Need Help, I just flashing using KDZ for Ginger Bread Rumania Official.
In the middle way, KDZ is stuck and my O1 in Emergency Mode. I just wait untill Finnish. But not yet finish..
This is the log:
[16:45:54:075] : =============================================
[16:45:54:075] : Log is started on 03.07.2011, at 16:45:54:075,
executable: D:\Master\Android\Cara Flash ROM\KDZ_FW_UPD_EN\KDZ_FW_UPD.exe (ProcID: 0x00000b70),
compile time : Dec 8 2010 09:19:37
[16:45:54:075] : Version :
[16:45:54:077] : Get Usb Port
[16:45:54:102] : rsi.strFriendlyName=Agere Systems HDA Modem
[16:45:54:102] : Remove Agere Systems HDA Modem
[16:45:54:102] : rsi.strFriendlyName=LGE Android Platform USB Serial Port (COM5)
[16:45:54:102] : FriendlyNameList[iii].szFriendlyName=LGE Android Platform USB Serial Port
[16:45:54:102] : rsi.strFriendlyName=LGE Android Platform USB GPS NMEA Port (COM6)
[16:45:54:102] : Remove LGE Android Platform USB GPS NMEA Port (COM6)
[16:45:54:102] : rsi.strFriendlyName=ZTE Service Port FFF1 (COM14)
[16:45:54:102] : Remove ZTE Service Port FFF1 (COM14)
[16:45:54:102] : rsi.strFriendlyName=ZTE Voice Port FFF1 (COM15)
[16:45:54:102] : Remove ZTE Voice Port FFF1 (COM15)
[16:45:54:102] : rsi.strFriendlyName=ZTE Diagnostics Port FFF1 (COM16)
[16:45:54:102] : Remove ZTE Diagnostics Port FFF1 (COM16)
[16:45:54:102] : rsi.strFriendlyName=ZTE GPS Port FFF1 (COM17)
[16:45:54:102] : Remove ZTE GPS Port FFF1 (COM17)
[16:45:54:102] : WM_COPYDATA ¸Þ½ÃÁö º¸³¿ 1 - COM5
[16:45:54:102] : Port = COM5
[16:45:54:114] : >> DIAG_STATUS_F FAILED
[16:45:54:119] : >>Get Model Name [DIAG_VERNO_F]
[16:45:54:120] : strModel = P500
[16:45:54:120] : Read NV item: 71 NV ITEM 71 [71]
[16:45:54:121] : CSW
[16:45:54:121] : Banner : CSW
[16:45:54:121] : WM_COPYDATA ¸Þ½ÃÁö º¸³¿ 0 - P500
[16:45:54:132] : Write NV item:9028 NV ITEM 9028
[16:45:54:132] : 9028 - NV_DONE_S Item
[16:45:54:232] : _DloadMode()
[16:45:54:238] : ¸Þ½ÃÁö º¸³¿ TYPE_WPARAM_CHANGE_DLOAD 4
[16:45:54:238] : >>Change Offline Mode [DIAG_CONTROL_F/Mode = 1]
[16:45:54:249] : >>Change Dload Mode [DIAG_DLOAD_F]
[16:45:54:250] : WM_COPYDATA ¸Þ½ÃÁö º¸³¿ 3 - DLOAD
[16:45:54:250] : DIAG_DLOAD_F DLOAD_RESET_F do not wait for response
[16:45:54:250] : WM_COPYDATA ¸Þ½ÃÁö º¸³¿ 3 - Close Port
[16:45:54:250] : Close Port<<
[16:46:34:251] : EMERGENCY Booting Mode
[16:46:34:251] : >>Get Model Name in Emergency Mode [DLOAD_VERREQ_F]
[16:46:34:262] : BS/P500/7D
[16:46:34:262] : WM_COPYDATA ¸Þ½ÃÁö º¸³¿ 0 - P500
[16:46:34:262] : >> GET DLOAD COMM MODE
[16:46:34:263] : [GetCommMode] Communication mode : 2
[16:46:34:263] : Pre Nand Download
[16:46:34:263] : >>Set Trusted Mode [DLOAD_NAND_SEC_MODE] sec_mode = 1 (1=trusted 0=NonTrusted)
[16:46:34:263] : WM_COPYDATA ¸Þ½ÃÁö º¸³¿ 3 - TRUSTED MODE
[16:46:34:264] : [COM5] >>NandFlashInitWithFile(PARTITION TBL)
[16:46:34:264] : WM_COPYDATA ¸Þ½ÃÁö º¸³¿ 3 - INIT PARTITION TBL
[16:46:34:366] : ¸Þ½ÃÁö º¸³¿ TYPE_WPARAM_WRITE_TO_SDRAM 3
[16:46:34:366] : [COM909520946] ¸Þ½ÃÁö º¸³¿ TYPE_WPARAM_WRITE_AMSS 15
[16:46:34:366] : [COM5] >>NandFlashInitWithFile(AMSS MODEM HEADER)
[16:46:34:371] : WM_COPYDATA ¸Þ½ÃÁö º¸³¿ 3 - INIT AMSS MODEM HEADER
[16:46:34:383] : [COM909520946] >>Dl_AsyncWrite()
[16:46:34:383] : >> AMSS FLASHING ...
[16:46:34:386] : ¸Þ½ÃÁö º¸³¿ ProgreassiveBar Init wParam TYPE_WPARAM_PROGRESSIVE_POS=5 lParam(pos)=0 nResult=0
[16:46:34:386] : Sending Pkt Seq : 0
[16:46:34:386] : Sending Pkt Seq : 1
[16:46:34:386] : Sending Pkt Seq : 2
[16:46:34:386] : Sending Pkt Seq : 3
[16:46:34:386] : Sending Pkt Seq : 4
:
:
:
[16:47:50:926] : Sending Pkt Seq : 50158
[16:47:50:926] : Sending Pkt Seq : 50159
[16:47:53:933] : RX Timeout : 3.0 seconds
[16:47:53:933] : RX TIMEOUT
[16:47:56:944] : RX Timeout : 3.0 seconds
[16:47:56:944] : RX TIMEOUT
[16:47:59:950] : RX Timeout : 3.0 seconds
[16:47:59:950] : RX TIMEOUT
[16:47:59:950] : [COM909520946] ERROR Dl_AsyncWrite() TYPE_LPARAM_UPGRADE_ERROR_WRITE_TO_FLASH
[16:47:59:950] : WM_COPYDATA ¸Þ½ÃÁö º¸³¿ 3 - Close Port
[16:47:59:950] : Close Port<<
[16:47:59:950] : TYPE_WPARAM_UPGRADE_ERROR
[16:47:59:950] : ¸Þ½ÃÁö º¸³¿ - TYPE_WPARAM_UPGRADE_ERROR Error Code = 500
[16:48:00:007] : Log finished
Click to expand...
Click to collapse
After that, I unplug the USB, My O1 still emergency mode. I can't Power ON or OFF, I just plug out the battery.
After that, My phone can't Power ON or Communication with my Computer.
Somebody can help me?
Thnx anyway.
osana412 said:
I can't Power ON or OFF, I just plug out the battery.
After that, My phone can't Power ON or Communication with my Computer.
Click to expand...
Click to collapse
Never ever do this. In emergency mode it is still recoverable. If you cannot power on the phone, well... you have a nice brick. Unless you have a JTAG (if you wonder WTH it is then you don't ) just head to nearest LG service center to have the PCB changed
Oh no.... It is true?
No other way to fix it?
osana412 said:
Oh no.... It is true?
No other way to fix it?
Click to expand...
Click to collapse
No. LG service is best option. JTAG costs half the phone.
Never loose the yellow emergency mode. If the phone is in warranty just tell them u were updating through PC suit and now its dead. (Don't say bricked)
Sent from my LG-P500 using XDA Premium App
ok2... ic..... I will tell them like that..
What is LG Service will do with my phone? change the PCB or what? I'm very curious..
Does emergency mode yellow screen still appears or not, if it does you still have hope you can flash froyo kdz file onto the phone many tutorials are there that can help
Sent from my LG-P500 using XDA App
osana412 said:
ok2... ic..... I will tell them like that..
What is LG Service will do with my phone? change the PCB or what? I'm very curious..
Click to expand...
Click to collapse
Yes they change the PCB you get a new imei.
Sent from my LG-P500 using XDA Premium App
Emergency mode= back button+vol up+power
Good luck.
No. My false is unplug the battery.. and my phone is death...
So I decided to Root my Android Optimus One LG-P504 and that went over well. Soon after I wanted a faster phone, so I attempted to put the Oxygen custom ROM on it, and messed up somewhere. I Then began to try and fix it using a few different methods, none have worked. I am now sitting with my phone completely unusable and sitting in Emergency Mode.
Solutions I've Tried:
_____________________________________
KDZ_FW_UPD.exe and I get this far
[
[01:43:20:203] : =============================================
[01:43:20:203] : Log is started on 14.03.2012, at 01:43:20:203,
executable: F:\Download\KDZ_FW_UPD_EN\KDZ_FW_UPD.exe (ProcID: 0x00000cf8),
compile time : Sep 13 2010 11:34:51
[01:43:20:203] : Version :
[01:43:20:234] : Get Usb Port
[01:43:20:234] : rsi.strFriendlyName=LGE Bluetooth TransPort (COM4)
[01:43:20:234] : Remove LGE Bluetooth TransPort (COM4)
[01:43:20:234] : rsi.strFriendlyName=LGE Android Platform USB Serial Port (COM6)
[01:43:20:234] : FriendlyNameList[iii].szFriendlyName=LGE Android Platform USB Serial Port
[01:43:20:234] : WM_COPYDATA ¸Þ½ÃÁö º¸³¿ 1 - COM6
[01:43:20:234] : Port = COM6
[01:43:20:250] : UNKNOWN : Req(12) -> Rsp(13)
[01:43:20:265] : UNKNOWN : Req(12) -> Rsp(13)
[01:43:20:281] : UNKNOWN : Req(12) -> Rsp(13)
[01:43:20:281] : >> DIAG_STATUS_F FAILED
[01:43:20:296] : >>Get Model Name [DIAG_VERNO_F]
[01:43:20:312] : BAD CONN MODE : Req(0) -> Rsp(3)
[01:43:20:328] : BAD CONN MODE : Req(0) -> Rsp(3)
[01:43:20:343] : BAD CONN MODE : Req(0) -> Rsp(3)
[01:43:20:359] : BAD CONN MODE : Req(0) -> Rsp(3)
[01:43:20:375] : BAD CONN MODE : Req(0) -> Rsp(3)
[01:43:20:390] : BAD CONN MODE : Req(0) -> Rsp(3)
[01:43:20:390] : FAIL (No Phone)
[01:43:20:390] : GetModelName() Operation Failed Check Diag CMD
[01:43:20:390] : EMERGENCY Booting Mode
[01:43:20:390] : >>Get Model Name in Emergency Mode [DLOAD_VERREQ_F]
[01:43:20:406] : BS/P504/7Dd\Tail.exe
[01:43:20:406] : WM_COPYDATA ¸Þ½ÃÁö º¸³¿ 0 - P504
[01:43:20:421] : DLOAD_NAK_F reason_msb = 3, reason_lsb = 3
[01:43:20:421] : [ DLOAD ERROR ] : NAK_INVALID_LEN
[01:43:20:437] : DLOAD_NAK_F reason_msb = 3, reason_lsb = 3
[01:43:20:437] : [ DLOAD ERROR ] : NAK_INVALID_LEN
[01:43:20:453] : DLOAD_NAK_F reason_msb = 3, reason_lsb = 3
[01:43:20:453] : [ DLOAD ERROR ] : NAK_INVALID_LEN
[01:43:20:453] : NV Write Fail : NV ITEM 9028(9028)
[01:43:20:562] : >> GET DLOAD COMM MODE
[01:43:20:578] : [GetCommMode] Communication mode : 2
[01:43:20:578] : Pre Nand Download
[01:43:20:578] : >>Set Trusted Mode [DLOAD_NAND_SEC_MODE] sec_mode = 1 (1=trusted 0=NonTrusted)
[01:43:20:578] : WM_COPYDATA ¸Þ½ÃÁö º¸³¿ 3 - TRUSTED MODE
[01:43:20:593] : [COM6] >>NandFlashInitWithFile(PARTITION TBL)
[01:43:20:593] : WM_COPYDATA ¸Þ½ÃÁö º¸³¿ 3 - INIT PARTITION TBL
[01:43:20:625] : ¸Þ½ÃÁö º¸³¿ TYPE_WPARAM_WRITE_TO_SDRAM 3
[01:43:20:625] : [COM1783997892] ¸Þ½ÃÁö º¸³¿ TYPE_WPARAM_WRITE_AMSS 15
[01:43:20:625] : [COM6] >>NandFlashInitWithFile(AMSS MODEM HEADER)
[01:43:20:625] : WM_COPYDATA ¸Þ½ÃÁö º¸³¿ 3 - INIT AMSS MODEM HEADER
[01:43:20:640] : [COM1783997892] >>Dl_AsyncWrite()
[01:43:20:640] : >> AMSS FLASHING ...
[01:43:20:640] : ¸Þ½ÃÁö º¸³¿ ProgreassiveBar Init wParam TYPE_WPARAM_PROGRESSIVE_POS=5 lParam(pos)=0 nResult=0
[01:43:20:640] : Sending Pkt Seq : 0
[01:43:20:640] : Sending Pkt Seq : 1
[01:43:20:640] : Sending Pkt Seq : 2
[01:43:20:640] : Sending Pkt Seq : 3
[01:43:20:640] : Sending Pkt Seq : 4
[01:43:20:640] : Sending Pkt Seq : 5
[01:43:20:640] : Sending Pkt Seq : 6
[01:43:20:640] : Sending Pkt Seq : 7
[01:43:20:640] : Sending Pkt Seq : 8
[01:43:20:640] : Sending Pkt Seq : 9
[01:43:20:656] : Dl_AsyncWrite - ErrNo(45), Addr(0x00004800), NandErrNo(0x04)
[01:43:20:656] : [COM1783997892] ERROR Dl_AsyncWrite() TYPE_LPARAM_UPGRADE_ERROR_WRITE_TO_FLASH
[01:43:20:687] : WM_COPYDATA ¸Þ½ÃÁö º¸³¿ 3 - Close Port
[01:43:20:687] : Close Port<<
[01:43:20:687] : TYPE_WPARAM_UPGRADE_ERROR
[01:43:20:687] : ¸Þ½ÃÁö º¸³¿ - TYPE_WPARAM_UPGRADE_ERROR Error Code = 4008
[01:43:20:703] : Log finished
]
And then get this error
Upgrade Error
WParam : 100
LParam: 4008
_________________________________________
Clearly The fastboot will not work for me since I am stuck in the Yellow Emergency Mode screen.
_________________________________________
Hardboot is not working
_________________________________________
Does anyone have a possible solution for this?
Dude you have bricked your cell,go to LG gallery..
handryg555 said:
Dude you have bricked your cell,go to LG gallery..
Click to expand...
Click to collapse
Dang, Thanks guess ill have to take it in later this week. So will i be paying for it?(If you know)
if u have warranty thn they will do it free of cost...
just tell them u left the phone for charging and slept in the night and this happend when u saw it after u woke up...
Ashkore said:
Dang, Thanks guess ill have to take it in later this week. So will i be paying for it?(If you know)
Click to expand...
Click to collapse
no, I guess, if it is under warranty...but don't let them know, what u were exactly trying to do (rooting and all) else the warranty will get void...
tell them that, this was what u saw, when u woke up today n switched on the phone... u may get lucky enough...
Edit: oops sorry...exactly the same thing already replied...
Well, I had the same problem and this is what I did:
1. Install the LG Drivers for the phone.
2. Remove the SD Card if you have one.
3. Put the phone into EMERGENCY MODE!!
4. Set the Type to '36QCT' and the PhoneMode to 'CS_EMERGENCY'.
5. Download the KDZ file. (V20E_00.kdz)
6. Launch the Software Update.
7. If this fails, retry this steps on a computer running Windows XP.
If I helped, please donate!
this might help u
http://androidforums.com/lg-optimus-one-p500/484017-story-my-wal-mart-family-mobile-phone.html
http://forum.xda-developers.com/showthread.php?t=1316514
Ezpanio said:
Well, I had the same problem and this is what I did:
1. Install the LG Drivers for the phone.
2. Remove the SD Card if you have one.
3. Put the phone into EMERGENCY MODE!!
4. Set the Type to '36QCT' and the PhoneMode to 'CS_EMERGENCY'.
5. Download the KDZ file. (V20E_00.kdz)
6. Launch the Software Update.
7. If this fails, retry this steps on a computer running Windows XP.
If I helped, please donate!
Click to expand...
Click to collapse
Thats V20E.dkz file, where did you get that? I could not seem to find the right firmware for my phone, none for America, I ended up just grabbing the UK one.
Hello, I shall do my best to shortly and concisely lay out my difficulties. (It was a bad decision to try to install a custom ROM on the Monday before finals)
I was looking to put a custom ROM on my phone, and was following this guide. I put CWM on my phone via this method. I had the ROM I wanted on my SD card. I boot into CWM, wipe the davlek cache like a good little boy, wipe the system (yikes), and select the .zip I want. Nope, status 7 error, abort! Heart racing slightly, I quickly Google and find a nice solution. Problem! When I reboot back into CWM... there is no CWM, and I'm stuck with the useless stock recovery mode that literally does nothing but show a picture of a dead android on its side.
I'm having issues with the offline installer. I've tried both the automated method and doing it myself but really nothing seems to be getting around the fact that my computer doesn't want to talk to my windows 8 computer, or my friend's windows 7 computer.
Here's some log output:
Code:
16:09:25 : [C:\LGMobileUpgrade] Try to delete folder
16:09:25 : RemoveDirectory1 Error(2):C:\LGMobileUpgrade
16:09:25 : Start Date : 2014-03-10 16:09:25
16:09:25 : ---------- QM Testmode ---------
16:09:25 : ***** Check Tool Version *****
16:09:25 : Tool version : 1.5.4.8
16:09:25 : UpgradeDLL version : 1.2.6.7
16:09:25 : Current Dir : C:\ProgramData\LGMOBILEAX\B2C_Client
16:09:26 : LGE USB Driver Version :
16:09:26 : Android PDLV Version :
16:09:26 : Android NDLV Version :
16:09:26 : ******************************************
16:09:26 : [C:\ProgramData\LGMOBILEAX\Phone] Try to delete folder
16:09:26 : RemoveDirectory1 Error(2):C:\ProgramData\LGMOBILEAX\Phone
16:09:26 : SetEmerModeAT()
16:09:26 : _IsConnectedPhone Call
16:09:35 : _IsConnectedPhone(0)
16:09:35 : 0 - NotConnected.
16:09:35 : 1 - Normal connect success
16:09:35 : 2 - Emergency connect success
16:09:35 : *****CheckOS Start********
16:09:35 : Microsoft_Windows7_Home Edition_
16:09:35 : *****CheckPCSyncPrograms Start*****
16:09:36 : PCSyncPrograms Not Found - OK and ready to upgrade
16:09:36 : Checking the connection with the cell phone...
16:09:36 : dwWaitResetTime(40000 ms)
16:09:37 : _IsConnectedPhone Call
16:09:44 : _IsConnectedPhone(0)
16:09:44 : 0 - NotConnected.
16:09:44 : 1 - Normal connect success
16:09:44 : 2 - Emergency connect success
16:09:45 : _IsConnectedPhone Call
16:09:52 : _IsConnectedPhone(0)
16:09:52 : 0 - NotConnected.
16:09:52 : 1 - Normal connect success
16:09:52 : 2 - Emergency connect success
16:09:53 : _IsConnectedPhone Call
16:10:01 : _IsConnectedPhone(0)
16:10:01 : 0 - NotConnected.
16:10:01 : 1 - Normal connect success
16:10:01 : 2 - Emergency connect success
16:10:01 : [009,400,102,102,102]The USB cable and your cellphone are not connected.\nPlease connect your phone and wait for connecting \nthe USB port for a while and press the [009,700,147,062,092]'Restart'[009,400,102,102,102] button.
16:10:11 : _IsConnectedPhone Call
16:10:11 : _IsConnectedPhone(0)
16:10:11 : 0 - NotConnected.
16:10:11 : 1 - Normal connect success
16:10:11 : 2 - Emergency connect success
16:10:11 : [009,400,102,102,102]The USB cable and your cellphone are not connected.\nPlease connect your phone and wait for connecting \nthe USB port for a while and press the [009,700,147,062,092]'Restart'[009,400,102,102,102] button.
16:10:17 : _IsConnectedPhone Call
16:10:24 : _IsConnectedPhone(0)
16:10:24 : 0 - NotConnected.
16:10:24 : 1 - Normal connect success
16:10:24 : 2 - Emergency connect success
16:10:24 : [009,400,102,102,102]The USB cable and your cellphone are not connected.\nPlease connect your phone and wait for connecting \nthe USB port for a while and press the [009,700,147,062,092]'Restart'[009,400,102,102,102] button.
16:11:02 : _IsConnectedPhone Call
16:11:02 : _IsConnectedPhone(0)
16:11:02 : 0 - NotConnected.
16:11:02 : 1 - Normal connect success
16:11:02 : 2 - Emergency connect success
16:11:02 : [009,400,102,102,102]The USB cable and your cellphone are not connected.\nPlease connect your phone and wait for connecting \nthe USB port for a while and press the [009,700,147,062,092]'Restart'[009,400,102,102,102] button.
16:11:04 : Check Cancel button active..
16:11:04 : Check Cancel button active..
16:11:04 : !pUpgrade->StartProcessing ... PostMsg STEP_TYPE_ENV_ERROR
16:11:04 : Page_Error ºÎºÐÀÔ´Ï´Ù
16:11:04 : [011,700,147,062,092]LG Mobile Phone Software Update was canceled\n\n[009,400,102,102,102]To quit LG Mobile Phone Software Update, please press the [009,700,147,062,092]Exit[009,400,102,102,102] button below.
16:11:04 : OnStepMsg STEP_TYPE_ENV_ERROR delete m_pLGCyonUpdate
And screenshots attached.
Listed in Device Manager:
ADB Interface > Android Platform Sooner Single ADB Interface
Modems > LGE Android Platform USB Modem
> LGE Mobile USB Modem
> LGE Mobile USB Modem #2
Other Devices > Unknown device (I installed the fastboot drivers to this, had to get around the driver signature stuff)
Ports (COM & LPT) > LGE Android Platform USB Serial Port (COM7)
> LGE Mobile USB Serial Port (COM4)
> LGE Mobile USB Serial Port (COM6)
Universal Serial Bus Controllers > LGE Mobile Composite USB Device
> LGE Mobile Composite USB Device
Please help if you can. Thank you.
Hi not_so_optimustic, you could try this way: http://forum.xda-developers.com/showthread.php?p=50729855
Cheers. Good luck.
Sent from my LG P76020L-EUR-XX unlocked and rooted
BajoPrimate said:
Hi not_so_optimustic, you could try this way: http://forum.xda-developers.com/showthread.php?p=50729855
Cheers. Good luck.
Sent from my LG P76020L-EUR-XX unlocked and rooted
Click to expand...
Click to collapse
Thank you for the reply.
What happens: I hold power and volume up after plugging in. Immediately I get a "USB device no recognized" in a bubble in the bottom right. A second later I get the S/W screen. I put the battery in. Start the program. If I switch windows it hangs. It gives me this:
Code:
[R&D Test Tools Log File]
20:28:06 : Launching SW update
20:28:06 : Unpacking KDZ
20:29:00 : KDZ file extraced
20:29:18 : Files were extracted.
20:29:18 : LGMobileDL Load.
20:29:19 : Port = 0
20:29:19 : Connecting to phone
20:29:42 : PHONE WAS NOT FOUND!
20:29:44 : ===FINISHED===
Hi not_so_optimustic, did you do this?
**Navigate to Update/Tools and there select upgrade recovery.
Click to expand...
Click to collapse
Just in case:
In the own tool you have an option for install the drivers, you could try it.
Cheers . Good luck.
Sent from my LG P76020L-EUR-XX unlocked and rooted
BajoPrimate said:
Hi not_so_optimustic, did you do this?
Just in case:
In the own tool you have an option for install the drivers, you could try it.
Cheers . Good luck.
Sent from my LG P76020L-EUR-XX unlocked and rooted
Click to expand...
Click to collapse
Sorry for the delay. I have found some more time to try to fix it this weekend.
I am not sure what this part refers to:
**Navigate to Update/Tools and there select emergency recovery software.
Click to expand...
Click to collapse
There is no such menu visible in B2CAppSetup.exe that I can see.
Other oddities:
I was wrong about my phone model. it is actually an LG L9 MS769, not a P769. I don't know if that matters.
The B2CAppSetup.exe interface looks VERY different on my friends computer as opposed to mine. (see the attached screenshot) I am in the process of going through the motions on her computer to see if I get different results. However after opening the app and selecting my phone model and letting it install the drivers, I unplug and plug the USB cable again (staying in S/W mode), and nothing interesting happens beyond the circling "connecting" icon.
Let me know what you think. I'll keep trying.
I feel like I'm getting close! After installing the drivers, both the "Start Upgrade" and "Install USB Driver" buttons are greyed out. A message assures me that "Your device has the latest software available from the LG Mobile Support Tool", although this is clearly not true.
After clicking on the dropdown menu in the top right and selecting "Upgrade Recovery" it pops open the window pictured in the screenshot and attempts to download the software. This window stops progress at the download stage where the timer is frozen at 15 seconds.
Reinstall recovery image through fastboot
I managed to mess my L9 up several times before getting the bootloader unlocked, and one of the ways I got out of it was getting into fastboot using this method: http://forum.xda-developers.com/showthread.php?t=2119090 and then using fastboot commands to re-flash recovery, as described here: http://wiki.cyanogenmod.org/w/Template:Recovery_install_fastboot (step 6). You can find recovery img files in the second post on this thread: http://forum.xda-developers.com/showthread.php?t=2623222
If you can get into recovery again then you can flash a new rom, if I've understood your problem correctly. Good luck!
Try This one work if you install JB before [Need s/w update mode only]
not_so_optimustic said:
Hello, I shall do my best to shortly and concisely lay out my difficulties. (It was a bad decision to try to install a custom ROM on the Monday before finals)
I was looking to put a custom ROM on my phone, and was following this guide. I put CWM on my phone via this method. I had the ROM I wanted on my SD card. I boot into CWM, wipe the davlek cache like a good little boy, wipe the system (yikes), and select the .zip I want. Nope, status 7 error, abort! Heart racing slightly, I quickly Google and find a nice solution. Problem! When I reboot back into CWM... there is no CWM, and I'm stuck with the useless stock recovery mode that literally does nothing but show a picture of a dead android on its side.
I'm having issues with the offline installer. I've tried both the automated method and doing it myself but really nothing seems to be getting around the fact that my computer doesn't want to talk to my windows 8 computer, or my friend's windows 7 computer.
Here's some log output:
Code:
16:09:25 : [C:\LGMobileUpgrade] Try to delete folder
16:09:25 : RemoveDirectory1 Error(2):C:\LGMobileUpgrade
16:09:25 : Start Date : 2014-03-10 16:09:25
16:09:25 : ---------- QM Testmode ---------
16:09:25 : ***** Check Tool Version *****
16:09:25 : Tool version : 1.5.4.8
16:09:25 : UpgradeDLL version : 1.2.6.7
16:09:25 : Current Dir : C:\ProgramData\LGMOBILEAX\B2C_Client
16:09:26 : LGE USB Driver Version :
16:09:26 : Android PDLV Version :
16:09:26 : Android NDLV Version :
16:09:26 : ******************************************
16:09:26 : [C:\ProgramData\LGMOBILEAX\Phone] Try to delete folder
16:09:26 : RemoveDirectory1 Error(2):C:\ProgramData\LGMOBILEAX\Phone
16:09:26 : SetEmerModeAT()
16:09:26 : _IsConnectedPhone Call
16:09:35 : _IsConnectedPhone(0)
16:09:35 : 0 - NotConnected.
16:09:35 : 1 - Normal connect success
16:09:35 : 2 - Emergency connect success
16:09:35 : *****CheckOS Start********
16:09:35 : Microsoft_Windows7_Home Edition_
16:09:35 : *****CheckPCSyncPrograms Start*****
16:09:36 : PCSyncPrograms Not Found - OK and ready to upgrade
16:09:36 : Checking the connection with the cell phone...
16:09:36 : dwWaitResetTime(40000 ms)
16:09:37 : _IsConnectedPhone Call
16:09:44 : _IsConnectedPhone(0)
16:09:44 : 0 - NotConnected.
16:09:44 : 1 - Normal connect success
16:09:44 : 2 - Emergency connect success
16:09:45 : _IsConnectedPhone Call
16:09:52 : _IsConnectedPhone(0)
16:09:52 : 0 - NotConnected.
16:09:52 : 1 - Normal connect success
16:09:52 : 2 - Emergency connect success
16:09:53 : _IsConnectedPhone Call
16:10:01 : _IsConnectedPhone(0)
16:10:01 : 0 - NotConnected.
16:10:01 : 1 - Normal connect success
16:10:01 : 2 - Emergency connect success
16:10:01 : [009,400,102,102,102]The USB cable and your cellphone are not connected.\nPlease connect your phone and wait for connecting \nthe USB port for a while and press the [009,700,147,062,092]'Restart'[009,400,102,102,102] button.
16:10:11 : _IsConnectedPhone Call
16:10:11 : _IsConnectedPhone(0)
16:10:11 : 0 - NotConnected.
16:10:11 : 1 - Normal connect success
16:10:11 : 2 - Emergency connect success
16:10:11 : [009,400,102,102,102]The USB cable and your cellphone are not connected.\nPlease connect your phone and wait for connecting \nthe USB port for a while and press the [009,700,147,062,092]'Restart'[009,400,102,102,102] button.
16:10:17 : _IsConnectedPhone Call
16:10:24 : _IsConnectedPhone(0)
16:10:24 : 0 - NotConnected.
16:10:24 : 1 - Normal connect success
16:10:24 : 2 - Emergency connect success
16:10:24 : [009,400,102,102,102]The USB cable and your cellphone are not connected.\nPlease connect your phone and wait for connecting \nthe USB port for a while and press the [009,700,147,062,092]'Restart'[009,400,102,102,102] button.
16:11:02 : _IsConnectedPhone Call
16:11:02 : _IsConnectedPhone(0)
16:11:02 : 0 - NotConnected.
16:11:02 : 1 - Normal connect success
16:11:02 : 2 - Emergency connect success
16:11:02 : [009,400,102,102,102]The USB cable and your cellphone are not connected.\nPlease connect your phone and wait for connecting \nthe USB port for a while and press the [009,700,147,062,092]'Restart'[009,400,102,102,102] button.
16:11:04 : Check Cancel button active..
16:11:04 : Check Cancel button active..
16:11:04 : !pUpgrade->StartProcessing ... PostMsg STEP_TYPE_ENV_ERROR
16:11:04 : Page_Error ºÎºÐÀÔ´Ï´Ù
16:11:04 : [011,700,147,062,092]LG Mobile Phone Software Update was canceled\n\n[009,400,102,102,102]To quit LG Mobile Phone Software Update, please press the [009,700,147,062,092]Exit[009,400,102,102,102] button below.
16:11:04 : OnStepMsg STEP_TYPE_ENV_ERROR delete m_pLGCyonUpdate
And screenshots attached.
Listed in Device Manager:
ADB Interface > Android Platform Sooner Single ADB Interface
Modems > LGE Android Platform USB Modem
> LGE Mobile USB Modem
> LGE Mobile USB Modem #2
Other Devices > Unknown device (I installed the fastboot drivers to this, had to get around the driver signature stuff)
Ports (COM & LPT) > LGE Android Platform USB Serial Port (COM7)
> LGE Mobile USB Serial Port (COM4)
> LGE Mobile USB Serial Port (COM6)
Universal Serial Bus Controllers > LGE Mobile Composite USB Device
> LGE Mobile Composite USB Device
Please help if you can. Thank you.
Click to expand...
Click to collapse
Try This one work if you install JB before [Need s/w update mode only]
http://forum.xda-developers.com/show....php?t=2686746
davidxd said:
I managed to mess my L9 up several times before getting the bootloader unlocked, and one of the ways I got out of it was getting into fastboot using this method: http://forum.xda-developers.com/showthread.php?t=2119090 and then using fastboot commands to re-flash recovery, as described here: http://wiki.cyanogenmod.org/w/Template:Recovery_install_fastboot (step 6). You can find recovery img files in the second post on this thread: http://forum.xda-developers.com/showthread.php?t=2623222
If you can get into recovery again then you can flash a new rom, if I've understood your problem correctly. Good luck!
Click to expand...
Click to collapse
I flashed the recovery (successfully?). My next confusion is how to boot into it. My device now shows the LG logo at boot and "Security Error" underneath.
Code:
C:\omap4boot-for_optimus-v1.21>start_fastboot.bat
--------------------------------------------
OMAP4boot for P920/P720/SU540/SU760/SU870
--------------------------------------------
by wkpark at gmail dot com
[1] cx2 - Optimus 3D Cube (SU870/P720)
[2] p920 - Optimus 3D (P920)
[3] p940 - Prada 3.0 (P940)
[4] su540 - Prada 3.0 (SU540/KU5400)
[5] su760 - Optimus 3D (SU760)
[x] exit
-------------------------------------------
Select device and <ENTER> 3
p940 selected
waiting for OMAP44xx device...
Device descriptor:
bLength = 18
bDescriptorType = 1
bcdUSB = 528
bDeviceClass = 255
bDeviceSubClass = 255
bDeviceProtocol = 255
bMaxPacketSize0 = 64
idVendor = 451
idProduct = D00F
bcdDevice = 0
iManufacturer = 33
iProduct = 37
iSerialNumber = 0
bNumConfigurations = 1
reading ASIC ID
usb_write 4
usb_read 81
[*] read 0 bytes
NumOfSubblocks: 0x5
Subblock ID: 0x1
Subblock Size: 0x5
CH enabled: 0x7
ROM revision: 0x4
Checksum Subblock: 0x15
CHIP: 4430
IDEN: 5fd90f8f47e3dafb559b8cc604f1b59164668513
MPKH: 5f4092eccddf90fa43f546adf89508b31b9c74795e9516194c0ea6412fdcb7f6
CRC0: 9c669ad9
CRC1: 682adccf
sending 2ndstage to target... f0030002
usb_write 4
usb_write 4
wait 5-seconds...
[*] msg size = 4
usb_write 21552
[*] data size = 21552
usb_close
Reopen usb...
Device descriptor:
bLength = 18
bDescriptorType = 1
bcdUSB = 528
bDeviceClass = 255
bDeviceSubClass = 255
bDeviceProtocol = 255
bMaxPacketSize0 = 64
idVendor = 451
idProduct = D00F
bcdDevice = 0
iManufacturer = 33
iProduct = 37
iSerialNumber = 0
bNumConfigurations = 1
waiting for 2ndstage response...
usb_read 4
usb read = aabbccdd
accepted 2ndstage response
sending image to target...
size = 246272
usb_write 4
usb_write 246272
** Done **
------------------------------
Please remove USB cable
and wait until LG Logo on
then reconnent USB cable again
------------------------------
fastboot devices (y/N) ? and press <ENTER> n
ls: resigned/p940-MLO*.bin: No such file or directory
Do you want to replace u-boot (y/N) ?n
ls: cwm/p940-*.img: No such file or directory
Press any key to continue . . .
0163953A1401F010 fastboot
Microsoft Windows [Version 6.1.7601]
Copyright (c) 2009 Microsoft Corporation. All rights reserved.
C:\omap4boot-for_optimus-v1.21>fastboot flash recovery recovery-clockwork-6.0.3.
1-p760.img
sending 'recovery' (5894 KB)...
OKAY [ 3.020s]
writing 'recovery'...
OKAY [ 1.538s]
finished. total time: 4.559s
C:\omap4boot-for_optimus-v1.21>fastboot reboot
rebooting...
finished. total time: 0.003s
C:\omap4boot-for_optimus-v1.21>
Oh ****. My phone does not boot, period. It still goes into fastboot mode when connected to the computer. I tried following the steps a few more times, and during my last attempt, after
Code:
At the other prompts answer always "N", this could be important.
I pressed "y" and it replaced "u-boot." Currently hitting myself over the head. How do I reflash the stock u-boot?
Hi not_so_optimustic, you could try this http://forum.xda-developers.com/showthread.php?p=48834061.
Cheers. Good luck
Sent from my LG P76020L-EUR-XX unlocked and rooted
u-boot
This post might help you there:
http://forum.xda-developers.com/showpost.php?p=40121966&postcount=7
davidxd said:
This post might help you there:
http://forum.xda-developers.com/showpost.php?p=40121966&postcount=7
Click to expand...
Click to collapse
I didn't manage to get that fix to work as I got errors of "The program can't start because AbdWinApi.dll is missing from your computer. Try reinstalling the program to fix this problem."
HOWEVER
BajoPrimate said:
Hi not_so_optimustic, you could try this http://forum.xda-developers.com/showthread.php?p=48834061.
Cheers. Good luck
Sent from my LG P76020L-EUR-XX unlocked and rooted
Click to expand...
Click to collapse
This worked pretty perfectly to fix the u-boot problem. After flashing the three attached images for u-boot, boot, and recovery, the boot process was back to "normal." So I then used "fastboot flash recovery [my cwm file]" and it flashed successfully again, and I'm back to the LG logo with the security error, and not really sure how to get to CWM.
The guide you linked to recommends the offline fix, which is the method I've been having issues with. My goal at this point is to get CWM to start properly so I can flash my ROM from the SD card. However the method to fix the security error involves installing a different recovery (not CWM). So that's where I stand at this point.
I'll do some more research and be back here to report whatever my next screwup happens to be.
EDIT: So I think my security error is due to my bootloader not being unlocked. I will attempt to follow this guide and we'll see how it goes. http://forum.xda-developers.com/showthread.php?t=2221102
EDIT2: The first link says to go here for p769. Unfortunately that method requires my device to already be working -_- the search goes on.
not_so_optimustic said:
I didn't manage to get that fix to work as I got errors of "The program can't start because AbdWinApi.dll is missing from your computer. Try reinstalling the program to fix this problem."
HOWEVER
This worked pretty perfectly to fix the u-boot problem. After flashing the three attached images for u-boot, boot, and recovery, the boot process was back to "normal." So I then used "fastboot flash recovery [my cwm file]" and it flashed successfully again, and I'm back to the LG logo with the security error, and not really sure how to get to CWM.
The guide you linked to recommends the offline fix, which is the method I've been having issues with. My goal at this point is to get CWM to start properly so I can flash my ROM from the SD card. However the method to fix the security error involves installing a different recovery (not CWM). So that's where I stand at this point.
I'll do some more research and be back here to report whatever my next screwup happens to be.
EDIT: So I think my security error is due to my bootloader not being unlocked. I will attempt to follow this guide and we'll see how it goes. http://forum.xda-developers.com/showthread.php?t=2221102
EDIT2: The first link says to go here for p769. Unfortunately that method requires my device to already be working -_- the search goes on.
Click to expand...
Click to collapse
What problem are you having with the offline flash? If the problem was that it stops at 15%, that's because you had a jellybean u-boot. The offline should work now.
Sent from my LG-P769 using XDA Premium 4 mobile app
I
kuma82 said:
What problem are you having with the offline flash? If the problem was that it stops at 15%, that's because you had a jellybean u-boot. The offline should work now.
Sent from my LG-P769 using XDA Premium 4 mobile app
Click to expand...
Click to collapse
Oh! Well. Is it safe to flash CM11 when I have an Ice Cream Sandwich u-boot?
not_so_optimustic said:
I
Oh! Well. Is it safe to flash CM11 when I have an Ice Cream Sandwich u-boot?
Click to expand...
Click to collapse
No
You will get a security error even if your bootloader is unlocked.
Sent from my LG-P769 using XDA Premium 4 mobile app
I installed the stock ROM via the offline fix successfully! It immediately went into a nonstop boot loop of the LG logo, so I turned it off and did a hard reset (volume up + home + power, let go of power after it starts up), which then allowed me to boot into the system.
THANK YOU so much! I am now the happiest person on the planet. Can I buy any of you a beer?
not_so_optimustic said:
I installed the stock ROM via the offline fix successfully! It immediately went into a nonstop boot loop of the LG logo, so I turned it off and did a hard reset (volume up + home + power, let go of power after it starts up), which then allowed me to boot into the system.
THANK YOU so much! I am now the happiest person on the planet. Can I buy any of you a beer?
Click to expand...
Click to collapse
Glad you got it fixed
Sent from my LG-P769 using XDA Premium 4 mobile app
Hi not_so_optimustic, happy to help!
Cheers. Good luck.
Sent from my LG P76020L-EUR-XX unlocked and rooted