ok first post so i wont waste any time getting to my problem, how I caused it and what i have tryed to fix it.
i have a vibrant running 2.2, last night i tryed to root using aio toolbox not knowing it only worked for 2.1(my mistake).. so heres what happened it boot my phone into download mode and from there i tryed to install packages only to get a error about signature so i reboot my phone and tryed to use odin to downgrade only to realize that somehow i screwed up my phones ability to connect to pc, it charges but does not go in debugging massstorage etc, so from there i went back into download mode and tryed to reinstall packages only to get error about missing update.zip, i dont have superuser and dont know how to get the update.zip back without usbmode or superuser. ive tryed everything else, it will detect my wifes vibrant but not mine. i know its my phone not the pc/usb/drivers etc etc PLEASE HELP NEWBERT
just keep trying odin to get back to 2.1
my usb's dodgy aswell, charges and takes like an hour or 2 before it actually comes up on computer and phone saying its connected
i messed up mine the other day and it took me like 2 hours of trying to get it to connect to odin going through all 4 of my usb ports like 10 times each but it eventually did it so just keep trying
try different ways:
pull battery out and connect usb and open odin
hold vol up and down and push battery back in and it should go to download mode
or
leave battery in, open odin hold vol up and down and plug usb in and that should go to download mode
mine only works with the 2nd way for some reason, the 1st way seems to work for most people though
ive tryed this it will go into download mode but odin wont detect it, i think its something with my drivers on my phone. im completely new to this but i know it worked flawlessly untill i tryed to root, im not sure what went wrong besides i used aio toolbox intended for 2.1 on 2.2
Odd. I have never used the AIO Toolbox, never felt the need to, but yes, if you are able to get into download mode, but ODIN is not recognizing, it does sound like a driver issue.
You may want to uninstall/reinstall (here are the drivers, be sure to note the 32/64 tabs) LINK
Also, make sure you have the latest ODIN (check my going back to stock guide)
You might also want to make sure the pit/tar you have for JFD are good by checking the md5, I use hashtab to do this. (I realize you are not at that point yet).
Try rebooting your PC, pulling your battery and waiting a bit... trying different USB ports, be sure to remove other USB devices too before rebooting your PC (my ODIN will NEVER work with my webcam hooked up).
If that does not work, wonder if other drivers would help...
+1 follow above
- So the phone won't boot completely? That sux!
- If it did you could bluetooth the update.zip from her phone to urs.
.....but.......
- It automatically boots into recovery?thats odd
***How are you getting into Download mode?(the yellow triangle with android dude shoveling) Button combo maybe?
Related
So, I just got my phone back from Samsung for this issue. Start my newly returned phone up, it's running 2.2. I turn it off, hold volume buttons and plug in my USB cable - I get download mode instantly. I start up Odin 1.7, select the files and click start.
Nothing happens. Hangs up SetupConnection. I unplug the battery, then the USB cable, plug everything back in and I'm back at square one with this ****ing screen.
Last time I tried every single ****ing button combination posted on this website. I know my phone isn't hardware locked because I've never had a problem getting in to Download Mode before. Hell, I'd never had a problem with Odin not working properly before. What the hell is wrong? I have all the proper drivers installed. Why is this happening?
Now, Odin still sees my phone when I plug it in. If I click Start, sometimes it hangs on SetupConnection, sometimes it hangs on Initialization. I've read that you should still be able to flash while on this screen? Is this true? Either way, I think I'm ****ed again. Any help?
Also, I've read that maybe a jig will help get me in to download mode? Where can I buy a jig from?
you can go to stock jfd from that screen, it acts like download mode.
Once on jfd, download mode will work fine.
try the files in my going back to stock... also make sure to remove any other usb components (they can cause odin to hang).
I love you.
Something must be wrong with the files on my desktop, or perhaps the other USB cable I'm using is ****ed.
This is a bit embarrassing. For some reason I can't get root. I can get in to recovery and select reinstall packages, but every time it boots right back in to the OS. Any hints? Never had this issue before.
EDIT: So it looks like I have Superuser installed but since I can't get into Clockwork I can't flash any roms. What's going on? I can't find any other links where people couldn't get in to Clockwork.
EDIT2: Well, I installed ROM Manager and used it to "flash" CWM. Reinstall Packages worked this time it seems. Weird. Anyway, thanks for the help!
Cool, glad you were able to get it all sorted.
I'll tell the whole story so you can see how I got to where I was. jump to the end:
-Running bionix 1.3.1 used rom manager to get the new cm7.1.01. Backed up my rom.
-Google apps didn't install (even though I clicked it in rom manager) so I installed gapps through rom manager.
-Gapps installed but couldn't download anything from the appstore Error. I tried many things for a day and decided to restore my old rom with rom manager.
-Vibrant screen for over an hour. Rebooted into download mode and tried to go back to stock (T959UVJI6) with odin.
-Odin had been stuck at "File analysis.." for about 30 minutes so I decided to reboot my phone (this may have been a mistake?).
-When I rebooted it, it was in softbricked mode (phone ! computer).
-I've spent the better part of the day trying different hold and vol+power release power second black screen. (Exhausted forum.cyanogenmod.com/topic/6998-howto-recover-from-a-soft-brick-on-your-vibrant/)
-adb can't find the device (although it does show up in odin when I plug it in). Droid explorer can't find the device either.
Am I out of options? I live in canada so I can't just go to a t-mobile store and play stupid.
Thanks, hopefully something comes up that searching hasn't uncovered.
Tried this?
http://forum.xda-developers.com/showthread.php?t=751210
Doing the jig method right now didn't have three 100kohm lying around so I tried 220 and 320 but those didn't work. I'll try 300 tomorrow.
Jig is for phone to go into download mode. your phone is already recognized by odin when you plug it in right? then you don't need a jig. Just try to flash jfd again. you can even Odin it from phone computer screen if Odin recognizes your phone.
Sent from samsung vibrant
Persistence paid off, not sure if it was trying different roms different usb ports or reinstalling drivers but eventually odin worked. I would say that there isn't enough people saying the the computer ! phone doesn't mean soft bricked. That it could still be in download mode. Thanks.
I'm pretty sure i have attempted every solution on here (XDA) and elsewhere to troubleshoot my problem. I am hoping it is obvious, but i've put hours into this and i could really use some help!
My tablet is (or was) a Verizon 4G LTE Galaxy 10.1
I had successfully rooted it when i first got it using Odin...i flashed a ROM...can;t remember which one (obviously a wrong one) and ever since it has been rather temperamental.
Over the course of the past week i have been to APX and back... Heimdall (which i am pretty sure i am not doing correctly) to attempting to flash firmware..stock roms etc...
I don;t know whether it is a driver issue, or if i need a stock rom or to flash firmware....but here is where i am at now.
If i try to power up normally...the Samsung galaxy tab logo bootlader flashes for a sec or two...the screen then either goes black...and repeats a few times...or sometimes it flashes the logo and the backlight stays on until i turn it off.
(Seems to be a fairly common problem)
If i hold the volume up and power together...i can get to the Odin download screen with the flashing droid and the midget droid that appears to be walking away from a trash can.
HOWEVER, when i plug the tab into my laptop (windows 7 x64) (i also have access to a (windows 7 x86) and my girlfriends xp machine. I've tried on all mostly on my x64 machine.
Heres the thing.
When i power down...sometimes just pressing the power button once or twice...sometimes, while off i hold the volume down button for a few sec..and all of a sudden the comp reads the device and i can get open ODIN...get the yellow COM thing...but never seem i always get the same error message...can not open/find com/port...
so i can get into odin on my comp with a black screen on my device...or i can get to download mode on my device and my machine wont recognize it.
I seem to have inherited a little bit of everyones problems on here...
Please tell me that there is hope for my tablet...please help? I'm sure you can imagine my frustration. TY.
joshualectric said:
I'm pretty sure i have attempted every solution on here (XDA) and elsewhere to troubleshoot my problem. I am hoping it is obvious, but i've put hours into this and i could really use some help!
My tablet is (or was) a Verizon 4G LTE Galaxy 10.1
I had successfully rooted it when i first got it using Odin...i flashed a ROM...can;t remember which one (obviously a wrong one) and ever since it has been rather temperamental.
Over the course of the past week i have been to APX and back... Heimdall (which i am pretty sure i am not doing correctly) to attempting to flash firmware..stock roms etc...
I don;t know whether it is a driver issue, or if i need a stock rom or to flash firmware....but here is where i am at now.
If i try to power up normally...the Samsung galaxy tab logo bootlader flashes for a sec or two...the screen then either goes black...and repeats a few times...or sometimes it flashes the logo and the backlight stays on until i turn it off.
(Seems to be a fairly common problem)
If i hold the volume up and power together...i can get to the Odin download screen with the flashing droid and the midget droid that appears to be walking away from a trash can.
HOWEVER, when i plug the tab into my laptop (windows 7 x64) (i also have access to a (windows 7 x86) and my girlfriends xp machine. I've tried on all mostly on my x64 machine.
Heres the thing.
When i power down...sometimes just pressing the power button once or twice...sometimes, while off i hold the volume down button for a few sec..and all of a sudden the comp reads the device and i can get open ODIN...get the yellow COM thing...but never seem i always get the same error message...can not open/find com/port...
so i can get into odin on my comp with a black screen on my device...or i can get to download mode on my device and my machine wont recognize it.
I seem to have inherited a little bit of everyones problems on here...
Please tell me that there is hope for my tablet...please help? I'm sure you can imagine my frustration. TY.
Click to expand...
Click to collapse
Have you tried rhis method
http://rootzwiki.com/topic/7718-romleakodineg01-factory-stock-odin-image-vzw-lte-tab-101/
Sent from my GT-P7510 using Tapatalk
...
Thanks for the quick reply. I think i did try this at one point...the problem still stands...when i am in odin dl mode on my tab...the com tab wont turn yellow and comp wont read my device.
If i do it the other way....with a black screen...it wont be able to communicate or find the port. ...but ill try again right now.
Nope....epic fail. There has to be a solution, right?
As long as you can get into download mode you should be able to fix it. Most likely the issue is not your tab but the drivers on your computer.
I spent the better part of a day frustrated trying to go from the leaked 3.2 to official 3.2 having issues similar to you with Odin. Funny thing is for me the PC somehow ended up not recognizing the tab on the USB port I used to flash on but would on others so I simply swapped Ports and continued. Little did I realize that although things seemed okay that issue was a symptom and Odin was now flashing corrupted info onto the tablet.
A simple reboot of the PC fixed things for me. That you have tried other machines though is worrisome. Still there's a chance it still is a driver issue so I would check drivers on the PC and perhaps install kies if you don't have it to see if the drivers with kies help.
Since you're on the Verizon tab flash back to stock 3.1 and flash stock recovery. Then let all the OTA updates run. After that all you need to do is flash cwm and Pershoots kernel along with superuser to be rooted. There is no better ROM for our Verizon tab than this and all wifi ROMs are incompatible with it.
Still, no luck. When i am in download mode on my tab....my computer doesn't recognize it. When I just power up and and plus it in, the screen goes black but the computer sees the device as well as ODIN. However sometimes it is recognized as APX and sometimes it is recognized as a Samsung android device... usually with one or two driver errors.
So, it seems obvious that it would be a driver issue... i've tries kies, and as many variations of drivers i can find.,.. when in APX mode i try to flash using the nvflash method in cmd or heimdall, otherwise i try ODIN and it seems to be successful until the "setup connection" point.
Is there a way (if it is even something i should do ) to get drivers on my device in its current state?
Im at a loss...i know this thing can be resurrected...everything just seems so backwards. Any thoughts?
I know that this is a very basic question, but do you have USB Debugging enabled?
George
No way to check now, as he says the tablet doesn't boot any more.
It sounds like a driver issue for sure, and to be clear here the ONLY requirement that I know of when flashing with odin on the TABLET end is for it to be in download mode waiting for usb BEFORE being plugged in. So when I say driver issue Im talking about on the PC side here. Have kies installed just to get the drivers, fire up odin and get the tab into download mode while unplugged. Plug it in and watch odin to see if the com port status lights up. If not swap usb port and repeat. Do not use a hub and ypu may want to remove unnecessary usb devices too just to see.
I tried to install CM 7 on my Samsung vibrant, but it bootlooped and is now stuck on "samsung vibrant" screen. If I plug it in after pulling the battery to turn it off it never shows the battery screen, just a loading symbol. Can give more info, just not now.
Thanks
-Adam
Boot back into recovery and reflash CM7 again. This is normal for it to bootloop on install b/c of the CWR mismatch.
Froyo Bootloaders-> Volu +/- and Power, See Vibrant, release power
Gingerbread Bootloaders -> Volu- and Power
vol- and pwr got me to download mode, but I can't get Odin to work right. How do I get to recovery?
EDIT: I think my computer and phone are not communicating, because neither Odin, Heimdall or OCUB are even registering its connection, although my computer tries to install drivers every time I plug it in.
Sounds rudimentary and I am sorry for saying it but this has worked for many a user.
Try a different USB port or cable. Seen it happen quite a few times where they switch ports and everything works just fine.
If you can get into download mode then you should be able to get Odin working eventually.
Okay.
After some messing with Odin, my phone is still not working. OneClickUnBrick is failing, thinks that I don't have Heimdall installed. Do you have a tar that you know is good?
Go to the Dev section and download the AIO Toolbox. It has Odin 1.8, all the drivers, the pit/tar files to get you back to 2.1 then to CM again. Links in toolbox are live again. Don't forget to download the .net files to.
Once you're back on stock and everything is running good again you may want to follow this guide...
http://forum.xda-developers.com/showthread.php?t=1307637
...Although it says it's for Miui, it's the same steps for CM7. It'll take you step-by-step through the installation process.
Sent from my SGH-T959 (Samsung Vibrant)
Thanks guys. The AIO Toolbox has not installed yet but it looks promising. I will edit when it finishes.
Also, has Cyanogen made a stable ICS Rom?
It worked, thanks guys! this would have taken way longer -- and maybe never worked -- if no one had stopped to help a noob.
-Adam
I was on Miui rom, but I wanted to go and try Simpley Honey, so I went to CWM and wiped everything like it said, and I accidently formated the boot too. Is this why I'm stuck at the screen? i tried everything` Odin,Heimdall,Aio toolbox and all drivers for vibrant,but pc dont recognize my phone and there are only show <unknown device>
PLEASEEEEEE HELP TO FIX MY VIBRANT
Couple of things to try.
First, if you want to Odin, then I usggest going into your device manager on your PC and uninstalling your drivers. Then reinstall them manually of with the Toolbox.
Second, (Rule #1-Always make a back up)- Hopefully you made a nandroid back up of your MIUI that you were on. If so, you should be able to restore that and then wipe properly.
Third, if you can get into Recovery and you don't have a back up, then try to flash a ROM (2.3.x or higher since you were on MIUI) and see if that gets you back up and running.
Pretty sure that if you wiped Boot.img your phone is still recoverable. It isn't like you wiped out the bootloader or anything. Those are not touchable from CWR, so don't fret that part.
i uninstalled all drivers then installed again but odin dont recognize my phone(unknown device) in download mode,and i can not acces to CWM(((
do uninstall those drivers again and just download and install samsung kies mini it will automatically recognize and install drivers for you.. hope this will help you...JFD by odin will be the best way after that...
NB:for future reference---
always remember two things before flashing any rom...
** do nandroid backup
** get back to stock by odin then proceed any rom you want...
Haha, I did this before (about 2 weeks ago). I just placed it in download mode, then flashed back to stock using ODIN.
I tried everything but pc dont recognize my vibrant(((
dont freak out man, like everybody has said you did not brick your phone. when you click format boot, you only wipe the boot media (the startup image/video). you're boot-loaders are still in tact. this is all about getting your pc to recognize your phone. try to connect on another computer and try different variations of connecting to the computers, try a different usb port. Once I thought I bricked my vibrant as in I couldn't get into download mode or anything. I stupidly unplugged it while it was installing factory.rfs on odin, I thought it was stuck. Nothing would come up with any button combo pressed. then nine hours later and a change of usb ports, I got it into download mode an odined to stock.
but ive already tried it in many computers and usb ports,but still no success(((