Related
the other day my phone feel of the couch while pluggd into the pc. it stopped chargibg and woukd not connext to pc.
i lost the original cable so ive been using a mini to micro usb adapter for an old cable i had for my g1 which hss worked perfectly.
thought i had broke the sockey on thr phone. had a tmobile shop check it with there cable. it was fine. so boyght a microusb cable.
everything seemed fine. charge light. usb drive worked internet tether. but then the phone ran out of battety while usb tethering. it always stays at 100% before.
with the battery low it woukf rrstart every minute whole plugged into original chargrr.
its charging but very slowly. 15% in 2 hours. checked battery pins. seems fine. i dkd manage to get 37% charge in 30 monutes once irh the phone off.
the phone doesnt even get warm while plugged in. it used to get pretty warm when cuargibg.
tried hard reset. trief reflashig rom. it knows wall charger is in. says charging orange charge light.. but it charges sooo slow...
im stuck. is this a repair jobk
Just got home and tried the new cable in my home PC. ive already lost 1% battery in the space of a few miutes usb tethering....
make sure you have the "don't charge the phone while connected via usb" unchecked. Other than that, sounds like a hardware problem.
i cant find that setting, only do not charge when the phone is on., which is off. Ive just noticed something else. the brightness setting for AC power effects the brigthness when connected to usb. I dont think it knows the difference between ac and usb anymore.
veda_sticks said:
i cant find that setting, only do not charge when the phone is on., which is off. Ive just noticed something else. the brightness setting for AC power effects the brigthness when connected to usb. I dont think it knows the difference between ac and usb anymore.
Click to expand...
Click to collapse
when you plug it into the wall, do you get the menu for: Activesync, Disk Drive, Internet Sharing? If so, then this is true. Really sounds like a hardware issue. I would take it back in and see if they can replace the port.
nope, when i plug it into the wall, no menu. it does seem to know the difference between usb and power. as using the option "when phone is on, do not charge when the pohone is connected to pc" has no effect with the wall charger.
I tried a different wall charger. I have a travel charger which is only rated at 500ma instead of 1amp and it charges the same. I was able to get 100% overnight. woke up after 8 hours to see the green light on, it stays at 100% with the wall charger as long as you leave it alone.
back into the computer, tethering and im loosing battery as if it wasnt connected.
Looks like ill have to dig out my insurance as its not a warranty repair (and also the water damage stickers are red, due to it being dropped in the toilete 3 months ago)
hmmm interesting. phone has been in charger overnight and was at 100% when i got up, pluigged into pc for usb tethering, despite battery dropping the green light is still on.
Ive done some searches on usb micro cables and came across people having problems with some data cables with charging, as some cables cannot cope with the large current required, but they mentioned that there phone would say this and i have seen that on my phone before with my front usb ports on my computer.
Im gonna order a microusb adabter as i have 2 high qualiity usb-mini usb cables from a G1 (which was usbed with an adapter with no problems) and 1 from a tmobile mda varia, same cable.
This has now been solved. After closer examination of the USB mini to micro adapter, it apeared that the 2 outside pins (which are for charging) had been flattened. Looking at the adapter, you could only see the 3 middle pins, but with a torch you could see that the oiutside pins were compelty flat. from droping the phone its oviously twisted the connector resultinin in flatting those pins.
I went back to tesco and bought the same USB kit which comes with a mini USB cable and several converters to fit different phones.
AFter hooking up the cable and micro usb adapter to my PC, my phone was within minutes showing increase in battery charge. After a few hours with usb tethering enabled and watching videos online im up 2-%.
The cable i bought for £7.99 which is micro usb though doesnt mention any HTC phones (mostly nokia) will connect perfectly for data transfer and the phone appears to say its charging. It looses power suggesting insuficient charge current. Maybe its the rom im using disables thsi warning as i have seen this before when i connected my phone to the front usb ports, but it works fine with the back.
So, it seems i have not damaged anything apart from the usb adapter i was using.
All is well, and im charging at a fast rate with USB while tethering.
Please close this trhead as it is resolved.
Final update. After several days i have been usb tethering and charging absolutly fine. Using 1amp charger charges fast!
Even from a dead battery can plug into usb and have the phone bootup.
Sent from my HTC HD2 using XDA App
Went to sleep last night with my Atrix plugged in as I normally have had all my phones, was playing with it right before I went to sleep and everything worked just fine, woke up this morning and the phone will not power on!
First tried to power it on unplugged and the green light flashed for 2 seconds, and nothing happened. Okay, weird, but I'll go with it. Plugged it in, and the green light stays on now until I press the power button! Once pressed, it flashes off, flashes on for 2 seconds and stays off. Nice. I thought the green light meant it was fully charged - when I woke up this morning, it had no green light on, but it was plugged in just fine all night - grabbed my Jawbone ERA and plugged it in to the charger I had the Atrix connected to and it started charging right away, so I know it works....
Pulled the battery, tried plugging it in and power it on without the battery. Nothing. Tried putting in the battery and plugging it in again to "jump start it" as I had done yesterday when I first got it - apparently you can't just charge the thing when connected to a laptop if the phone is off, it will power on even if you power it off again! Nothing.
What the hell happened in it's sleep? I KNOW rooting it didn't cause sleep death.... This thing doesn't have a custom ROM or any undervoltage adjustments, so why the hell is it acting up??? Damnit, right when I got EVERYTHING set up the way I wanted it too.... can't bring it in to the store and give it up with all my personal stuff on there now, I need this thing to power on to wipe it first!!! I'm leaving it connected to the laptop with the green light on for a while and will see what happens in an hour or so....
EDIT - just searched for and tried to hard reset the phone from this thread, the phone still won't even power on to get to the recovery screen!!!
UPDATE - see below and use the SUPPLIED Moto AC charger or at least one with over 5.0V - NOT a PC and NOT a USB hub!
use the charger that came with the phone. My old HTC ones won't charge the phone for some reason. I bet your battery is just dead.
Did you use the provided charger? I tried plugging my Atrix in to the charger I used for my N1, and found that it did not provide enough current. With the old charger, after the phone died, I had similar symptoms where the green light would flash but phone would not come on. Plugged it in with the Moto provided charger, and 5 minutes later all was good...
I had the same problem. Thought I was gonna have to take it back to the store. I don't know what the problem was but I took the battery out for 5 minutes. Then I plugged it into the wall charger(wouldn't work with PC). I didn't turn it on for 30 min, just left it on the charger. Then I hit the volume rocker and it showed the battery charging symbol which it didn't do before. And then I was able to power it on
Same thing here. I purposely drained my battery on the first use. Plugged the usb cable into the PC and nothing. Same blinking green light with no response. I also thought I'd have to return the phone. Then for S & Gs I plugged it into the wall charger and it came to life. Once I got the battery charged a little bit I plugged it into the PC and it started to charge again. Don't know why, but it worked.
Have been running around the house trying to find valid outlets, and that does indeed appear to be the problem. I found it out the hard way though, should have kept an eye on the thread - used a power outlet instead of a PC USB connection and the screen fired right up! Yes, the phone showed the battery with 0% in it, but at least the screen finally came on!
How I have my phone set up normally is connected to my charging valet on my dresser, connected with a 15 foot USB cable that plugs directly into my desktop. Since the extension is good for just one USB connection, I have that connected to a USB hub and then a MicroUSB cable connects my phone from there. The Captivate, and all the other phones I've ever used, not to mention my Zune and Jawbone ERA, all eat that up and have no issues since the USB hub is powered not by the computer (seven USB cables is just too many for a single PC connection) but by the power outlet in the charging valet. I wonder if the hub is distributing the power requirement for each device and the Atrix needs more than others.
I also figured out that the Moto charger has a 5.1V output on it, as does my Jawbone AC charger. Now I need to start making sure that my each one of my chargers in the cars I own has that same type amount of juice too! You go up 29% in battery capacity and so do the requirements to charge it, huh?
Thanks for all the help, marking this SOLVED....
I used the charger in my bedroom that I've used for the Captivate and others before it and it didn't provide enough juice to charge the Atrix. It quickly switched between charging and not charging. I still had 40% battery showing when I woke up though which was nice. It had been off of charge since 10am yesterday.
Plugged it into an HTC charger and it's fine. The one that didn't work is not a modular charger so the power cord is hard wired to the plug.
Alright, a quick update.... Got the phone charged to 100% while it was off and plugged into the AC outlet with the Moto charger. Put my SIM card back in it - couldn't be without a phone all day! - and fired up the Atrix. Went to Battery Info to see what the status is and while plugged into my USB hub, it says
Battery Status: Discharging
Power plug: USB
....
Battery Voltage: 4124 mV (or 4.124V)
Click to expand...
Click to collapse
What the hell? Then I went right after that and plugged it into the Moto AC charger, it says:
Battery Status: Full
Power plug: AC
....
Battery Voltage: 4207 mV (or 4.207V)
Click to expand...
Click to collapse
Why are POWERED USB hubs and PCs not strong enough to charge the phone? I tried ALL my outlets in my vehicles just now and they ALL show full battery status and plugged into AC! Who screwed this up????
GarciaM25 said:
Why are POWERED USB hubs and PCs not strong enough to charge the phone? I tried ALL my outlets in my vehicles just now and they ALL show full battery status and plugged into AC! Who screwed this up????
Click to expand...
Click to collapse
Did you download the PC Charging Drivers that Motorola requires you to have in order to charge via PC and USB cable? If not, look here.
Battleship said:
Did you download the PC Charging Drivers that Motorola requires you to have in order to charge via PC and USB cable? If not, look here.
Click to expand...
Click to collapse
Wait, you have to have specific drivers on the PC so that the phone will allow a power cable (let's not even worry about it being a USB cable for a second) to charge the phone properly? I have the Motorola Media Link software installed, and that has a ton of drivers on it, that wasn't enough? MORE drivers are required to charge a cell phone? This is madness!
Sorry about the necromancy, but had this problem myself but it is NOT due to a lack of voltage. Thought I'd actually solve this, the problem is CURRENT.
USB2 ports will only ever supply 500ma which simply isn't enough to charge the atrix when it's dead. USB2 powered hubs won't supply any more than this either to meet the USB2 spec. The fact that the AC adapter works is because they tend to have a higher output current in the region of 1-2 amps (you may notice the phone, or any other device for that matter, charges faster with AC adapters for this reason).
On a similar note, cheap car chargers only output 500ma. I know with my desire I can have it plugged in and it charges, but if I use GPS it actually draws more current than it can charge at resulting in the battery draining (albeit, slowly).
So, make sure you have a higher current AC/Car charger, or alternatively, plug it into a USB3 port to charge as USB3 spec allows 900ma (some mobos output up to 1A) which is enough to charge the Atrix.
Stewge said:
Sorry about the necromancy, but had this problem myself but it is NOT due to a lack of voltage. Thought I'd actually solve this, the problem is CURRENT.
Click to expand...
Click to collapse
Hey, no problem, if there's something I misstated, then please, correct it!
Stewge said:
So, make sure you have a higher current AC/Car charger, or alternatively, plug it into a USB3 port to charge as USB3 spec allows 900ma (some mobos output up to 1A) which is enough to charge the Atrix.
Click to expand...
Click to collapse
Not sure about this..... It's been about a year since I got all my USB3.0 gear, and I was super excited about it because I thought that my phone would charge ridiculously fast because of the added output, but I remember reading that 3.0 uses extra pins and those pins account for the added voltage and bandwidth of the cable - we don't have those extra pins when you step down from 3.0 to 2.0, so we lose the ability to charge devices faster as a result. I don't know if I actually proved that theory, but after I read up enough on it, I thought I just didn't have to with that knowledge..... again, correct me if I'm wrong, I've got a lot of 3.0 gear here!!!
GarciaM25 said:
Not sure about this..... It's been about a year since I got all my USB3.0 gear, and I was super excited about it because I thought that my phone would charge ridiculously fast because of the added output, but I remember reading that 3.0 uses extra pins and those pins account for the added voltage and bandwidth of the cable - we don't have those extra pins when you step down from 3.0 to 2.0, so we lose the ability to charge devices faster as a result. I don't know if I actually proved that theory, but after I read up enough on it, I thought I just didn't have to with that knowledge..... again, correct me if I'm wrong, I've got a lot of 3.0 gear here!!!
Click to expand...
Click to collapse
There are indeed extra pins in the USB3 standard but these are to transmit data only. The original USB2 data pins are only there for legacy support and USB3 transmissions use the extra lines. There's still only the 1 VBUS pin which supplies the +5V power. There's also no harm in offering higher current on the connection as a device will only ever draw as much current as it needs until it tops out the supplier, not the other way round
EDIT: Another solution could be to use a splitter cable (common with 2.5" drives)so you can draw from 2 ports, but with a micro connector. I've never actually seen one with USB micro but a quick look on ebay says they do exist
nsaia said:
Same thing here. I purposely drained my battery on the first use. Plugged the usb cable into the PC and nothing. Same blinking green light with no response. I also thought I'd have to return the phone. Then for S & Gs I plugged it into the wall charger and it came to life. Once I got the battery charged a little bit I plugged it into the PC and it started to charge again. Don't know why, but it worked.
Click to expand...
Click to collapse
Hi, can I know that when you plug it into the wall charger, is there any light on? Mine has no light on when plug to wall charger. But I can get the light green when plug into PC USB. Can you share that?
cscmf99 said:
Hi, can I know that when you plug it into the wall charger, is there any light on? Mine has no light on when plug to wall charger. But I can get the light green when plug into PC USB. Can you share that?
Click to expand...
Click to collapse
This is the exact same issue that I am facing now. Did you ever manage to find a solution for this problem?
atrix 4g not coming on
Is there any real fix to this issue i have search high and low and all i am seeing people talking about the battery id dead ... i have two battery that is fully charger and the phone still not coming up.
Hi all, sorry that im posting after two years ago but i am facing exactly the same problem, but i plugged it in my USB port, wich i think its a usb2, and i got the screen on but the cellphone did not say charging instead of that was connect your charger, and it was lower than 3% then it turned off. What can it be a solution??
None of the avobe solutions worked?
Which rom/kernel are you using?
I too have this same issue. My Atrix won't come on. I have 2 of the same phone. I tried the charger and cable from both phones. Neither work. When I first plug it it, the green light comes on for a few seconds then it goes out. I even opened the phone and removed the battery. Used a voltage tested and found my battery has 3.7 volts. Thats almost 100% charge. So it not a problem of power. I plugged the phone to my computer and same green light for a few seconds then gone. Won't do anything. No battery display or anything. I even did the simulated battery removal procedure. Didn't work. Is there anything else I can try? Can't get to recovery mode without display unless someone has a fix for that?
Hello everyone,
I have my 32GB TF201 with docking that I purchased 3 weeks ago. After I purchased I was able to charge my table directly thru outlet twice and once thru the dock. This week the tablet ran out of battery. I plugged it to the outlet with an empty battery and yellowish light was on. In the morning (after 6 hours of charging) I checked and the light was still yellowish. I said 'what the hell' and left home for work. When I came back I checked and saw that the battery was only charged to ~9%. I re-checked the outlet and it was not charging. The battery icon appears when I plug the cable but the status is 'Not charging' and it actually is not charging. I could then charge the dock thru the same outlet and usb cable up to 100%. I also could charge the tablet thru the dock's battery. the only problem is between the charger and the tablet itself. I will still take it to the service but I can still listen to ideas to check in the weekend.
Thanks a lot.
You probably have a busted charge port on the tablet itself. Try plugging the tablet to the computer and see if it registers. If not, more than likely the charge port on the tablet is broken.
Sent from my SPH-D710 using xda premium
huynhc said:
You probably have a busted charge port on the tablet itself. Try plugging the tablet to the computer and see if it registers. If not, more than likely the charge port on the tablet is broken.
Sent from my SPH-D710 using xda premium
Click to expand...
Click to collapse
that was the one thing I did not check and I will today. but the tablet is being charged from the dock that is connected thru the same port.
I am having the same no charging issue, but I do not have a dock. The device recognizes the computer just fine when I plug into that, but into the wall, I get nothing. Even when connected to the computer, all the connection info pops up (usb debugging, asus sync, etc) but it does not charge. Problem started this morning.
Cayniarb said:
I am having the same no charging issue, but I do not have a dock. The device recognizes the computer just fine when I plug into that, but into the wall, I get nothing. Even when connected to the computer, all the connection info pops up (usb debugging, asus sync, etc) but it does not charge. Problem started this morning.
Click to expand...
Click to collapse
sorry to hear that but still good to know that I am not the only one I will update this thread when and if I get a response from the service. please let me know if you find the reason or a solution to this problem
cheers
yuzereroglu said:
sorry to hear that but still good to know that I am not the only one I will update this thread when and if I get a response from the service. please let me know if you find the reason or a solution to this problem
cheers
Click to expand...
Click to collapse
Okay, I first had this issue last night. Unplugging and plugging it back in fixed it at the time. Then this morning, I couldn't get it to charge at all (replugging it in multiple times) via AC or USB (though it did recognize the other USB things like it should). I managed to find a dock in stock nearby finally and picked one up today. Plugging the tablet into the dock charges off the dock like it should, and plugging in the dock charges it like it should. Now, miraculously, when I unplug the tablet from the dock and plug it back into the wall via AC, it works again.
So, don't know what exactly the issue is, or how exactly to fix it, but at least it seems to have fixed itself for the moment. And, now I have the dock if this happens again
hey there. i took the tablet to the service but to my luck the unit is flagged as 'defective on arrival' and I had to return it. I guess it was a ahrdware issue. I could not take a new one since the reseller was out of stock of TF-201. I am waiting for it to become available.
Wow - my tablet would not charge at all last night as I ran out of battery. I tried all the outlets in my hotel room and my PC, but it just seemed like the charge port was dead. I noticed that the trim around the charge port was a bit deformed, so the plastic part that abuts the bezel was not straight.
Anyways - I get to the office this morning and plug it in and now its charging - whew! This is eventually going for RMA since the HDMI is completely dead, and now it does seem the charge port is a bit loose. I am concerned it will happen again just when I need it!
Very frustrated with the quality issues - it's just harshin' my buzz with this tablet.
I've switched through three different primes (with issues unrelated to this) but I seem to notice that all of the chargers are like this. It seems like a security feature or bug (not sure) but if you keep the charger plugged into the outlet, it auto shuts off the charging adapter after being plugged in for a prolong period of time. If you take the charger out, leave it unplugged for an hour or two, then plug it back in. It will work again. All three of the primes I got do this. So I just remember to unplug the charger and don't leave it plugged in and the issue doesn't seem to happen anymore.
btw just a heads up:
- USB won't charge on computers unless your usb port is usb 3.0. If your usb is 2.0 it will only charge on idle (which you won't be able to tell really)
- Dock won't charge the tablet unless the tablet runs around 75% battery (sometimes higher sometimes lower) its in the FAQ
Cayniarb said:
Okay, I first had this issue last night. Unplugging and plugging it back in fixed it at the time. Then this morning, I couldn't get it to charge at all (replugging it in multiple times) via AC or USB (though it did recognize the other USB things like it should). I managed to find a dock in stock nearby finally and picked one up today. Plugging the tablet into the dock charges off the dock like it should, and plugging in the dock charges it like it should. Now, miraculously, when I unplug the tablet from the dock and plug it back into the wall via AC, it works again.
So, don't know what exactly the issue is, or how exactly to fix it, but at least it seems to have fixed itself for the moment. And, now I have the dock if this happens again
Click to expand...
Click to collapse
This is the exact replication of what's occurring with my TF201 with the exception that it is still not charging directly plugged into the tablet after I remove from the dock.
weird trick
I think this might be due to how some devices recognize power, i have the same issue with my iPod touch. I found that if you take the charger wire with adapter attached and plug that into the tab, then plug that into the wall it should normally work. My brother was having this issue also with his dock not charging, and this method makes it work.
Well, called ASUS support and got an RMA to send it in. Apparently something's wrong.
C series serial number prime worked for three days now won't take a charge. Device will connect to pc or mac via cable, just won't take a charge. Any ideas for me?
askmattrix said:
C series serial number prime worked for three days now won't take a charge. Device will connect to pc or mac via cable, just won't take a charge. Any ideas for me?
Click to expand...
Click to collapse
there have been other threads about this. usually its the charger overheating and putting it in a ziplock in the freezer, resets it.
Mine did that too, just leave the charger and everything unplugged from the wall for a day. That fixed mine.
Sent from my ADR6425LVW using XDA Premium.
The other issue I've seen is poor contact in the USB socket on the wall adapter. I had to unplug the usb cable from the wall adapter. Then, look at the usb socket on the power adapter. The gold pins are the usb contacts. Directly opposite of them, there should be two silver prongs. I had to use a small flat blade screwdriver to pry both of them out a little further to ensure they did their job of firmly pushing the usb cable against the socket's usb contacts. Once I did, my TF201 was able to get charge from it, again.
If you decide to replace the wall charger, I believe Fry's and Office Depot stock the asus charger.
Same thing for me.. PC recognizes it as a media device, but will not charge with wall charger. Wall charger works with my HTC Phone, so it works.
I don't think it has anything to do with the latest update, since the Dock wont charge either, and there's no OS in that, right?
Just experienced this today. I have had it unplugged for about 10 hours now, we'll see if it charges.
I had the same issue few days after I got my prime. I connected my sgs to the charger and it worked. Then connected the prime and voila-works.
askmattrix said:
C series serial number prime worked for three days now won't take a charge. Device will connect to pc or mac via cable, just won't take a charge. Any ideas for me?
Click to expand...
Click to collapse
Which C model do you have? C1,2,3? Just asking.
Johnny0906 said:
Which C model do you have? C1,2,3? Just asking.
Click to expand...
Click to collapse
C1. There are some good suggestions here I need to try.
Wrap it in a towel and bang it against a table. That will fix it usually. Then get some pc heatsinks and some arctic silver adhesive and you can attach them to the charger to keep it from happening again.
The plug has two options, 5V (standard for USB?) and 15V. I used the plug on my old HTC phone (Ozone) and then plugged it back into my Prime and it worked. Thanks for the great tips guys.
Since the charger works in two modes, I wonder if some charges became confused and started dishing out 5V when they should be dishing out 15V. Thoughts?
G37 said:
The plug has two options, 5V (standard for USB?) and 15V. I used the plug on my old HTC phone (Ozone) and then plugged it back into my Prime and it worked. Thanks for the great tips guys.
Since the charger works in two modes, I wonder if some charges became confused and started dishing out 5V when they should be dishing out 15V. Thoughts?
Click to expand...
Click to collapse
Hi, I got the same problem. The charger indeed seems to be stuck in the 5V mode, since, when plugged in the tablet does get charged, even though it is not indicated, but very slowly. It is charging as if it is plugged in to a pc.
I tried plugging it into (old) phones, but I still can't seem to get it to switch back to the 15V mode.
The freezer didn't help either.
Any other suggestions?
I waited about 4-5 hours before plugging into my old phone. My other suggestion is to allow the phone to charge for a short bit (30 minutes) unplug and wait, then plug into your Prime.
I have a feeling that its a transistor toggle that isn't flipping at the correct voltage.
I've had the same problem yesterday. In my case the problem was with the charge socket on the keyboard itself. Some copper pins were deformed and that stopped the device charging. I took a magnifying glass(also for checking if any of the copper pins are bend) and a small tool to bend them back. After this it charged again. Hope this helps.
My charger suddenly stopped working from today. The Prime is detecting the connection as the screen turns ON but it is not charging. I charged my sensation using the same adapter and USB cable and it is working fine. Why can I not charge Prime via PC like phone? Is it possible? I am in India and not sure if the power adapter is easily available as Prime is not yet launched in India.
Kindly suggest.
Thanks in advance.
Hi,
I've started to have this problem today, plug it in and it does come up with the charge icon but it doesn't charge - or doesn't seem to.
However I left it connected last night from midnight until 8am this morning and it went from 13% to 17% so it is charging VERY VERY slowly although the unit doesn't actual seem to think it is.
I have it plugged in to my phone right now and its working perfectly, I borrowed the charger to my g/f last night to charge her iphone and i'm thinking this might have done something to flip the voltage as since then it isn't working.
Anyone have any ideas on this??
Kevin
thornd7 said:
The other issue I've seen is poor contact in the USB socket on the wall adapter. I had to unplug the usb cable from the wall adapter. Then, look at the usb socket on the power adapter. The gold pins are the usb contacts. Directly opposite of them, there should be two silver prongs. I had to use a small flat blade screwdriver to pry both of them out a little further to ensure they did their job of firmly pushing the usb cable against the socket's usb contacts. Once I did, my TF201 was able to get charge from it, again.
If you decide to replace the wall charger, I believe Fry's and Office Depot stock the asus charger.
Click to expand...
Click to collapse
I had this problem a couple of weeks ago and completed the same as above works well
Gilbo12 said:
I had this problem a couple of weeks ago and completed the same as above works well
Click to expand...
Click to collapse
But if the charger works fine when charging a phone it cant be the connection at fault..
It does seem to me that the power it is outputting has dropped especially the I managed to gain 5% over the course of a night where WIFI was off and screen was off even though the charge icon doesn't come up.
Is there a way of forcing the charger back in to 12v mode??
damnit... I had the same problems a few days ago and I thought it was in the cable instead of the charger... not realising the charger has to put out 15v instead of 5v.
Does this mean the Transformer won't charge with for example, my HTC charger?
I totally messed up my cable, because I thought it was broken... when I opened up the USB plug, I noticed the yellow wire was not connected anymore, but this didn't solve anything. Eventually I messed up the cable that bad, that I've ordered a new one from ebay... but when I read this... I should have just banged the charger a few times... shait.
funfair said:
damnit... I had the same problems a few days ago and I thought it was in the cable instead of the charger... not realising the charger has to put out 15v instead of 5v.
Does this mean the Transformer won't charge with for example, my HTC charger?
I totally messed up my cable, because I thought it was broken... when I opened up the USB plug, I noticed the yellow wire was not connected anymore, but this didn't solve anything. Eventually I messed up the cable that bad, that I've ordered a new one from ebay... but when I read this... I should have just banged the charger a few times... shait.
Click to expand...
Click to collapse
Has anyone actually ever managed to fix this problem? I've just contacted ASUS about it to see what they say - hopefully they'll ship me out a new charger plug or something, what a useless charger!!
My GT-i9300 seems to only recharge when plugged into a mains charger.
Until recently all was fine, afaik no updates... then
I travel alot, and use a car charger to maintain battery... it just stopped working, first thoughts were the cable..;. but I have 2 phones and the cables work with the other phone (bought new ones anyway.. just in case.. you can never have to many cables).
at home we have (amongst other things) a 2amp multi usb hub, it has little lights to show which socket is active, when the phone is connected the phone does not charge and the hub does not register the connection.
.. so I'm thinking the phone microusb is faulty... I carefully wiggle it to see if it connects... but get nothing.
however, the samsung microusb charger that came with the phone does still charge the phone.
My feelings are that my phone has suddenly become fussy about what charges it..
I've done a search and found mention of Googy max kernel for the charge control feature
however before I do this please, any tips, suggestion WHY this might have suddenly happened? and any alternative remedies. Thanks
btw: using Carbon-kk-nightly-20140302-0518 with no problems previous to this... except a dialler issue.