Does anyone know of a way to run the phone without having the battery and mainly using the charging port?
I'm currently using CM7.03
I don't want my battery to overheat while I have it on tethering. The battery temp according to hidden mode went up to 48.0C, battery status "Overheat" =[
It may not be possible with our phone.
I tried it on mine, using a car rapid charger and the standard wall charger, and neither worked, so I don't think that's the problem.
Follow these steps then you can use moble without battery:
1. Start your phone (boot up)
2. Plug charger
3. Remove battery
=> Your phone is working normally.
(may be you have to remove the case before plug charger)
Try it
Related
I have been charging my phone via usb connected to my laptop ever since I got the phone and I noticed I was not getting the amazing battery life on Nero v3 that others reported. I ran across a thread that said something about charging from the stock wall charger to improve your your battery.
Well I decided to drain my battery after installing Nero v4.1 and charge it fully on the wall charger. Since doing this I have 51% battery at a point in the day when I would normally have 30% or less.
My question is has anyone else noticed this? Or tried it?
Sent from my SGH-T959 using XDA App
Your laptop may be limiting the current to the USB in power saving (typically if running off battery). So yes it is entirely possible for that to happen, and it would confuse the phone. Then it would not be able to re-align its battery capacity guess until it starting drawing from it again.
You can try turning off the option on the USB ports/controllers that says "Allow windows to turn this device off to save power". (If your using windows, I have not seen MACs with the power save issue).
Note: Some PCs use "hubs" for the external USB interfaces (ports). This can also cause a lower current to non self-powered devices.
It was working fine before I went to bed last night, then I let it charge for the night since that battery was at about 4%, But this morning it won't turn on at all. The battery feels warm as if its been charging but nothing seems to be making it turn on. Any ideas?
re: No Poweron
labou_7 said:
It was working fine before I went to bed last night, then I let it charge for the night since that battery was at about 4%, But this morning it won't turn on at all. The battery feels warm as if its been charging but nothing seems to be making turn on. Any ideas?
Click to expand...
Click to collapse
If it was my phone here is what I would do.
First I would see if the phone charges the battery by putting the battery into
the phone and plug the usb cable from phone into the wall charger or into
the computer.
If the display on phone shows a picture of a battery charging let it charge
for an hour more or less and try turning on the phone.
If the phone is not charging the battery I would purchase a cheapy battery
charger and battery combo on eBay.
You can find this combo on eBay for less than $8 bucks shipped for both the battery and charger:
http://www.ebay.com/itm/1800m-BATTE...045605?pt=PDA_Accessories&hash=item43aa9a4465
(even if you decide to return and exchange the phone its still a good thing to have a spare battery and charger)
Check it out.
Good Luck!
labou_7 said:
It was working fine before I went to bed last night, then I let it charge for the night since that battery was at about 4%, But this morning it won't turn on at all. The battery feels warm as if its been charging but nothing seems to be making it turn on. Any ideas?
Click to expand...
Click to collapse
are you on cm7? not sure about the s2 (never had the issue), but i know that on the infuse, there was a problem (or maybe it was intentional) with low power charging mode (phone wouldn't charge when off).
i think this can be solved by trying to charge the phone via your computer usb, as opposed to your OEM wall charger.
Thanks for the suggestion. It definitely isn't showing the picture of the battery when its plugged in to the wall or the computer. I'm debating the battery charger combo you linked.
I actually am. But I have it plugged to my computer and nothings changed.
Time for some trouble shooting.
Start eliminating possibilities. You need to determine where the problem is.
From what you say, it seems possible that the battery is completely discharged but not recharging. That could be a bad battery or it could be the phone.
If you know someone else with an SGS II, try inserting their battery temporarily to see if your phone will boot. If you don't know someone else, maybe you can borrow a charged battery from the store where you bought it.
Continue on until you pinpoint the problem.
Do NOT buy a "cheapie" battery for your SGS2. Unless you want to eisk causing damage. The stock battery for the SGS2 has NFC technology built into it. Using anything other than OEM could cause damage/performance issues to your phone, and void the warranty.
Sent from my SAMSUNG-SGH-I777 using XDA Premium App
Have goh tried a battery pull? Unplug the phone, pull the battery and let sit for a few minutes to allow tbe IC's to discharge. Put battery back in and try powering up the device. Good luck.
Sent from my SAMSUNG-SGH-I777 using XDA Premium App
Similar issue and got phone fixed finally
Have had similar issue as yours. Cable charger was plugged into the phone to be charged at night and was surprised to find that the phone became hot and battery was not charged at the next morning, in fact the battery level got lower than it was before charging.
Notes:
- ROM in use: AOCP version 7.2 (Android 4.4.2)
- Kernel in use: Version 3.0.101 [email protected] #3
Here are some tests done and the observations after getting a charger with a slot to place the removed battery for charging:
1. Charging via USB cable connected to PC:
- With the phone turned on, battery charging icon is only displayed after some wiggling at the charging port. The phone got charged further to 100% when the initial remaining battery level is 90%. However, when the initial battery level was less than 50%, the battery level continued dropping ALTHOUGH the battery charging icon was displayed.
- With the phone turned off, battery charging icon is only displayed after some wiggling at the charging port. When the initial battery level was less than 50%, the battery charging icon displayed only a battery level of 1% and the battery level did not increase at all after 15 minutes of charging.
Initially suspected that it was a dead battery issue and bought an i9100 battery, I thought it was a compatible battery at first. With the i9100 battery, I repeated the above tests.
2. Charging via USB cable connected to PC:
- With the phone turned on, battery charging icon is only displayed after some wiggling at the charging port. The phone got charged further to 100% when the initial remaining battery level is 90%. However, when the initial battery level was less than 50%, the battery level continued dropping ALTHOUGH the battery charging icon was displayed.
- With the phone turned off, battery charging icon is NOT displayed but the phone screen flashed continuously, and at times the phone is turned on automatically as the USB charging port is inserted. When the phone is turned on, the charging proceeded as the above sentence.
Upon searching the forum, I found that i777 has a different battery with NFC chip and i9100 battery has reported to cause issues during charging on i777 devices. There was also a Chinese forum which mentioned that the battery compatibility issues should have been overcome in ROM with Android version 4.0 and above.
I then bought a new i777 compatible battery and tested charging via USB cable. The observations are same as the first battery as at 1.
With the battery issues possibility eliminated, I approached a phone technician to examine the phone by telling him that the phone couldn't be charged and the battery level continued dropping even with the battery charging icon displayed. The phone technician then thought that the USB charging port to be the cause of the charging issue and replaced it. The replaced part is the small metal housing where the USB cable is inserted, and is replaced by heating the old metal housing and replacing it with new part by soldering.
The phone could be charged with USB cable as usual after the part replacement and all the batteries are found to be still working fine. Ended up with 2 i777 batteries and a i9100 battery, may be I could continue using this phone for at least another 5 years down the road.
Hi as stated my question is NOT to know how many of you experience charging that takes too long, but is there a SOLUTION for it?
I am using a desire s, it used to take 2hours 30min(from 15%-100%) but now a days it takes close to 5 hours to fully charge.
I've read many thread with similar problem but non seem to be able to find the solution.
I doubt it is battery related issue as i got this phone together with my friends and theirs has no issue like this.
I've tried :
1)full wipe
2)different rom(s)
3)different kernel
4)battery stat wipe
5)different charger(both are htc)
ps : I've post this in DesireS Q&A but did not get any solution.
How are you charging your phone: USB to PC it via wall charger? If it's taking longer than usual turn off the phone. I've found that this sped up the charge dramatically! By doing so, you can also see a battery simulation on the screen showing the charging process.
Also, if you're charging vis USB, the requirements are 5 volts from a USB connector. But the problem is amperage. Wall chargers can supply up to 1 amp (some will supply more, but you don't want more for a phone), while many computers will only supply 500 milliamps out of a USB connector. Thus the phone (battery) will charge faster with a higher amperage. If that doesn't do any good, you may have a bunk battery or some kind of hardware issue...
Sent from my MB865 using xda's premium carrier pigeon service
I am using wall charger. It seems consistent to charge slower at around 70% then speed back up at 90%. Are u sure that this is a symptoms of a spoiled battery?
To me(an accountant not a technicians) it seems like the "smart" phone is tell it to charge slower at 70%.
Sent from my Desire S using xda premium(nah dun have the money to buy premium)
Same problem
I have the same problem, first when I bought my SE x10 mini pro. It charged in 1.5 hours but nw it takes about 3 hours. I don't know the reason but I'm trying to find out how to solve this problem.
I'm not entirely certain its a case of bad battery, but it does sound a bit suspicious. If you're feeling up to it, you can try this: (it's worth a shot.)
If, after rooting or more likely that case after flashing a new rom, you often have battery reporting errors and re-calibrating the battery along with some steps I will outline for you below will ensure that your battery is getting a full charge, and the battery reporting accuracy is right on.
1. Take the case off your phone (one of the latter steps involves taking the battery out from the phone while it's plugged in. Make sure your case won't stand in the way.)
2. Install Battery Calibration app from the market
3. Plug in your phone to charge while it's on, wait till it gets to a 100%
4. When the charge is 100%, open the BatteryCalibration app and lookup what the charge is in MV while at 100%. Write it down.
My Atrix 2 was showing ~3400MV while at 100%, which is definitely not the maximum capacity.
5. Discharge your phone completely until it shuts off.
A good way of doing this quickly is by turning on wifi, and a video player.
6. Without turning on the phone plug it into a wall charger and let it get to 100%
7. When it's at 100%, without unplugging it from the wall charger, take off the battery cover, and take the battery out.
Your phone will "reboot" and show a Missing Battery icon.
8. Without unplugging the phone from the wall charger or turning it on, put the battery back in and wait until the phone recognizes the battery.
9. Your battery should now be recognized by the phone, and showing a charge % significantly lower than 100%.
Mine showed only 5%.
10. Let it sit there charging for 2-3 hours (or more).
My phone wouldn't charge past 10%, but yours might. The numbers don't matter much as the phone is definitely getting additional charge that could have been lost while flashing ROMs, etc.
11. After 2-3 hours (or more), turn the phone on while holding the volume down button and get into CWM.
Do not disconnect it from the charger still!
12. Wipe battery stats and reboot.
Do not disconnect it from the charger still!
13. When the phone turns on, go into Battery Calibration app again and look up your MV numbers -if you were like me, they should be significantly higher than before. After this whole process I had 4351MV at 100%, comparing to 3400MV before calibration.
Do not disconnect it from the charger still!
14. Make sure your wifi and data connections are off. Now finally unplug the phone from the charger.
Go to bed, let your phone sleep too.
The next morning, use your phone as normal throughout the day. Then when it comes time to charge again, see if that does anything for your battery life and/or charging times...
Sent from my MB865 using xda's premium carrier pigeon service
I liked your current charge curve..
bump
ps : i did try out #5 but no success
best way is shut down device when charging
Sent from my GT-I9300 using xda app-developers app
Yes is charges quickly when the phone is off, but what if i am expecting a call or some sort. Could it be a script some where to tell the phone when should it start slow charge or something similar?
So i just played with Custom ROMs to find the best for me...
But from one point my Phone f*cked up the battery detecting...
CM9 and CM9 detect the battery at 45% and then he Level instantly just drop to 0%...
I cant even restart my phone, so i guess the battery really went out...
So how can i fix, that the ROM would not detect it 45% but 3-4% ?
And let me fully chage my phone ?
Stock rom Always Detect it 100% and then randonly the phone shut down in random times (cuz it drops the level to 0%)
I've tried the "Fully-Charge, Fully-Discharge" But the ROM still detect the Battery wrong...
Even tried to delete the battery stats...
Any solution, or idea ?
I currently use CM with the built-in CM9 kernel...
I think its battery problem.use a new battery.ur prblm will be solved
Sent from my WT19i using xda premium
RabirX said:
So i just played with Custom ROMs to find the best for me...
But from one point my Phone f*cked up the battery detecting...
CM9 and CM9 detect the battery at 45% and then he Level instantly just drop to 0%...
I cant even restart my phone, so i guess the battery really went out...
So how can i fix, that the ROM would not detect it 45% but 3-4% ?
And let me fully chage my phone ?
Stock rom Always Detect it 100% and then randonly the phone shut down in random times (cuz it drops the level to 0%)
I've tried the "Fully-Charge, Fully-Discharge" But the ROM still detect the Battery wrong...
Even tried to delete the battery stats...
Any solution, or idea ?
I currently use CM with the built-in CM9 kernel...
Click to expand...
Click to collapse
How old is the battery? What charging cable are you using and what is the cable plugged into?
If the battery is more then a year old it could be 'tired' and not holding a charge correctly (trying another known good battery in your phone will determine this, as will trying your battery in another phone, and if it works well you may have more issues to deal with). If you got the phone second hand, you have no way of knowing the battery's history. Repeated overcharging is also not recommended, as well as leaving the battery in very hot places as it can damage the onboard circuitry in the battery.
Cheap aftermarket (non OEM) USB cables are not that great imo, they are generally not as well made and soon get loose connections, resulting in poor connectivity (charging with a bad cable can also damage the battery). Always use the original cable or a good quality aftermarket one, like Belkin.
Charging the phone from a USB port on a PC or laptop (and/or via a USB hub) is not as efficient as charging it directly from a wall mains USB adapter, because the power often gets interrupted. Ideally for the best charge you should turn the phone off and use a wall/mains socket USB lead, so as give a direct, constant, power supply to charge a battery. A typical full charge is done in two hours. If you charge this way and the battery still has issues buy a new one.
smirnofred said:
How old is the battery? What charging cable are you using and what is the cable plugged into?
If the battery is more then a year old it could be 'tired' and not holding a charge correctly (trying another known good battery in your phone will determine this, as will trying your battery in another phone, and if it works well you may have more issues to deal with). If you got the phone second hand, you have no way of knowing the battery's history. Repeated overcharging is also not recommended, as well as leaving the battery in very hot places as it can damage the onboard circuitry in the battery.
Cheap aftermarket (non OEM) USB cables are not that great imo, they are generally not as well made and soon get loose connections, resulting in poor connectivity (charging with a bad cable can also damage the battery). Always use the original cable or a good quality aftermarket one, like Belkin.
Charging the phone from a USB port on a PC or laptop (and/or via a USB hub) is not as efficient as charging it directly from a wall mains USB adapter, because the power often gets interrupted. Ideally for the best charge you should turn the phone off and use a wall/mains socket USB lead, so as give a direct, constant, power supply to charge a battery. A typical full charge is done in two hours. If you charge this way and the battery still has issues buy a new one.
Click to expand...
Click to collapse
First of all, the Phone is manufactured in 11W41 (2011 Week #41) and the battery in 11W39 (2011 Week #39)
I use a tipical Micro USB charger which does not connect to the wall with USB but the cable directly integrated into the adapter...
And the phone's shipped official cable to charge throught my PC...
The battery worked fine before i forgot to delete battery stats and flashed a ROM...
After that, all ROM is getting fake battery data...
After using my phone i noticed:
-When the phone displays 70-80% charge, the battery actually have 10-15%
-When the battery reach 0% the phone not just jumps to 0% but the Phone shut down within a half second (as no more energy)
-When i charge it to 3-4% the phone show 80% again...
-So i can charge it to about 10 or max 15% when the OS detect 100% and does not charge it further more, which prevent me from properly re-calibrate the battery stats, cuz 10-15 will be always the max charge of the battery...
Now i'm looking for some kind of Mod / App that fake the Battery level to the OS (for example lock it to 5% and the OS continue to charge the battery) i know its dangerious cuz if i'm not aware i'll overcharge it and it will die permanently, but i have no better idea ATM...
Update: Sometimes after my phone dies from no remaining electron in the battery It displays 5% charge when i switch it on while connected to a charger (the only way i can switch it on) And starts to increase.. (5-6-7-8 etc..)
But sometimes it instantly jumps up to 70-80% if i think right when the screen switches of..
So i enabled "No-screen-off-whili-on-charger" and letit charging..
Will notice you about the result...
RabirX said:
First of all, the Phone is manufactured in 11W41 (2011 Week #41) and the battery in 11W39 (2011 Week #39)
I use a tipical Micro USB charger which does not connect to the wall with USB but the cable directly integrated into the adapter...
And the phone's shipped official cable to charge throught my PC...
The battery worked fine before i forgot to delete battery stats and flashed a ROM...
After that, all ROM is getting fake battery data...
After using my phone i noticed:
-When the phone displays 70-80% charge, the battery actually have 10-15%
-When the battery reach 0% the phone not just jumps to 0% but the Phone shut down within a half second (as no more energy)
-When i charge it to 3-4% the phone show 80% again...
-So i can charge it to about 10 or max 15% when the OS detect 100% and does not charge it further more, which prevent me from properly re-calibrate the battery stats, cuz 10-15 will be always the max charge of the battery...
Now i'm looking for some kind of Mod / App that fake the Battery level to the OS (for example lock it to 5% and the OS continue to charge the battery) i know its dangerious cuz if i'm not aware i'll overcharge it and it will die permanently, but i have no better idea ATM...
Update: Sometimes after my phone dies from no remaining electron in the battery It displays 5% charge when i switch it on while connected to a charger (the only way i can switch it on) And starts to increase.. (5-6-7-8 etc..)
But sometimes it instantly jumps up to 70-80% if i think right when the screen switches of..
So i enabled "No-screen-off-whili-on-charger" and letit charging..
Will notice you about the result...
Click to expand...
Click to collapse
try reflash stock.ics ftf should fix this
Already tried, the Stock rom always showed 100% charge, and when the battery ran out, just powered off...
(Jumped from 100 to 0 instantly)
As i mentioned, in the reply you quoted, today it started charging from 0...
It went good, but somewhy, it just stopped at 26% and not a single volt went into the Battery...
As i Pulled out the Cable, the indicator jumped to 100 instantly...
Can you link several stock ROMs ?
I've tried with the 4.0.4 Android
but maybe the 2.3 can still work with it...
RabirX said:
Already tried, the Stock rom always showed 100% charge, and when the battery ran out, just powered off...
(Jumped from 100 to 0 instantly)
As i mentioned, in the reply you quoted, today it started charging from 0...
It went good, but somewhy, it just stopped at 26% and not a single volt went into the Battery...
As i Pulled out the Cable, the indicator jumped to 100 instantly...
Can you link several stock ROMs ?
I've tried with the 4.0.4 Android
but maybe the 2.3 can still work with it...
Click to expand...
Click to collapse
but i think theres some HW damage. even if not rhe battery maybe some config chip is broken or whatever on the board. normally flashing a stock.ics.ftf resloves all software issues, as its resets all stuff to factory..
anyway, here u can find links to other android versions: http://talk.sonymobile.com/t5/Andro...y-Bean-ICS-Ice-Cream-Sandwich-and/td-p/154389
bejunk said:
but i think theres some HW damage. even if not rhe battery maybe some config chip is broken or whatever on the board. normally flashing a stock.ics.ftf resloves all software issues, as its resets all stuff to factory..
anyway, here u can find links to other android versions:
Click to expand...
Click to collapse
One solution still, that my frind has the same phone as me, so when i meet him, he can charge my battery to really full and maybe when i insert it to my phone it might work...
I've a friend that was updated his s4 zoom to kitkat and also got rooted, then his phone is unable to charge...
when the battery come to 0% then he tried to charging the phone (it should show the battery icon and still like that until we turn on the phone) but his phone always on automaticly and his phone dead after that cause not optimally charged (still 0%) so it's always turn on then turn off automaticly until he stop to charge the phone...
Now he just turn on the download mode then charging the phone for several hours then he turn on the phone so he'll get the battery charged around 10-20% then charging it normaly.so,is there any way to fix this?
thx.
If you are charging with device stock charger then it should charge properly but if you are using any other charger of samsung then it won't charge properly.
It is a thing with voltage. Normal charger are output .5 A volt and s4 zoom charger are 1 A.
Also you can try out battery calibration app from paly store to delete old rom battery traces.
Sent from my SM-C105