Hello,
I almost bricked my phone while trying to root it with heimdall (followed instruction from CM site). Then I managed to get it into the download mode with the Jig and flashed the JFD stock using Odin. Now the phone is stuck at boot. It keeps boot looping after the Vibrant screen. Is there a way to get the phone back to normal. Any help is appreciated.
i dont use heimdall but i would try using odin and see if that works. Grab the pit file and tar file and try to odin back to stock with odin.
You must have done something wrong when flashing with Odin/Heimdall. Read EVERYTHING carefully again, and try flashing with Odin/Heimdall again.
If you are using Windows, i would recommend you to use Odin since most people here uses Odin. In the CM7 site says that Heimdall its better than Odin, but everyone here is flashing with Odin and so far i haven't heard of anyone having problems with it. Make sure to use Odin 1.7 or a later one, those are the one that are stable, Odin 1.6 or lower its unstable.
Yeah most people use odin. Whenever I have problems like this I do these steps and its always worked for me hope the same goes for you! Seems long but all the steps are really simple.
1. Pull out battery, sd card, and sim card
2. Let phone sit with battery etc. out for at least 10 min
3. Install sim card, sd, and battery.
4. Plug in USB and open odin, do not connect usb to phone yet
5.hold the volume up and volume down buttons (don't hold down the power button) while holding volume up and down plug the micro usb into your phone. This should put your phone into download mode.
6. At this point most times odin will recognize my device but sometimes I just have to unplug the micro usb and re-insert for odin to recognize. Just choose the stock pit and pda and flash.
7. Your phone is now stock!
Sent from my SGH-T959 using XDA App
GYM_RATttt612 said:
Yeah most people use odin. Whenever I have problems like this I do these steps and its always worked for me hope the same goes for you! Seems long but all the steps are really simple.
1. Pull out battery, sd card, and sim card
2. Let phone sit with battery etc. out for at least 10 min
3. Install sim card, sd, and battery.
4. Plug in USB and open odin, do not connect usb to phone yet
5.hold the volume up and volume down buttons (don't hold down the power button) while holding volume up and down plug the micro usb into your phone. This should put your phone into download mode.
6. At this point most times odin will recognize my device but sometimes I just have to unplug the micro usb and re-insert for odin to recognize. Just choose the stock pit and pda and flash.
7. Your phone is now stock!
Sent from my SGH-T959 using XDA App
Click to expand...
Click to collapse
What? I don't undestand how the phone will turn on with out press the power botton. I try your process and nothing. I have my phone brick thank you to CyanogenMod 3.1, after you install is impossible uninstall. I try flashing the NAND restore.
real simple here..
just turn ur phone off
turn on odin and make sure u have ur samsung drivers installed.
plug ur phone in with the usb
now hold down the two volume buttons first and then the power and let go of power when u see the vibrant logo pop up.
then it will pop up in dl mode.
This is how i do it all the time....
ps.. it may take a few takes but it always works
The phone was stuck at boot only after I tried to odin back to stock JFD using Odin 1.7. I tried several combinations (w/ or w/o pit, repartitioning etc) mentioned in several guide across the forum. But nothing worked, then I tried something stupid. I tried to flash KA7 through odin, as my phone had 2.2.1 when I got it, and that resulted in a complete brick. There is no response even to the Jig.
I finally called T-mobile and requested a replacement as the mobile was only 2 weeks old.
Related
I googled how to reset my phone back to factory settings and they gave me this link
"[STOCK ROM] Odin3 One-Click Downloader"
(cant link links)
i misread that it was for the captivate, and i went through with all the directions.
now my phone keeps flashing an AT&T bootscreen and i cant get it in recovery mode..
help?
same here... that odin thing isn't working. Im just stuck at the vibrant boot screen. I know how to get into download mode but my pc or ODin doesnt recognize that i have my phone in. it's suppose to light up yellow or something. the tar files and all of that stuff is so confusing.
nevermind, i found the Odin program for the samsung vibrant and re did it.. but i still have BOTH at&t boot screen at the tmobile vibrant boot screen.. anyone know how to get rid of that? it would be much appreciated thanks!
http://forum.xda-developers.com/showthread.php?t=741027
where did u find it.. please share..
Edit: NVM..
stepinmyworld said:
same here... that odin thing isn't working. Im just stuck at the vibrant boot screen. I know how to get into download mode but my pc or ODin doesnt recognize that i have my phone in. it's suppose to light up yellow or something. the tar files and all of that stuff is so confusing.
Click to expand...
Click to collapse
You may have tried this but these are the steps that eventually worked for me.
1. Put your phone in download mode by plugging it in and then holding Vol Up+Down and Power. As SOON as the screen goes black release power but NOT Vol Up+Down.
2. Launch Odin
3. Unplug your phone.
4. Load the pit and pda files into odin.
5. Plug your phone back in. You should now see one of the small blocks turn yellow and show you the com port. If not, something is wrong with your drivers.
6. Click start. If it flashes, great. If it hangs at File analasys then repeat 1-5.
6a. If Odin hangs at cache.rfs then move on to 6b.
6b. Unplug your phone (Odin will say it was removed) and remove the battery. DO NOT SHUT DOWN ODIN!!!!!!
6c. Put the battery back in and plug it back into your computer and put it back into download mode using step 1.
6d. Press start on Odin and it should now flash.
Again, this worked for me, it may have been a fluke and I'm not willing to try it again. Good luck!!!
Does not boot!
What if the phone does not boot. All happened after I tried to flash the kernel back to the stock one. USB plugged in, battery is fully charged- still no sign of life. Any solution for that? No recover or download mode!
setzer715 said:
You may have tried this but these are the steps that eventually worked for me.
1. Put your phone in download mode by plugging it in and then holding Vol Up+Down and Power. As SOON as the screen goes black release power but NOT Vol Up+Down.
2. Launch Odin
3. Unplug your phone.
4. Load the pit and pda files into odin.
5. Plug your phone back in. You should now see one of the small blocks turn yellow and show you the com port. If not, something is wrong with your drivers.
6. Click start. If it flashes, great. If it hangs at File analasys then repeat 1-5.
6a. If Odin hangs at cache.rfs then move on to 6b.
6b. Unplug your phone (Odin will say it was removed) and remove the battery. DO NOT SHUT DOWN ODIN!!!!!!
6c. Put the battery back in and plug it back into your computer and put it back into download mode using step 1.
6d. Press start on Odin and it should now flash.
Again, this worked for me, it may have been a fluke and I'm not willing to try it again. Good luck!!!
Click to expand...
Click to collapse
i am completely lost when it comes to ODIN. I need to know the exact program to use. I have Odin Multi Downloader v4.03.. but it keeps giving me file path error and stuff. I have the right drivers i think because it does recognize my phone. im just so confused with this rar tar stuff. I would pay someone 20 dollars through paypal if they can walk me through this.
stepinmyworld said:
i am completely lost when it comes to ODIN. I need to know the exact program to use. I have Odin Multi Downloader v4.03.. but it keeps giving me file path error and stuff. I have the right drivers i think because it does recognize my phone. im just so confused with this rar tar stuff. I would pay someone 20 dollars through paypal if they can walk me through this.
Click to expand...
Click to collapse
I don't want your money, but if you PM me I will try to type up a detailed how to.
mffu said:
What if the phone does not boot. All happened after I tried to flash the kernel back to the stock one. USB plugged in, battery is fully charged- still no sign of life. Any solution for that? No recover or download mode!
Click to expand...
Click to collapse
What have you done to put it in download mode? You should power off your phone, plug it into your computer. It should then enter the charge mode where you see a picture of your battery being charged (or if you were like me and screwed up somewhere you may see a little picture of a phone, computer and yellow triangle in between them). If you get either of those then press and hold all three VOL up, VOL down and power. AS SOON AS the screen goes black release ONLY Power and it should go into download mode.
If you plug your phone into your computer (powered off) and nothing happens then you just be bricked. Call TMO and play dumb and hopefully get a replacement.
Ok,
The_Chrome_Coyote really helped me!!!! Thank you so much and im back up and running. There was something missing from the original tutorial, not that we should be spoon fed but I didn't have the WinRAR program on my pc and didn't know I needed to extract anything. I was looking for exe. for it to be a program and just open it. It's a little more complicated than that. I added my additions in BOLD
The_Chrome_Coyote's Original post to me:
Odin isnt that hard, its just REALLY picky about working.
Firstly you need to download the Samsung drivers for your OS which can be found:
http://forum.xda-developers.com/showthread.php?t=728929
added:
Second you need to make sure you download WinRAR x86 (32 bit) 3.93 (google it and you should be able to get it) otherwise if your pc doesn't have a program to recognize rar and tar files, you are out of luck.
then read this thread from JAC:
http://forum.xda-developers.com/showthread.php?t=734475
1. Now, Extract ODIN from its .rar and place the .exe on your desktop
2. Extract the .pit file from its.rar and place that on your desktop
3. Place the JFD .tar file on your desktop but DO NOT EXTRACT
Now you can use ODIN
4. Start ODIN Odin3. [Android + SLP], through ODIN select the .pit file
5. Hit "PDA" button, and through ODIN select the .tar file
6. Plug your TURNED OFF PHONE into the USB cable
7. Wait for the Battery/ charging indicator to start
8. HOLD VOL UP+ VOL DOWN+ POWER, as soon as the screen goes black RELEASE POWER, and continue to HOLD VOL UP+ VOL DOWN Until it enters download mode. Which should happen quickly and looks like a men at work highway sign.
9. If a COM port has turned Yellow in ODIN, then the device has been recognized. If it hasnt, unplug and plug your phone back in.
10. Dont select any options other than whats set at default.
11. Hit Start and be patient, takes me maybe 5 minutes to get back up and running.
NOTE: If you do not see a blue progress bar on the phone's screen after a minute;
11a. Turn your phone off by pulling the battery.
11b. CLOSE ODIN
11c. Start at step 4 again.
ODIN needs to be open and ready to flash before the phone is plugged in, in my experience. Its very picking about this, and not everyone has this issue, but I did and following all these steps helped me flash my phone more times than I can count the other day haha.
Hope this helped! and your $20, donate it to Wes, JAC, or Eugene to keep them making great stuff for our phone.
Reply With Quote
Thank you thank you thank you
mffu said:
What if the phone does not boot. All happened after I tried to flash the kernel back to the stock one. USB plugged in, battery is fully charged- still no sign of life. Any solution for that? No recover or download mode!
Click to expand...
Click to collapse
Same thing happened to mine when i tried odin. Now all i get sometime when it come on. are 7 rows of text that seems to be a code on screen in amber. Ishipped back 2 samsung. Since t-mobile won't take it after 14 days.
ok I screwed up guys.
I installed ROM manager from the market, flashed clockwork, it asked me if I wanted to partition and I said yes.
Now I just get a black screen at boot. I've managed to run odin and it says success. But I still just get a black screen after boot.
Little help?
I do have to say that if YOU DO NOT KNOW HOW TO EXTRACT A COMPRESSED FILE (RAR, ZIP,ETC) YOU HAVE NO BUSINESS FLASHING YOU'RE PHONE!! Odin or otherwise.
I am not being mean but at least stick to update.zip files flashed through recovery and make sure you read reviews of other users first, and understand the instructions completely.
Sent from my SGH-T959 using Tapatalk
daddysays said:
I do have to say that if YOU DO NOT KNOW HOW TO EXTRACT A COMPRESSED FILE (RAR, ZIP,ETC) YOU HAVE NO BUSINESS FLASHING YOU'RE PHONE!! Odin or otherwise.
I am not being mean but at least stick to update.zip files flashed through recovery and make sure you read reviews of other users first, and understand the instructions completely.
Sent from my SGH-T959 using Tapatalk
Click to expand...
Click to collapse
First: everyone was a noob at one time, so simmer down.
Second: Pleast post an update.zip that will make my phone work.
Cannot get past Galaxy S boot screen
I was using clockwork recovery installed through an update.zip file on my sd card. everything was working fine for about a day and then when i powered my phone off the next day and powered it back on it would not boot up past the Galaxy S screen. it goes to the Galaxy S screen and then goes blank but my hard keys stay lit up while my lcd is completely blank. I tried using the Odin method described in this thread and it seemed like it was going to work but i still cannot get past the boot screen. please help. willing to donate if needed
jmoney1017 said:
I was using clockwork recovery installed through an update.zip file on my sd card. everything was working fine for about a day and then when i powered my phone off the next day and powered it back on it would not boot up past the Galaxy S screen. it goes to the Galaxy S screen and then goes blank but my hard keys stay lit up while my lcd is completely blank. I tried using the Odin method described in this thread and it seemed like it was going to work but i still cannot get past the boot screen. please help. willing to donate if needed
Click to expand...
Click to collapse
If you can see the samsung logo you are fine. Load up recovery and try a full wipe first. If that fails then you can odin back to stock and root again.
Sent from my SGH-T959 using XDA App
1. If you have questions, there is a q and a forum for this device!!!!!!
2. THIS IS THE DEV PART OF THE FORUM. IE FOR DEVS POSTING STUFF FOR THE PHONE!!!!!
3. Learn how to Google. Not that hard. Example, you don't know what the *.rar extension is. GOOGLE IT!! Google knows everything.
4. If you don't have basic android or computer skills, don't try anything stupid. You do have a chance to brick your phone, even the pros like cyanogen have bricked their phones.
5. Don't offer cash for someone to fix your phone. Keep it in qna and some one will help you. Save your cash for the development that work hard on making these things work.
6. Can a mod please move this thread to qna.
7. THE MOST IMPORTANT THING. USE THE SEARCH FINCTION BUILT ONTO THE FORUMS. IT WILL SAVE YOU TIME AND THEN YOU WILL NOT LOOK LIKE NOOBS THAT JUST GOT THIS PHONE BECAUSE IT HAD AVITAR IN THE BOX!!!!!
Sent from my SGH-T959 using XDA App
cache.fs problem in odin
setzer715 said:
What have you done to put it in download mode? You should power off your phone, plug it into your computer. It should then enter the charge mode where you see a picture of your battery being charged (or if you were like me and screwed up somewhere you may see a little picture of a phone, computer and yellow triangle in between them). If you get either of those then press and hold all three VOL up, VOL down and power. AS SOON AS the screen goes black release ONLY Power and it should go into download mode.
If you plug your phone into your computer (powered off) and nothing happens then you just be bricked. Call TMO and play dumb and hopefully get a replacement.
Click to expand...
Click to collapse
I FOUND A SOLUTION TO THE CACHE.RFS PROBLEM!!
http://www.fractionalphones.com/?p=121
Hello everyone. I have a question about the current state of my Vibrant. Coming from a G1, I just upgraded to the Vibrant and have been loving since. I rooted my device, installed Clockwork Recovery, and flashed a new Rom. I decided to switch back to the stock rom but now when I turn on my Vibrant, it just sits at the Vibrant Samsung boot screen... Here are the steps I did up until this point:
1. Starting from the Stock T-Mobile rom, I applied Root update zip but booting into Recovery Mode (Holding down the volume Up/Down buttons and then pressing the Power button).
2. Installed Clockwork Recovery, and then did a Nandroid Backup.
3. Using Clockwork, I installed Eugene's Vibrant7 rom (I left create ROM Backup and Wipe Data options checked)
4. Vibrant7 rom flashed successfully but decided to switch back. So I used Clockwork to boot into manual recovery mode, selected Nandroid and then Restore
After it finished the Restore, it now sits at the Vibrant Samsung boot screen everytime I power it up... I'm thinking I should have not have used the Nandroid Restore to revert back to the stock ROM (unless I'm totally mistaken, I never used Clockwork Recovery before and have flash roms before with my G1).
At this point, could I just reflash back to the stock firmwire using ODIN (Directions from this thread [ROM] OFFICIAL T-Mo Vibrant JFD ODIN/Nandroid Backup Images 7/29/10 (Tested/Working) in the Vibrant/Android Development section). Would that take care of my problem or is my phone currently 'bricked' or SOL?
Thanks in advance for any help or clarification
yeah just odin back to stock... Read the directions carefully
this exact same thing is happening to me. I have tried to follow the instructions to odin. but when I hold volume down and power it just keeps rebooting to the vibrant page. but if I hold volume up and down and power I can get into recovery but non of the options fix my problem. Am I screwed or am I doing something wrong.
i'm having the same problem...stuck on boot screen
i'm on the bell network, are there instructions on how to use odin to fix my phone?
Try this,
1. Take out simcard ms and battery
2. Make sure you have the right drivers for your os
3. Open odin
4. Put your battery back in
5. Hold both volume up and volume down, using two fingers,
just to make sure your not missing a button.
6. Slowly... SLOWLY... put the usb into your phone while doing step 4
7. Continue to hold,
8. Should be in dl mode
If your not take out the battery and repeat 4-7. If odin doesn't recognize your phone, try unplugging the usb wire and reconnecting it.
flashed a sgh t959 with a galaxy s i9ooo kernel oops
hi im stuck in manual mode and when i try to boot the screen shows two different galaxys s screens then goes back to manual mode and i cant get into down load mode it just goes back two manual mode was trying to root used wrong file i think im screwed i flash with oden and used i9000xxxhph tar file
Same with me, I think I soft bricked my vibrant, so I tried to restore to stock rom using odin. Odin detects it and runs stock rom just fine, but once it was restarting, the phone would not still boot up and would stay stuck at the vibrant samsung screen. I tried other roms such as froyo no brick, and i9000 stock rom also, would not boot also, just stuck at the samsung screen. What do I do? Odin works through the process fine though......why isnt it fixed?
Daddy_617 said:
Try this,
1. Take out simcard ms and battery
2. Make sure you have the right drivers for your os
3. Open odin
4. Put your battery back in
5. Hold both volume up and volume down, using two fingers,
just to make sure your not missing a button.
6. Slowly... SLOWLY... put the usb into your phone while doing step 4
7. Continue to hold,
8. Should be in dl mode
If your not take out the battery and repeat 4-7. If odin doesn't recognize your phone, try unplugging the usb wire and reconnecting it.
Click to expand...
Click to collapse
OMG MAN!!! i love you! this did it for me, i even went and bough AND made a jig but none worked, didnt boot up into dl mode, just stayed stuck at vibrant boot screen, this did it for me, thx man, saved me hours of stress
yes yes yes! your mistake was using the power button! Lol.
FUTURE NOTE: if you upgrade to any gingerbread roms.... new bootloaders are required. If your JIG didnt get you into download mode before...... then it isn't working right. Once your into the the new Bootloaders for gingerbread, the sequence is........ HOLD VOL UP and POWER until you trigger DL mode. No USB required.... DO NOT FLASH NEW BOOTLOADERS WITHOUT A WORKING JIG IN YOUR POSSESION. TEST IT BEFORE YOU FLASH. I had...... an experiance.... lol
Not working
ParaMount33 said:
OMG MAN!!! i love you! this did it for me, i even went and bough AND made a jig but none worked, didnt boot up into dl mode, just stayed stuck at vibrant boot screen, this did it for me, thx man, saved me hours of stress
Click to expand...
Click to collapse
I tried all the instruction still stuck on Vibrant logo if i connect cable the Loader pix cums but doesnt load or show me battery image what to do now? also Odin doesnt recognize neither i can go to download mode!!!!!
If you can get in DL mode you are halfway there, next make sure you have correct drivers. Uninstall current drivers and reinstall correct drivers. Odin can be funny sometimes, you might need a new USB cable, try every USB port as well.
You can also use the All In One (AIO) program to get drivers and back to stock. If you are having issues with Odin try this
http://forum.xda-developers.com/showthread.php?p=11358713
sent from the depths of helly bean
hi,
Once i gt a prob restoring. But then I re-flashed the ROM which the nandroid backup was taken and then in CWM selected advance and gave restore data option(as i remember).. (it was not full restore with system..b/c I flashed system separately)
You can go back to stock using ODIN .. as mentioned by Daddy_617 previously.
tc
Also if Odin doesn't work for you try Heimdall. I've seen post where this has worked for others.
Vibrant stuck on "Vibrant Samsung"
Daddy_617 said:
Try this,
1. Take out simcard ms and battery
2. Make sure you have the right drivers for your os
3. Open odin
4. Put your battery back in
5. Hold both volume up and volume down, using two fingers,
just to make sure your not missing a button.
6. Slowly... SLOWLY... put the usb into your phone while doing step 4
7. Continue to hold,
8. Should be in dl mode
If your not take out the battery and repeat 4-7. If odin doesn't recognize your phone, try unplugging the usb wire and reconnecting it.
Click to expand...
Click to collapse
I tried this but the say thing keeps happening ... really need help
So I was using Odin to flash the stock ROM so I could flash to Nero v3...Had some trouble with Odin now this icon is all I can get the phone to show me. Attempts to get back into download mode haven't worked. I've done the Volume up + Volume - and Power button.
Did I brick my phone?
Did you have voodoo enabled when you flashed?
Unplug phone. Open odin. remove battery. Plug phone in. hold volume up/down keys. plug battery back in. should auto boot into download mode. I've seen that screen a few times and managed to go back to stock make sure its 512 pit jfd rom. Not ji6 513.
Sent from my SGH-T959 using XDA App
That icon looks so familiar...
Do what boystuff said...exactly. Don't touch the power button at all. And for me, I had to also remove both the sim and sd card along with the battery.
So to recap: take all 3 out, connect the phone to the computer via usb cord, hold down both volume buttons, then while holding them down insert the battery. It'll kick you into download mode.
Sent from my Vibrant using XDA App
same issue somewhat....,.
Having trouble using ODIN!!
as now I did the steps and all I have is the phone will boot up through the tmobile screen & S after that screen goes black with the 4 hour button home row lit up.???
As for the recovery I get the following when booting it:
move_check Start..!!
checksum confirmation need_checksum(1300........)
mbr_checksum in header : 4:1
mbr checksum: 533a4003d.........
mbr checksum error
movingand checksum cofirmattion fail
movi_checking done!
update media, please
update media, finished
#manual mode #
appling muti csc
installin multi csc
Much help would be appreciated!!! Have to work all day today which will be slow, so I can work on fixing this. My main question is what type of file is pit & tar? Pit properties is coming up as a window shell comand, Tar opens with unknow app? Not sure if this is my problem or not, I get ODIN to run and complete the steps and end up with the above.
Using Odin V1.3
512.pit
t959UVJI6
bnielsen40 said:
That icon looks so familiar...
Do what boystuff said...exactly. Don't touch the power button at all. And for me, I had to also remove both the sim and sd card along with the battery.
So to recap: take all 3 out, connect the phone to the computer via usb cord, hold down both volume buttons, then while holding them down insert the battery. It'll kick you into download mode.
Sent from my Vibrant using XDA App
Click to expand...
Click to collapse
Hi I am having the same issues here and i did everything that you said and i am still seeing the same connect your phone to computer screen and i did have voodoo enabled before i was attempting to odin back to stock. is there anything i can do i really hope that this is not a $500 paperweight i have odin v3.10 and 512.pit also
raziel26 said:
Hi I am having the same issues here and i did everything that you said and i am still seeing the same connect your phone to computer screen and i did have voodoo enabled before i was attempting to odin back to stock. is there anything i can do i really hope that this is not a $500 paperweight i have odin v3.10 and 512.pit also
Click to expand...
Click to collapse
Get back into download mode and flash Eugenes Froyo That Does Not Brick, that will wipe everything and fix your Voodoo issues. From there you should flash back to JFD then to anything you want.
icandy75 said:
Get back into download mode and flash Eugenes Froyo That Does Not Brick, that will wipe everything and fix your Voodoo issues. From there you should flash back to JFD then to anything you want.
Click to expand...
Click to collapse
thats the problem i cannot get into downloader mode
Have you tried the batt pull method? You could also try adb reboot download. If these do not work for you your will need a Jig to get her back to life.
the Adb method does not work because the pc will not recognize that there is a usb plugged in with the phone and what is the batt pull method and if a jig is something hardware rigging i am a complete idiot when it comes to that
raziel26 said:
the Adb method does not work because the pc will not recognize that there is a usb plugged in with the phone and what is the batt pull method and if a jig is something hardware rigging i am a complete idiot when it comes to that
Click to expand...
Click to collapse
Just pull the batt out. Plug usb to phone only first, hold down volume + and - and don't let go then plus in usb to your computer while still holding volume keys and put battery back in. That should work for you. A Jig is a rigged hardware piece that forces your phone to Dl mode.
where is the link for the eugene froyo files? Pda & Pit files needed please link.
To get into downloader mode this works everytime for me....
Start up ODIN, make sure phone is OFF (take out battery) plug back in
hold both the volume up/down (or more near center)....
While holding that plug in the USB connector,
this methods works all the time.
Im stuck in bootloops currently and do anything no responses yet.
Sweet! that totally got me back into download mode...next question why am i getting stuck at file analysis?
bnielsen40, Boystuff, and Osuhsxr are totally right about the vol keys no crazy special soldering required.
osugsxr said:
where is the link for the eugene froyo files? Pda & Pit files needed please link.
To get into downloader mode this works everytime for me....
Start up ODIN, make sure phone is OFF (take out battery) plug back in
hold both the volume up/down (or more near center)....
While holding that plug in the USB connector,
this methods works all the time.
Im stuck in bootloops currently and do anything no responses yet.
Click to expand...
Click to collapse
Check your PM.
Today was I was watching the video on how to flash darky's resurrection.zip rom,
then zi tried flashing it to my wifes Vibrant , I folloeed the video step by step. I used odin I get the green light saying the phone passed then when it reboots it get stuck on the galaxyi900 screen and it doesnt boot up. Ive flashed the thing with odin at least 10 -15 times after and still no luck, it keeps getting stuck at the opening. My wife says if I dont fix it I have to buy her a new phone. Someone save me please!!!!!!
LMAO........... yeah my wife said the same thing...... sounds like you may have not disabled the voodoo lagfix before the flash.
you will probably need to flash back to stock. I am not sure what is stock on this phone I am going to assume it is the same Vibrant.
If you can get into recovery and you did have voodoo installed disable it. If not you can disable it on your phone and copy the folder and then load it into the internal sd card messed up phone and replace the old folder.
Then you may need to use Eugenes froyo that does not brick as a intermediary flash. if you can Odin that (use Odin 1.7) then when it you flash it do not check the repartition box. When it is beginning to reboot, do not let it fully reboot, pull the battery. Then Redo the Odin as described below:
Open Odin.exe and plug a usb cable to your computer that will connect to your phone (do not plug it in to the phone yet, just the computer)
Hold down both volume buttons at the same time and while holding them down plug the usb into your phone. You should see a COM message show up in Odin.
Leave all check boxes the way they are. Check the repartition box.
Click the PIT button and select the 512.pit file
Click the PDA button and select T959JFD.tar and then click Start
When it is done you will be back at stock. Then Root the phone and go from there.
still getting the loop! this phone is jacked up. I can enter download without pressing the power button, cause it turns on and off itself
My phone just keeps flashing the opening Samsung galaxy s gt-i9000
Oh good I don't know the pit or .tar files sorry
Sent from my SGH-T959 using XDA App
Omar50 said:
still getting the loop! this phone is jacked up. I can enter download without pressing the power button, cause it turns on and off itself
Click to expand...
Click to collapse
take the battery out, wait 30 seconds, plug the usb cable in, and then hold both the volume buttons and slide the battery in. Presto! Download mode.
This has saved me numerous times lol. Then just flash JDF like oka said
i dont have problem entering download mode. When I flash with odin I get a pass on it. but when the phone reboots it stays on the opening screen go on and off
i download the heimdall suite 1.1.1 and the necessary windows program to run it. when i plug my phone into download mode heimdall start button isn't accessable. am i missing something?
figured out hoew to get access to start button, dont use partition. now it gets error on recognizing the device. Im so frustrated right now I need a smoke!!!!!!!
Omar50 said:
figured out hoew to get access to start button, dont use partition. now it gets error on recognizing the device. Im so frustrated right now I need a smoke!!!!!!!
Click to expand...
Click to collapse
Depends on what you smoke........
You may need the pit 513 file instead of the pit 512 file, these mapping files are a bit different and it may be a cause. Hard to know without seeing the phone
Also you could do a full wipe if you can get into recovery, wipe cache, phone reset and dalvik wipe (in advanced) then try That may work better for you.
It is recoverable.......... and also the best way to get your wife to calm down......... a romantic restaurant with candle light........ you go on Tuesday and she goes on Thursday........
Hope you get it fixed..........
thanks for the support but no luck I tried 513 pit nothing my phone still wont boot up I still get the opening screen then it shuts off and starts again.
im really having a bad day now i tried flashing the stock rom 2.2 with odin now the phone wont even power on! i guess its really a brick. i bought myself a paper weight
So I got my hands on a vibrant the other day... fresh out my friends closet. It was running stock eclair.
I successfully rooted and flashed cwm via rom manager.
Then I tried to flash Asgard 3.2 via cwm but I got a bootloop with a woman's voice saying "convert data partition, not enough space on partition.
Any thoughts? Thanks in advance for the help guys.
If it helps I forgot to mention that I can't get into recovery either. Both volume buttons and power just makes the screen black and the capacitives stay lit.
Volume down and power just cause to boot normally.
What should I do?
Sent from my LG-P999 using XDA App
Anyone?
Sent from my LG-P999 using XDA App
OK, First of all, your NOT bricked because it can still power up
.AIO Baywolfs program to get it into DL mode and restore it to JFD. Eclair 2.1 this will be the only time you will allow repartition.
After that reinstall Rom Manager, flash CW recovery again.
Then put it into recovery mode again, and select reinstall packages, may have to do it twice, then you'll have the green menu for flashing ROM's
Then select the Rom u want to install, if its in zip form ya gotta do it with CWM
If its in a tar file use ODIN 1.71 above, and don't forget to add the 512 pit file also, don't repartition the drives un-tick it
Also whether you CWM or odin it, just make sure in Odin un tick re-boot after install, at CWM select wipe data/factory reset then do the cache, same thing when odin's finished, otherwise you'll prolly get a boot loop.
Then go to re-boot and let it simmer for about 10 mins average to allow everything to be right before you start flipping thru it.
Thank u so so much very informative post. Only one problem: I think the USB port might be messed up because when I plug it in I get a "USB device not recognized error." That'd with the Samsung drivers installed. I rooted through a flahable zip. I guess ill try with Odin to see if I can get any USB functionality once I'm home. If not do I have any other options??
Sent from my LG-P999 using XDA App
Yes, HOW TO GET INTO DOWNLOAD MODE
* Read the noob guide if you are asking why you would need this *
On PC, open ODIN
Connect USB to PC (not phone)
Pull Battery on phone and replace it
Press and hold in both volume buttons
Connect USB to phone, wait at least 3 seconds (still holding volume)
Release when you see the Yellow Triangle
Remember to use Odin you must be in DL mode first, before you attach the USB cable to the phone, otherwise Odin wont detect the phone , once you see the yellow high-lite in the top left corner of Odin with a com port addy, you can relax because you can flash the phone .
Also start with the stock Eclair JFD 2.1 tar file and the 512 pit file, allow repartition, just this one time, and allow it to auto reboot as well, after that first restore, and other subsequent flashes, un tick partician and auto reboot, so you have control over wiping data and cache, BEFORE rebooting the first time with that brand new ROM flash to avoid boot looping!
Thanks so much for ur help thus far man. But my suspicions about the usb port being messed up have been confirmed, I think.
I pulled the battery, replaced it, had odin opened and usb connected to pc (not phone).
Then with both volumes held i plugged the phone in. the same "USB device not recognized" message pops up on pc, and then the woman's voice "convert data partition, not enough space on partition."
Starting to lose hope man... what do you think?
I think you may need new Samsung Drivers. Go to the guide below and go under the section called "4. Odin" and look for the link to get Samsung Drivers. Hope this helps you!
http://forum.xda-developers.com/showthread.php?t=1307637
Sent from my SGH-T959 (Samsung Vibrant)
You need the proper USB drivers
sounds like you have messed up USB drivers.
i freaked out about that stuff too the first time i flashed.
here's what I did, it may help you.
1) delete any Samsung Composite USB devices in your Device manager.
2) pull your sim card, sd card and battery
3 connect your USB cord to the computer and phone
4) hold both volume up and volume down
5) insert battery now
6) you should be in download mode now (see yellow triangle with lightning bolt and android)
7) run Odin and flash stock JFD.
Guys thanks so much for all your help.
Unfortunately I have tried everything suggested here and still have had no luck getting any USB functionality out of this phone.
I still don't understand why I can't just get into recovery (i.e. not something through usb) to fix the partition issue myself to get Linda to stop *****ing.
Install Samsung kies, or uninstall and then reinstall if you already have it. It will delete and reinstall your drivers. You have a driver issue
Sent from my SGH-T959 using XDA App
Tried the kies suggestion... still same.
Just to reiterate:
I plug it in with battery in and pressing no buttons, and get:
on pc - usb device not recognized
on phone - nada
I plug it in holding both volumes and but battery back in after and get:
on pc - usb device not recognized
on phone - loading circle, linda *****ing and then charging battery screen
Anymore suggestions???
Have you tried a different USB cable? different Ports on your computer?
Sent from my SGH-T959 using XDA App