Hi guys,
I think this questions was already asked for every other phone but i'm not sure if you can tranfer the answers.
basically what i would need is a scheme of the pins of the micro-usb port like in the samsung sound station dock.
i want to built an adapter (micro-usb) to usb (for charging) and 3,5mm headphone jacks (for listening to music).
you can also buy them but i'm not sure if they work with the i9100 aka if theres a universal standard for the pin scheme.
would i also need to put the phone into a special mode with an resistor to play music over usb?
any help is appreciated
thx in advance and best regards,
canedha
[bumpedybump]
Related
Hi all,
As per subject...
Anyone know if such as cable is available?
I was planning on getting the new 3-1 Adaptor for the TYTN to make use of the 3.5mm jack and charging feature in my car.
The thing is, the cable for this adaptor is very short and cannot be hidden easily when in the car. So, I was thinking of using an extension cable of some sort, so the adaptor could be more easily hidden elsewhere under the centre console.
Many thanks.
USB Stupidity
Hi,
Affraid i didn't find anything either, and wanted to do the same thing.
I resorted to buying the cable from expansis and "Adapting it my self"
The project was fairly simple, and if your happy with a soldering iron and a multimeter you should be fine.
I now have a small connector on my dash that will disapears under the dashboard to a breakout box. All i basicly did was chop off the box that has the two female connectors in it, extend the wire with an old cut up parralel printer cable (multicore and was lying arround) and then terminated in a project box from maplins.
This has two headphone sockets, (audio out stero, and mic in) as well as a USB socket to charge the phone. (the plan was to have the USB socket be usable for data... but that bit went a bit wrong...
Still from the testing i have done, i now have tomtom and WindowsMedia mp3 play back comming through my car stero, and my VarioII reports to be charging. Havn't had a chance to test it on a long drive yet, i think i might still need a beefier 12Volt to USB adapter.
If anyone want more info on what i did, i'd be glad to help.
here are some pics, sorry v bad Q....
I don't seem to see any pics?...
Ooops...
here you go
Seems good to me- as long as it all works ok then its a good job.
Always been interesting in making my own adapters/cables but have never tried. Perhaps I should give it a go!
sh500 said:
Hi all,
As per subject...
Anyone know if such as cable is available?
I was planning on getting the new 3-1 Adaptor for the TYTN to make use of the 3.5mm jack and charging feature in my car.
The thing is, the cable for this adaptor is very short and cannot be hidden easily when in the car. So, I was thinking of using an extension cable of some sort, so the adaptor could be more easily hidden elsewhere under the centre console.
Many thanks.
Click to expand...
Click to collapse
Any news on that extension cable yet; is it available?
i brought one of these and successfully lengthened it with an old peice of printer cable (only multi core cable i had to hand)
i then used an off the shelf diy project box to hide the junction in.
worked very well, but i have since changed to a bluetooth car kit.
the soldering was a little small and working out which wire was which was a bit of a pain, but all in all only took an hour or so to sort out. probably worth it.
(AFAIK my dad is still using the one i adapted.)
sorry to put old post on top !! but own a dimaond and just buy a touch HD !
i a m looking for this kind of cable !!
If someone have info !!
where to buy for exemple ?
thanks in advance !!
how about extending the power cable? seems like that would be easier.
3in1 11 PIN ExtUSB Earphone Handsfree Adapter for HTC
Other option: http://cgi.ebay.com/3in1-11-PIN-Ext...AU_MobilePhoneAccessories&hash=item3cabfd9d0b
Hi together,
ive asked me if it is possible to use an adapter for 1x micro usb (plug) -> 2x micro usb (jack).
Could the phone handle 2 USB devices at the same time?
Maybe then it is possible to use the HDMI output and the USB host parallel?
For example to use an TV as screen and an HDD as the source for a movie.
This would be nice.
Thanks in advance.
macc
When the connector is used for HDMI I doubt it can be used as USB at the same time, I'n sorry.
Maybe in a few months cyanogenmod provides a hack, if there will be an dual adapter soon.
We will see. Thank you.
macc
The hardware needs to allow this if it'd become possible. You need a really smart USB dongle that knows how to split the HDMI output from the USB output.
Sounds a little too difficult to ever happen.
Hmm thats right. I think i still dream xD
But thank you.
Sent from my GT-I9100 using Tapatalk
it is not possible. because as stated on this forum many times before, the type of usb connection is determined by the resistor between pin 4 and 5 of the micro usb connector. the strength can tell the phone, that there is either a charger, a pc connection, car kit, jig, usb otg or mhl connection present.
and i believe, this is an important thing to keep in mind for so many things:
for instance, why the original car kit triggers car mode and generic car charging cables don't or why not just any micro usb male to usb a female will work as a otg cable or why flashing should be done with the original usb cable...
so if you were to buy or build a micro usb hub, since it has no resistor in the very plug that connects to the phone, it cannot be used for anything but charging and quite frankly, i wouldn't connect more than one charger to the phone.
however, if you want to use your phone for presentations or watching movies and still be able to use it, get a bluetooth keyboard and mouse or a bluetooth presenter or do it the other way around and use a usb input device and transfer your media using allshare. everything else is physically impossible, so neither CM nor XDA can do anything about it. the only device that can do what you want is the new motorola. it has a separate micro usb and micro hdmi port and a docking station, so you can use it as a full notebook.
Thats obvious. Thank you.
macc
Hi all
I have a standard Samsung Galaxy SIII I9300. It is not rooted and I don't see the point in rooting it,as it is quick, reliable and if I'm not fooling around with it all day, the battery can last up to 2 days!!
But there is one thing I'd like to know how to do, if it is possible to do.
I want to be able to play music and alarm sounds through the micro USB port when the USB cable is connected instead of only through the 3.5mm jack.
I am going to be building a dock station with built in speakers. The Micro USB cable will charge the phone and the data wires will go to the speaker.
Will this work?
And if not, how can I make it work?
Hi!
I need your help!
I want to make a docking station in the car,
to connect the tablet(Huawei IDEOS S7 Slim) as a navigator in the car and the power(and usb-host, and others) was a 10pin connector
You know the pinout in 10-pin connector?
View attachment 1469888
Thanks!
P.S.Sorry for the english, I'm from Russia.
Same idea...
Taifunfly said:
usb-host
You know the pinout in 10-pin connector?
View attachment 1469888
Click to expand...
Click to collapse
I have same idea. So far I find out that S7 slim is not USB OTG capable (means it could be slave but not master in USB connections). Maybe there is the way to use some software to make S7 to act as a host since it have power on USB connector to supply usb flash.
Regarding 10 pin connector I couldn't find any info accept info on docking devices... According to that information: 10 pin connector is used for keyboard etc. Maybe it have digital audio and video out but you need to make some DA converter etc. cause I tested every pin with others and find out that there is no analog signals outputs (for audio).
I think that those information helped (to gett you on the right track) but I also like to hear
some opinion on the subject from experience members...
You have some other thread for docking (it's what 10 pin connector is) so you can read those.
http://forum.xda-developers.com/showthread.php?t=881565
I've read that some of the usb type C to 3.5 jack adapter are working now with a proper DAC, but I can't find a splitter that works for our HTC's or even for Pixel 2. People mention dongles made by certain companies, but I head to their websites and there's nothing available...
Can anyone help me find a viable splitter to charge and use headphones at the same time? I'm getting desperate, to be honest...
Thanks!
I have also tried several usb type c hubs but could not find one that works with htc headphones unfortunately.
I ended up buying an Bluetooth receiver to plug my headphones into when I need to charge too.
Not ideal but it works for me
mrew42 said:
I ended up buying an Bluetooth receiver to plug my headphones into when I need to charge too.
Not ideal but it works for me
Click to expand...
Click to collapse
Hey, that doesn't sound bad to me. I've never tried anything like that, though. Could you send me a link to your receiver or tell me any reference to start searching? Thanks in advance!
Erjimipey said:
Hey, that doesn't sound bad to me. I've never tried anything like that, though. Could you send me a link to your receiver or tell me any reference to start searching? Thanks in advance!
Click to expand...
Click to collapse
HIFI Bluetooth 4.1 Audio Transmitter & Receiver, Lenuo 2 in1 Wireless Music Adapter for TV / Home Stereo System Headphones Speakers MP3 / MP4 iPhone and More https://www.amazon.co.uk/dp/B06XRM8GXD/ref=cm_sw_r_other_apa_2ePXAbY8J5FFD
Look for a Bluetooth Receiver that supports wired headphones, i.e. it has a 3.5mm audio out socket.
Sent from my HTC U Ultra using Tapatalk
Checking that out as we speak. Thanks mate!
Hi guys,
still trying to figure this out. I hope you can help me with this idea. All I want is charge and use headphones at the same time :
If I plug this hub (or similar one) to my U Ultra's usb port https://m.es.aliexpress.com/item/32846535696.html?trace=wwwdetail2mobilesitedetail&productId=32846535696&productSubject=USB-C-Hub-USB-C-HDMI-Ethernet-Adapter-for-Macbook-Pro-Thunderbolt-3-Type-C-Hub
And then use this adapter (with DAC integrated) into the usb c of the hub: https://m.es.aliexpress.com/item/32832480232.html.
Will it work? Or the DAC needs to be placed exactly in the usb out of the phone? I'd really appreciate the help.
For these hubs to provide charging you need to connect the charger in the type c port of the hub which is marked with the lightning sign. To connect the 3.5 mm adapter you will need another adapter from usb type a male to type c female. Such adapters exsist but when i tried to connect the htc type c headphones via the hub and such adapter they were simply not detected by the phone so i doubt that the 3.5mm adapter will also work in such configuration.
neptun2 said:
For these hubs to provide charging you need to connect the charger in the type c port of the hub which is marked with the lightning sign. To connect the 3.5 mm adapter you will need another adapter from usb type a male to type c female. Such adapters exsist but when i tried to connect the htc type c headphones via the hub and such adapter they were simply not detected by the phone so i doubt that the 3.5mm adapter will also work in such configuration.
Click to expand...
Click to collapse
Thanks for the info, mate!
If I decided to go for Bluetooth earphones... Any will do, am I right? No DAC thing to be worried about, I guess...
Erjimipey said:
If I decided to go for Bluetooth earphones... Any will do, am I right? No DAC thing to be worried about, I guess...
Click to expand...
Click to collapse
That's it, exactly. Take any BT headset you like and can afford, they have the DAC already built in.