The in-call speaker on my wife's Aria doesn't consistently work for calls. I've replaced the digitizer on it, but I don't think it's hardware related, because I took the battery out while it was on, and when I started it up again, it worked; and sometimes it works, then doesn't, then does.
What happens is when she calls or is called the speaker just doesn't work. She transfers the sound to the external speaker and it works fine.
She's running the Liberated ROM (not sure what version, sorry; I can find out if needed).
Thanks for any help!
It's probably a loose connection.
Using a wired headset has screwed 2 arias for me now.sometimes I can wiggle the plug before I remove it and get the speaker to work but generally I just turn speakerphone on and turn the volume all the way down to use the ear speaker.fairly common problem.
Sent from my Liberty using XDA App
drumist said:
It's probably a loose connection.
Click to expand...
Click to collapse
I'm going to agree on this one. I've taken my Aria apart more times than I probably should have... the first cellphone I've ever repaired on my own, so go figure.
My bet would be that the in-call speaker is still in place, but loose. If you open it up again, the piece you're looking for is maybe a half-inch long rectangular block with two prongs on one side. If the phone is sitting screen up, the prongs should be facing down with the points towards the top of the cell phone. It sits in a little recess above the lcd assembly.
You need to push the piece up so it's snug in it's little recess. Easy peasy.
If you've already done a digitizer replacement, you should have the tools to do a quick check and make sure the speaker is secure in the proper position.
I still think it may be a loose speaker connection, but I also think mtnlion could be right, too.
When the in-call speaker does not work, does the phone show an icon in the notification bar that indicates that a headset is connected?
In any case, I do think it's a hardware issue and not a software issue. But if the OP really wants to be certain, he can install another ROM and see if the same problem occurs.
Yeah, I took the thing apart again, and stretched those prongs a bit to make the speaker fit more snugly; hasn't had the problem since. But I think now the seal isn't quite as tight as it used to be so her screen "squishes". That'll be another day.
Thanks for the thoughts on it.
Adhesive issues
I had that issue too. To fix it, all I had to do was use a space heater (or a blow dryer) on the phone (take the battery, sim card and SD card out first) for about 15 minutes. Then take it and smoosh it underneath something flat and heavy like a book, but make sure to put something down beneath it so the screen doesn't get scratched. Once it cools down, it should be significantly less squishy.
Related
1- it's reboot many times without any reason(I read one thread about it but i dont understand what to do!!)
2-sometimes 2gb microSd card loosing?(i cant open it from phone...only rebooting helps!!)On other devices card works good!
The usual reason for a 3125 rebooting is that the battery cover has gotten worn down to the point that the micro-switch under it is not fully depressed. There are multiple potential wear-down points. The hooks on either side and the tabs at the bottom can get worn or even broken. There is also a raised pad at the lower left (looking at the cover from the inside) than can get worn, as can the contact point on the switch.
Typical solution, providing the hooks and/or tabs are not totally broken off, is to put a thin piece of plastic or cardstock between the microswitch (lower right of the batter compartment) and the cover. It's a temporary solution (it tends to get continually worse), so if this fixes it, you should check eBay for a replacement cover.
That said, I had a phone that reset for another reason, which I never found. So it could be something else. I ended up buying a phone with a bad keyboard and doing a keyboard transplant from my old one.
I had the same problem and I'll tell you what I did. Open the back cover and you will see a little black switch next to the sim card/below the battery. I took a pair of needle-nose pliers and just twisted that sucker right out like a bad tooth (carefully though, you don’t want to tear up the foil on the board). Then I put a small spot of solder on the two contacts that the switch used to connect to. Never had a random reboot ever again. From then on, just make sure you take the battery out first before ever messing with the sim/sd card.
That worked for me.
Thanks
dexx40steve said:
I had the same problem and I'll tell you what I did. Open the back cover and you will see a little black switch next to the sim card/below the battery. I took a pair of needle-nose pliers and just twisted that sucker right out like a bad tooth (carefully though, you don’t want to tear up the foil on the board). Then I put a small spot of solder on the two contacts that the switch used to connect to. Never had a random reboot ever again. From then on, just make sure you take the battery out first before ever messing with the sim/sd card.
Click to expand...
Click to collapse
i have the very same problem and this sounds like a perfect long term solution.. any chance of getting picture of ur mod for morons like me who need visual stimulation?
regards,
Hey all,
I have no idea what the hell is going on with my tab. I did not have any issues and all of a sudden lost any and all sound. I was running Vegan 5.11 and then installed Vegan Ginger RC1 and thats when, I think, it started happening. I NVFlashed back to stock and still no sound. Tried to install a bunch of other roms and still no go. I am absolutelly lost of what to do. BTW I tried the earphone plug in and unplug but nothing. The only way anything happens is through bluetooth.
Help!!!!!
System & Alarm OK, No Media Sound
Let my G rested for a few days and last night the sound was cutting in/out. Today the sound is completed back. I am still on stock ROM, did not do anything special, just turned on the “Audible Selection” and rebooted a few times.
I guess it was too much water while putting on Skinomi screen protector...
**************************************************************************
Now it’s confirmed, media sound works, as long as the screen is off.
Tried to play music with stock ROM, as soon as I "saw" music is playing, hit power button to turn off screen, then I can hear music, but as soon as the screen is on, media sound is silent.
Would be great if sound and screen can both be on again. Please HELP!!
***************************************************************************
I installed Skinomi screen protector and after that lost media sound. During the installation I tried to power down my G but as soon as I squeegee the screen (even after confirmed power off) G will come back on and of course a lot of commands were popping up on screen since I could not power it down. After Skinomi installation I lost media sound. At first I thought I drowned the speakers but then realized system and alarm sounds still work, just no media sound.
Then I had another interesting discovery. If I tried to watch Youtube video and while it’s playing, hit the power button to shut off the screen, I can hear the media sound when the screen is off for a little while. As soon as the screen is back up, media is silent again.
I also tried the headset trick and switched from Vegan 5.1.1 to TnT Lite to stock ROM. I believe the silence was caused by pressing keys in special sequence but don’ t know what it was since I was using a squeegee. Otherwise I have had my G since Feb2011 and never had any problem.
I am praying to all you android GODs out there and hoping I can find an answer to have the media sound back again.
I fixed my sound issue that sounds identical
You should appreciate the beauty of the problem and the solution...
After thinking it had to be a software issue (because the sound worked as long as I turned the screen off) and finding no one at all who knew what to do I was about to give up on the sound on my g tablet.
But then I had a crazy thought - what if it was a hardware issue where either a contact on the motherboard melted together or somehow the sound cable was interfered with by a loose connection.
If you open the gtablet case - Gulp! Its actually not that bad...
Using an eyeglass repair kit screwdriver, gently remove the rubber circular pads on the back of the tablet.
Underneath you will discover screws that the eyeglass screwdriver can unscrew.
After unscrewing all four, use a credit card to gently slot between the seals of the casing all the way around. eventually the casing will separate without problems.
Once open, and with the tablet now facedown on your lap. look at the lower right section of the motherboard for a thin brown wire that is connected near the 3.5 mm jack up and connected on the other end near the middle right of the motherboard.
Mine was untaped and loosly laying over two contacts of the motherboard. All I did was gently position that little wire away from those two contacts to the left (right of the metal screen backing wall) so they would not touch those contacts.
Believe it or not - that solved the problem. Turns out that the two contacts when touched by the wire cause the sound to short off. But when not touching them, everything works fine.
The reason the sound would work before when the screen was turned off in sleep mode was because IF THE SCREEN IS OFF THERE IS NO LONGER A CURRENT GOIND THROUGH THE CONTACTS!!! Beautiful....
gently snap the cover back on and ensure it all snaps back all the way around, reinsert the screws and replace the little rubber backings and turn you tablet back on.
Good luck!
What was that? I can't hear you over my newly working tablet speakers!!!
Very interesting. Thanks.
I've been puzzling over (and, frankly, have not been able to diagnose) a similar problem. Looks like bad engineering on VS's (or Malata's) part if 5 users have encountered this same problem.
Karmas coming your way if the user verifies that what you suggested fixed his problem.
Thanks. I had the cover off before to resolder the power jack to the board. This time I accidentally pulled on the headphone cord.
amoffa said:
You should appreciate the beauty of the problem and the solution...
After thinking it had to be a software issue (because the sound worked as long as I turned the screen off) and finding no one at all who knew what to do I was about to give up on the sound on my g tablet.
But then I had a crazy thought - what if it was a hardware issue where either a contact on the motherboard melted together or somehow the sound cable was interfered with by a loose connection.
If you open the gtablet case - Gulp! Its actually not that bad...
Using an eyeglass repair kit screwdriver, gently remove the rubber circular pads on the back of the tablet.
Underneath you will discover screws that the eyeglass screwdriver can unscrew.
After unscrewing all four, use a credit card to gently slot between the seals of the casing all the way around. eventually the casing will separate without problems.
Once open, and with the tablet now facedown on your lap. look at the lower right section of the motherboard for a thin brown wire that is connected near the 3.5 mm jack up and connected on the other end near the middle right of the motherboard.
Mine was untaped and loosly laying over two contacts of the motherboard. All I did was gently position that little wire away from those two contacts to the left (right of the metal screen backing wall) so they would not touch those contacts.
Believe it or not - that solved the problem. Turns out that the two contacts when touched by the wire cause the sound to short off. But when not touching them, everything works fine.
The reason the sound would work before when the screen was turned off in sleep mode was because IF THE SCREEN IS OFF THERE IS NO LONGER A CURRENT GOIND THROUGH THE CONTACTS!!! Beautiful....
gently snap the cover back on and ensure it all snaps back all the way around, reinsert the screws and replace the little rubber backings and turn you tablet back on.
Good luck!
What was that? I can't hear you over my newly working tablet speakers!!!
Click to expand...
Click to collapse
I have a Verizon HTC Thunderbolt and I regularly use the flip feature while on the phone to enable my speaker phone. I turn my phone face down on a flat surface and the speaker phone is automatically enabled. I reverse the process and the speaker phone is automatically disabled. Recently this feature stopped working and now when I put my phone face down the speaker phone no longer automatically starts. Can you please help me restore this feature?
Go into your sound settings and make sure "flip for speaker" is checked.
I confirmed that "Flip for Speaker" is checked. While Googling for a possible solution I encountered a recommendation to try gently dropping the phone, face down, on a soft surface, to "recalibrate its proximity", I tried that and it worked. My speaker phone now works again when I flip it over.
Could you be a little more specific about how you got it to work exactly because I haven't been able to get mine to work since day 1. Basically list the steps you did in order for you to get it working again. Thanks
I held my phone, face down, over the carpet, about 6 inches from the ground and deliberately dropped it. Then I picked it up, started a phone call, flipped my phone like normal and it automatically switched to speaker phone.
I did that and it stil didn't work. I had to start a call then drop it like you said and then the speaker turned on. After ending the call I called again to see if that fixed it but it still didn't work. In order for me to get it to work i have to drop it everytime I want the speaker to turn on?????
Troubleshooting steps:
1) hardware or software? Download "android sensor data" from the market. Observe the readings as you rotate your phone. If the readings don't move, your sensor is broken and you need a replacement.
2) if they do move, and accurately, its software. Google will yield ways to re-calibrate as well as how to enable the feature.
Sent from my ThunderBolt using Tapatalk
I'll be damned...that worked!!!
Ya, you don't have to drop the phone to get it to work. You can usually just "tap" the phone against your hand or shake the phone to get the sensors to get "unstuck".
I have a question for those with the issue. Are you using any kind of case with a magnetic clasp?
I know they say it doesn't affect the phones, but ever since I had a G1, I've never used any cases with magnets in them because they always seemed to mess up all the sensors.
Just something I've observed over the years.
I am using the seidio Convert 3-in-1 but i'm pretty sure there's no magnet in it.
Still working on the sensor info. Will post results
Thanks for all the help
I've had the exact same issue with mine since day 1 I got the phone. It has never worked with that feature and when I mentioned it to Verizon they had no answers. I'm glad someone brought this up so I could fix it as well!
seabhac said:
I've had the exact same issue with mine since day 1 I got the phone. It has never worked with that feature and when I mentioned it to Verizon they had no answers. I'm glad someone brought this up so I could fix it as well!
Click to expand...
Click to collapse
You also have to remember that the flip feature also seems to use the prox sensor, so if you just "flip" the phone in the air, it will not activate the speakerphone. I can understand this, because let's say you are holding the phone in your watch hand and you flip the phone quickly to check the time. You would not want the phone to go to speaker for that.
It has to detect the "flip" and also that you flipped the phone against something (like a tabletop, etc).
I recalibrated my sensor by going to display then calibrate sensor. After that I made a call and the only time it actualy works is when you lay it down on a flat surface, but then when you go to pick it up the speaker turns off.. WTF.... The whole point of that is to be able to flip your phone and have the speaker turn on. Why even have it if you have to manually do it during a call anyway? Sounds like they didn't put a whole lot of thought into the functionality of the flip for speaker phone. I use my speaker all the time but what good is it to set your phone down to turn the speaker on, of course you will be able to hear the person talking but what about them being able to hear you?
I'm not using a case at all.
Karine said:
I'm not using a case at all.
Click to expand...
Click to collapse
But when it changes position from flat to any other does the speaker still stay on or does it turn off?
Since using the drop technique I described to fix my flip feature, it now works when I flip it regardless of the type of surface.
MomentFreak said:
But when it changes position from flat to any other does the speaker still stay on or does it turn off?
Click to expand...
Click to collapse
As long as the prox sensor is tagging, you will have speaker phone.
Easy way to test.
Call a number. Turn the phone over while holding it in the air. Cover the prox sensor (the sensor just to the left of the speaker grill at the top of the phone). Speaker phone will come on. Move hand away from the prox sensor, speaker phone will go off.
So I did the test and when I covered the speaker it turned on and stayed on even after removing my hand and putting it in an upright position.
Is that what it's supposed to do?
MomentFreak said:
So I did the test and when I covered the speaker it turned on and stayed on even after removing my hand and putting it in an upright position.
Click to expand...
Click to collapse
Ahh, I just tested it as well and you are correct!
Seems it does not constantly check the prox sensor.
If you turn the phone back over the speaker phone will be on and unless I cover the prox sensor again, it will stay on.
Kinda of odd since it did not work that way when I first got it. I wondering if maybe something with the custom roms or the kernel, may be changing the behavior?
sawvellra26 said:
Try updating tasker. Worked for me
Click to expand...
Click to collapse
How do you update tasker and what exactly is it?
yesterday I decided against my better judgement to try and take apart my x10 to see if I could get to the speakers, it sounded distorted during phone calls when the volume was all the way up. I used the dissasembly guide here: http://www.xperiax10.net/2010/05/10/xperia-x10-disassembly-guide/
however once, i started reading the guide, i realized I had to basically gut the entire phone to get to the main call speaker, so i put it back together. all i did was take out the screws, removed the lower support and used a credit card to pry between the covers and worked my way down. thats as far as i got, I had the back cover off and then I reassembled after reconsideration. however, the phone didn't work when i turned it back on. I mean, it works and I can see the backlighting on the screen but no logo or anything. I know it's actually booting into android because I can unlock the phone by memory and proper finger placement without even having the display working. I hear the "click" when it unlocks my phone and the volume/updown beeps. i've even heard my personal set notification tone go off a couple times. however, aside from the screen not working (besides backlighting), it wont respond to a phone call or chime when you send it a text message. If i use a different phone to call mine, it rings several times until you leave a voice message like normal. so, its not acting like its off. so again, I know it's actually booting into android.
after further inspection I realized that there is a ribbon cable on the bottom right hand side (battery side up) particularly close to where the covers snap together. I don't know if I did it with the credit card swipe or the covers weren't aligned well when I snapped it back together but I can see one little trace with a magnifying glass and a flashlight where it was "nicked" or scored. one teeny tiny little thing and my phone is inop.... does anyone have any suggestions? maybe like where I can get that ribbon cable? I'd start over with a new phone but the ebay prices are ridiculous. this use to be an ATT free upgrade phone and now its discontinued. I really doubt you can fix a ribbon cable... im feeling pretty helpless here.
I think you should send to shop to get professional repair before it getting worse.
My S3 got wet this morning, after sitting in rice through the day it will power on... however as soon as I put the battery in you can hear the speaker giving off this little static sounding gurgling noise. Once the phone powers up the speaker does not work regardless if on the phone or speaker. Also when I call someone, they cannot hear me. It is not recognizing my SD but is recognizing my SIM. The back and edit / settings button on the bottom of the phone work ~75% of the time.
My question is... if I buy another S3 (I see them often going at a discount with cracked screens) can I take the guts out of the new phone and just use my current LCD / glass / case?
Falken231 said:
My S3 got wet this morning, after sitting in rice through the day it will power on... however as soon as I put the battery in you can hear the speaker giving off this little static sounding gurgling noise. Once the phone powers up the speaker does not work regardless if on the phone or speaker. Also when I call someone, they cannot hear me. It is not recognizing my SD but is recognizing my SIM. The back and edit / settings button on the bottom of the phone work ~75% of the time.
My question is... if I buy another S3 (I see them often going at a discount with cracked screens) can I take the guts out of the new phone and just use my current LCD / glass / case?
Click to expand...
Click to collapse
Yes, you can, well, mostly i think, the parts that don't contain data, but if you will only replace the screen you are good to go.
But please, if you don't know how to do that, go pass that to someone experienced so nothing is messed up.
Cheers.
Yes you can just use screen setup, you can use the motherboard, speaker, mic etc from the good phone and put it in the old screen chassis. this will not fix any screen, touch, light up key etc issues though.