Hi,
I tried patching my new gene P3400i direct using Orefkov's method i followed all the instructions supplied like first installing the driver if you are in Vista.. m in vista i did the same ... then switched off my cell removed SD card and sim then pressed camera button .. so on.. tricolor... USB written at bottom of the phone screen then where it was written open "mtty1_42.exe" and Press the button "USB" in the window that opened but i didnt get any window with USB written, attaching the screenshot of the window that pops up after running mtty1_42...
kindly help!!
check your PM.
done with bricking and reviving!! spl patched
thanx alot
Hi Suraj,
did u get a solution for the problem..m too facing the same
rahulbitly1 said:
Hi Suraj,
did u get a solution for the problem..m too facing the same
Click to expand...
Click to collapse
more better you look and follow guide have given by krazy_about_technology ~ http://forum.xda-developers.com/showpost.php?p=3181506&postcount=3
hi rahul go with the steps in tutorial...
first you've to brick your device with olipro then bring it back using orefkov
The device is bricked and i am unable to recover it using the steps mentioned in the guide. It shows the following information on tricolor screen:
ONBL 1.17.0000
SPL 1.10 Olip
Whwn i run MTTY no usb button appears. M using xp for patching the spl.
Related
Hello
I have a problem with my Prophet and he needs to go to the factory..i need to install wm5 ,i have a wm6 rom and when i downgrade to wm5, the pda goes to bootloader and appears the following window:
ERROR 302 UPDATE ERROR
The Rom Update Utility has encountered communications errors during the update process. The Program will guide you step-by-step to recover from the errors so you can continue with the update!
I have the following advice but it stop´s on bootloader..
Need urgency help! Tks
tiagofa said:
Hello
I have a problem with my Prophet and he needs to go to the factory..i need to install wm5 ,i have a wm6 rom and when i downgrade to wm5, the pda goes to bootloader and appears the following window:
ERROR 302 UPDATE ERROR
The Rom Update Utility has encountered communications errors during the update process. The Program will guide you step-by-step to recover from the errors so you can continue with the update!
I have the following advice but it stop´s on bootloader..
Need urgency help! Tks
Click to expand...
Click to collapse
if u are in Bootloader mode the one in three color mode.. U can downgrade surely with PDA viet temp.
In Boot loader mode just reconnect your device to pc through USB . and launch the PDA VIET program..
It should be work.
doesn´t work..
is there any connection with SD slot card doesn´t work ?.. ?? :S
help.. :S
u r using vista right?
u should do that with xp
be sure that with xp u can fix it 100%
no, i+m using xp.. still doens´t work..
i think my prophet dies :S
try flashing NVID wm5 when in bootloader. if you were successfull flash HardSPL and after that you original ROM!
First, disable any firewall
Put the prophet in bootloader (3-clored screen) by pushing CAM button and punching the reset hole at the bottom. When you realease the stylus, the colors should appear.
Then, before connecting your prophet to the PC, first DISable the "Allow USB connection" option in the connectionsettings box of ActiveSync.
After that connect the bootloadermoded Prophet to your PC, it conects as an ordinairy USB device. Then run the RUU of your choice.
probably the better idea is to send a snapshot of your display in fault mode.
do that with a camera. it could be useful to identify the state of your error.
i'm not skilled but here you can find a pool of powerfull developers.
jork
problem solve
problem.. usb port lol :S
I have HT7 Phone it bricks during upgrading the SPL because it had WM5 and I went to install WM6
I can boot the Phone in Recovery Mode ( Holding the Camera Button and Boot ). Three Color Screen and I can communicate with the phone through the MTTY but during installing the Update it says ERROR 300
is there anyway to get the phone alive again ?
Thanks for your Help
** I have Kaiser and it's not mine , it was belong to my friend and I damaged his phone
PS : Phone is out of warranty and there is no service center here , also I can't use the JTAG Method
jafer mainly error 300 comes in when you are using wrong rom update utility... atleast in my case...after running spl pgm from phone and mtty program make sure you run the rom update utility inside the spl folder before running the rom update utility inside the rom folder... hope this helps.. and make sure that the rom is for old gene...
which spl its nowing at the tricolor screen now... oref or olipro?
which spl its showing at the tricolor screen now... oref or olipro?
ONBL 1.10.0000
SPL 1.07.oref
Thank you
Could you please explain more , where to get those files
I got Unbricker from here
http://forum.xda-developers.com/showpost.php?p=2784291&postcount=66
Thank you again
Question : when TriColor Launched can I re-flash the original firmware ? i don't know what to do now
Please look at the stickey, krazy has made quite a good tutorial about flashing etc and has all the tools hyperlinked. LoL
Hi Thanks but please don't refer me to reads topics , because i've already read all of them
The Phone is HT7 , during the upgrade it bricks , I used the " Orefkov " but it seems it only works for new Phones
Anyway by no I can Boot the Phone in Tri Color Mode but when i try to upgrade a rom it says ERORR 300
is there any way to BOOT the Phone through the SD Card ? I already had the same issue with another phone , I boot the phone with SDCard and it became alive again !!
But I don't know the Instructions for this GENO Crappy Phone
try removing the SD card and update the ROM. BTW as far as i know oref Is for new Gene. post a query on the right thread and ankit or krazy or any proficient member will definitely help you out. or you may pm basha for help.
I have ELF & I usually update its ROM
I tried updating my DAD's GENE but now I am stuck...
The phone isnt starting except the BOOT LOADER
In boot loader its showing
ONBL 1.17.0000
SPL 1.10.Olip
I tired all GENE ROMs but its showing UPDATE ERROR 300 [This update utility cannot be used for you PDA. Please get newer Update Utility]
Please help me..!!!
Please help MODS..!!!
Also tell me how to use .NBH files for GENE I mean is CUSTOM RUU is ok???
& if yes then which of the 6 options is to be selected..!!!
I am using VISTAS...!!!
sugestion
hi
as per ur nos giving it is a old gene(SPL 1.10.Olip is for old gene see my sign) my suggestion is
go to the link below download the ROM for OLD GENE also download a new ROM utty besfen ROM comes with the utty u can also use these roms for ur Gene see 2nd link provided i think ur existing Rom utty is corrupted
besfen has also provided original wm6 u can also try that also
good luck
http://forum.xda-developers.com/showthread.php?t=467796 - Krazy ROM
http://forum.xda-developers.com/showthread.php?t=505156 - Besfen ROM
heartsurfer008 said:
I have ELF & I usually update its ROM
I tried updating my DAD's GENE but now I am stuck...
The phone isnt starting except the BOOT LOADER
In boot loader its showing
ONBL 1.17.0000
SPL 1.10.Olip
I tired all GENE ROMs but its showing UPDATE ERROR 300 [This update utility cannot be used for you PDA. Please get newer Update Utility]
Please help me..!!!
Click to expand...
Click to collapse
haree said:
hi
as per ur nos giving it is a old gene(SPL 1.10.Olip is for old gene see my sign) my suggestion is
go to the link below download the ROM for OLD GENE also download a new ROM utty besfen ROM comes with the utty u can also use these roms for ur Gene see 2nd link provided i think ur existing Rom utty is corrupted
besfen has also provided original wm6 u can also try that also
good luck
http://forum.xda-developers.com/showthread.php?t=467796 - Krazy ROM
http://forum.xda-developers.com/showthread.php?t=505156 - Besfen ROM
Click to expand...
Click to collapse
Mr HAREE I tried with the "OLD_GENE_ORIGINAL_WM6" ROM but I am having same UPDATE [300] error..!!!
I am trying every ROM available for GENE please guide me..!!!
My cells manufacture date is AUGUST 2008..!!!
Can you tell me which CUSTOM RUU to use for GENE .nbh files & which option of all those is to be used cause there is no SPL1.10.Olip in it & also the CID unlocker for GENE from bootloader cause thats what only I can access now..!!!!
& another thing in "SPL Unlocking Tools-SPL updater-Orefkov"
"wcescomm.exe" in step 4
I am not getting USB in step 6. "Run mtty1_42.exe programm, and press button "USB""
NOTE: - I am using VISTA
try this
http://forum.xda-developers.com/showthread.php?t=513329
give answer to the program as follows:
step 1 no "1"
step 2 yes "2"
press no in the error message
step 3 no "n"
then mtty application will start, follow the steps thr
stupidgye said:
try this
http://forum.xda-developers.com/showthread.php?t=513329
give answer to the program as follows:
step 1 no "1"
step 2 yes "2"
press no in the error message
step 3 no "n"
then mtty application will start, follow the steps thr
Click to expand...
Click to collapse
Its not helping..!!!!
I already have old GENE..!!!
MTTY is not working on VISTAS..!!!
try this
hi
as per the ur spl mentioned and mine is the same so urs is a old gene i hope the numbers mentioned is right now try this
1.off the phone
2.take batter out press the power button for few secs around 3-4 secs
3.put battery back into the phone keep pressing camera button and power on the phone this should get u the tricolor screed if u get it good attached USB cable and flash an new ROM with ROm utty
or
press camera button and restart the phone with stylus this should also get u the tricolor
if u down load the besfenROM it also has the Rom utty with the ROm us this one and not the ROM utty u already have with u
good luck
heartsurfer008 said:
Its not helping..!!!!
I already have old GENE..!!!
MTTY is not working on VISTAS..!!!
Click to expand...
Click to collapse
heartsurfer008 said:
I have ELF & I usually update its ROM
I tried updating my DAD's GENE but now I am stuck...
The phone isnt starting except the BOOT LOADER
In boot loader its showing
ONBL 1.17.0000
SPL 1.10.Olip
I tired all GENE ROMs but its showing UPDATE ERROR 300 [This update utility cannot be used for you PDA. Please get newer Update Utility]
Click to expand...
Click to collapse
http://forum.xda-developers.com/showpost.php?p=2953612&postcount=2
or meet me at 8pm IST on yahoo or msn messenger pm me your id
ankit360 said:
http://forum.xda-developers.com/showpost.php?p=2953612&postcount=2
or meet me at 8pm IST on yahoo or msn messenger pm me your id
Click to expand...
Click to collapse
I am ONLINE, my GENE has started but need your help for updating..!!!
heartsurfer008 said:
I am ONLINE, my GENE has started but need your help for updating..!!!
Click to expand...
Click to collapse
Pls Explain how it could be happent?? does the update process interupted??
use windows XP
1. disconect the usb cable
2. press camera, then reset, release reset but still press camera, release it if the screen show tri color
3. connect the cable
4. if it say found new hardware, install usb driver for vista, it is in the package you download from thread to did hard SPL.
http://www.4shared.com/file/81084740/fa599d63/SPL_Unlocking_Tools.html
5. after the driver installation finish, just run Romupdateutility.exe
Still messed up..!!!
BesFen said:
1. disconect the usb cable
2. press camera, then reset, release reset but still press camera, release it if the screen show tri color
3. connect the cable
4. if it say found new hardware, install usb driver for vista, it is in the package you download from thread to did hard SPL.
http://www.4shared.com/file/81084740/fa599d63/SPL_Unlocking_Tools.html
5. after the driver installation finish, just run Romupdateutility.exe
Click to expand...
Click to collapse
Well as I said I tired to update the ROM & I messed up but now used XP & got th e the ROM to its ORIGINAL condition..!!!
I want to update the ROM, I tired all the ROM roms but having the same update 300 error, My GENE is AUGUST 2008 manufactured & has SPL 1.10.Olip..!!!
So I need a proper CID unlocker & the proper BOOT LOADER UPADTE & RUU..!!!!
Can you help me???
& are you on any networking site cause its easier to communicate..!!!
Facebook : - http://www.facebook.com/profile.php?id=1442055873
Orkut : - http://www.orkut.co.in/Main#Profile.aspx?uid=13511036999101959478
heartsurfer008 said:
Well as I said I tired to update the ROM & I messed up but now used XP & got th e the ROM to its ORIGINAL condition..!!!
....[/url]
Click to expand...
Click to collapse
Is your Gene working at the moment with the .Olip SPL? If yes, then your Gene is already unlocked.
Try any ROM you wish, just make sure that its post says that it is for "Old Gene". You may try a lot of Good ROMs from this forum, I can't suggest you any specific since its against my principle.
Best of Luck and happy flashing?
try to flash ur device on that tri color screen
if it is unlocked then it will definitely get flashed with any ROM for old gene, and if their is some problem them u probably have a new gene sso try orekfov method to unlock
Why in the world people dont want to read the tutorial properly before flashing, dont you guys give a damn to the phone that you purchased using your heard earned money, doesn't it deserve a little bit of your grey matter?.
First of all, there is no problem in unlocking phone from Vista so i request you guys to not spread this myth. In VIsta, you only need to downgrade your activesync drivers to windows xp ones and everything else goes smooth as pie. If you dont even know how to upgrade your pc drivers even after reading the guide and using the helpful driver update wizard that Windows Vista provides, i advice you to stay away from all this unlocking stuff, this is strictly not for you untill you study how driver updating works in Windows. And all this driver updating stuff is written in the Tutorial as a vital step, still people manage to skip it.
Secondly, if you had given even a little glance at tutorial you would know that if the Olipro SPL doesn't works on a phone, it is a new gene and the Orefkov's method must be used. After using that, phone gets alive right on that moment.
So as always, i wont try to help any futher, this is not a kids forum. If you consider me rude, good for you. But i just can't tolerate ignorance of this level.
Good luck.
krazy_about_technology said:
Why in the world people dont want to read the tutorial properly before flashing, dont you guys give a damn to the phone that you purchased using your heard earned money, doesn't it deserve a little bit of your grey matter?.
First of all, there is no problem in unlocking phone from Vista so i request you guys to not spread this myth. In VIsta, you only need to downgrade your activesync drivers to windows xp ones and everything else goes smooth as pie. If you dont even know how to upgrade your pc drivers even after reading the guide and using the helpful driver update wizard that Windows Vista provides, i advice you to stay away from all this unlocking stuff, this is strictly not for you untill you study how driver updating works in Windows. And all this driver updating stuff is written in the Tutorial as a vital step, still people manage to skip it.
Secondly, if you had given even a little glance at tutorial you would know that if the Olipro SPL doesn't works on a phone, it is a new gene and the Orefkov's method must be used. After using that, phone gets alive right on that moment.
So as always, i wont try to help any futher, this is not a kids forum. If you consider me rude, good for you. But i just can't tolerate ignorance of this level.
Good luck.
Click to expand...
Click to collapse
@ krazy_about_technology, sorry but I am not a NOOB, i have updated many ROM's but I am using VISTAS BLACK version by AMIT AGARA so I couldn't
update or technically DEGRADE the ACTIVE SYNC, that is the prob with it..!!!
& I have read the whole tutorial almost 10 times but still it didn't help me...
I have tried all old & new ROMs both using VISTAS & XP but my GENE is not getting updated..!!!
ERROR
Well try on different computer then. Use an genuine, clean copy of Vista or XP and you will succeed.
Done that
krazy_about_technology said:
Well try on different computer then. Use an genuine, clean copy of Vista or XP and you will succeed.
Click to expand...
Click to collapse
Do you think I haven't tried that???
I have done it on a CLEAN original valid version of XP but the same prob..!!!
Just check out that "UPDATE ERROR 300", I find that something unusual..!!!
Just see the PIC I have uploaded above this..!!!"
Hmm... Have you tried using the Orefkov unlocker method? What output is it giving? Try doing it after removing the battery, holding down the power button for 15 seconds and then then putting battery back and restarting phone in bootloader mode. I will try to get more info on this in the meanwhile.
I upgrade my rom and now he stucks on de first screen when windows mobile show i do everything i can and i don no what do more
The multi port program give-me this error
Cmd>ls boo.bin
clean up the image temp buffer at 0x8C100000 Length 0x03A00000
BOOTLOAD_PAGE_TABLE_BASE_C_VIRTUAL= 0x8C080000
Clear image temp buffer done .
MTTYDownloadImage
Not allow operation!
Error : DownloadImage return error (code = 0xFFFFFFFF)
Is everything i can do to my gene come back to life???????
Please Help me
Do you already do a SPL unlock?
If yes, just flash with another ROM.
Go to bootloader by press and hold camera then reset, release reset but still hold camera untill tri color appear, connect usb cable to pc then flash again with another ROM.
How thing i have all ready done that?but show-me how i do to see if i done well
When im restarting the pda the information tha show is
onbl 1.07.0000
spl 1.07.0000
gsm 02.71.90
os 1.17.0.0
After that screen goes to windows mobile screen and stuck
But is i do the combinations of the power button and camera i go to the 3 colors screen but when i do a update the program go to 2 % and reset
Please help-me
I think i all ready done that. But show-me how i do?
When i start the pda when arrive to the screen with the windows mobile picture stuck in there.
The information that i have in the begining is
onbl 1.07.0000
spl 1.07.0000
gsm 02.71.90
os 1.17.0.0
When i startup the device i can go to the 3 colors screen but when i tried to
upgrade the rom t when arrive at 2 % the device reset and give-me a error
i don now what i do more please help-me
@tonysucre do HSPL
hi
as per the nos u have posted u have not done HSPL
ur spl should end with .olip or .oref at the end instead of .0000
go to the tut given by Krazy and read many times use the tools and do the needful given in the same section viabhav has also given a tool
chek on both good luck
tonysucre said:
I think i all ready done that. But show-me how i do?
When i start the pda when arrive to the screen with the windows mobile picture stuck in there.
The information that i have in the begining is
onbl 1.07.0000
spl 1.07.0000
gsm 02.71.90
os 1.17.0.0
When i startup the device i can go to the 3 colors screen but when i tried to
upgrade the rom t when arrive at 2 % the device reset and give-me a error
i don now what i do more please help-me
Click to expand...
Click to collapse
haree said:
hi
as per the nos u have posted u have not done HSPL
ur spl should end with .olip or .oref at the end instead of .0000
go to the tut given by Krazy and read many times use the tools and do the needful given in the same section viabhav has also given a tool
chek on both good luck
Click to expand...
Click to collapse
Can you give-me the link of the tutorial?
Tks
@haree
buddy you are wasting your time .
There is a thread named upgrading ... by krazy as well as a thread by vaibhav named automatic SPL Updater. Just search a bit, son.
or may be you can take the cell to haree who will patch it for you
I Have already tried that but the thing but i cant put thing in the memory phone only in the sd card
Help please
after upgrade to 6.5 screen showing windows mobile 6.5 onyl
I used SumitsProUsersROM_WM6.5_build21815_OldGene_Fixed to upgrade its struck at windows mobile 6.5 screen only nothing happening.
not able to flash again. Aslo want to note that while I was ugrading it shows me something like "sudden loss of power"
Pls help my phone is not working now.
thaks
recharge the battery for mare than 1 hour and try again
After 6 hours of trying to change spl to flash the rom i haven´t manage to do anything more ist´s exactaly the same that i have all ready i have download a lot´s o rom´s and nothing i have tried the to do updating the spl by the sd card and nothing happen because i can´t put anything in the memory of the phone i only can put thing in the card from my computers card reader to trying to change the spl to 1.10-Olipro to flash the rom but i can´t
I don´t no what i have do more?
please anyone with the same problem can help-me
Tks
what error are u getting while upgrading?
vaibhav_batra_the_techguy said:
what error are u getting while upgrading?
Click to expand...
Click to collapse
error 270
is the same that a told is star to upgrading and in the 2 % the phone restarts and give-me that error i thing is because spl is 1.7.0000 or not?
I just see i hav cid lock and and dont now i unlock ?any help
@tonysucre
see
below link as i had told u before u have not done HSPL
u go to the below links and save them on ur comp and Read no one is going to hand hold u and u dont need it with such nice tutes given pls not im a guy with Zero tech skills and i did it so u can as my boss would say its not rocket science
& i dont have any gene tools with me as i have upgraded to another phone (see my sign)
good luck
http://forum.xda-developers.com/showthread.php?t=513329
http://forum.xda-developers.com/showthread.php?t=472169
tonysucre said:
Help please
Click to expand...
Click to collapse
When I attach my niki in bootloader mode with my pc and the i try to do hardspl there comes white screen showing a bar 0% but it did not go ahead like other htc it stays on and after some time there come an error 262 saying this
the rom update utility has encountered a communication error during the update process........etc
i also acted step b step on the guidence of this program but in vain so plez help me how can i hard spl my niki to upgrade new rom ......plzzzzzzzzz
Nofear99 said:
When I attach my niki in bootloader mode with my pc and the i try to do hardspl there comes white screen showing a bar 0% but it did not go ahead like other htc it stays on and after some time there come an error 262 saying this
the rom update utility has encountered a communication error during the update process........etc
i also acted step b step on the guidence of this program but in vain so plez help me how can i hard spl my niki to upgrade new rom ......plzzzzzzzzz
Click to expand...
Click to collapse
if u have already spl 1.5 on ur device then,after runing hard spl 1.22,the moment u c the tri colour on ur device,take the data cable off from pc.when u c 'serial' on ur device,insert the cable again.the process will be complete.
regards
thanks to answer but same problem...
deepankerjha said:
if u have already spl 1.5 on ur device then,after runing hard spl 1.22,the moment u c the tri colour on ur device,take the data cable off from pc.when u c 'serial' on ur device,insert the cable again.the process will be complete.
regards
Click to expand...
Click to collapse
i can see on boot loader mode my spl is 1.16.0000
niki200 cpld-4
plzz tell me another solution
i will be thankful to u
Nofear99 said:
i can see on boot loader mode my spl is 1.16.0000
niki200 cpld-4
plzz tell me another solution
i will be thankful to u
Click to expand...
Click to collapse
is ur device sim unlocked?moreover i think u have already hard spl installed on ur device pal.