yesterday,here is the address http://www.youtube.com/watch?v=kFNRtDhr5EQ I have been so stressed out about getting my gtab back it slipped my mind.Oh, the broken end is what plugs under the silver area not under the brown area.
aabbondanza said:
I assume since you didn't send in under warranty for the power connector that it's no longer under warrantly!
Exactly where is the break? Close to (or at) one of the connectors? Which end (motherboard end or digitizer end) of the cable? Obviously closness to the connector makes it more difficult. I have seen a post where another use had the break pretty close to the connector & fixed it though.
Al
Click to expand...
Click to collapse
I totally forgot that i made a youtube video yesterday,here is the address http://www.youtube.com/watch?v=kFNRtDhr5EQ I have been so stressed out about getting my gtab back it slipped my mind.Oh, the broken end is what plugs under the silver area not under the brown area.
alcapone1130 said:
I totally forgot that i made a youtube video yesterday,here is the address http://www.youtube.com/watch?v=kFNRtDhr5EQ I have been so stressed out about getting my gtab back it slipped my mind.Oh, the broken end is what plugs under the silver area not under the brown area.
Click to expand...
Click to collapse
If you magnify the digitizer circuit (lower photo in the pdf) you will see the label for each of the lines in the cable. Assuming the lines run straight thru, it looks like the ones that broke are the power & ground to the circuit (VSS & GND). That would explain the touch screen not working at all.
Hard to tell from the video where the breakis, but it looks real close to the connector.
Your best bet may be looking for someone who has a broken digitizer (outer glass) or gTab and is selling it for parts. I looked in the Marketplace forum here on XDA & there is one non working gtablet someone is asking $55 for. I also saw another one up for bid on ebay ($40 latest bid). You my have to ask if the cable is good on them.
Not a whole lot of options for repair. As you've already experienced, the cable is small & fragile.
If the connector has removable pins then you could remove the pins, solder the wire to it & reinsert the pins, BUT from the picture it doesn't look like they are removeable.
You could solder the 2 wires to the pins coming out the back of the socket but they look too small to easily solder to.
The last option would be to rigg the cable to work. There are a couple of possibilites but I would rather you consider the other options before suggesting a repair of the cable itself. If you can, see if you can take a closeup, high res photo of the back fo the connector where the wire broke. PM me & I'll send you my email address to send it too.
Al
aabbondanza said:
If you magnify the digitizer circuit (lower photo in the pdf) you will see the label for each of the lines in the cable. Assuming the lines run straight thru, it looks like the ones that broke are the power & ground to the circuit (VSS & GND). That would explain the touch screen not working at all.
Hard to tell from the video where the breakis, but it looks real close to the connector.
Your best bet may be looking for someone who has a broken digitizer (outer glass) or gTab and is selling it for parts. I looked in the Marketplace forum here on XDA & there is one non working gtablet someone is asking $55 for. I also saw another one up for bid on ebay ($40 latest bid). You my have to ask if the cable is good on them.
Not a whole lot of options for repair. As you've already experienced, the cable is small & fragile.
If the connector has removable pins then you could remove the pins, solder the wire to it & reinsert the pins, BUT from the picture it doesn't look like they are removeable.
You could solder the 2 wires to the pins coming out the back of the socket but they look too small to easily solder to.
The last option would be to rigg the cable to work. There are a couple of possibilites but I would rather you consider the other options before suggesting a repair of the cable itself. If you can, see if you can take a closeup, high res photo of the back fo the connector where the wire broke. PM me & I'll send you my email address to send it too.
Al
Click to expand...
Click to collapse
Wow,Thank you so so much,Can you get me in contact with the guy with the gtab for $55.00,i will buy it and transfer the cash to him immediately,that sounds like the best bet.I will msg you a really good photo still,incase i can not get my hands on the one for sale,but if i can let him know or maybe you could let him know that i will buy it quick enough maybe i can end up with it.I would really feel better just swapping the cable out with another.I will talk back with you tomorrow and again thank you for your time and great help,i really owe you.
Marketplace & Non Working Tab Links
alcapone1130 said:
Wow,Thank you so so much,Can you get me in contact with the guy with the gtab for $55.00,i will buy it and transfer the cash to him immediately,that sounds like the best bet.I will msg you a really good photo still,incase i can not get my hands on the one for sale,but if i can let him know or maybe you could let him know that i will buy it quick enough maybe i can end up with it.I would really feel better just swapping the cable out with another.I will talk back with you tomorrow and again thank you for your time and great help,i really owe you.
Click to expand...
Click to collapse
Here are several link for you
1. XDA Marketplace http://forum.xda-developers.com/forumdisplay.php?f=1321
2. Link to "Wanting to sell" subformum where I found the non working gtab (used forum search for gtablet) http://forum.xda-developers.com/forumdisplay.php?f=476
3. Link to not working gTab http://forum.xda-developers.com/showthread.php?t=1436549&highlight=gtablet.
Take a look at this post & email him to make sure you want it.
Al
aabbondanza said:
Here are several link for you
1. XDA Marketplace http://forum.xda-developers.com/forumdisplay.php?f=1321
2. Link to "Wanting to sell" subformum where I found the non working gtab (used forum search for gtablet) http://forum.xda-developers.com/forumdisplay.php?f=476
3. Link to not working gTab http://forum.xda-developers.com/showthread.php?t=1436549&highlight=gtablet.
Take a look at this post & email him to make sure you want it.
Al
Click to expand...
Click to collapse
Its amazing what a couple of stripped bread ties will doo,lol.I took a bread tie and stripped the paper off of it,cut it to the length I needed and wrapped the remaining wire to one end and pushed the other end of the tie inside the pin hole,lol.It worked like a champ! MY Grab has been up and running for over a month,I just knocked on my coffee table,lol.Thank you for helping me out I really appreciated you trying everything to help me.I am so happy to have it back,now if I can just figure out why I keep seeing black boxes on my games when I play them I will really be doing fine.Thank you again.
OK so I have a Viewsonic Gtablet. It broke this weekend. Well the charging port broke, the little pin in the middle of the port where the AC adapter blogs is loose, it is still in there but even careful cord placement will not charge it. I have just enough battery left to wipe it clean. But I was going to try to repair it.
So one, where to find decent instructions to open it up. I figure a charging port is an easy fix and I am no stranger to a soldering iron. Secondly I was going to sell it as I just ordered a new tablet. So would anyone be interested in this for parts or repair themselves. I was going to sell it before it broke for like $120 OBO. Can't do that now.
It is right now I wish they added USB charging to the device. At least I would have a backup plan...
Ken
Get a dock - 50 bucks, problem solved.
Sent from my Droid using xda app-developers app
devilock76 said:
OK so I have a Viewsonic Gtablet. It broke this weekend. Well the charging port broke, the little pin in the middle of the port where the AC adapter blogs is loose, it is still in there but even careful cord placement will not charge it. I have just enough battery left to wipe it clean. But I was going to try to repair it.
So one, where to find decent instructions to open it up. I figure a charging port is an easy fix and I am no stranger to a soldering iron. Secondly I was going to sell it as I just ordered a new tablet. So would anyone be interested in this for parts or repair themselves. I was going to sell it before it broke for like $120 OBO. Can't do that now.
It is right now I wish they added USB charging to the device. At least I would have a backup plan...
Ken
Click to expand...
Click to collapse
It is easy to pop the cover off the back of the Gtab. Here is a link to a video on how to do it.
http://www.youtube.com/watch?v=9M7lxllGOyc
A google search will also direct you to another site where the topic has been discussed.
Same thing happened to me: knocked it off a table while charging
Anyway, after looking into fixing the barrel connector jack I decided that it was going to be hard enough finding the part - much less getting it properly soldered onto the board, so I went a different route:
After finding the pinouts for the docking connector on the web at [*** see Note #1 ***] I went to [*** see Note #2 ***] and bought 2 connectors (in case I messed one up - the pins ARE pretty small).
I then soldered 2 wires to pins 26 (g) and 27 (+12) of a connector and cut the barrel plug off my charger and soldered the wires to the cable.
Works great.
Hope this isn't too late, but I figure in any case it might be helpful to someone in the future.
-jim
NOTES: Forum rules prhibit me from posting links, so here's how a human can find the places I would have listed
Note#1: pinouts
Google "rootzwiki Viewsonic Gtablet Dock Pins Discovered And Listed"
Note #2: The Kineteka eStore
Google "kineteka viewsonic gtab connectors"
I bought SKU# GTAB-DOCK-M-1 but the breakout board looked like an option as well