Related
*Note i have not experienced whether the product lives up to its name or not. I only JUST placed it on my device. This is simply my first impression.
**I included pictures of my device compared to the back parts of the adhesive so you can fully grasp the wonderful "custom to fit" experience.
I just now got as close to perfection as i think i am going to get with placing my "custom to fit" screen protector onto my device. At very first glance i saw that their were going to be some slight imperfections. The random circle on the top right of the adhesive was a dead giveaway. The cut out they have for the top speaker and the bottom row of buttons is hardly CLOSE to the size it should be. It is much too big. I am not sure if it is clear enough in the pictures but their is excess adhesive on the sides. I figured they may be meant to fold down to protect a minuscule amount of siding. At first i could not get it to stick on the sides. But after giving it a few minutes to settle and let the application spray* dry, it seems to be holding. However, the border has really ugly bubbles from the very tony inlay of the front of the phone. The instructions say that MICRObubbles will disappear in their own after a couple days... i hardly find these MICRObubbles though. We will see. I think it is almost supposed to have a "melting" effect on the device. Like heated plastic sort of taking the proper shape over the device.
Now we move onto the back. You will see that i have been given 3 holes instead of 2. (2 being the camera lens and the button underneath). I have no idea what the third was meant for.... I can also forget about taking the backing off of my device as it is now sealed shut with the plastic invisible shield. This doesn't bother me that much since i rarely ever have to take the back out but i know their will be a day where i will need to.
All-in-all the product LOOKS promising still. The bottom line here that i would like to make is that i have NO idea what TouchPro2 they are basing this off of. but it is far from mine. Too far. I need to check but i am also fairly certain they ask for your provider too (in case the device is different than others)
I am also still wondering about the excess sides. it is very random in the back but they make no mention of needing to trim the shield.
*They give you a spray that you use on your fingertips and the adhesive so that a. you dont give it fingerprint smudges and b. it doesnt fully stick right away so that you can "slide" it into place. I found that "sliding" it around was impossible because it still stuck but it did not stick enough to the point i was unable to retry.
I really hope this means something to somebody. Had i read something like this before hand, i may have thought longer on buying the product. I will be sure to write more in the next few days. By the feel of the material on my phone, it seems like it could work really well.
I would also love to know other people's experience with this product and even maybe correct me if anything i complained about was just due to stupidity.
It very much looks like you bought Invisible Shield for the wrong Touch Pro 2 model.
It looks like you have the one for the unlocked/unbranded model:
http://www.zagg.com/invisibleshield/htc-touch-pro-2-cases-screen-protectors-covers-skins-shields.php
When in fact you want the T-Mobile model.
http://www.zagg.com/invisibleshield/htc-touch-pro-2-t-mobile-cases-screen-protectors-covers-skins-shields.php
It looks like the shape of your T-Mob branded TP2 is actually quite different from the unbranded version. The shape of the shield is therefore quite different between the models, based on the pictures on the Zagg website. Also, the layout of the battery cover is totally different, which is why the cutouts on the shield don't match your battery cover. This also accounts for the 3rd small hole on this piece. In addition to the camera lens and speakerphone button, the unbranded TP2 has small holes for the speaker just below the speakerphone button, and that is what the 3rd hole in the shield is for. I'm guessing on the T-Mob version, the speaker hole is located as part of the larger cutout/hole.
Not to be mean but it's really obvious that it wasn't made for a T-Mobile Touch Pro2 and you should have known that it wasn't the right one.
Just going to the Touch Pro2 forums you can see that there's different versions of the device and ours is usually always referred as the "T-Mobile Touch Pro2" when being specific.
The cover does seem worth buying though.
Yeah i just inquired about it. I did buy the T-Mobile one and they just sent the wrong one.
redpoint73 said:
In addition to the camera lens and speakerphone button, the unbranded TP2 has small holes for the speaker just below the speakerphone button, and that is what the 3rd hole in the shield is for. I'm guessing on the T-Mob version, the speaker hole is located as part of the larger cutout/hole.
Click to expand...
Click to collapse
Oddly, the Tilt2 had little holes in the back case in the same spot, despite the fact that it is just the battery sitting behind the holes. I always figured it was just a way to give water quick access to the battery compartment to turn that little strip pink incase we ever dropped it somewhere damp...
Saw this case when searching on Ebay
MOD EDIT: Ebay Links
Guess I can't link it, but search ebay for
"leather case cover for 10.2"inch epad" if you want it, seller is chinese-smile and it's a little higher priced now, but still only $9.96.
Dimensions for the
EPad iRobot are 270mmx180mmx15mm
GTablet are 267x173x9-13.9(mm)
This sounds like it would be a pretty good fit, although the soft keys would be covered, some surgery would be needed, but for $9.49! Only thing it is PU, not real leather, even chinese cows aren't that cheap apparently. ;P
I'm going to order this, I'll update when it arrives.
UPDATE: See Roebeet and i2steve comments on the case as they already have one, not perfect, but usable with a little adjustments.
bought one too, lets see what happens
I'm trying it too. We'll see..
Call me a Lemming too... Should work out pretty good.
Trying here too..
This looks exactly like the case thst roebeet and myself have. I did a small review on it in the accessories thread.
Sent from my SGH-T959 using Tapatalk
Yeah, that's the case I have (I thought I was getting one with clips, but got this one instead).
I am using mine right now, but had to do some surgery on it. Quick notes, from my own experience:
- the volume keys are covered, so you need to cut there.
- the camera and light sensors are covered.
- All the keys are covered, except a little bit of the back button.
- our device is a tad too think, so it will bulge in places.
- the screen is covered a bit on the top side, and you'll need to cut away a whole section of the top to fix that.
Suggestion: Lots of electrical tape to cover up the surgery - it doesn't look all that great, but it gets the job done until something better comes along. Btw, this is a situation where having cheap faux leather is a good thing, as it's fairly easy to cut - I used a razor blade and a hole puncher.
A final suggestion is to get some reusable sticky tape (1 lb strength max) to reduce the bulges and hold it together and a little velcro on the side clip so you can have it stick to the back when it's opened. If you don't use velcro, it basically sticks out when you flip it open, which is a bit annoying.
Good summary above ^^^
I just got mine and I like it. Been carrying mine in the bag from the original box, so this is nice.
Like he said above, the buttons are covered, but if you have the VEGAn Rom, with the home, back and menu buttons in the window shade, you won't have to cut. Although it's a little tricky hitting them, cause it's tight up there.
I just quickly slide it out an inch or two if I need to adjust the volume.
I love how the case props it up so it's at a 60° angle.
Until a better one comes out, this will more than suffice.
Hi all,
Ok, so i've had a small disaster. As you probably guessed already i've dropped my phone. I thought the story was quite amusing (or just plain unfortunate!) so i'll you tell that before I ask for some advice!!
I got myself a white Galaxy S2 on upgrade through Vodafone. Gorgeous piece of kit so I ordered myself a nice case and screen protector to keep it nice and tidy.
Unfortunately the case got 'lost in the post' and as such the phone was unprotected. So, with some foresight I ordered a plain white cheap one off eBay (£2 inc. postage) just to see me through the 3-5 days I needed before the case I wanted was resent.
However what was sent what not white at all - it was the most hideous case with a rather disgusting floral effect all over it. I was going out for a night in town and had no choice, I had to take it with me.
Unfortunately later that eve I was stood at the bar, and my phone went off. So to save any embarrassment I slid the phone out of it's hideous case, and proceeded to read the message. Then it happened. The slippery son of a ***** jumped out of my hand, bounced off my foot and hit the deck.
It only has a couple of dings in the chrome bezel (the chrome effect rubbed off in two places to reveal black (the plating is obviously really thin)) - everything else was ok. Phew. But i'm still gutted and annoyed with myself
So, lesson learnt. I should have left the disgusting garish floral case on and it would have saved my phone. It was only 'de-sheathed' for a second and I managed to drop it, classic.
As a temporary solution, I coloured in the affected areas of the bezel with a silver permanent marker, and used some clear nail varnish over the top to stop the pen coming off. It seems to work well actually, and it looks much better than the black marks.
So, to my question - how do I change the chrome bezel for a new one?
I have read many threads, and watched many videos, and it looks to me like a nightmare job (eg as well as taking off the back and all components, you have to prise off the screen which is glued on, disconnect digitiser, etc). Can anyone confirm this, or has anyone tried it?
I can't find any videos of changing the bezel - they all seem to only go as far as taking off the back.
I've found a couple of sellers which sell the housing in white for only £20-30, so if it's an easy-ish job i'd have a stab at it. However i'm thinking I might as well just forget it ever happened and not be so precious about keeping the phone in A1 condition - it's a phone after all and it's going to encounter some scrapes now and then, even with a case on. And I plan on keeping it for 18 months anyway.
Opinions, anyone?
Cheers!
Movisman said:
Hi all,
Ok, so i've had a small disaster. As you probably guessed already i've dropped my phone. I thought the story was quite amusing (or just plain unfortunate!) so i'll you tell that before I ask for some advice!!
I got myself a white Galaxy S2 on upgrade through Vodafone. Gorgeous piece of kit so I ordered myself a nice case and screen protector to keep it nice and tidy.
Unfortunately the case got 'lost in the post' and as such the phone was unprotected. So, with some foresight I ordered a plain white cheap one off eBay (£2 inc. postage) just to see me through the 3-5 days I needed before the case I wanted was resent.
However what was sent what not white at all - it was the most hideous case with a rather disgusting floral effect all over it. I was going out for a night in town and had no choice, I had to take it with me.
Unfortunately later that eve I was stood at the bar, and my phone went off. So to save any embarrassment I slid the phone out of it's hideous case, and proceeded to read the message. Then it happened. The slippery son of a ***** jumped out of my hand, bounced off my foot and hit the deck.
It only has a couple of dings in the chrome bezel (the chrome effect rubbed off in two places to reveal black (the plating is obviously really thin)) - everything else was ok. Phew. But i'm still gutted and annoyed with myself
So, lesson learnt. I should have left the disgusting garish floral case on and it would have saved my phone. It was only 'de-sheathed' for a second and I managed to drop it, classic.
As a temporary solution, I coloured in the affected areas of the bezel with a silver permanent marker, and used some clear nail varnish over the top to stop the pen coming off. It seems to work well actually, and it looks much better than the black marks.
So, to my question - how do I change the chrome bezel for a new one?
I have read many threads, and watched many videos, and it looks to me like a nightmare job (eg as well as taking off the back and all components, you have to prise off the screen which is glued on, disconnect digitiser, etc). Can anyone confirm this, or has anyone tried it?
I can't find any videos of changing the bezel - they all seem to only go as far as taking off the back.
I've found a couple of sellers which sell the housing in white for only £20-30, so if it's an easy-ish job i'd have a stab at it. However i'm thinking I might as well just forget it ever happened and not be so precious about keeping the phone in A1 condition - it's a phone after all and it's going to encounter some scrapes now and then, even with a case on. And I plan on keeping it for 18 months anyway.
Opinions, anyone?
Cheers!
Click to expand...
Click to collapse
Sorry to hear...similar happened to my HTC Desire...however this should help...if you buy the kit off Ebay...
http://forum.xda-developers.com/showthread.php?t=1253969
0semaj0 said:
Sorry to hear...similar happened to my HTC Desire...however this should help...if you buy the kit off Ebay...
http://forum.xda-developers.com/showthread.php?t=1253969
Click to expand...
Click to collapse
Hi,
Thanks for the information - I had a look at this tutorial yesterday, and although it's very good, it looks like this person has replaced the entire led panel/digitiser/housing in one go, rather than just the housing?
My screen is just fine, so I only need to replace the housing part.
The hardest bit looks like separating the screen from the housing from what i've read, and this is what I can't find a tutorial for, only some images on youtube suggesting to use a hairdryer to help with the proceedings!!
Thanks
Movisman said:
Hi,
Thanks for the information - I had a look at this tutorial yesterday, and although it's very good, it looks like this person has replaced the entire led panel/digitiser/housing in one go, rather than just the housing?
My screen is just fine, so I only need to replace the housing part.
The hardest bit looks like separating the screen from the housing from what i've read, and this is what I can't find a tutorial for, only some images on youtube suggesting to use a hairdryer to help with the proceedings!!
Thanks
Click to expand...
Click to collapse
Yea, the link is for the whole unit, but would give you some pointers. I am not as familar with the Samsung build, but with the HTC I know that between the LCD housing and the LCD/digitiser itself is applied through adhesive (most phones are) that is put into a temperature oven for 10 minutes to soften the adhesive. This is based on the HTC Official Service videos. I am not sure if the same will apply to Samsung phones.
But then again, as it is an expensive phone, it may be ideal for you to also get a quote from your local SSC or mobile phone repair agent to consider.
0semaj0 said:
Yea, the link is for the whole unit, but would give you some pointers. I am not as familar with the Samsung build, but with the HTC I know that between the LCD housing and the LCD/digitiser itself is applied through adhesive (most phones are) that is put into a temperature oven for 10 minutes to soften the adhesive. This is based on the HTC Official Service videos. I am not sure if the same will apply to Samsung phones.
But then again, as it is an expensive phone, it may be ideal for you to also get a quote from your local SSC or mobile phone repair agent to consider.
Click to expand...
Click to collapse
Yep, good point. I'd be interested to hear actually what the cost would be to replace the front bezel only. It's only £30 on eBay for the front and rear housing, but i'd be willing to pay more on top for an authorised repairer to carry out the job.
That tutorial is definitely one of the more detailed ones I have seen so far though. Doesn't look like many people have tackled changing the bezel only...
Thanks
Movisman said:
Yep, good point. I'd be interested to hear actually what the cost would be to replace the front bezel only. It's only £30 on eBay for the front and rear housing, but i'd be willing to pay more on top for an authorised repairer to carry out the job.
That tutorial is definitely one of the more detailed ones I have seen so far though. Doesn't look like many people have tackled changing the bezel only...
Thanks
Click to expand...
Click to collapse
Hey Movis,
What did you end up doing for your dropped phone?
I too have dropped my phone on its corner and the chrome along with the plastic is now dented.
Another one with the same problem here. I managed to create a bump on the chrome bezel.
Can I bump this post as I've also just noticed a ding in the corner of the chrome bezel was wondering if anyone had found a solution to this yet.? short of replacing the LCD/digitiser which like OPs phone are working fine. It's just cosmetic damage.
I once was in a bad mood and snapped a screen and backing/housing in half.I can't remember exactly,but I'm thinking the chrome bit may be part of the thin metal casing/housing that is glue taped onto the screen.
You separate the screen from the housing by using a hot air gun sparingly.
If you look back at a motherboard thread I was involved in,a person on here called Roger put up a great video tutorial link that may answer all your questions...
Sent from my GT-I9100
Ah cheers for the reply. Had a look at the mobo post you were involved in followed it to the link and coincidentally that's the exact video I watched last night. Very good video good detail and instructions. But its the black one he is stripping down so he makes no reference to the bezel which afaik is only used on the white ones.
Sent from my GT-I9100 using xda premium
I've not seen the chrome bit listed separately,so I guess its part of the metal top housing that the LCD is glued to.I've got a white one and its got a ding on it too.
You could email Samsung to see if you can get the part,but I think its not worth risking cracking the screen and you probably couldn't resuse / would get that stupid gluey tape stuff.
Sent from my GT-I9100
Appreciate it's been a while, but this seems to be the only post that matches what happened to me, so figured I'd update with my experience.
As above, dropped and dented the bezel, screen was perfectly intact, but the dent was so severe, it actually lifted a corner of my screen up. I have intentions to sell on so I wanted to fix this and pass on.
I followed this disassembly , apart from the bit about not worrying about damaging the screen as you prise it away. The housing I ordered off ebay came with a little kit, so I warmed the screen with hairdryer for a couple of minutes, then slowly prised it away, from top to bottom, inserting the tool right down the middle as the video mentions there is a large adhesive right down the middle.
Following the vid all the way to the removal of all components, this is where I ditched my current bezel/housing and reassembled into the newly ordered one. Judging by the assembly, there is no way that a bezel could be replaced without replacing the housing, it's one whole unit, and I very much doubt the build would be that drastically different for the white SGS2.
Some things to note:
Be very careful removing the vibrate motor, the connector and natural pivot point is the weakest part (new module ordered from ebay
If you are transplanting the screen like me, have some adhesive pads in your kit as most tutorials are for new screens, and as can be seen on the vid, these come with pads intact, ready to apply
Try do it in daylight
Hope that helps anyone in a similar situation.
vyks10 said:
Appreciate it's been a while, but this seems to be the only post that matches what happened to me, so figured I'd update with my experience.
As above, dropped and dented the bezel, screen was perfectly intact, but the dent was so severe, it actually lifted a corner of my screen up. I have intentions to sell on so I wanted to fix this and pass on.
I followed this disassembly , apart from the bit about not worrying about damaging the screen as you prise it away. The housing I ordered off ebay came with a little kit, so I warmed the screen with hairdryer for a couple of minutes, then slowly prised it away, from top to bottom, inserting the tool right down the middle as the video mentions there is a large adhesive right down the middle.
Following the vid all the way to the removal of all components, this is where I ditched my current bezel/housing and reassembled into the newly ordered one. Judging by the assembly, there is no way that a bezel could be replaced without replacing the housing, it's one whole unit, and I very much doubt the build would be that drastically different for the white SGS2.
Some things to note:
Be very careful removing the vibrate motor, the connector and natural pivot point is the weakest part (new module ordered from ebay
If you are transplanting the screen like me, have some adhesive pads in your kit as most tutorials are for new screens, and as can be seen on the vid, these come with pads intact, ready to apply
Try do it in daylight
Hope that helps anyone in a similar situation.
Click to expand...
Click to collapse
Hi, will the heat actually damage the screen? I saw some posts mentioning about putting it into the oven and such. It sounded very intense but if it works without damaging the screen, i might give it a try. Facing the same situation as yours. Scratches and dents all over my front chrome bezel.
Dear all,
I am here to just warn you of who ever owns a roxfit case, for those who have not stick it on to their phone you might want to reconsider before doing so. And for those who have it on already you might want to reconsider as well.
I bought this case like a month ago and used it for a month. Yes it is a good case "full protection" but when i tried to take it off today i realized the following:
1- it is a PAIN in the ____ to take it off, I am not even kidding. You might think why would you want to take it off? cause one day you want to clean up the dust, take out the sim card, or maybe switch case. I nearly had to break the top left corner, that little thin strand infront of the power button, and find something to stick into the top right.
Yes, i know it might not be the right way to take it off, but I have done some research and it seems like no one knows what is the "proper way" to take it off.
ANYWAY to get to the worst part
2- you know the inside of the case it has the black rectangle thingy with white words on it saying "roxfit?" Well, when i took off the case, i realized a bunch of little tiny black/grey dots on the back of my phone. No, I cannot rub it off, and i also tried erasing it off (which is not a good idea, cause it does rub off the anti-coating and causes it to look shiny which was described in another thread)
I know its just the back cover, but still...
Not trying to complain or anything, just keep your eyes open when choosing your case
LitoNi said:
Dear all,
I am here to just warn you of who ever owns a roxfit case, for those who have not stick it on to their phone you might want to reconsider before doing so. And for those who have it on already you might want to reconsider as well.
I bought this case like a month ago and used it for a month. Yes it is a good case "full protection" but when i tried to take it off today i realized the following:
1- it is a PAIN in the ____ to take it off, I am not even kidding. You might think why would you want to take it off? cause one day you want to clean up the dust, take out the sim card, or maybe switch case. I nearly had to break the top left corner, that little thin strand infront of the power button, and find something to stick into the top right.
Yes, i know it might not be the right way to take it off, but I have done some research and it seems like no one knows what is the "proper way" to take it off.
ANYWAY to get to the worst part
2- you know the inside of the case it has the black rectangle thingy with white words on it saying "roxfit?" Well, when i took off the case, i realized a bunch of little tiny black/grey dots on the back of my phone. No, I cannot rub it off, and i also tried erasing it off (which is not a good idea, cause it does rub off the anti-coating and causes it to look shiny which was described in another thread)
I know its just the back cover, but still...
Not trying to complain or anything, just keep your eyes open when choosing your case
Click to expand...
Click to collapse
I've have 2 of their products for my S, I have the hard shell, which I broke trying to take it off, those little this bits near the switches are a pain and a weak spot. This case had a thin felt patch inside to stop it rubbing the back of my S.
I also have the leather flip over case , i've had to stop using this because unlike the hard shell there is no felt patch inside to stop it rubbing , now I have marks on the back of my phone.
For the money I paid for these items, you'd think a bit more thought would go into the design...
I know, matte coating is not a cool thing, it just feels nice.
i dont know about your XPS but on mine the front bottom part where it says "xperia" that part is also glossy shiny, obviously that part's anti coating is rubbing off just by putting in my pockets.
this is what i am planning to do instead of making the same mistakes again.
the best thing to do is to get the zagg full body kit and protect the [ top, bottom, and the "xperia part" on the front ] and then get a case that only covers the sides and the back.
I had a roxfit and never had such problems.
Sent from my LT26i using Tapatalk 2
Thanks for the warning. In the case thread there was someone saying something about the shell feeling loose. (maybe it was you, dont remember).
I guess thats what you get with a hard shell that covers the phone's back and sides completely unless it was made of two parts or from soft material like TPU. I thought of buying this on long time ago because none of the TPU cases had a good fitt (and the buttons still usable).
I never did buy this one, but thougt about it since it's for me the best next to my TPU preference. I'm using a (little reshaped with hot water) 'Nillkin' TPU case at the moment. I also have a 'Gimmick Five' hard case, but i don't like the edges (like almost all hard cases) , its not smooth when putting it in and getting it out of my pocket for a phone with this size. I also do't think those cases offer much protection.
If you're planning on buying a ZAGG invisibleShield read this too: http://forum.xda-developers.com/showpost.php?p=27896421&postcount=6
and remember this skin is only for scratches not fall damage duh (cases/covers/shells might help a little with low height falls)
---------- Post added at 03:19 PM ---------- Previous post was at 02:57 PM ----------
superlimau said:
I had a roxfit and never had such problems.
Click to expand...
Click to collapse
Can you give us some more info? how is the fit? is it easy to take out? do you have any little scratches of the coating on the edges?
@LitoNi The case is a little flexible, maybe it has also to do with how someone tries to pull of the case?
I took my case many times off. Yeah it's not easy, that's for sure but I can't confirm your other complaints.
My phone slipped once out of my hand and landed on hard ground. I just have a few scratches on the top right corner and bottom left corner.
without the case the damage would have been probably much worse.
The case also was damaged in the bottom.
Currently I'm waiting for my nillkin flip leather case. Hope it will protect the front as well now.
Edit: that is now a little embarrassing. I actually have a krusell case, but the should be the same
I have the roxfit hard shell as well. It fits perfectly and doesn't feel loose at all. As for taking it off, well yeah it's a snug fit, so taking it off requires a bit of fiddling. But it is definitely not impossible to take it off without breaking it. Then again you shouldn't have to take it off daily, so for me it's not a problem.I usually just push the bottom corners of the case down, then you can stick your nail through the hole on the bottom and just push the phone out completely. Not that hard to do.
Also mine does not leave any traces on the phone. I'm pretty happy with this case.
Sent from my LT26i using xda app-developers app
i guess i was just the unlucky one with the stains.
anyway i changed the title so it wont be directly talking about roxfit, but cases in general
taking it out is slightly a pain in the ass... you need to flick it out from the powet button corner follow by volume side... one you flick it past both the 2 buttons, the rest is a breeze...
no there's no stain on the phone....
thanks
Thanks for the warning..
superlimau said:
taking it out is slightly a pain in the ass... you need to flick it out from the powet button corner follow by volume side... one you flick it past both the 2 buttons, the rest is a breeze...
no there's no stain on the phone....
Click to expand...
Click to collapse
i start with the left side and bottom, then top side and last the right side. works everytime
Let me add that there is also a slider shell case: Incipio EDGE Hard Shell Slider Case
But please talk about this on the Xperia S Case show thread and let this thread be only for the Roxfit and Krusell shells :fingers-crossed:
It has done exactly the same to my phone....It's a joke!!!!!
Okay guys. As you all know, you can't paint aluminum. Spending a bit of time on Oakley forum, it dawned on me that you can duracoat or cerakote a phone. I have a gold a 2017u that is begging for a refinish. I hate gold, but love this phone. Just curious whether anyone has attempted such or if I will be the first monkey launched into space. Just had my X metal XX refinished and would love the gold to be gone. If we had a hardware modding section, I'd post there. Lol.
What about the antenna bands? Fingerprint reader? What about the plastic speaker covers? Most people, including me, are going to tell you that it's just not worth it. This is especially true if it's just for a color change and not to cover scratches. I actually just bought a gold A7 because I think they look nicer in a case than the grey ones do. I'm normally one for subdued colors but in this case the color of the phone is just an accent color. If you do it, pick a color that isn't offered to make it interesting and post the pictures here.
kitcostantino said:
Okay guys. As you all know, you can't paint aluminum. Spending a bit of time on Oakley forum, it dawned on me that you can duracoat or cerakote a phone. I have a gold a 2017u that is begging for a refinish. I hate gold, but love this phone. Just curious whether anyone has attempted such or if I will be the first monkey launched into space. Just had my X metal XX refinished and would love the gold to be gone. If we had a hardware modding section, I'd post there. Lol.
Click to expand...
Click to collapse
Lol I can't count how many times I've been tempted to take a piece of sandpaper and at least get rid of the gold finish...
The good thing about the construction of this thing is that once you take it apart, only the FP reader and the camera lens remain there. I guess you can get the lens out with a little bit of pressure and take that gold ring off. The reader has a piece of what seems to be tape upon it, but you may as well leave it there. and having the two antenna lines of another color may even look nice
I really want to see the final product...
I'm torn between durabake and duracoat aerosol. I'm fairly confident that powered off, the 200 degrees f would not melt anything plastic on the phone. I wish I knew more about temperature tolerances. Also. I'm torn between primary red and nwu blue. The aerosol kit doesn't require baking, so likely that is a safer option.
Update: duracoat aerosol ordered.
kitcostantino said:
I'm torn between durabake and duracoat aerosol. I'm fairly confident that powered off, the 200 degrees f would not melt anything plastic on the phone. I wish I knew more about temperature tolerances. Also. I'm torn between primary red and nwu blue. The aerosol kit doesn't require baking, so likely that is a safer option.
Update: duracoat aerosol ordered.
Click to expand...
Click to collapse
Wait, you are dissembling the phone right? I vote blue but it's too late.
lol. yes. and i ordered the nwu blue.
honestly, i think it will be a great project. if it works, it will be the motivation to acquire a 64/128. (not too motivated on that presently bc of the hideous gold.) NWU blue should be worlds better than ghetto gold.
i plan to take the phone apart.
i plan to duracoat the speaker grills the same color. same thing on sim tray and the parts where the plastic antennae lines are. i honestly could pull off doing it w/o pulling it apart and taping/masking well considering it doesnt have to bake. but i feel like the pita of full disassembly may be worthwhile.
ive taken many many phones apart. so i am not squeamish there. i just am not certain that the fingerprint sensor and the sapphire glass on the camera are that hard to mask off. (eyes crappy slickwraps extras. lol)
edit: after watching this video:
, i *definitely* am disassembling. i am so stoked for a blue axon. i wish i could make a red decal to replace the logos.
kitcostantino said:
honestly, i think it will be a great project. if it works, it will be the motivation to acquire a 64/128. (not too motivated on that presently bc of the hideous gold.) NWU blue should be worlds better than ghetto gold.
i plan to take the phone apart.
i plan to duracoat the speaker grills the same color. same thing on sim tray and the parts where the plastic antennae lines are. i honestly could pull off doing it w/o pulling it apart and taping/masking well considering it doesnt have to bake. but i feel like the pita of full disassembly may be worthwhile.
ive taken many many phones apart. so i am not squeamish there. i just am not certain that the fingerprint sensor and the sapphire glass on the camera are that hard to mask off. (eyes crappy slickwraps extras. lol)
edit: after watching this video:
, i *definitely* am disassembling. i am so stoked for a blue axon. i wish i could make a red decal to replace the logos.
Click to expand...
Click to collapse
Well, I took apart my Moto G 2 and while these 2 phones are worlds apart in terms of build quality, all it took was a soft piece of wood and some force to get the camera lens to pop off. was riddled with scratches. Shouldn't be too hard to get this one off too, maybe with some heat.
You could use one of those crappy skins (only the camera one, anyways) to put on the backside lens if you can see the PCB through once you get the gold ring off, assuming you can't just paint it and put it again. I'm sure one of those brands can ship you only what you want, don't remember the name though
I guess you'll have to sand the whole body for the paint to stick to the aluminum and stay there with all the handling? If you can take some pictures of the sanded backside I'd be grateful, cause I think i'll just sand it, paint whatever's left and let it be
The FP sensor should be easy to modify, JerryRigEverything always scratches fp sensors with a blade (like you'd ever get to that point lol) abd they always keep working, so if you need to sand it so that the paint gets stuck to the plastic, you can. I don't even know what those paints are, they probably don't even import them here in Argentina. But from what I'm deducing they won't stick to plastic will they?
Also, I'd advise you to be real careful with the fabric thingy that covers the speakers. I broke one and lost the other one, so I have to clean the speakers with a magnet every once in a while... (workshop fills them up with iron dust). and something JerryRigEverything didn't mention on the disassemble video was that the power button is free-floating once you take it apart (it can't fall off though) and when I was putting the phone together the chassis somehow bent a little bit. Nothing critical but sure looks bad
Choose an username... said:
Well, I took apart my Moto G 2 and while these 2 phones are worlds apart in terms of build quality, all it took was a soft piece of wood and some force to get the camera lens to pop off. was riddled with scratches. Shouldn't be too hard to get this one off too, maybe with some heat.
You could use one of those crappy skins (only the camera one, anyways) to put on the backside lens if you can see the PCB through once you get the gold ring off, assuming you can't just paint it and put it again. I'm sure one of those brands can ship you only what you want, don't remember the name though
I guess you'll have to sand the whole body for the paint to stick to the aluminum and stay there with all the handling? If you can take some pictures of the sanded backside I'd be grateful, cause I think i'll just sand it, paint whatever's left and let it be
The FP sensor should be easy to modify, JerryRigEverything always scratches fp sensors with a blade (like you'd ever get to that point lol) abd they always keep working, so if you need to sand it so that the paint gets stuck to the plastic, you can. I don't even know what those paints are, they probably don't even import them here in Argentina. But from what I'm deducing they won't stick to plastic will they?
Also, I'd advise you to be real careful with the fabric thingy that covers the speakers. I broke one and lost the other one, so I have to clean the speakers with a magnet every once in a while... (workshop fills them up with iron dust). and something JerryRigEverything didn't mention on the disassemble video was that the power button is free-floating once you take it apart (it can't fall off though) and when I was putting the phone together the chassis somehow bent a little bit. Nothing critical but sure looks bad
Click to expand...
Click to collapse
From what i understand, Duracoat will bond to any material, so long as it is degreased and prepped (sanded in this scenario) . So plastic is in. (yay)
i plan to spray the buttons but i do not plan to remove them unless i have to. even the full disassembly is not that hard.
I dont necessarily plan to paint the fp sensor unless i know the finish will not impede functionality. Duracoat may break the functionality, so i might have to be creative. its funny you mention jerryrigeverything's video bc that was my proof of concept for being able to sand the sensor down to not gold color.
on my Droid Turbo, i used to cover the capacitive buttons with clear self adhesive vinyl before i covered the screen with a Skinomi Tech skin. I may just sand the sensor enough for it to no longer be gold and grab some clear self adhesive vinyl to color match, provided that does not break functionality.
as far as sanding/prepping, i plan to emulate the process used in the video here:
and i also plan to take pics and make instructions for the whole process.
The Axon 7 forums dont have any physical mod posts, so it will be nice to put one out there as it is the best device i have owned so far. I used to be a Moto man. but they lost me with the novelty of "mods" and Verizon making boot loaders permanently locked.
My Duracoat should be here by the 30th. i really wish i could buy another color midframe that isnt gold, but ZTE parts are a pain to find.
kitcostantino said:
My Duracoat should be here by the 30th. i really wish i could buy another color midframe that isnt gold, but ZTE parts are a pain to find.
Click to expand...
Click to collapse
Any news? I really wanna see that phone
lol. im watching a couple of 128/6 atm bc one can should do two. depending on how that pans out, i may be able to start on it this weekend.
no news yet. i missed out on the 128gb i was watching. honestly, the hardest part is gonna be having to use my Droid Turbo for a week while the Duracoat cures. fortunately, Turbo has some awesome devs. im still paranoid the midframe will chip easily on the sides, but even after i duracoat it, i will still use a case.
i also have to decide by what means to prep the surfaces. i figure a fine sandpaper, then the truestrip that came with the duracoat. masking the round parts is going to be a pita.
so in essence, its close, but im still deciding my plan of attack. after the holiday, i should be ready to start.
well, i have the turbo updated and im about to go pick up my sandpaper. the camera ring (if i cant find how to remove it) i am leaving gold. i had initially thought id sand the gold off of the camera, but its under the glass. ordered dbrand skins for the camera. if all works as planned, that is a compromise im willing to accept.
the plan as it stands: (commencing this evening)
1) Sand finish of back, sides, mid-frame after disassembly.
2) clean all with Tru Strip (included with Duracoat Aerosol kit).
3) duracoat 5 layers, heat flashing in between coats.
4) (hardest step) leave alone for a week and allow to cure.
I will add pics or a vid when and if time allows while im in the process.
Im using 3m Sandpaper and a sanding block i picked up from Walmart. totally forgot painters tape. back to the store i go. camera on Turbo pales in comparison to Axon 7, so bear with me in this process.
gold finish is thicker than anticipated. i cant get down to bare metal. might say screw it and go with what i got.
400 grit takes forever. camera flash is dead. i tore the black material under the fingerprint sensor. totally pulled the trigger too soon. gonna paint as is. eying broken ones on ebay. if all else goes well (prepped to duracoat atm) either i will live w/o flash and fingerprint sensor (bc of my own haste) or ill buy a grey A7. either way, this back will look great on another axon 7.
also, the gold on the camera lens is a sticker on the bottom side. popped out, and when i went to grab it, thats when the flash fell out.
its probably doomed to look like crap, but progress.
more
verdict: bad ideas ruined a great project. axon is dead. at least, locked in a boot loop. buttons are stuck. buying grey now. lol. lessons learned.
Try using a razor blade to scrape the inside edges of the button holes.